Home

Pioneer EFX-1000 User's Manual

1. 530 Als PERFORMANCE EFFECTOR omenal EFFEC USING BEAT EFFECTS BPM MODE 1 Select the BPM measurement mode Press the BPM MODE button so that the button lights together with the desired mode indicator AUTO MIDI TAP 2 Select effect type Press the DELAY ECHO PITCH ECHO TRANS FLANGER FILTER or PHASER button and the pressed button starts to flash 3 Select the sound range for the effect Press the button of the frequency LOW MID HI you wish to affect by the beat effect and the corresponding indicator lights 4 Select the beat with which the effect is to be synchronized Press a beat select button 1 8 1 4 1 2 3 4 1 1 2 1 4 1 or 8 1 to light the desired button 5 Apply an effect Press the lever towards you ON position to start operation release it and it returns to the center position OFF position In the center position OFF position the original sound is not affected Press the lever away from you to lock it in position so that the beat effect is applied also when the lever is released TIME BPM dial Set the desired effect time as in step 4 Turn the TIME BPM dial while holding down the TAP SHIFT button to make the desired BPM setting When also the BPM MODE button is held down BPM can be set in 0 1 increments TAP SHIFT button BPM can be manually adjusted by
2. DEPTH dial Sets the parameter 1 of each effect DIGITAL JOG BREAK METER Indicates the amount of control exercised by the Jog dial DIGITAL JOG BREAK METER WAH ZIP PHASE SHIFTER RNG HUMANIZER vocooeR ser JOG MEMORY PLAY JOG MODE HOLD O ON LOCK MAX CHARACTER ORIGINAL EFFECT MIX dial Adjusts the balance between the original sound and effects CHARACTER dial Sets the parameter 2 of each effect 6 lt DRB1369 gt DIGITAL JOG BREAK 1 Select the desired effect Press the desired effect button JET WAH PHASE SHIFTER RING ZIP HUMANIZER or VOCODER to flash the corresponding button 2 Apply the desired effect Turn the Jog dial either while pressing the lever towards you or pressing it away from you ON position As the Jog dial is turned parameters change gradually and the selected effect is applied When the dial rotation is stopped the parameter returns to normal When the lever is pressed towards you releasing it causes it to automatically return to the center OFF position HOLD button When this button is pressed so that the button indicator lights effects produced with the Jog dial will continue even when your hand is removed from the dial P 1 Hold the Jog memory button M depressed while rotating the Jog dial Effect changes produced w
3. CHARACTER j e a a MAX ea ame as e The MIX dial can be used to adjust the levels of the original and filter sounds gt RHYTHM mode Changes cutoff frequency of the low pass filter in synch with the TAP rhythm Max 8 TAP e The DEPTH dial is used to change the unique coloring of the sound by adjusting the amount of resonance When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to vary the cutoff frequency of the cyclic low pass filter e The MIX dial can be used to adjust the levels of the original and filter sounds 7 PHASER effect Causes a phase effect by applying a phase shifted sound to the original sound BPM mode Changes the frequency range to which the phase effect is applied at the interval set by the TIME dial e The DEPTH dial can be used to adjust the strength of the phase effect by changing the amount of resonance When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to adjust the cyclic changes in the phase effect e The MIX dial can be used to adjust the levels of the original and phaser sounds TIME CHARACTER A es eee in Phase effect change gt Time TIME CHARACTER Phase effect change gt Time TIME CHARACTER e i ee Max Phase effect change gt Time RHYTHM mode Changes the frequency subjected to phase effect in sync w
4. CHARACTER TIME BPM MODE 5 TAP 1 RHYTHM MODE 6 1 8 1 4 1 2 3 4 1 1 2 1 4 1 8 1 4 Rhythm REC beat select Beat Effects RHYTHM mode The beat effects RHYTHM mode function allows you to create a variety of effects synchronized with your own input rhythm 1 Use the RHYTHM MODE button to set to rhythm mode The RHYTHM MODE button lights 2 Use the beat effect select buttons to select the desired effect e Select from DELAY ECHO PITCH ECHO TRANS FLANGER FILTER or PHASER The selected effect button flashes See pages 10 11 regarding each effect 3 Use the EFFECT FREQUENCY buttons LOW MID HI to select the band to which the effect is to be applied When a button is pressed the button s indicator will light Each time a button is pressed it alternates ON OFF 4 Press rhythm REC button to set to REC mode e The BPM display will indicate r e If no rhythm has been input the unit will automatically enter the REC mode in step 1 5 Input the desired rhythm using the TAP button Input taps will be recognized as a tempo when occurring at intervals of less than 2 seconds Up to 8 taps can be input The counted taps RHYTHM TAP will be shown in the display During rhythm input the beat select button 1 1 will be selected 6 Select one of the beat select buttons to establish the overall time for the input rhythm The overall time f
5. o sele a 6 OG leo s 000000 00000 ose o DJ CD Player DJ CD Player 2 Connecting a DJ Mixer and an Audio Amplifier e When making connections do not connect both RCA pin on DJ mixer not provided with SEND and plug cables and phones plug cables for the same RETURN terminals connection function use either one or the other not e Connect using cables with phone plugs 1 4 inch 6 3 mm both Also if you wish to use analog connections do in diameter or RCA pin plugs not also make connections to the digital connectors digital signals are given priority when connected e For digital connections use RCA pin plug coaxial cables Set the OUTPUT fs SELECT switch in accordance with the connected component 8 lt DRB1369 gt BEFORE USE CONNECTIONS e Set the IN amp OUT LEVEL switch on the Effector to the 4 dB position INSOUT LEVEL Le OUTPUT AS AN OUTPUT fs SELECT 44 1 48 96 kHz lt i gt MASTER OUT ES on CA iol 4 a a a a n Stereo Amplifier DJ Mixer 3 Connecting a DJ CD Player and a DJ Mixer this e Connect the units using a cable with RCA pin plugs connection applies effects only
6. 1 1 is selected and a multiple of the rhythm can be selected with the beat select buttons 21 Beat effect beat interval indicators The indicators light to show the period of the effect time 22 Beat effect TIME BPM dial When rotated the effect time selected with the beat select buttons can be changed as desired If the dial is rotated while depressing the TAP button the BPM can be set as desired BPM manual input 23 BPM MODE button indicator Use to turn BPM mode ON and to select tempo measurement mode AUTO MIDI TAP During BPM mode the button lights If the TAP button is pressed tapped during BPM mode the mode switches to manual BPM measurement mode When power is first turned the mode defaults to AUTO measurement mode 24 TAP SHIFT button indicator During BPM mode When this button is tapped the BPM manual measurement mode is selected and the interval between two taps maximum interval 2 seconds is measured the corresponding EFFECT TIME and BPM count is displayed and the beat select button 1 1 is selected If the TIME BPM dial is rotated while pressing this button the BPM can be adjusted to an optional value BPM manual input During RHYTHM mode When this button is tapped the rhythm is input maximum tap interval 2 seconds up to maximum rhythm count 8 The beat select button 1 1 is selected Tap indicator Lights during normal use goes out only when TAP is pressed 25 Rhythm REC butto
7. consult your dealer or nearest Pioneer Service Station SPECIFICATIONS 1 General Power Supply eccccconocccccnnnnncncnnnnnanancnnnnnnnnns AC 110 V 240 V 50 60 Hz Power consumption Operating temperature Relative humidity 00 5 to 85 without condensation Weil Gh Ermita ai i n 2 4 kg 2 Audio Unit Sampling ratio is A D D A Resolutio enasna Frequency characteristics SIN TAO E Teasietecdcopees nies teeenk DiSto MON lustre Head Matti Inputlevel Nui 10 dBV 4 dBu 22 KQ Output level cuina 10 dBV 4 dBu RCA pin jacks 1kQ Phone jacks 1 kQ 10 dBV 4 dBu is switchable 26 lt DRB1369 gt 3 Input Output terminals Audio line input terminal RCA Din JACKS cccisccssecedsseevscgssesccasdsdesosecesiteiscanezachdoliniaesdeelesieaivasesss 2 Phone jacks 1 4 inch 6 3 mm in diameter eessen 2 Audio line output terminal RCA DIN ACKS anna Phone jacks 1 4 inch 6 3 mm in diameter Digital input terminal RCA Pin jackie 1 Digital output terminal RCA PIM ackiuiaa id eeted 1 EFX LINK connector mini DIN ned MIDI input terminal 5 pin DIN re MIDI output terminal 5 pin DIN oooonnncccccnnnconcnnnonanannnnnnnnrncnnnnnannnnns 1 4 Accessories Operating iNStrUCtiONS iasan 1 Digital link cable POWCP Cord ita dara NOTE Specifications and design are subject to possible modification without notice
8. utilizar este aparato corresponda a la tensi n necesaria es decir 230 V 120 V indicada en el panel posterior ADVERTENCIA Para evitar el peligro de incendio no ponga nada con fuego encendido como pueda ser una vela encima del aparato D3 4 2 1 4_A_Sp D3 4 2 1 7a_A_Sp PRECAUCI N PARA LA VENTILACI N Cuando instale este aparato aseg rese de dejar espacio en torno al mismo para la ventilaci n con el fin de mejorar la disipaci n de calor por lo menos 5 cm detr s y 5 cm en cada lado ADVERTENCIA Las ranuras y aberturas de la caja del aparato sirven para su ventilaci n para poder asegurar un funcionamiento fiable del aparato y para protegerlo contra sobrecalentamiento Para evitar el peligro de incendio las aberturas nunca deber n taparse ni cubrirse con nada como por ejemplo peri dicos manteles cortinas ni ponerse en funcionamiento el aparato sobre una alfombra gruesas o una cama D3 4 2 1 7b_A_Sp Entorno de funcionamiento Temperatura y humedad del entorno de funcionamiento 5 35 C menos del 85 de humedad relativa rejillas de refrigeraci n no obstruidas o instale este aparato en un lugar mal ventilado ni en ugares expuestos a alta humedad o a la luz directa del sol o de otra luz artificial potente D3 4 2 1 7c_A_Sp Si la clavija del cable de alimentaci n de CA de este aparato no se adapta a la toma de corriente de CA que usted desea utilizar deber cambiar la clavija por otra
