Pitco Frialator L22-303 User's Manual
Contents
1. IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the eguipment Model Serial Date Purchased KL Ma Q Z za Service Manual I8 Water Cooker Computer Covering P N PP11375 DMO This manual details the operation and adjustment of the 18 Water Cooker computer developed for the Pitco water cooker and rethermalizer products This microprocessor control offers the latest cooking technology including temperature and time compensation that requires no user adjustments for consistently cooked product Other features include drain valve interlock faulty probe detection selectable melt cycles beeper volume and cook temperature Each product key may be programmed with cook shake and hold times to keep pace with changing menus over time This manual reveals all adjustments that are possible by keyboard entry including passwords The target audience for this manual is the Service Technician L22 303 Rev 0 01 07 I8 Water Cooker Computer Service Pitco P N PP11375 1 0 2 0 3 0 4 0 Table of Contents Key Locations and Functions 1 1 1 2 1 3 1 4 1 5 1 6 To turn the appliance ON To turn the appliance OFF To start a cook To cancel a cook To Check Actual and Set Temperatures To vie2. 22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 4 2 Cancel Delay Setting This setting controls the length of time in seconds necessary for a key press to cancel an active cook timer A setting of zero disables this cancel delay setting and a cook timer cancels as soon as a product key is pressed A cancel delay setting of greater than zero enables this cancel delay and a product key must be pressed and held for the duration of time in seconds equal to the current cancel delay before the active cook timer will cancel For example if the cancel delay is set to 5 then a product key will have to be pressed and held for 5 seconds before the active cook timer will cancel The default value is zero The maximum value that can be entered is 9 NOTE The Cancel Type section 4 4 must be set to 1 before this Cancel Delay feature will work See section 4 4 Cancel Type Setting for more information With the control display showing SERVICE press product key 2 The display will show CAN DLYx where x is the current cancel delay value Enter the new cancel delay using product keys 0 9 Press the program key to save this setting The display will now show SERVICE Continue on to the remaining service menu options below or press the program key twice to return to normal operation display shows either READY ACT xxx F or FILLING 4 3 Minimum On Cycle Time Setting This setting adjusts the m
3. 310 154 4 1525 9 475 246 1 268 61 150 65 6 18695 315 157 2 1433 0 480 248 9 257 15 155 68 3 16981 320 160 0 1346 7 485 251 7 246 30 160 71 1 15446 325 162 8 1266 6 490 254 4 236 00 165 73 9 14069 330 165 6 1192 1 495 257 2 226 24 170 76 7 12823 335 168 3 1122 8 500 260 0 216 96 NOTE The resistance of either probe lead measured to the frame of the appliance should read as an open on a meter resistance gt 1Mohm 16 L22 303 Rev 0 01 07 8 0 Physical Dimensions I8 Water Cooker Computer Service Pitco P N PP11375 i 1 81 gp nama g 9 00 i J i o 5 Hi pa OO IR 50 DOOR FOR SERIAL YR MR di USED FOR OEM DOWN I i G _ fF a L22 303 Rev 0 01 07 I8 Water Cooker Computer Service Pitco P N PP11375 NOTES 22 303 Rev 0 01 07 NOTES L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 In the event of problems with or In the event of problems with or questions about your order please questions about your equipment please contact the Pitco Frialator factory at contact the Pitco Frialator Authorized 800 258 3708
4. P N PP11375 4 7 3 Low Dead Band Adjustment This setting adjusts the vat temperature limit below the set temperature where the heat demand output will be ON to apply heat to the vat At vat temperatures below this value heat will be applied to the vat For example if the set temperature is 180 F and the Low Dead Band value is 3 then at vat temperatures below 177 F heat will be applied to the vat The value range of this setting is 1 9 degrees With the control display showing MORE press product key 3 The display will 3 now show DB LO xj where x is the current Low Dead Band value Enter the E new value using product keys 1 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 4 High Dead Band Adjustment This setting adjusts the vat temperature limit above the set temperature where the heat demand output will be OFF At vat temperatures egual to or greater than this value the heat demand output will be OFF For example if the set temperature is 180 F and the High Dead Band value is 1 then at vat temperatures at or above 181 F heat will not be applied to the vat A setting of zero for this value will force the heat control output OFE when the vat temperature eguals the set temperature T
