Planet Technology GSD-503 User's Manual
Contents
1. 10 100 1000Mbps Gigabit Ethernet Switch GSD 503 GSD 504 GSD 803 GSD 804 User s Manual Trademarks Copyright PLANET Technology Corp 2005 Content subjects to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested and found to2. Contact MDI MDI X Media Dependant Media Dependant Interface Interface Cross 1 Tx transmit RX receive 2 Tx transmit RX receive 3 Rx receive TX transmit 4 5 Not used 6 RX receive TX transmit 7 8 Not used The standard cable RJ 45 pin assignment 12545678 2 The standard RJ 45 receptacle connector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection 2010 A33110 000 CE
3. the cable to the network devices such as printer servers workstations or routers etc Note Connection to the switch requires UTP Category 5 network cabling with RU 45 tips For more information please see the Cabling Specification in Appendix A Step5 Supply power to the switch A Connect one end of the power cable to the switch B Connect the power plug of the power cable to a standard wall outlet When the switch receives power the Power LED should remain solid Green 3 SWITCH OPERATION 3 1 Address Table The Switch is implemented with an address table This address table composed of many entries Each entry is used to store the address information of some node in network including MAC address port no etc This information comes from the learning process of Ethernet Switch 3 2 Learning When one packet comes in from any port the Switch will record the source address port no And the other related information in address table This information will be used to decide either forwarding or filtering for future packets 3 3 Forwarding amp Filtering When one packet comes from some port of the Ethernet Switching it will also check the destination address besides the source address learning The Ethernet Switching will lookup the address table for the destination address If not found this packet will be forwarded to all the other ports except the port which this packet comes in And these ports will t
4. A Switch Specification Switch Architecture Store and forward Address Table 8K entries auto learning ageing Shared Data Buffer 112K bytes 144KB Flow Control IEEE 802 3x full duplex operating and flow control Packet Control Runt amp CRC filtering Broadcast storm control Switch Fabric 10Gbps 16Gbps Standard Conformance Network Standards IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3ab Gigabit Ethernet and IEEE802 3x flow control Operation Temperature 0 50 C 10 to 90 Non condensing Humidity 40 70 C Regulation Compliance FCC CE 2 INSTALLATION This section describes the functionalities of the Gigabit Ethernet Switch s components and guides how to install it on the desktop Basic knowledge of networking is assumed Please read this chapter completely before continuing 2 1 Product Description The PLANET GSD 503 GSD 504 and GSD 803 GSD 804 are 5 8 ports 10 100 1000Mbps Ethernet switches in a compact housing for easily desktop placement The GSD 503 GSD 504 and GSD 803 GSD 804 provide 10 16Gbps non blocking switch fabric 8K MAC Address table all support 802 3x full duplex flow control and also offers wire speed packet transfer performance without risk of packet loss All five eight RJ 45 copper interfaces support 10 100 1000Mbps auto negotiation for optimal speed detection thro
5. as follows Chapter 2 Installation The chapter explains the feature functionality and the physical installation of the Switch Chapter 3 Switch operation The chapter explains the Gigabit Ethernet Switch transmit operation Chapter 4 Troubleshooting The chapter explains the troubleshooting of the Gigabit Ethernet Switch Appendix A This chapter contains cable information of the Gigabit Ethernet Switch 1 3 Product Features 0 Er Complies with IEEE802 3 10Base T IEEE802 3u 100Base TX and IEEE802 3ab 1000Base T IEE802 3x full duplex flow control compliant back pressure half duplex flow control 10 100 1000Mbps 5 8 port Gigabit Switch RJ 45 8K MAC address table auto ageing 112K GSD 503 GSD 504 144K GSD 803 GSD 804 bytes packet buffer 9 6K Jumbo packet size support Per port Auto MDI MDI X detection Non blocking Store and Forward switching architecture Automatic source address learning and aging 1 4 Product Specifications Model GSD 503 GSD 504 GSD 803 GSD 804 Hardware Specification Network Ports 5 10 100 1000Base T RJ 45 MDI MDI X ports 8 10 100 1000Base T RJ 45 MDI MDI X ports Dimensions W x D x H 155 x 86 x 26 mm 503 155 x 86 x 26 mm 803 170 x 87 x 32mm 504 170 x 87 x 32 mm 804 Weight KG 0 42 503 0 22 504 0 43 803 0 24 804 Power Requirement External Power adapter 12V 1
6. comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at its own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Revision PLANET Gigabit Ethernet Switch User s Manual FOR MODELS GSD 503 GSD 504 GSD 803 GSD 804 Rev 1 0 May 2005 Part No 2010 A33110 000 1 INTRODUCTION 1 1 Package Contents Check the contents of your package for following parts O Gigabit Ethernet Switch x1 O User s manual x1 O Power adapter x1 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 How to Use This Manual This Gigabit Ethernet Switch User Manual is structured
7. formance is bad Solution Check the full duplex status of the Ethernet Switch If the Ethernet Switch is set to full duplex and the partner is set to half duplex then the performance will be poor Why the Switch doesn t connect to the network Solution Check the LNK ACT LED on the Switch Try another port on the Switch Make sure the cable is installed properly Make sure the cable is the right type Turn off the power After a while turn on power again This page intentionally left blank Appendix A A 1 Switch s RJ 45 Pin Assignments 1000Mbps 1000Base T Contact MDI MDI X 1 BI_DA BI_DB 2 BI_DA BI_DB 3 BI_DB BI_DA 4 BI_DC BI_DD 5 BI_DC BI_DD 6 BI_DB BI_DA 7 BI_DD BI_DC 8 BI_DD BI_DC Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard A 2 10 100Mbps 10 100Base TX When connecting your 10 100Mbps Ethernet Switch to another switch a bridge or a hub a straight or crossover cable is necessary Each port of the Switch supports auto MDI MDI X detection That means you can directly connect the Switch to any Ethernet devices without making a crossover cable The following table and diagram show the standard RJ 45 receptacle connector and their pin assignments RJ 45 Connector pin assignment