9. DJ mixer for EFX LINK Can t use the BPM sync function DJ mixer is not connected for EFX LINK A DJ CD player with digital link support is not connected to the DJ mixer The BPM measurement mode is not set to AUTO Connect the DJ CD player and DJ mixer via digital link Set the DJ effector s BPM mode to AUTO Echo sounds are output continuously During echo effect if DEPTH dial is set to MAX and BEAT EFFECTS lever switch is moved from ON to OFF the feedback sound dies not attenuate producing a hold delay effect Rotate DEPTH dial toward the left MIN direction BPM doesn t count tempo in AUTO mode BPM count is strange Input level is too high or too low Some tracks have tempos that prevent them from being measured automatically Automatic measurement range is 70 180 BPM Rotate INPUT LEVEL dial so that the input level meter shows around 0 dB Set to manual mode and input TAP the tempo manually P 18 MIDI sequencer isn t synchronized The MIDI sequencer s sync mode is not set to slave The connected MIDI sequencer is not supported Set MIDI sequencer s sync mode to slave A MIDI sequencer without MIDI timing clock cannot be synchronized e This component may fail to operate properly due effects from static electricity or other causes In this event try disconnecting the power cord and reconnecting it If this doesn t solve the problem
10. Sets jog CHARACTER value Setting range 0 127 Digital jog break MIX General Purpose Controller 8 Bn 53 dd Sets jog MIX value Setting range 0 127 23 lt DRB1369 gt MIDI SETTINGS Program Change MSB LSB ur e SIGNAL FLOW FLOW BEAT2 BEAT1 BEATO JOG2 JOG1 JOGO 0 BEAT EFFECTS gt JOG BREAK 1 JOG BREAK gt BEAT EFFECTS e BEAT EFFECTS e JOG BREAK BEAT2 BEAT1 BEATO JOG2 JOG1 JOGO 0 0 1 DELAY 0 0 1 JET 0 1 0 ECHO 0 1 0 WAH 0 1 1 PITCH ECHO 0 1 1 PHASE SHIFTER 1 0 0 TRANS 1 0 0 RING 1 0 1 FLANGER 1 0 1 ZIP 1 1 0 FILTER 1 1 0 HUMANIZER 1 1 1 PHASER 1 1 1 VOCODER Use general purpose 8 for setting filters About Rhythm Effects Example shown is 3 rhythms During TRANSMIT Each time rhythm TAP is struck data is transmitted in the order rhythm parameter 2 rhythm No and rhythm parameter 1 rhythm time Effector operation RHYTHM MODE button TAP TAP TAP TAP a lt gt lt gt lt gt time 1 time 2 time 3 MIDI data Beat section Rhythm No 1 Rhythm No 2 Rhythm No 3 Rhythm mode time 1 time 2 time 3 During RECEIVE During beat effect if beat operation mode rhythm mode is received the rhythm effect function is enabled Thereafter if the first time rhythm No 1 time 1 rhythm No 2 time 2 rhyth
11. When set to the BEAT gt JOG position signals are processed for beat effects first followed by digital jog break effects Selecting Foot Switch Operation This effector allows connection of an optional foot switch pedal switch for ON OFF control of beat effects and digital jog break effects Use the foot switch to select the way in which the foot switch operates m Set the FOOT SW switch to the desired operating position e When set to the JOG position the foot switch operates to turn digital jog break effects ON OFF e When set to the BOTH position the foot switch operates to turn both digital jog break effects and beat effects ON OFF e When set to the BEAT position the foot switch operates to turn beat effects ON OFF Use a commercially available switching type foot switch with 6 3 mm monaural phone plug Selecting the Level Meter Display This unit s level meter can be set to display the desired mode m Press the METER MODE button to select the desired mode e Each time the METER MODE button is pressed the display switches alternately as follows INPUT and OUTPUT light gt Input and output level are displayed in monaural INPUT and L R light gt Input level is displayed in stereo OUTPUT and L R light Output level is displayed in stereo Digital Link Function Fader Effect Function When the accessory digital link cable is used to connect this unit to a DJ
12. dial while the M button is held down starts memory storage Effects are stored continues for 8 seconds or until the M button is released The SINGLE or LOOP button lights e When an effect has already been stored in memory SINGLE button and LOOP button are lighted if a new effect is stored in memory the previously stored contents will be overwritten and the effect data will be erased 4 Press the SINGLE or LOOP button e When the SINGLE button is pressed the button flashes and the stored effect produced by the jog dial movement is played back one time e When the LOOP button is pressed the button flashes and the stored effect produced by the jog dial movement is played back repeatedly Press the LOOP button once again to stop the effect playback e Jog dial operation stored in memory can be reproduced even when the type of effect is subsequently changed MIDI SETTINGS MIDI SETTINGS MIDI Musical Instrument Digital Interface is a standard protocol designed to allow exchange of information between electronic instruments and or computers A MIDI cable is used to connect two appliances equipped with MIDI connectors thus allowing data to be exchanged between the two appliances The EFX 1000 uses MIDI to send and receive operation and BPM data timing clock Synchronizing an external sequencer to an audio signal or using EFX 1000 operation data to operate an external sequencer To synchronize beat effects
13. position to start operation release it and it returns to the center position OFF position In the center position OFF position the original sound is not affected Press the lever away from you to lock it in position so that the rhythm effect is applied also when the lever is released FECT OUT LEV BPM MODE ORIGINAL EFFECT DEPTH dial Sets the parameter 1 of each effect BPM measurement mode indicators BPM MODE EFFECT TIME Sec mSec AUTO TAP MIDI HAA PITCH ECHO TRANS FLANGER FILTER PHASER H BEAT c EFFECTS LOW MID EFFECT FREQUENCY PERFORMANCE EFFECTOR EFX 1000 MIN MAX CHARACTER ORIGINAL EFFECT BPM MODE button When the BPM MODE button is pressed while in the rhythm mode the mode changes to the beat effect BPM mode MIX dial Adjusts the balance between the original sound and effects CHARACTER dial Sets the parameter 2 of each effect 5 lt DRB1369 gt QUICK OPERATION GUIDE 3 3 EFFECT OUT LEV HHAH A O O
14. to the sound of e For digital connections use RCA pin plug coaxial cables the DJ CD player on channel 2 e Set the IN amp OUT LEVEL switch on the Effector to the 10 dB position INSOUT LEVEL Ge 4 10dB_ 4dB EFX LINK OUT THRU MIDI AUDIO OUT AC IN UTPUT SELECT OUT O gt 7 O olti a 7 co oO DJ CD Player 4 Connecting the power cord e After all other connections are completed insert the CAUTION power cord s plug into a wall power outlet or the Signal inputs are handled in a specific order of auxiliary power outlet of an amplifier priority EFX LINK gt digital inputs gt analog inputs When EFX LINK signals are input digital signals are not output 9 lt DRB1369 gt EFFECTS Beat Effects EFFECTS Beat Effects 1 DELAY effect Adds delay sound to the original sound BPM mode A delay sound is added to the original sound at the value set with the TIME dial e The DEPTH dial can be used to adjust the feedback level Feedback means to input the delay sound back into the delay input This control allows the amount of the feedback to be adjusted near the MAX setting
15. usu rio de la presencia de importantes instruciones sobre el funcionamento y la manutenci n en la libreta que acompa a el aparato D3 4 2 1 1_Sp Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures D8 10 1 2_En CAUTION This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment To prevent electromagnetic interference with electric appliances su
16. you to the ON LOCK position The switch is locked on so that the effect continues to be applied even if you remove your hand from the lever To stop the effect return the lever to the middle position OFF When pulled toward you to the ON position The effect is applied only while the lever is pulled to the ON position when the lever is released it returns automatically to the middle OFF position Use this function when you wish to alternate rapidly between ON and OFF DEPTH dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 1 in response to DEPTH dial rotation see pages 10 11 13 CHARACTER dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 2 in response to CHARACTER dial rotation see pages 10 11 13 MIX dial Use to adjust the mixing balance of original and effect sounds Set to the center indent position for standard effect sounds Operations Beat Effects RHYTHM mode 2 DELAY ECHO PITCH ECHO TRANS FLANGER FILTER PHASER 7 BEAT EFFECTS beat effect select BPM MODE EFFECT TIME o BBB ccc A BBB om RHYTHM TAP_ BPM COUNTER 3 EFFECT FREQUENCY LOW MID HI ge DEPTH MN ax Pronecio TRANS LANGER CHARACTER
17. AP button Only decimal values are shown at this time 18 lt DRB1369 gt 2 Use the beat effect select buttons to select the desired effect e Select from DELAY ECHO PITCH ECHO TRANS FLANGER FILTER or PHASER The selected effect button flashes e See pages 10 11 regarding each effect 3 Use the EFFECT FREQUENCY buttons LOW MID HI to select the band to which the effect is to be applied When a button is pressed the button s indicator will light e Each time a button is pressed it alternates ON OFF 4 Press one beat select button to select the beat with which the effect is to be synchronized Select from 1 8 1 4 1 2 3 4 1 1 2 1 4 1 or 8 1 The selected beat button lights When a beat select button is pressed the corresponding effect time is automatically set Example when BPM is 120 1 1 500 ms 3 4 375 ms 1 2 250 ms When the beat select button is pressed and the TAP button is held down BPM is automatically set from the effect time Manual Input of Effect Time Using the TIME Dial Normally the effect time is automatically set when a beat select button is pressed However the effect time can be set as desired using the TIME dial When the effect time is changed the beat select button lights for the beat automatically set in correspondence to the new effect time y 5 Pull the BEAT EFFECTS lever switch to ON to appy the effect When pushed away from