5. US and Canada only or Service and Parts ASAP covering your 603 225 6684 Worldwide area or contact Pitco at the numbers listed to the left www pitco com MAILING ADDRESS P O BOX 501 CONCORD NH 03302 0501 SHIPPING ADDRESS 10 FERRY ST CONCORD NH 03301 L22 303 Rev 0 01 07
6. 3 to turn this output ON Release the key to 2 turn this output OFF The control display will show HEAT DEM 4 5 4 Side On SO or Transfer Output 4 Press product key 4 to toggle this output ON or OFF The control display will show TRANSFER im 4 5 5 Drain Switch DVI Input Press product key 5 to view the state of the drain switch input The control display will show either D CLOSED or D OPEN depending on whether the drain switch is open or closed 4 5 6 Heat Feedback HFB Input Press product key 7 to view the state of the heat feedback input The control display will show either FB ON or FB OFF depending on whether a heat feedback signal is present or not 4 5 7 Fill Done Input Press product key 8 to view the state of the fill done input The control will display either NO FILL or FILL depending on whether a fill signal is present or not Press the program key to exit it out of this menu option The display will now show T SERVICE Continue on to the remaining service menu options below or press the li program key twice to return to normal operation display shows either READY ACT xxx F or FILLING 10 L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 4 6 Recovery Test Value This control records the heat up time for the appliance A poorly running appliance will have an increased recovery time Select this menu option to view the la
7. al operations display shows either READY ACT xxx F or FILLING 3 2 Password Settings The factory default setting for this control is password disabled The default factory password for Level 1 and Level 2 programming is 6684 This default password will always work regardless of the new password that can be entered using this option With the control display showing SELECT press product key 2 The display will show 2 SET PASS Press product key 0 to scroll between the two options PASS REQ and NO PASS Press the program key to save this setting If the NO PASS option was selected the control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to normal operations display shows either READY ACT xxx F or FILLING l the PASS REG option was selected the display will show PASSxxxx where xxxx is the current password Enter the new password using the product keys 0 9 Press the program key The control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to normal operation display shows either READY ACT xxx F or FILLING 3 3 Beeper Volume Setting The volume setting of the beeper alarm can be set to low 1 medium 2 and high 3 The default value for the beeper volume is 3 With the control di
8. be given a value of 5 The maximum value for this setting is 9 degrees With the control display showing MORE press product key 1 The display will 1 now show RDY LO x where x is the current Low Ready Level setting Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 2 High Ready Level Adjustment This setting allows the READY idle message to be displayed a number of degrees above the current set temperature For example if the current set temperature is 180 F and the READY idle display message is to be displayed from 180 F to 185 F then this setting should be given a value of 5 The maximum value for this setting is 9 degrees With the control display showing MORE press product key 2 The display will 2 now show RDY HI x where x is the current High Ready Level setting Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING L22 303 Rev 0 01 07 11 I8 Water Cooker Computer Service Pitco
9. he control will display TM4 mm ss where mm ss is minutes seconds then SH4 mm ss and HD4 mm ss as the current time settings for product key 4 2 0 To enter Level 1 Programming store manager Note The factory default setting for this control does not reguire an operator password to be entered However the operator password reguirement and value may be changed in section 3 2 Entry of a password when NOT reguired will not interfere with the programming process While there are no cook timers running and the control display shows either READY rei ACT xxx F or FILLING press the program key If the control displays PASS m enter the manager password or the default manager password 6684 using the product keys 0 9 The control display will show PROGRAM All of the Level 1Menu programming options shown below must begin with the control displaying this prompt PROGRAM A 2 1 To set the Cook Temperature With the control display showing PROGRAM press the thermometer key once The i f control display will show SET xxx F where xxx is the current setpoint temperature OOO m id Enter the new set temperature using the product keys 0 9 Press the program key Final once to save this setting The control display will show PROGRAM Continue on D to the next Level 1 Menu programming option below or press the program key again to exit it out of the Level 1 Menu The control display will