8. itch is actively sending or receiving data over that port Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a surge suppression device may also help to protect your switch from being damaged by unregulated surge or current to the Switch or the power adapter 2 2 Installing the Switch This part describes how to install your Gigabit Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented Note This switch does not need software configuration 2 2 1 Desktop Installation To install the switch on desktop simply follow the next steps Step1 Attach the rubber feet to the recessed areas on the bottom of the switch Step2 Place the switch on desktop near a DC power source Step3 Keep enough ventilation space between the switch and the surrounding objects Note When choosing a location please keep in mind the environmental restrictions discussed in Chapter 1 Section 1 4 Product Specification Step4 Connect your switch to network devices A Connect one end of a standard network cable to the 10 100 1000 RJ 45 ports on the Back of the switch B Connect the other end of
9. r panel of GSD 504 Q PLANET eINK ACT O O O O O wo 5 Port Gigabit Ethernet Switch Neen Corman Fae ae GSD 504 fe Co0o0 Ow 1 PWR 23 4 5 Figure 2 3 GSD 503 front panel Figure 2 4 GSD 504 rear panel Figure 2 5 amp 2 6 show the front panel and rear panel of GSD 803 Q PLANET eink ACT OO 0 0 0 0 O Owo 8 Port Gigabit Ethernet Switch Aeon amp anmueson C000000 Ow O oo0o000000w GSD 803 PWR 123 4 567 8 Figure 2 5 GSD 803 front panel 12V DC Figure 2 6 GSD 803 rear panel Figure 2 7 amp 2 8 show the front panel and rear panel of GSD 804 Q PLANET nk ACT CO OO OOO OC 0 8 Port Gigabit Ethernet Switch Ries eee Sees RE GSD 804 0 C0000000w PWR 123 45 67 8 Figure 2 7 GSD 804 front panel Figure 2 8 GSD 804 rear panel 2 1 3 LED Indicators LED Color Function PWR Green Lit Power on 1000 Green Lit indicate that the port is operating at 1000Mbps Blink indicate that the switch is actively sending or receiving data over that port 100 Green Lit indicate that the port is operating at 100Mbps Blink indicate that the switch is actively sending or receiving data over that port 10 Green Lit indicate that the port is operating at 10Mbps Blink indicate that the sw
10. ransmit this packet to the network it connected If found and the destination address is located at different port from this packet comes in the Ethernet Switching will forward this packet to the port where this destination address is located according to the information from address table But if the destination address is located at the same port with this packet comes in then this packet will be filtered Thereby increase the network throughput and availability 3 4 Store and Forward Store and Forward is one type of packet forwarding techniques A Store and Forward Ethernet Switching stores the incoming frame in an internal buffer do the complete error checking before transmission Therefore no error packets occurrence it is the best choice when a network needs efficiency and stability The Ethernet Switch scans the destination address from the packet header searches the routing table provided for the incoming port and forwards the packet only if required The fast forwarding makes the switch attractive for connecting servers directly to the network thereby increasing throughput and availability However the switch is most commonly used to segment existing hubs which nearly always improves overall performance An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters Due to the learning function of the Ethernet switching
11. the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table This information is subsequently used to filter packets whose destination address is on the same segment as the source address This confines the network traffic to its respective domain reducing the overall load on the network The Switch performs Store and forward therefore no error packets occur More reliably it reduces the re transmission rate No packet loss will occur 3 5 Auto Negotiation The STP ports on the Switch have built in Auto negotiation This technology automatically sets the best possible bandwidth when a connection is established with another network device usually at Power On or Reset This is done by detect the modes and speeds at the second of both device is connected and capable of both 10Base T and 100Base TX devices can connect with the port in either Half or Full Duplex mode 1000Base T can be only connected in Full duplex mode 4 TROUBLESHOOTING This chapter contains information to help you solve problems If Giga Switch is not functioning properly make sure the Ethernet Switch was set up according to instructions in this manual Some siations cannot talk to other stations located on the other port Solution The address table may contain older information than of the address table of that node Please power down to refresh the address information Per
12. ugh RJ 45 Category 3 4 5 or above cables MDI MDI X auto detection is provided for direct wire connection to any Ethernet device without requiring crossover cables 2 1 1 Product Overview PLANET GSD 503 GSD 504 GSD 803 GSD 804 are Gigabit Ethernet switches with 5 8 RJ 45 10 100 1000 Mbps ports for high speed network connectivity The switches can also automatically identify and determine the correct transmission speed and half full duplex mode of the attached devices with its 5 8 ports The Gigabit port with jumbo frame feature supported can handle extremely large amounts of data transmission in a secure topology linking to a backbone or high power servers This product also supports store and forward forwarding scheme to ensure low latency and high data integrity eliminates unnecessary traffic and relieves congestion on critical network paths With an intelligent address recognition algorithm the switches could recognize up to 4K different MAC address and enables filtering and forwarding at full wire speed 2 1 2 Switch Front Panel Figure 2 1 amp 2 2 show the front panel and rear panel of GSD 503 Q PLANET sINK AcT O O O O Om 5 Port Gigabit Ethernet Switch ent k Coomans 626 6 OO O OO000 0 GSD 503 PWR 123 4 5 Figure 2 1 GSD 503 front panel 12V DC Figure 2 2 GSD 503 rear panel Figure 2 3 amp 2 4 show the front panel and rea
Download Pdf Manuals
Related Search