18. D A converter 96 kHz sampling and 32 bit DSP allowing the addition of effects without lowering the original sound quality a relay bypass function has also been adopted Beat Effector 1 Beat effects BPM mode Equipped with the same automatic BPM counter beat effector made popular by the EFX 500 Allows effect processing on single selected bands in synch with the track tempo BPM for greater expressive possibilities than with conventional all band effecters 2 Beat effects RHYTHM mode This industry first rhythm effector lets you apply effects in synch with the rhythm you input yourself With the expression of a far wider range of unique effects compared to previous beat effectors you have the potential for a new level of DJ performance Break Function The Jog dial allows real time control of effect sounds Up to eight seconds of Jog function can be stored in memory for automated replay Up to 49 effects can be demonstrated in combination with the beat effector MIDHN OUT Function External MIDI signals control signals and timing clock signals can be used to control the effector and as a medium for using the effector to control a sequencer or other component Link Function A variety of functions can be performed by using the dedicated digital link cable to connect this unit to a Pioneer DJ mixer DJM 1000 with digital link support Digit OUT Equipped with digital IN OUT connectors wi
19. No sound or too low Connection cords are loose or aren t con nected properly Connector terminals and plugs are dirty Input level is set too low Effect output level is set too low Connect properly Wipe away dirt and soil Rotate INPUT LEVEL dial toward right MAX direction Try setting IN amp OUT LEVEL switch to the opposite position Rotate EFFECT OUT LEV dial toward right MAX direction Analog inputs aren t output A digital or EFX LINK input is connected When analog and digital inputs are connected simultaneously the digital input is given priority The DJ mixer DJM 1000 connected by EFX LINK has its effecter link set to ON EFX LINK Cancel the EFX LINK and disconnect any digital input with priority over analog inputs The order of priority of inputs is EFX LINK gt Digital input gt Analog input Digital signals aren t output EFX LINK is connected to DJ mixer DJM 1000 via digital link cable The digital output fs setting does not match the connected component If EFX LINK is connected to DJ mixer DJM 1000 via digital link cable ordinary digital signals are not output Disconnect the digital link cable Set the digital output fs to match the connected component When set to BYPASS analog signals aren t output No analog inputs are connected Even if a digital input or EFX LINK is connected analog inputs are output as analog during BYPASS mode Use an
20. Pioneer sound v ision sou DJ EFFECTOR UNIDAD DE EFECTOS PARA DJ DIR as EFX 1000 Operating Instructions Manual de instrucciones EEES IMPORTANT The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance D3 4 2 1 1_En A IMPORTANTE La luz intermitente com el s mbolo de punta ATENCI N de flecha dentro un tri ngulo equil tero Est convenido para avisar el usuario de la presencia de voltaje peligrosa no aislada dentro el producto que podr a constituir un peligro de choque el ctrico para las personas PARA PREVENIR EL PELIGRO DE CHOQUE EL CTRICO NO REMOVER LA TAPA NI LAS PARTES DENTRO NO UTILIZADAS LLAMAR UNA PERSONA CUALIFICADA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN El punto exclamativo dentro un tri ngulo equil tero convenido para avisar el
21. TAL OUT Use to connect the effector to a component provided with coaxial digital input output connectors 7 Foot switch jack FOOT SW Can be connected to a ON OFF type foot switch with 6 3mm phone plug to allow ON OFF control of effects Foot switches are available in several types including press ON press OFF and latching type ON OFF 8 Input output gain select switch IN amp OUT LEVEL Use to select the input output gain 10dB 4dB EFX LINK OUT THRUS MIDI IN OUTPUT INPUT 9 Audio INPUT OUTPUT jacks Uses 6 3mm phones plug For monaural inputs connect L input channel only for output on both L and R channels Audio inputs are throughput output even when the unit s power is turned OFF 10 Audio INPUT OUTPUT jacks INPUT OUTPUT connectors using RCA pin jacks Audio inputs are throughput output even when the unit s power is turned OFF m Before making or changing the connections switch off the power switch and disconnect the power cord from the AC outlet This precaution should also be taken when changing the IN amp OUT LEVEL switch and DIGITAL fs SELECT switch e When connections are made to the phone jack inputs and a monaural signal cable is connected to the L MONO terminal inputs can be made to both the L and R channels e After all other connections are made connect the power cord to a household wall outlet or to the auxiliary AC power takeoff on you
22. TIONS Digital Jog Break 1 JET WAH PHASE SHIFTER RING ZIP HUMANIZER VOCODER Jog effect select 2 DIGITAL JOG BREAK DEPTH oe OE o CHARACTER Jog memory M Jog dial Digital Jog Break Since the digital jog break can continuously change the parameters of each effect generated by rotating the Jog dial the effects can be controlled like a musical instrument Further by using the jog memory function the continuously changing effect sound can be stored in memory and later played back by pressing one of the JOG MEMORY PLAY buttons SINGLE or LOOP 1 Use the Jog effect select buttons to select the desired effect e Select from JET WAH PHASE SHITER RING ZIP HUMANIZER or VOCODER The selected Jog effect button flashes e See page 12 regarding each effect 2 Set the DIGITAL JOG BREAK lever switch to ON and turn the Jog dial DIGITAL JOG BREAK Lever switch operation When pushed away from you to the ON LOCK position The switch is locked on so that the effect continues to be applied even if you remove your hand from the lever To stop the effect return the lever to the middle position OFF When pulled toward you to the ON position The effect is applied only while the lever is pulled to the ON position when the lever is released it returns autom
23. TRANS effect Cuts the original sound intermittently BPM model Cuts the sound at the interval set by the TIME dial cuts latter half of the interval e The DEPTH dial can be used to adjust the amount of shift when the sound is cut TIME el g vz gt Time DEPTH TIME S y gt Time DEPTH TIME A mm e gt Time e The CHARACTER dial can be used to adjust the phase difference between L and R channels TIME CHARACTER t en A A A Q gt Time haa R ch gt Time TIME L ch A Lae gt Time u a R ch NM A gt Time e The MIX dial can be used to adjust the levels of the original and trans sounds EFFECTS Beat Effects RHYTHM mode Cuts the original sound in synch with the TAP rhythm Max 8 TAP 5 The DEPTH dial can be used to adjust the amount of shift when the sound is cut The CHARACTER dial can be used to adjust of phase difference between L and R channels The MIX dial can be used to adjust the levels of the original and trans sounds FLANGER effect By applying a time shifted sound to the original the effect of an ascending or descending jet plane flange effect is produced BPM mode Changes the frequency range to which the flange effect is applied at the interval set by the TIME dial The DEPTH dial can be used to adjust the strength of the flange effect by changing the amount of resonance When approa
24. TRANSMIT or RECEIVE the MIDI indicator flashes and the MIDI setting mode is enabled BEFORE USE CONTROLS AND FUNCTIONS 9 BYPASS button indicator When this button is set to ON the audio input connector signals are fed directly to the output connectors bypassing the effector circuits When the audio input output connectors are connected directly in this way the indicator flashes 10 EFFECT OUT LEV dial When effects are set to ON this dial can be used to control the effect output level Adjustment range is to 6dB Beat Effect section 11 BPM COUNTER display Displays the beats per minute of the input source or the TAP input The indicator flashes during automatic BPM calculation When power is first turned on the counter will flash 120 BPM 12 EFFECT TIME display Displays actual effect time When power is first turned on defaults to 500 mSec 13 BPM measurement mode display AUTO MIDI TAP Displays the BPM measurement mode 14 MIDI display Lights when handling MIDI data 15 RHYTHM TAP display Displays the tap count input in the rhythm mode 16 Beat effect select button indicator DELAY ECHO PITCH ECHO TRANS FLANGER FILTER PHASER Use to select the beat effect All buttons light and selected effect button flashes When power is turned ON DELAY flashes 17 BEAT EFFECTS indicator Lights when beat effects are ON 18 BEAT EFFECTS lever switch OFF ON ON LOCK Pull the lever tow