10. he value range of this setting is 0 9 degrees now show DB HI x where x is the current High Dead Band value Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING With the control display showing MORE press product key 4 The display will El 4 7 5 Control Temperature Average Setting This setting adjusts the number of times per second the vat temperature readings are averaged in the heat control process of the computer The default value for this setting is 6 The value range of this setting is 1 9 With the control display showing MORE press product key 5 The display will show AVER C x where x is the current control temperature average setting Enter the new value using product keys 1 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 6 Display Temperature Average Setting This option adjusts the number of times per second the vat temperature readings are averaged each second for displaying on the control display The default value for t
11. his setting is 12 The value range for this setting is 7 32 With the control display showing MORE press product key 6 The display will 6 show AVER Dxx where xx is the current display temperature average setting Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 service menu options below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 7 Minimum Fill Time Setting This setting adjusts the minimum length of time the heat control process in the computer will wait before applying heat to the vat when the vat is being filled with water Heat will be applied to the vat after the computer senses that the vat is full of water and the fill time counter expires The sensing of the water level in the vat takes precedence over the fill time counter In other words the computer will ignore this timer if it does not sense that the vat is full if the timer expires before the vat is full The default setting for this timer is 20 minutes 20 00 The value range for this timer is from 1 30 minutes With the control display showing MORE press product key 7 The display will 7 show FILLmm ss where mm ss is the current minimum fill time setting in minute
12. inimum time duration in seconds that the heat control output will be on when heat is applied to the vat The range of this setting is 1 30 seconds With the control displaying SERVICE press product key 3 The display will show 3 MINON xx where xx is the current minimum on cycle time in seconds Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show SERVICE Continue on to the remaining service menu options below or press the program key twice to return to normal operation display shows either READY ACT xxx F or FILLING 4 4 Cancel Type Setting The Cancel Type setting allows for two cook timer cancellation types If set to 1 then the Cancel Delay setting section 4 2 is used If the Cancel Type is set to 0 then a product key must be pressed three times in succession in order to cancel a cook and the Cancel Delay setting is ignored The default Cancel Type value is 1 show CANTYP x where x is the current cancel type value either 0 or 1 Press product key 0 to scroll between the two cancel type values Press the program key to save this setting The display will now show SERVICE Continue on to the remaining service menu options below or press the program key twice to return to normal operation display shows either READY ACT xxx F or FILLING With the control display showing SERVICE press product key 4 The control dis
13. ll begin to flash and the cook timer should appear on the computer display If multiple cook timers are running the cook timer with the least amount of time remaining will be displayed 1 4 To cancel a cook When the control display shows either READY or ACT xxx F press the desired E Press the product key to cancel a running cook timer If there are no other cook timers running the computer will return to normal operation and display either READY or ACT xxx F where xxx is the current vat temperature 1 5 To Check Actual and Set Temperatures Press the temperature key to check the actual vat temperature The control will je Ji sl momentarily display ACT xxx F where xxx is the current vat temperature and then return to normal operation 4 L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 To view the set temperature press the thermometer key twice The control will momentarily display SET xxx F where xxx is the set temperature i TJ and then return to normal operation and display either READY or PODO VOD ACT xxx F 1 6 To view the current Cook Shake and Hold timer settings the clock key followed by the desired product key for which you want to check the time settings For example press the clock key then product key 4 AN za Nj Noe a To view the current Cook Shake and Hold timer settings for a cook timer press AN ki T