25. adjusting the beat quarter notes and hitting this key two times or more 4 lt DRB1369 gt EFFECT TIME display BPM measurement mode indicators Adjusting the input level Input signals to the input connectors and adjust the INPUT LEVEL dial INPUT LEVEL MIN MAX Adjusting effect output level Rotate the EFFECT OUT LEV dial to adjust the effect output level EFFECT OUT LEV MIN MAX Changing the level meter display mode Each time the METER MODE button is pressed the level meter display alternates as follows e INPUT OUTPUT light Input and output monaural display e INPUT L R light Input stereo display e OUTPUT L R light Output stereo display METER MODE MIDI SNAP Pioneer O INPUT J L m m m m m m m m o o oo oo os 15 40 7 5 3 2 1 o 1 2 4 7 10 OVER OUTPUT R co m m m m m m m m m m m m m DEPTH dial Sets the parameter 1 of each effect RHYTHM TAP display BPM COUNTER BPM MODE EFFECT TIME AUTO TAP g g g Sec mSec EFFECT FREQUENCY PITCH ECHO TRANS FLANGER PHASER DEPTH MID PERFORMANCE EFFECTOR EFX 1000 ORIGINAL EFFECT MIX dial Adjusts the balance between the original sound and effects CHARACTER dial Sets the parameter 2 of each effect QUICK OPERATION GUIDE 2 3 BYPASS button When the button is pressed butt
26. alog signals for input Or use digital output Outputs when BYPASS is selected are as follows Input connection conditions Analog output Digital output Analog only Analog source Analog source Digital only no output Digital source Analog amp Analog source Digital source digital Effect sounds aren t applied The lever switch is set to OFF MIX dial is set to MIN DEPTH dial is set to MIN EFFECT OUT LEV dial is set to MIN BYPASS button is ON EFFECT FREQUENCY indicators HI MID LOW are all off during use of TRANS FLANGER FILTER or PHASER effects Some combinations of effects may have weak results Particularly some combinations of beat effects and digital jog break may sound weak Either hold lever switch in ON position or set to ON LOCK Rotate MIX dial toward the right MAX direction Rotate DEPTH dial toward the right MAX direction Rotate EFFECT OUT LEV dial toward the right MAX direction If BYPASS indicator is flashed no effects will be output Press BYPASS so that the indicator goes out If EFFECT FREQUENCY indicators are all off only the original sound will be output Press the button corresponding to the frequency band to which you wish to apply effects the button s indicator will light Try setting SIGNAL FLOW switch to the opposite position reverse order of signal processing for beat effects and digi
27. ard you ON to output beat effected sounds In the middle position beat effects are OFF push the lever away from you to lock the lever in the ON LOCK position effects are locked ON When pulled to the ON position beat effects are output only while the lever is held when your finger is released the lever returns to middle OFF position 19 EFFECT FREQUENCY select buttons LOW MID HI Use to select the frequency band of the sounds to which beat effects will be applied The button of the selected band will light When power is first turned ON all three of the ranges LOW MID and HI are selected If all three range buttons are OFF no beat effects will be applied to sounds 20 Beat select buttons indicators 1 8 1 4 1 2 3 4 1 1 2 1 4 1 8 1 During BPM mode When a BPM is measured automatically or input manually the beat select button 1 1 is selected by default The effect is synchronized automatically to the BPM and the corresponding effect time is displayed If a beat select button is then pressed the effect is newly synchronized to the corresponding multiple of the BPM 1 8 1 4 1 2 3 4 etc thus allowing one touch change of the BPM synchronization multiple In turn the selected beat select button lights thus showing to what multiple of the actual BPM the effect is synchronized as well as the multiple of the time parameter During RHYTHM mode When the rhythm input with the TAP button is established
28. as en la parte inferior de la unidad relacionadas con la tensi n nominal etc D3 4 2 2 4_Sp PRECAUCIONES CONCERNIENTES A LA MANIPULACI N DEL CABLE DE ALIMENTACI N Tome el cable de alimentaci n por la clavija No extraiga la clavija tirando del cable Nunca toque el cable de alimentaci n cuando sus manos est n mojadas ya que esto podr a causar cortocircuitos o descargas el ctricas No coloque la unidad alg n mueble etc sobre el cable de alimentaci n Aseg rese de no hacer nudos en el cable ni de unirlo a otros cables Los cables de alimentaci n deber n ser dispuestos de tal forma que la probabilidad de que sean pisados sea m nima Una cable de alimentaci n da ado podr causar incendios o descargas el ctricas Revise el cable de alimentaci n est da ado solicite el reemplazo del mismo al centro de servicio autorizado PIONEER m s cercano o a su distribuidor s002_Sp Thank you for buying this Pioneer product Please read through these operating instructions so you will know how to operate your model properly After you have finished reading the instructions put them away in a safe place for future reference In some countries or regions the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings However the method of connecting and operating the unit is the same K015 En FEATURES The high fidelity design features a 24 bit A D and
29. atically to the middle OFF position Use this function when you wish to alternate rapidly between ON and OFF e Parameter changes caused by rotating the Jog dial are indicated on the DIGITAL JOG BREAK METER DEPTH dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 1 in response to DEPTH dial rotation see pages 12 13 CHARACTER dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 2 in response to CHARACTER dial rotation see pages 12 13 20 lt DRB1369 gt MIX dial Use to adjust the mixing balance of original and effect sounds Set to the center indent position for standard effect sounds HOLD Function When the HOLD button is pressed and lit the effect generated by the rotation of the Jog dial continues when the dial rotation stops Jog Memory Up to 8 seconds of the digital jog break s jog dial movement can be stored in memory and the effect later played back at a single touch 1 Use the Jog effect select buttons to select the desired effect e Select from JET WAH PHASE SHITER RING ZIP HUMANIZER or VOCODER e The selected Jog effect button flashes e See page 12 regarding each effect 2 Set the DIGITAL JOG BREAK lever switch to ON to monitor the effect 3 Turn the Jog dial while holding down the Jog memory button M Turning the Jog
30. b frequency range ON 1 BitO LOW Bit1 MID Bit2 HI MSB LSB ojojojojfojHimojow Rhythm TAP rhythm time General Purpose Controller 2 Bn 11 MSB Bn 31 LSB Sets tap time interval for rhythm effect Setting range unit mSec 1 2000 Rhythm TAP rhythm no soft pedal Bn 43 dd Sets tap number for rhythm effect Setting range 1 8 BPM mode SW Rhythm mode SW Rhythm REC hold 2 Bn 45 dd Changes Beat operating mode 1 BPM mode 2 Rhythm mode During rhythm mode if rhythm mode is set again the recorded rhythm effect will be canceled and new rhythm data can be input Jog operation Jog dial General Purpose Controller 1 Bn 10 MSB Bn 30 LSB Sets jog dial movement Setting range 0 2160 Jog center position is considered 1080 when dial is rotated clockwise changes to maximum 2160 when dial is rotated counterclockwise changes to minimum 0 Beat volume Beat effect DEPTH Effect 1 Depth Bn 5B dd Sets beat DEPTH value Setting range 0 127 Beat effect CHARACTER General Purpose Controller 5 Bn 50 dd Sets beat CHARACTER value Setting range 0 127 Beat effect MIX General Purpose Controller 6 Bn 51 dd Sets beat MIX value Setting range 0 127 Jog volume Digital jog break DEPTH Effect 2 Depth Bn 5C dd Sets Jog DEPTH value Setting range 0 127 Digital jog break CHARACTER General Purpose Controller 7 Bn 52 dd
31. can be used to adjust the levels of the ring reverb and original sounds 5 ZIP effect The Jog dial is used to change the pitch Up about 1 octave t Original Q 4 5 Pitch sound Down 4 j 5 about 15 octaves REV ES FWD Jog dial e The DEPTH dial can be used to adjust the Jog dial s variable range step DEPTH DEPTH TA FWD REV ED Jog dial e The CHARACTER dial can be used to adjust the reverb effect e The MIX dial can be used to adjust the levels of the zip reverb and original sounds 6 HUMANIZER effect The original sound is modified to resemble the vowel sounds of the human voice e The Jog dial is used to vary the vowel sound coloration i e a o u REV ED FWD Jog dial e The DEPTH dial is used to change the unique coloring of vowel sounds by adjusting the amount of resonance When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to adjust the reverb effect e The MIX dial can be used to adjust the levels of the humanizer reverb and the original sounds 7 VOCODER effect The input sound is replaced by an inter nally generated signal sound producing a mechanical sound effect e The Jog dial is used to change the frequency of the internally generated signal sound e The DEPTH dial can be used to vary the internally generated sound from the basic soun
32. ch as radios and televisions use shielded cables and connectors for connections D8 10 3a_En Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user s right to operate the equipment D8 10 2_En WARNING This equipment is not waterproof To prevent a fire or shock hazard do not place any container filed with liquid near this equipment such as a vase or flower pot or expose it to dripping splashing rain or moisture D3 4 2 1 3_A_En WARNING Before plugging in for the first time read the following section carefully The voltage of the available power supply differs according to country or region Be sure that the power supply voltage of the area where this unit will be used meets the required voltage e g 230V or 120V written on the rear panel D3 4 2 1 4_A En VENTILATION CAUTION When installing this unit make sure to leave space around the unit for ventilation to improve heat radiation at least 5 cm at rear and 5 cm at each side WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating To prevent fire hazard the openings should never be blocked or covered with items such as newspapers table cloths curtains or by operating the equipment on thick carpet or a bed D3 4 2 1 7b_A_En WARNING To prevent a fire hazard do not place any nake
33. ching the MAX setting the level of the sound increases The CHARACTER dial can be used to adjust the cyclic changes in the flange effect The MIX dial can be used to adjust the levels of the original and flanger sounds TIME CHARACTER a ot Flange effect change gt Time TIME CHARACTER Flange effect change gt Time TIME CHARACTER n a ax Flange effect change Time RHYTHM mode Changes the frequency subjected to flange effect in synch with the TAP rhythm The DEPTH dial can be used to adjust the strength of the flange effect by changing the amount of resonance When approaching the MAX setting the level of the sound increases The CHARACTER dial can be used to adjust the cyclic changes in the flange effect The MIX dial can be used to adjust the levels of the original and flanger sounds 6 FILTER effect A low pass filter is applied to the original sound to produce more muted sound BPM mode The cutoff frequency of the low pass filter changes with the cycle set by the TIME dial e The DEPTH dial is used to change the unique coloring of the sound by adjusting the amount of resonance When approaching the MAX setting the level of the sound increases ei a 7 A e The CHARACTER dial can be used to vary the cutoff frequency of the cyclic low pass filter CHARACTER 4 UV Got Sal mit PPP PP AR gt CHARACTER Amann a PPT
34. d flame sources such as a lighted candle on the equipment D3 4 2 1 7a_A_En Operating Environment Operating environment temperature and humidity 5 C 35 C 41 F 95 F less than 85 RH cooling vents not blocked Do not install this unit in a poorly ventilated area or in locations exposed to high humidity or direct sunlight or strong artificial light D3 4 2 1 7c_A_En 2 lt DRB1369 gt Ifthe AC plug of this unit does not match the AC outlet you want to use the plug must be removed and appropriate one fitted Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel If connected to an AC outlet the cut off plug can cause severe electrical shock Make sure it is properly disposed of after removal The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time for example when on vacation D3 4 2 2 1a_A_En CAUTION The POWER switch on this unit will not completely shut off all power from the AC outlet Since the power cord serves as the main disconnect device for the unit you will need to unplug it from the AC outlet to shut down all power Therefore make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident To avoid fire hazard the power cord should also be unplugged from the AC out
35. d to a chord The sound more nearly approximates the chord as the adjustment approaches the MAX setting e The CHARACTER dial can be used to change chords codes Selectable codes include Minor MIN Minor7 7 Major center position Major7 Sus4 and Add9 MAX block e The MIX dial can be used to adjust the levels ofthe vocoder and original sounds EFFECTS Effect Parameters Effect Parameters Beat effect Parameter 0 TIME Parameter 1 DEPTH Parameter 2 CHARACTER Parameter 3 MIX Comments BPM MODE RHYTHM MODE 1 16000 ms 1 16000 ms Feedback feedback level TAP gain TAP delay level Feedback filter Amount of feedback filter TAP filter Amount of TAP delay filter Max 8 TAP BPM MODE RHYTHM MODE 1 16000 ms 1 16000 ms Feedback feedback level TAP gain TAP delay level Feedback filter Amount of feedback filter TAP filter Amount of TAP delay filter BPM MODE RHYTHM MODE 1 16000 ms 1 16000 ms Feedback feedback level TAP delay level Pitch delay sound pitch TAP Pitch TAP delay sound pitch BPM MODE RHYTHM MODE 10 16000 ms 10 16000 ms Shape cut shift cut shift Phase L R ch phase difference L R ch phase difference BPM MODE FLANGER RHYTHM MODE 10 32000 ms 10 32000 ms Resonance Resonance LFO pattern change cycl
36. ge 13 33 Jog dial Effect parameters change in response to the rotation of the dial 34 Jog memory button M If the Jog dial is rotated while holding this button depressed the parameter change in response to the movement is recorded to memory to a maximum 8 seconds Recording to memory is not possible during jog memory play 35 Jog memory SINGLE play button indicator If the button is pressed while the button indicator is lighted the parameter change previously recorded in memory in response to the Jog dial movement is reproduced played back one time only Indicator lights when the jog operation is stored in memory Indicator flashes during jog memory single play playback 16 lt DRB1369 gt 36 Jog memory LOOP play button indicator If the button is pressed while the button indicator is lighted the parameter change previously recorded in memory in response to the Jog dial movement is reproduced played back repeatedly Press again to end Jog memory loop play Indicator lights when the jog operation is stored in memory Indicator flashes during jog memory loop play playback 37 Jog HOLD button indicator When this button is pressed so that its indicator lights the effect produced when rotating the Jog dial is maintained even if you remove your hand from the dial when the hold function is OFF the effect returns to normal if your hand is removed from the dial When power is first turned on the button defa
37. ic effect LFO pattern change cyclic effect BPM MODE FILTER RHYTHM MODE 10 32000 ms 10 32000 ms Resonance Resonance LFO pattern change cyclic effect LFO pattern change cyclic effect BPM MODE PHASER RHYTHM MODE Digital Jog Break 10 32000 ms 10 32000 ms Resonance Resonance LFO pattern change cyclic effect LFO pattern change cyclic effect Max 8 TAP The effect time display in the rhythm mode shows the total time from the beginning to end of TAP input For this reason the noted MIN time may be somewhat different from the effect time display Parameter 0 JOG Parameter 1 DEPTH Parameter 2 CHARACTER Parameter 3 MIX Comments JET Delay time amount of delay Resonance Reverb reverberation effect MIX WAH Frequency filter frequency Resonance Reverb reverberation effect MIX PHASE SHIFTER Frequency filter coefficient Resonance Reverb reverberation effect MIX RING Frequency sine wave frequency Amplitude sine wave amplitude Reverb reverberation effect MIX ZIP Pitch Scale Step Scale Linear Reverb reverberation effect MIX HUMANIZER Vowel vowel sound Resonance Reverb reverberation effect MIX VOCODER Oscillator frequency internally generated sound frequency Chord MIX chord MIX rati
38. is moved from ON to OFF a hold delay effect will be produced without attenuating the feedback sound near the MAX setting the sound level rises In the RHYTHM mode when the switch is turned OFF the effect will end with the final TAP delay sound for the original sound BPM mode TAP 8 echo block 3 PITCH ECHO effect Changes the pitch of the delay sound and applies the effect to the original sound In the same way as for the ECHO effect the effect sound is maintained even if the BEAT EFFECTS lever switch is set from ON to OFF BPM mode Changes the pitch of the delay sound set with the TIME dial and applies the effect to the original sound e The DEPTH dial can be used to adjust the feedback level e The CHARACTER dial can be used to adjust the pitch of the delay sound e The MIX dial can be used to adjust the levels of the original and pitch echo sounds Pitch echo block RHYTHM model Changes the pitch of the TAP delay sound and applies the effect to the original sound Max 4 TAP e The DEPTH dial can be used to adjust the TAP delay level near the MAX setting the sound volume will rise somewhat e The CHARACTER dial can be used to adjust the pitch of the TAP delay sound e The MIX dial can be used to adjust the levels of the original and pitch echo sounds TAP 1 pitch echo block TAP 2 pitch echo block TAP 3 pitch echo block TAP 4 pitch echo block 4
39. ith the Jog dial will be stored in memory maximum 8 seconds When storage is completed the SINGLE and LOOP buttons light A 2 Press the SINGLE button or LOOP button e When the SINGLE button is pressed the stored Jog dial effect change will be replayed one time only e When the LOOP button is pressed the stored Jog dial effect change will be replayed repeatedly Press the button once more to stop the effect BEFORE USE CONNECTIONS CONNECTIONS Connection Panel 1 Power input socket AC IN Use the provided power cord to connect this socket to an AC outlet 2 POWER switch 3 Digital OUTPUT fs SELSECT switch Use to change the digital output frequency sampling rate fs 44 1kHz 48kHz 96kHz 4 Link input output connector EFX LINK When the accessory digital link cable is used to connect this connector to the DJ mixer DJM 1000 with digital link support digital link functions can be used permitting a variety of new functions CAUTION The EFX LINK connector is designed to be connected via the provided digital link cable ONLY to a component equipped with the designated digital link function The unit may be damaged if this connector is mistakenly connected to any other component 5 MIDI input output connectors MIDI OUT THRU MIDI IN Use to connect the effector to a MIDI component see page 21 6 Digital input output connectors DIGITAL IN DIGI
40. ith the TAP rhythm e The DEPTH dial can be used to adjust the strength of the phase effect by changing the amount of resonance When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to adjust the cyclic changes in the phase effect e The MIX dial can be used to adjust the levels of the original and phaser sounds 11 lt DRB1369 gt EFFECTS Digital Jog Break Digital Jog Break 1 JET effect A time shifted sound is applied to the original thus producing the effect of a jet airplane ascending or descending flange effect e The Jog dial is used to change the frequency range that is affected by the flange effect ee ee Flange effect change REV lt ED Jog dial gt FWD e The amount of resonance is changed using the DEPTH dial to emphasize the flange effect When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to adjust the reverb effect Jet block e The MIX dial can be used to adjust the levels of the jet reverb sound and original sound 2 WAH effect The filter s cutoff frequency is shifted causing great change in the sound tone e The Jog dial is used to vary the filter s cutoff frequency E 3 E gt Frequency Jog dial ED o AAA AAA 5 5 5 gt Frequency Jog dial ES e The DEPTH dial is used to change the unique co