14. n section 3 2 Entry of a password when NOT required will not interfere with the programming process While there are no cook timers running and the control display shows either READY ACT xxx F or FILLING press the program key If the control displays PASS k enter the manager password or the default manager password 6684 using the product keys 0 9 The control display will show PROGRAM To enter into the Level 2 Options Menu press product key 0 The control display will show SELECT The key indicators that light up will have options that can be adjusted Any key indicators that do not light up do not have options that can be adjusted k All of the Level 2 Options Menu programming options shown below must begin with the control displaying this prompt SELECT 6 L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 3 1 Fahrenheit or Celcius Temperature Display This control will display temperatures in Fahrenheit F or Celsius C degrees The default setting is degrees Fahrenheit F With the control display showing SELECT press product key 1 The display will show qT DEGREE n where n is the current setting either F or C Press the 0 key to scroll between the two options Press the program key to save the setting The control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to norm
15. nctions of the appliance If any faults are detected the control will turn all outputs OFF suspend any cooking functions that may be in progress and sound an alarm One of several alarm messages detailed below will appear on the control display If one if these alarms occur turn off the control see section 1 2 to reset the alarm 5 1 Open Probe Alarm PROBE OP Open temperature probe detection is standard on all Pitco controls This alarm will occur if the temperature probe is detected to be open All heating and cooking functions are suspended if this alarm occurs N L22 303 Rev 0 01 07 13 18 Water Cooker Computer Service Pitco P N PP11375 Pitco 5 2 High Temperature Alarm HIGH TMP This alarm will occur if the vat temperature exceeds the set temperature value by 35 F If a high vat temperature alarm occurs all heating and cooking functions are suspended 5 3 Drain Valve Alarm DRAINING and TURN OFF alternating This alarm message will appear on the control display if the drain valve on the appliance is opened while the control is ON All heating and cooking functions are suspended if this alarm occurs 5 4 Heat Failure Alarm HEAT and FAILURE alternating This alarm will occur if the control does not sense a pilot flame or if the high limit switch has tripped and needs resetting All heating and cooking functions are su
16. ntrol Alarm Displays 5 1 5 2 5 3 5 4 5 5 Open Probe Alarm High Temperature Alarm Drain Valve Alarm Heat Failure Alarm System Failure Alarm Electrical Connections J1 Probe Resistance Chart Physical Dimensions 22 303 Rev 0 01 07 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 16 17 18 Water Cooker Computer Service Pitco P N PP11375 Pitco 1 0 Key Locations and Functions Program Key Temperature Key Clock Key LO PiTco E AT NI E J VO O O IN Key Indicators 1 2 2 4 ai 9 Key Indicators TN ar Product Keys 8 Digit Display Product Keys 1 1 To turn the appliance ON If power is applied to the appliance plugged in and the control is off the display will be blank Turn on the control by pressing the power on off switch located on the right side of the control to the ON position The control will then briefly display the software version number and then display either READY ACT xxx F where xxx is the current vat temperature or FILLING if the appliance is being filled with water 1 2 To turn the appliance OFF Press the power on off switch to the OFF position The control display will be blank 1 3 To start a cook product key For example press product key 4 to start cook timer 4 The key indicator above the product key wi
17. play will ta 4 5 Diagnostics Menu This menu option allows for basic diagnostic testing of the inputs and outputs of the control By exercising outputs and examining inputs a determination can be made as to whether the appliance problem is related to the control computer In this menu each product key is assigned to a specific input or output on the control All control outputs in the ON state should produce 24VDC 10 on the appropriate pin on the controller connector All controller inputs require 24VAC or 24VDC 10 on the appropriate L22 303 Rev 0 01 07 9 I8 Water Cooker Computer Service Pitco P N PP11375 Pitco connector pin Controller inputs can be verified by the ON or OFF state of the key indicator above the appropriate product key With the control display showing SERVICE press product key 5 to enter into the diagnostics menu The control display will show either D CLOSED or D OPEN depending on whether the drain switch is open or closed Press the appropriate product key listed below to test the input output assigned to that key 4 5 1 Left Basket Lift LBL Output 1 Press product key 1 to toggle this output ON or OFF The control display will show L BASKET 4 5 2 Right Basket Lift RBL Output 2 Press product key 2 to toggle this output ON or OFF The control display will show R BASKET 4 5 3 Heat Demand HD Output 3 Press and hold product key
18. rs are active and the heat control outputs are enabled to control the heating of the vat In Timer mode the cook timers are active but the heat control outputs are disabled NOTE Do not use the Timer mode setting on Solstice fryer models With the control display showing SELECT press product key 7 The display will show 7 the current setting of either CONTROL or TIMER Press product key 0 to scroll between the two options Press the program key to save this setting The control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to normal operation display shows either READY ACT xxx F or FILLING 4 0 To Enter Level 3 Service Programming service technician Note The factory default setting for this control does not reguire an operator password to be entered However the operator password reguirement and value may be changed in section 3 2 Entry of a password when NOT reguired will not interfere with the programming process While there are no cook timers running and the control display shows either READY Ia ACT xxx F or FILLING press the program key If the control displays PASS _ H enter the manager password or the default manager password 6684 using the product keys 0 9 The control display will show PROGRAM To enter into the Level 3 Service Menu key in the service password of 6685
19. s seconds Enter the new timer value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the remaining more service menu option below or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 8 Pilot Flame Sense Timer Adjustment This menu option adjusts the timer that is used by the control to detect an absence of a pilot flame in the appliance during a cold start During a cold start of the appliance the control will expect to sense a pilot flame before this timer times out If on a cold start a pilot flame is not sensed by the control when this timer expires the control outputs will be turned OFF heat will be turned off and an alarm will sound The default value for this timer is 60 seconds The value range of this setting is 10 60 show FLAME xx where xx is the current pilot flame sense timer value in seconds Enter the new value using product keys 0 9 Press the program key to save this setting The display will now show MORE Continue on to the other more service menu options above or press the program key three times to return to normal operation display shows either READY ACT xxx F or FILLING With the control display showing MORE press product key 8 The display will ki 5 0 Control Alarm Displays This control continually monitors the basic overall fu
20. show either READY ACT xxx FILLING and the control will return to normal operation or 2 2 To change Cook Shake and Hold Timer settings 2 2 1 Cook Time With the control display showing PROGRAM press the clock key The display will show SELECT and all eight key indicators will light up Press the desired product key for the cook time to change For example press product pa key 4 The control display will show 4TM mm ss indicating that Cook Timer 4 ki has a timer setting of mm ss in minutes seconds Enter the new cook time using the product keys 0 9 Press the clock key to save exit this setting and ee proceed to the next step 2 2 2 or press the program key three times to exit out of this programming option and to return to normal operation 22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 Pitco To deactivate the cook timer on a product key enter in a cook time of zero for this key 2 2 2 Shake Time Shake Time is an alarm that sounds while a cook timer is running to prompt an operator to shake the product in the basket The default value for shake time on a product key is zero which disables this alarm To enable the shake time alarm a non zero value must be entered for this setting The shake time value must be less than the cook time With the display showing RSH mm ss where n is the desired product key SH means Shake and mm ss is the time value in min