41. let when left unused for a long period of time for example when on vacation D3 4 2 2 2a_A_En When using this product follow the instructions written on the underside of the unit which D3 4 2 2 4_En concern rated voltage etc POWER CORD CAUTION Handle the power cord by the plug Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock Do not place the unit a piece of furniture etc on the power cord or pinch the cord Never make a knot in the cord or tie it with other cords The power cords should be routed such that they are not likely to be stepped on A damaged power cord can cause a fire or give you an electrical shock Check the power cord once in a while When you find it damaged ask your nearest PIONEER authorized service center or your dealer for a replacement ADVERTENCIA Este aparato no es impermeable Para evitar el riesgo de incendio y de descargas el ctricas no ponga ning n recipiente lleno de l quido como pueda ser un vaso o un florero cerca del aparato ni lo exponga a goteo salpicaduras lluvia o humedad 002_En D3 4 2 1 3_A_Sp ADVERTENCIA Antes de enchufar el aparato a la corriente lea la secci n siguiente con mucha atenci n La tensi n de la red el ctrica es distinta seg n el pa s o regi n Aseg rese de que la tensi n de la alimentaci n de la localidad donde se proponga
42. live performance 1 Press the BPM MODE button to select the BPM beats per minute measurement mode AUTO BPM is measured automatically from the input music source MIDI BPM is measured automatically based on the MIDI timing clock TAP BPM is input manually by tapping on the TAP button When power is first turned ON the mode defaults to AUTO e The selected mode is shown by the BPM mode indicator In the event the input signal cannot be counted properly the BPM COUNTER flashes The measurement range in the AUTO mode is 70 180 BPM Correct measurement may not be possible depending on the music track in this event input the tempo manually using the TAP mode gt Manual BPM input using the TAP button When the TAP button is tapped two or more times in time with the beat quarter notes the average value of the intervals is used to set BPM When BPM is set to AUTO or MIDI mode pressing the TAP button changes the BPM measuring mode to the TAP mode and the unit measures the intervals at which the TAP button is struck When BPM is set with the TAP button the beat select button 1 1 is selected and the time of 1 beat quarter notes is set to the effect time Xx gt Manual BPM input using the TIME dial BPM can be directly set by turning the TIME dial when the TAP button is held down e BPM can be setin 0 1 increments by pressing the BPM MODE button and turning the TIME dial while holding down the T
43. loring of the sound by adjusting the amount of resonance When approaching the MAX setting the level of the sound increases DEPTH A Frequency DEPTH Frequency DEPTH Cl oT MAX Frequency e The CHARACTER dial can be used to adjust the reverb effect j Reverb e The MIX dial can be used to adjust the levels of the wah reverb sound and the original sound 12 lt DRB1369 gt 3 PHASE SHIFTER effect A phase shifted sound is added to the original thus producing a phase shifter effect e The Jog dial is used to change the frequency range that is affected by the phase effect 7 Phase effect change REV lt ES Jog dial gt FWD e The amount of resonance is changed using the DEPTH dial to emphasize the phase effect When approaching the MAX setting the level of the sound increases e The CHARACTER dial can be used to adjust the reverb effect e The MIX dial can be used to adjust the levels of the phase shifter reverb sound and the original sound 4 RING modulator effect By modulating the original sound in the shape of a sine wave the resulting sound coloration resembles a ringing bell e The Jog dial is used to vary the sine wave frequency EN GOON REV ED Jog dial FWD e The DEPTH dial can be used to adjust the amplitude of the sine wave e The CHARACTER dial can be used to adjust the reverb effect Ring block o e The MIX dial
44. m No 3 time 3 are transmitted in that order the effector continues to operate in response to the received rhythm During rhythm effect if the beat operation mode BPM mode is transmitted the function returns to beat effect Snapshot METER MODE MIDI SNAP INPUT LEVEL SIGNAL FLOW FOOT SW MIDI Once the effector is set to a target value a snapshot of that manni aero mone state can be taken When snapshot is used all commands som El recae mase for control change are transmitted at once D When setting TRANSMIT hold the METER MODE MIDI SNAP button depressed to transmit the snapshot When this is done the MIDI indicator will flash JOG gt BEAT JOG Pr INPUT OUTPUT R gag MIN MAX BEAT gt JOG BEAT OFF 24 lt DRB1369 gt OTHER TROUBLESHOOTING TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions If you think there is something wrong with this component check the points below Sometimes the trouble may originate from another component Thus also check the other electrical appliances also in use If the trouble cannot be rectified even after checking the following items contact your dealer or nearest PIONEER service center Symptom Probably cause Remedy No power Power cord isn t connected Connect power cord to outlet
45. mixer DJM 1000 with digital link support send return connections are completed by a single digital connection thus enabling fader effect functions that allow the DJ mixer s fader to be used to perform digital jog break Bypass Function This function allows signals to be output directly without passing through the effects processing circuitry m Press the BYPASS button to make a direct link between input and output e When the BYPASS button is pressed the button flashes and input signals are output directly without passing through the effector circuitry e When the BYPASS button is flashed the unit s controls will have no effect on the input signals 17 lt DRB1369 gt OPERATIONS Beat Effects BPM mode 2 DELAY ECHO PITCH ECHO TRANS FLANGER FILTER PHASER 5 BEAT EFFECTS beat effect select BPM MODE EFFECT TIME Sno AABE sce A AEE om low ECHO RHYTHM TAP_ BPM COUNTER 3 EFFECT FREQUENCY E LOW MID HI za DEPTH MN max CHARACTER a CHARACTER gq MIX ORIGINAL EFFECT TIME 1 BPMMODE TAP 4 1 8 1 4 1 2 3 4 1 1 2 1 4 1 8 1 beat select Beat Effects BPM mode Since the beat effect time of the beat effect BPM mode can be synchronized in real time with the BPM beats per minute you can easily generate effects in time with the rhythm of a
46. n Clears the currently input rhythm and allows input of a new rhythm 15 lt DRB1369 gt BEFORE USE CONTROLS AND FUNCTIONS 26 RHYTHM MODE button indicator When this button is pressed the RHYTHM mode is selected and the button lights 27 Beat effect DEPTH dial Allows adjustment of effect feedback and timing parameters in accordance with the amount of rotation see page 13 28 Beat effect CHARACTER dial Allows adjustment of parameters other than those set with the beat effect DEPTH dial see page 13 29 Beat effect MIX dial Rotate to adjust the mixing balance of original and effect sounds When rotated fully to the ORIGINAL side the original un effected sound will be output as the dial is rotated toward the EFFECT side the effect sound is amplified and the original sound decreases Digital Jog Break section 30 Digital jog break effect MIX dial Rotate to adjust the mixing balance of original and effect sounds When rotated fully to the ORIGINAL side the original un effected sound will be output as the dial is rotated toward the EFFECT side the effect sound is amplified and the original sound decreases 31 Digital jog break effect CHARACTER dial Allows adjustment of parameters other than those set with the digital jog break DEPTH dial see page 13 32 Digital jog break DEPTH dial Allows adjustment of effect feedback and timing parameters in accordance with the amount of rotation see pa
47. n to confirm NOTE If the MIDI sequencer s BPM is set in 0 1 units it may not match the BPM display on the EFX 1000 21 lt DRB1369 gt MIDI SETTINGS MIDI Implementation Chart Function Transmit Receive Comments Basic channel When power ON 1 16 Settable range 1 16 1 16 1 16 Stored in memory When power ON Mode 3 Message x Replacement Mode Mode 3 x Note number Sound range Note ON Note OFF Velocity After touch By Key By Channel Pitch Bender 12 44 13 45 16 48 17 49 64 66 Control change 67 69 80 81 82 83 91 92 Beat select time parameter MSB LSB Time parameter MSB LSB JOG parameter MSB LSB Rhythm parameter 1 MSB LSB Effect ON OFF Frequency select Rhythm parameter 2 Beat Operation Mode VR parameter 1 VR parameter 2 VR parameter 3 VR parameter 4 VR parameter 5 VR parameter 6 Program change setting range Exclusive Song position Song select Tune Common Clock Command Real time Transmit start stop Local ON OFF All Note OFF Active sensing Reset XXXX OO XX X X O 00000000000000 X XX x X X X XXXX XO XXX X O 00000000000000 X XX x XIX X Comments Mode 1 Omni ON Poly Mode 2 Omni ON Mono O Yes Mode 3 Omni OFF Poly Mode 4 Omni OFF Mono X No Control Change CC Table Function EFX 1000 Operation Mes
48. ndition hold the MIDI START CH SET button depressed e The MIDI indicator will flash and the setting mode will be enabled 3 Rotate the TIME dial to select MIDI channel 4 Press the MIDI START CH SET button e The MIDI channel will be recorded and the unit will leave the setting mode NOTE It may not be possible to set BPM correctly with some tracks 1 Use a commercially available MIDI cable to connect the MIDI sequencer s MIDI OUT connector to the EFX 1000 s MIDI IN connector e Adjust controls for optimum instrument input output levels e Setall effect switches to OFF e Set BYPASS switch to OFF 2 Set the MIDI switch to the RECEIVE position e The MIDI OUT THRU connector will throughput output the same signal that was input 3 Start the MIDI sequencer e Even during use of sequencer control the EFX 1000 can be controlled directly if desired but depending on the volume the set parameter values may jump at the instant an operation is performed so caution is needed e The range that the MIDI timing clock can accept is 40 250 BPM Setting the RECEIVE MIDI channel The RECEIVE channel can be set and recorded in memory separately from the TRANSMIT channel 1 Set MIDI switch to RECEIVE position 2 In this condition hold the MIDI START CH SET button depressed e The MIDI indicator will flash and the setting mode will be enabled 3 Rotate the TIME dial to select the MIDI channel then press the TAP butto
49. ns Before making or changing the connections switch off the power switch and disconnect the power cord from the AC outlet 1 Connecting the SEND RETURN Terminals on the e Ifthe DJ mixer supports digital link it can be connected DJ Mixer on DJ mixer provided with SEND and to the EFX LINK connector using the provided digital link RETURN terminals cable to eliminate the need for connection by an analog e Make connections using cables with 1 4 inch 6 3 mm in 6 3mm phone plug cable audio signals transmitted over diameter phone plugs the digital link cable are in digital format e Set the DJ mixer so that the SEND and RETURN terminals can be used e Set the IN amp OUT LEVEL switch on the Effector to the 10 dB position INSOUT Ge Effector EFX 1000 naout S27 008 sas oF FOOT SW FOOT SW k an eo gt Ya aan a a ay Accessory digital link cable CELLET Foot switch pedal switch Y 4 gt r s EFX LINK e a a a NENA Signal flow RETURN
50. o Chord 13 lt DRB1369 gt BEFORE USE CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS Control Panel a E INPUT LEVEL SIGNAL FLOW FOOT SW MIDI JOG gt BEAT JOG TRANSMIT METER MODE c MDISNAP MIDI EFFECT OUT LEV y i 5 som nor O CN Ned 1 145 0 7 5 3 2 alo MIN MAX BEAT gt JOG Data START cHser BYPASS Se MIN MAX DIGITAL JOG BREAK METER BPM MODE EFFECT TIME 113 AUTO TAP g g A A Sec MIDI 1 mSec PERFORMANCE EFFECTOR EFX 1000 1 INPUT LEVEL dial Use to adjust the input level Adjustment range is o to 9dB with analog inputs and to OdB with digital inputs 2 SIGNAL FLOW switch Use to select the order of signal flow between beat effect and digital jog break sections JOG gt BEAT Signals travel through the digital jog break section before passing to the beat effect section BEAT gt JOG Signals travel through the beat effect section before passing to the digital jog break section 3 Foot switch mode selector FOOT SW Use to select which function is controlled ON OFF by an attached foot switch pedal switch BEAT Attached foot switch contr
51. ococccccccncnnnnonennnnnnnnnnnnnancnnnnnnnnnns 17 Beat Effects BPM mode cccssceeeeeeteeeeeees 18 Beat Effects RYHTHM mode nsss 19 Digital Jog Break oomoococoncoconannonancanannnnnracannansonanas 20 JOY MOMOTY 0 cecceseetenesseeeeeseeeesesenersesereseeseeseassoees 20 MIDI SETTINGS MIDI SETTINGS cuina nica iaa 21 Synchronizing an external sequencer to an audio signal or using EFX 1000 operation data to operate an external sequencer 21 To synchronize beat effects to external sequencer or use an external sequencer to operate the EFX 1000 cocococcccccccnonocccnccnnconanananncnnnos 21 MIDI Implementation Chart ooococccnoccccnncnacncnnnnanns 22 Control Change CC Table oocconncccccnnoccccnnanancnnns 22 Program Change cooccccncccconcconnnncnncnnancnnnnnnnancnnnnnanns 24 About Rhythm Effects cooooccccnnccccconacccnnnnnancnnnannnos 24 Snapshot esei ara pra intra 24 OTHER TROUBLESHOOTING cscccesessseceseeesseesseeesseeeeeees 25 SPECIFICATIONS csscccseecsseecsseeeseessneesseresseeeeseeeses 26 BLOCK DIAGRAM ccccsssecestecsseeeseesseeeseeesseeeeseeeeees 80 CONFIRM ACCESSORIES Operating InstructiONS cece eeeeeeeeeeseeeeeeeeeneeeeeeeeeeeeeeeeeeeee 1 Digital hink eaple cosida 1 Power GONG vincia loas 1 3 lt DRB1369 gt QUICK OPERATION GUIDE 1 3 EFFECT OUT LEV BPMMODE LLE E SeESSS
52. ols beat effect function ON OFF JOG Attached foot switch controls digital jog break function ON OFF BOTH Attached foot switch controls both beat effect function and digital jog break function ON OFF 4 MIDI mode select switch Select MIDI communication between computer and other instruments etc TRANSMIT Acts as MIDI controller RECEIVE Effector can be controlled by MIDI signals OFF Acts as effector communication OFF 14 lt DRB1369 gt 5 METER MODE MIDI SNAP button Use to switch the function of the level meter display Each time the button is pressed the level meter display switches between input and output monaural display input stereo display and output stereo display MIDI Snapshot Mode When this button is held depressed with the MIDI mode set to TRANSMIT a snapshot will be sent to the external MIDI component 6 Level meter mode display INPUT OUTPUT L R Input and output monaural display Both INPUT and OUTPUT indicators light Input stereo display INPUT and L R indicators light Output stereo display OUTPUT and L R indicators light 7 Level meter display 8 MIDI START CH SET button indicator MIDI START If this button is pressed when MIDI mode is set to TRANSMIT the MIDI start stop signal is output Lights steadily with START and goes out with STOP MIDI channel setting CH SET If this button is held depressed when MIDI mode is set to
53. on indicator flashes the signal entering the input connectors is output spass directly without modification to the output connectors SIGNAL FLOW switch SIGNAL FLOW Selects the order in which signals 4 are passed through the electronic tt sections from beat effect to digital jog break or vice versa BEAT gt JOG USING BEAT EFFECTS RHYTHM MODE 1 Select the rhythm input mode Press the RHYTHM MODE button so that the button indicator lights 2 Select effect type Press the DELAY ECHO PITCH ECHO TRANS FLANGER FILTER or PHASER button and the pressed button starts to flash 3 Select the sound range for the effect Press the button of the frequency LOW MID HI you wish to affect by the rhythm effect and the corresponding indicator lights 4 Set to REC mode When the REC button is pressed the BPM display indicates r g e If no rhythm has been input the unit will automatically enter the REC mode in step 1 5 Input the rhythm Tap your finger on the TAP button to input the desired rhythm As you input the rhythm the rhythm will be calculated and displayed on the RHYTHM TAP display up to 8 taps with tap interval of 2 seconds or less 6 Select the overall rhythm time The pressed beat select button will light and the overall rhythm time will be set at the multiple corresponding to the pressed button 7 Apply an effect Press the lever towards you ON
54. or the input rhythm will be multiplied in response to the selected button e Select from 1 8 1 4 1 2 3 4 1 1 2 1 4 1 or 8 1 The selected beat button lights 7 Pull the BEAT EFFECTS lever switch to ON to appy the effect When pushed away from you to the ON LOCK position The switch is locked on so that the effect continues to be applied even if you remove your hand from the lever To stop the effect return the lever to the middle position OFF When pulled toward you to the ON position The effect is applied only while the lever is pulled to the ON position when the lever is released it returns automatically to the middle OFF position Use this function when you wish to alternate rapidly between ON and OFF e If the Rhythm REC button is pressed during the rhythm mode the input rhythm will be cleared and rhythm input mode is once again enabled DEPTH dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 1 in response to DEPTH dial rotation see pages 10 11 13 CHARACTER dial Set to the center center indent position for standard effect sounds For more information regarding the change in parameter 2 in response to CHARACTER dial rotation see pages 10 11 13 MIX dial Use to adjust the mixing balance of original and effect sounds Set to the center indent position for standard effect sounds 19 lt DRB1369 gt OPERA
55. que se adapte apropiadamente El reemplazo y montaje de una clavija del cable de alimentaci n de CA s lo deber realizarlos personal de servicio t cnico cualificado Si se enchufa la clavija cortada a una toma de corriente de CA puede causar fuertes descargas el ctricas Aseg rese de que se tira de la forma apropiada despu s de haberla extra do El aparato deber desconectarse desenchufando la clavija de la alimentaci n de la toma de corriente cuando no se proponga utilizarlo durante mucho tiempo por ejemplo antes de irse de vacaciones D3 4 2 2 1a_A_Sp PRECAUCI N El interruptor de la alimentaci n POWER de este aparato no corta por completo toda la alimentaci n de la toma de corriente de CA Puesto que el cable de alimentaci n hace las funciones de dispositivo de desconexi n de la corriente para el aparato para desconectar toda la alimentaci n del aparato deber desenchufar el cable de la toma de corriente de CA Por lo tanto aseg rese de instalar el aparato de modo que el cable de alimentaci n pueda desenchufarse con facilidad de la toma de corriente de CA en caso de un accidente Para evitar correr el peligro de incendio el cable de alimentaci n tambi n deber desenchufarse de la toma de corriente de CA cuando no se tenga la intenci n de utilizarlo durante mucho tiempo seguido por ejemplo antes de irse de vacaciones D3 4 2 2 2a A Sp Cuando emplee este producto siga las instrucciones escrit