21. spended if this alarm occurs a gt 1 re ss mT Il I J Il gt PS ho A Koh ii ii ll il hy J Me Pi 5 5 System Failure Alarm SYSTEM This alarm will occur if the control detects a shorted temperature probe All heating and cooking functions are suspended if this alarm occurs 14 L22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 6 0 Electrical Connections J1 J1 Connection Type Nominal Notes 1 24VAC IN PWR 24VAC 24VAC 20 15 50 60Hz 2 24VAC COM PWR OVAC AC RETURN 3 PROBE THERMISTOR Resistance varies with vat temperature 6 22K 4 PROBE PROBE ohms at 212 F 5 DVI INPUT 24VAC DC Drain Valve Interlock 6 HFB INPUT 24VAC DC Heat FeedBack 7 24VDC COM PWR OVDC DC RETURN 8 HD OUTPUT 24VDC Heat Demand 9 SO TRANSFER OUTPUT 24VDC Side On TRANSFER 10 RBL OUTPUT 24VDC Right Basket Lift 11 LBL OUTPUT 24VDC Left Basket Lift 12 FILL DONE INPUT 24VAC DC Fill Done signal NOTE The Diagnostics Menu sections 4 0 and 4 5 can be used to check the inputs and outputs on this connector 22 303 Rev 0 01 07 18 Water Cooker Computer Service Pitco P N PP11375 Pitco 7 0 Probe Resistance Chart Probe Resis
22. splay showing SELECT press product key 3 The display will show VOLUME x where x is the current volume setting Press product key 0 to scroll through the volume options The control will beep using the volume setting currently shown on the display Press the program key to save this setting The control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to normal operation display shows either READY ACT xxx F or FILLING 3 4 Lanquage Selection This control can display text in English Spanish French German and Dutch With the control display showing SELECT press product key 4 The display will show the current language setting of either ENGLISH ESPANOL FRANCAIS DEUTSCH or HOLLANDS Press product key 0 to scroll through the language options Press the program key to save this setting The control display will show PROGRAM Press product key 0 to select more options below display shows SELECT or press the program key to return to normal operation display shows either READY ACT xxx F or FILLING 22 303 Rev 0 01 07 7 I8 Water Cooker Computer Service Pitco P N PP11375 Prrcoj 3 5 Control or Timer Mode Setting This control can operate in one of two basic modes Control or Timer mode The default mode setting is Control mode and is the setting for normal operation In this mode the cook time
23. st recorded recovery time for this appliance The recovery time is the length of time in seconds the appliance needs to heat the vat from 230 F to 280 F This menu option is for display only With the control display showing SERVICE press product key 7 The control display will 7 show Rxxx yyy where xxx is the last recorded recovery time for this appliance and yyy is the factory default recovery time Press the program key to exit it out of this menu option The display will now show SERVICE Continue on to the remaining service menu options below or press the program key twice to return to normal operation display shows either READY ACT xxx F or FILLING 4 7 More Service Menu Options With the control display showing SERVICE press product key 8 The display will show MORE for the More Service Menu The key indicators that light up will have options that can be adjusted Any key indicators that do not light up do not have options that can be adjusted All of the Level 3 More Service Menu programming options shown below must begin with the control displaying this prompt MORE 4 7 1 Low Ready Level Adjustment This setting allows the READY idle message to be displayed a number of degrees below the current set temperature For example if the current set temperature is 180 F and the READY idle display message is to be displayed from 175 F to 180 F then this setting should
24. tance in 5 F Increments Probe Probe Probe Probe g Probe Probe Temp Temp Resistance Temp Temp Resistance Temp Temp Resistance F Ohms F Ohms F Ohms 10 12 2 562734 175 79 4 11719 340 171 1 1058 23 15 9 4 483875 180 82 2 10716 345 173 9 998 09 20 6 7 417167 185 85 0 9812 350 176 7 942 00 25 3 9 360589 190 87 8 8995 355 179 4 889 67 30 1 1 312474 195 90 6 8255 360 182 2 840 78 35 1 7 271446 200 93 3 7586 365 185 0 795 10 40 4 4 236370 205 96 1 6979 370 187 8 752 38 45 7 2 206311 210 98 9 6427 375 190 6 712 41 50 10 0 180491 215 101 7 5926 380 193 3 674 95 55 12 8 158252 220 104 4 5470 385 196 1 639 87 60 15 6 139055 225 107 2 5055 390 198 9 606 96 65 18 3 122489 230 110 0 4675 395 201 7 576 09 70 21 1 108051 235 112 8 4329 400 204 4 547 09 75 23 9 95539 240 115 6 4013 405 207 2 519 86 80 26 7 84644 245 118 3 3723 410 210 0 494 24 85 29 4 75136 250 121 1 3458 415 212 8 470 16 90 32 2 66823 255 123 9 3214 420 215 6 447 49 95 35 0 59540 260 126 7 2991 425 218 3 426 13 100 37 8 53146 265 129 4 2785 430 221 1 406 02 105 40 6 47523 270 132 2 2597 435 223 9 387 04 110 43 3 42569 275 135 0 2422 440 226 7 369 14 115 46 1 38195 280 137 8 2262 445 229 4 352 24 120 48 9 34328 285 140 6 2113 9 450 232 2 336 29 125 51 7 30902 290 143 3 1977 3 455 235 0 321 21 130 54 4 27862 295 146 1 1851 0 460 237 8 306 94 135 57 2 25161 300 148 9 1734 3 465 240 6 293 46 140 60 0 22755 305 151 7 1626 1 470 243 3 280 69 145 62 8 20610
25. using the product keys 0 9 The control display will show SERVICE On oe The key indicators that light up will have options that can be adjusted Any key indicators that do not light up do not have options that can be adjusted All of the Level 3 Service Menu programming options shown below must begin with the control displaying this prompt SERVICE 4 1 Offset Temperature Seiting This setting allows the displayed temperature value to be offset degrees F to reflect the true center vat temperature while reading the probe tip temperature The default value is zero A setting of zero for the temperature offset will make the displayed temperature equal to the probe temperature The maximum offset value that can be entered is 20 With the control display showing SERVICE press product key 1 The display will show 1 OFF xx F where xx is the current offset value Enter the new offset value using the product keys 0 9 Press the program key to save this setting The control display will show either POSITIVE or NEGATIVE indicating that the offset value is positive or negative Press product key 0 to scroll between these two options Press the program key to save this setting The display will now show SERVICE Continue on to the remaining service menu options below or press the program key twice to return to normal operation display shows either READY ACT xxx F or FILLING 8
26. utes seconds enter the new shake time value using the product keys 0 9 NOTE the time value entered will be the time remaining before the end of the cook Press the clock key to save exit this setting and proceed to the next step 2 2 3 or press the program key three times to exit out of this programming option and return to normal operation DA Bi AY 2 2 3 Hold Time After a product is cooked it may stand in bins for a period of time Hold Time provides a timer to control how long a product stands in a bin After the hold timer expires an alarm will sound to inform the operator to cook more product The default value for hold time on a product key is zero which disables this alarm timer To enable the hold timer alarm a non zero value must be entered for this setting With the display showing nHDh mm ss where n is the desired product key HD means Hold and h mm ss is the time value in hours minutes seconds enter imi the new hold time value using the product keys 0 9 Press the program key ii three times to save and exit out of this programming option The control display will show either READY ACT xxx F or FILLING and the control will return to normal operation 3 0 To enter Level 2 Options Programming store manager Note The factory default setting for this control does not reguire an operator password to be entered However the operator password reguirement and value may be changed i
27. w the current Cook Shake and Hold timer settings To enter Level 1 Programming store manager 2 1 2 2 To set the cook Temperature To change Cook Shake and Hold timer settings 2 21 Cook Time 2 2 2 Shake Time 2 23 Hold Time To enter Level 2 Options Programming store manager 3 1 3 2 3 3 3 4 3 5 Fahrenheit or Celsius Temperature Display Password Settings Beeper Volume Setting Language Selection Control or Timer Mode Setting To enter Level Service Programming service technician 4 1 4 2 4 3 4 4 4 5 Offset Temperature Setting Cancel Delay Setting Minimum On Cycle Time Setting Cancel Type Setting Diagnostics Menu 4 5 1 Left Basket Lift LBL Output 4 5 2 Right Basket Lift RBL Output 4 5 3 Heat Demand HD Output 4 5 4 Side On SO or Transfer Output 4 5 5 Drain Switch DVI Input 4 5 6 Heat Feedback HFB Input 4 5 7 Fill Done Input 22 303 Rev 0 01 07 oN NNN O O O 0 0 Cn Mm a A A A A A R o o o o 09 10 10 10 10 10 10 5 0 6 0 7 0 8 0 4 6 4 7 18 Water Cooker Computer Service Pitco P N PP11375 Recovery Test Value More Service Menu Options 4 7 1 Low Ready Level Adjustment 4 7 2 High Ready Level Adjustment 4 7 3 Low Dead Band Adjustment 4 7 4 High Dead Band Adjustment 4 7 5 Control Temperature Average Setting 4 7 6 Display Temperature Average Setting 4 7 7 Minimum Fill Time Setting 4 7 8 Pilot Flame Sense Timer Adjustment Co
Download Pdf Manuals
Related Search