56. r amplifier See page 21 for instructions on how to use the MIDI terminals CAUTION Do not make any connections that may create signal loops as this will cause circuit oscillations which could damage the speakers Example of connections that must not be performed e Do not connect the output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the same mixer e Do not connect the SEND output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the DJ Mixer except for the RETURN terminal Installation Location e Avoid mounting on top of amplifiers near spotlights or other heat emitting components and appliances extended exposure to heat can cause damage to the effector itself e Install this unit as far as possible away from tuners and TV sets A unit installed in close proximity to such equipment may cause noise or degradation of the picture Cleaning the unit To clean the unit wipe with a polishing or a soft dry cloth For stubborn dirt moisten a soft cloth with a weak solution of neutral detergent diluted in five to six parts water wring the cloth well and wipe away the dirt Use a dry cloth to wipe the surface dry Do not use volatile liquids such as benzene or thinner which will damage to the unit 7 lt DRB1369 gt BEFORE USE CONNECTIONS Basic Connectio
57. sage Format Hex Comments Command Signal flow change Effect type Beat effect select ProgramChange Cn pc See program change below switching Digital jog break Effect select Sets effect ON OFF Beat effect ON OFF b Effect ON OFF ON 1 Bit0 JOG Effect ON OFF Peete Hold 1 Bn 40 0b Bit BEAT Digital jog break Effect ON OFF MSB LSB o o Jo o 0 o pear Jos 22 lt DRB1369 gt MIDI SETTINGS Function EFX 1000 Operation Message Command Format Hex Comments Effect time Operation Beat select Effect Control 1 Bn 0c MSB Bn 2c LSB Sets effect time Setting range unit mSec DELAY ECHO PITCH ECHO 1 16000 TRANS 10 16000 FLANGER FILTER PHASER 5 16000 When 5 16000 are transmitted for FLANGER FILTER or PHASER EFX 1000 internally multiplies value by x2 so as to operate at 10 32000 On receive side search is performed for beginning of effect cycle TIME dial Effect Control 2 Bn 0d MSB Bn 2d LSB Sets effect time Setting range unit mSec DELAY ECHO PITCH ECHO 1 16000 TRANS 10 16000 FLANGER FILTER PHASER 5 16000 When 5 16000 are transmitted for FLANGER FILTER or PHASER EFX 1000 internally multiplies value by x2 so as to operate at 10 32000 On receive side search is not performed for beginning of effect cycle Beat operation Effect frequency select sostenuto Bn 42 Ob Sets frequency range subjected to effect
58. t JOG BEAT OFF MIN MAX SIGNAL FLOW METER MODE BYPASS Adjusting Input Level Adjust the input level so that the sound is not distorted due to an excessive input level E Input signals to the input connectors and rotate the INPUT LEVEL dial to adjust the level e Use the METER MODE button to select input stereo display INPUT L R indicators light e l the proper adjustment cannot be obtained without rotating the INPUT LEVEL dial to its extreme MIN or MAX positions try changing the position of the rear panel IN amp OUT LEVEL switch 10dB 4dB Adjusting Effect Output Level Adjusts the sound level of the effect applied to the input sound signal by the beat effect and the digital jog break E Input signals to the input connectors and rotate the EFFECT OUT LEV dial to adjust the effect output level e Use the METER MODE button to select output stereo display OUTPUT L R indicators light When both the BEAT EFFECTS lever switch and the DIGITAL JOG BREAK lever switch are set to OFF the output level is not changed by turning the EFFECT OUT LEV dial Selecting Signal Flow Select the order in which signal processing occurs beat effect or digital jog break m Use the SIGNAL FLOW switch to select the signal processing order e When set to the JOG gt BEAT position signals are processed for digital jog break effects first followed by beat effects e
59. tal jog break No effect sound is heard when beat effects are applied EFFECT FREQUENCY indicators HI MID LOW are all off during use of DELAY ECHO PITCH ECHO effects If EFFECT FREQUENCY indicators are all off no effect sound will be output Press the button corresponding to the frequency band to which you wish to apply effects the button s indicator will light 25 lt DRB1369 gt OTHER SPECIFICATIONS Symptom Probably cause Remedy When a foot switch is connected effects are applied even without pressing the foot switch Foot switch s logic is reversed the effector applies effects when the foot switch is depressed for LOW level Use a foot switch with logic matching that of the effector Effect sounds are distorted Input level is too high Effect output level is too high Effect settings are too high When the DEPTH dial is set near its MAX position it may have the effect of raising the volume level Rotate INPUT LEVEL dial toward left MIN direction Try setting IN amp OUT LEVEL switch to the opposite position Rotate EFFECT OUT LEV dial toward left MIN direction Rotate DEPTH dial toward left MIN direction Can t use EFX LINK function The digital link cable is not connected The connected component is not supported The DJ mixer s settings are incorrect Connect the digital link cable to a DJ mixer with digital link support Set the
60. th 24 bit 96 kHz sampling allowing use in studio track creation and other applications where high sound quality is demanded CONTENTS FEATURES wisceccecesece cages suvesccthessceeccusceectcecvscnectevendatecascee 3 CONFIRM ACCESSORIES cccccceeesseeeeeeeeeeeetneeeeeees 3 QUICK OPERATION GUIDE USING BEAT EFFECTS BPM MODE ceeeeee 4 USING BEAT EFFECTS RHYTHM MODE 5 USING THE DIGITAL JOG BREAK eeeseeeeeeeeeee 6 USING JOG MEMORY PLAY eececeeeeeseeeeeeetteeeeeeeees 6 BEFORE USE CONNECTIONS concccnocccncnnoncnnnanncnnnanncnnnnnncnnnannnnnnanncncnnnns 7 Connection Panel cccscccesseceeesseeeeeeeseeeeeseeeeees 7 Basic Connections cccoooccccnnnoncnnnannncnnnnnannnnnnnnnnnnnnnos 8 EFFECTS unirlos 10 Beat EleciS nomina dia nt 10 Digital Jog Break siririn 12 Effect Parameters cocccconoccccnononnnnnonnncnnnnnnncnnanancnnno 13 CONTROLS AND FUNCTIONS ossein 14 Control Panel c ocoocccccnnoccccnanccnnnannccnnanacnnnnannncnnnncnnns 14 OPERATIONS OPERATIONS ecirocciciicaina clicar cartier cid rd 17 Adjusting Input Level oooonocccccccnncconancccccnnnnnnnnnannns 17 Adjusting Effect Output Level oooocccccnnocccccnnnnnnos 17 Selecting Signal FlOW eceeseeseseeeseeeeeneeeeeees 17 Selecting Foot Switch Operation sses 17 Selecting the Level Meter Display 17 Digital Link Function oocccnnnnnncnnnnnnnnnanannnananannnnn 17 Bypass FUNCTION coco
61. the sound level rises e The CHARACTER dial can be used to adjust the amount of filter applied to the feedback sound e The MIX dial can be used to adjust the levels of the original and delay sounds _ TIME oO o gt 2 ho c I Ee n 3 gt Time Original S sound Feedback Delay sound Delay block RHYTHM mode A delay sound set with the TAP button TAP delay sound is added to the original sound Max 8 TAP e The DEPTH dial can be used to adjust the TAP delay level near the MAX setting the sound volume will rise e The CHARACTER dial can be used to adjust the amount of filter applied to the TAP delay sound e The MIX dial can be used to adjust the levels of the original and TAP delay sounds o gt 2 o DEPTH 5 RET p c a tI 10 i i E sare IT gt Time Original Delay Delay Delay Delay sound sound sound sound sound a TAP 1 a TAP 3 an TAP 1 delay TAP 8 delay block 10 lt DRB1369 gt 2 ECHO effect Adds delay sound to the original sound BPM mode A delay sound is added to the original sound at the value set with the TIME dial RHYTHM mode Adds TAP delay sound to the original sound Max 8 TAP Difference from the DELAY effect e Even if the BEAT EFFECTS lever switch is moved from ON to OFF the feedback sound or TAP delay sound will continue e In the BPM mode if the DEPTH dial is set to MAX and the BEAT EFFECTS lever switch
62. to external sequencer or use an external sequencer to operate the EFX 1000 DJ CD player MIDI sequencer MIDI MIDI TRANSMIT MIDI START RECEIVE OFF TIME TAP EFX 1000 MIDI sequencer OUT OUT BPM Audio MIDI ee MIDI TRANSMIT A START RECEIVE OFF AR SET TIME TAP EFX 1000 1 Use a commercially available MIDI cable to connect the EFX 1000 s MIDI OUT connector and the MIDI sequencer s MIDI IN connector e The MIDI sequencer s sync mode should be set to slave e MIDI sequencers which do not support MIDI timing clock cannot be synchronized 2 Set MIDI switch to TRANSMIT position e Sync cannot be performed in the case of tracks whose BPM values cannot be measured stably e Timing clock is also output for BPM values set by using the TAP mode 3 Press the MIDI START CH SET button e MIDI timing clock output range is 40 250 BPM Setting TRANSMIT MIDI channel The TRANSMIT channel can be set and recorded in memory separately from the RECEIVE channel 1 Set MIDI switch to TRANSMIT position 2 In this co
63. ults to jog hold OFF indicator is off 38 DIGITAL JOG BREAK effect lever switch OFF ON ON LOCK Pull the lever toward you ON to output effected sounds In the middle position effects are OFF push the lever away from you to lock the lever in the ON LOCK position effects are locked ON When pulled to the ON position effects are output only while the lever is held when your finger is released the lever returns to middle OFF position 39 DIGITAL JOG BREAK effect indicator Lights when digital jog break effect is ON 40 Digital jog break effect selector buttons indicators JET WAH PHASE SHIFTER RING ZIP HUMANIZER VOCODER Press to select a desired digital jog break effect All the buttons light and the select effect button flashes When power is turned ON JET flashes 41 DIGITAL JOG BREAK METER During operation of the Jog dial and during jog memory play this meter lights to display the corresponding movement OPERATIONS OPERATIONS INPUT LEVEL FOOT SW MIDI TRANSMIT RECEIVE OFF EFFECT OUT LEV INPUT LEVEL SIGNAL FLOW FOOT SW MIDI MIDI EFFECT OUT LEV JOG gt BEAT JOG TRANSMIT METER MODE Fa START id MDISNAP roneer cHseT BYPASS BOTH RECEIVE INPUT J L m m m m m m m m m m m m m m O 145 10 7 5 3 2 a o 1 2 4 T 10 OVER B U OUTPUT R Mom m m m m m m m m m m O m MIN MAX BEAT g

Pioneer EFX-1000 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents