Pioneer DEQ-P7050 User's Manual
Contents
1. RCA cable supplied Left White Right Red me e e Rear audio output DYD REAR MONITOR OUTPUT rN Blue l IP BUS cable supplied Subwoofer output or non fading output SUBWOOFER OUTPUT or NON FADING OUTPUT D eUD Right Red D eUD Left White Optical cable supplied 3 m Front video output FRONT VIDEO sH OUTPUT Display with RCA m ae eee IP BUS cable Yellow Head unit input jacks e g DVH P7050 supplied with A ka the TV tuner H sold separately 3m Multi CD player RCA cables sold separately sold separately Biase wit iny AL Aadaos KITEN iii A ma Setete tanee Qe eee eee eee AV system display e g AVX 7300 sold separately Not used A Z Hide away TV tuner e g GEX P7000TVP sold separately FM MODULATOR IP BUS MAIN UNIT IP BUS AV MASTER RCA cable supplied with the head unit NN Red Right Red x oo eal Video input VIDEO INPUT ee Yellow Right Red r ofe MO em 20 pin cable supplied with the display Left White Installation Note Before finally installing the unit connect the wiring temporarily making sure it is all connect ed up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unautho rized parts can cause malfunctions Consult wi2. Precaution Try not to bend the optical cable sharply If it is necessary to bend it sharply make sure that the bending radius is at least 25 mm otherwise the cable will not transfer signals properly and so this unit will not work properly Route the optical cable so that nothing heavy rests on it and so that it cannot be stepped on or caught in anything for instance a door Make a loop of diameter at least 200 mm with the remaining optical cable so that the cable does not get strained When plugging the optical cable into the unit use the supplied cable clamps to prevent the cable from being bent sharply Route the optical cable so that it does not get caught in moving parts such as the gear shift hand brake or seat sliding mechanism Keep the cable away from hot spots such as near the heater outlet Using the corrugated tube To prevent the optical cable from being strained use the corrugated tube after cutting it to the cor rect length e Insert the optical cable into the cor rugated tube Optical cable Corrugated tube lt ENGLISH gt The clamp is used to secure the optical cable when using it The other clamp is installed on the back side of the head unit similarly and used to secure the optical cable 1 Insert the clamp in the direction indicated in the figure and turn it 90 degrees to lock
3. There is a pos sibility of short circuiting if the leads are not insulated To prevent incorrect connection the input side of the IP BUS or optical cable connector is blue and the output side is black Connect the connec tors of the same colors correctly If this unit is installed in a vehicle that does not have an ACC accessory position on the ignition switch the red lead of the unit should be con nected to a terminal coupled with ignition switch ON OFF operations If this is not done the vehi cle battery may be drained when you are away from the vehicle for several hours ACC position No ACC position The black lead is ground Please ground this lead separately from the ground of high current prod ucts such as power amps If you ground the products together and the ground becomes detached there is a risk of dam age to the products or fire To ensure proper heat dissipation of this product take special care not to block the cooling fan side of this product Cords for this product and those for other prod ucts may be different colors even if they have the same function When connecting this prod uct to another product refer to the supplied Installation manuals of both products and con nect cords that have the same function Connecting the power cord This product When you connect a power amp sold separately be sure to use the blue white lead of this unit If you use the blue white lead of the
4. head unit it causes noises Blue white To system control terminal of the power amp or Auto antenna relay control terminal max 300 mA 12 V DC Yellow ae Fuse holder To terminal always supplied with power regardless of ignition switch position Black ground To vehicle metal body Black white x Center speaker Black Left White Gray Right Front speaker Front speaker White black Gray black Green Violet Rear speaker Rear speaker Green black Violet black Do not connect anything to the speaker leads that are not connected to speakers lt ENGLISH gt Connecting to a sold separately power amp This product can be connected to a sold separately power amp using the RCA output jacks RCA cables sold separately Front speaker Rear speaker Center speaker This product System remote control Blue white To system control terminal of the power tT amp or Auto antenna relay control terminal max 300 mA 12 V DC When you connect a power amp sold separately be sure to use the blue white lead of this unit If you use the blue white lead of the head unit it causes noises Power amp sold separately Power amp sold separately Power amp sold separately Power amp sold separately Connecting the Units lt ENGLISH gt Connecting the system Rear video output REAR VIDEO OUTPUT Yellow
5. Pioneer sound vision soul l L _ lt a lt L e s This product conforms to new cord colors PRINTED WITH SOY INK AS re ES ARE Printed in Japan H ASE hil lt CRD3605 B gt ES DEQ P7 050 lt KMMUF 02B00000 gt Connecting the Units Note This unit is for vehicles with a 12 volt battery and negative grounding Before installing it in a recreational vehicle truck or bus check the bat tery voltage To avoid shorts in the electrical system be sure to disconnect the battery cable before begin ning installation Refer to the owner s manual for details on con necting the power amp and other units then make connections correctly Secure the wiring with cable clamps or adhesive tape To protect the wiring wrap adhesive tape around them where they lie against metal parts Route and secure all wiring so it cannot touch any moving parts such as the gear shift hand brake and seat rails Do not route wiring in places that get hot such as near the heater outlet If the insulation of the wiring melts or gets torn there is a danger of the wiring short circuiting to the vehicle body Don t pass the yellow lead through a hole into the engine compartment to connect to the battery This will damage the lead insulation and cause a very dangerous short Do not shorten any leads If you do the protec tion circuit may fail to work when it should Never feed
6. power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead The current capac ity of the lead will be exceeded causing over heating When replacing fuse be sure to use only fuse of the rating prescribed on the fuse holder Since a unique BPTL circuit is employed never wire so the speaker leads are directly grounded or the left and right speaker leads are common Speakers connected to this unit must be high power types with minimum rating of 50 W and impedance of 4 to 8 ohms Connecting speakers with output and or impedance values other than those noted here may result in the speakers catch ing fire emitting smoke or becoming damaged When this product s source is switched ON a control signal is output through the blue white lead Connect to an external power amp s system remote control or the car s Auto antenna relay control terminal max 300 mA 12 V DC If the car features a glass antenna connect to the anten na booster power supply terminal When an external power amp is being used with this system be sure not to connect the blue white lead to the amp s power terminal Likewise do not connect the blue white lead to the power ter minal of the auto antenna Such connection could cause excessive current drain and malfunction To avoid short circuiting cover the disconnected lead with insulating tape Especially insulate the unused speaker leads without fail
7. th your nearest dealer if installation requires the drilling of holes or other modifica tions of the vehicle Install the unit where it does not get in the dri ver s way and cannot injure the passenger if there is a sudden stop like an emergency stop When mounting this unit make sure none of the leads are trapped between this unit and the sur rounding metalwork or fittings Do not mount this unit near the heater outlet where it would be affected by heat or near the doors where rainwater might splash onto it Before drilling any mounting holes always check behind where you want to drill the holes Do not drill into the gas line brake line electrical wiring or other important parts If this unit is installed in the passenger compart ment anchor it securely so it does not break free while the car is moving and cause injury or an accident If this unit is installed under a front seat make sure it does not obstruct seat movement Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit Installing the unit Mounting with brackets gT Tapping screw 4 x 12 mm I Screw Al 4x8 mm y N x Car mat or chassis Drill 2 to 2 5 mm diameter holes Mounting with velcro tape Thoroughly wipe off the surface before affixing the velcro tape Velcro tape Car mat or chassis Routing the optical cable
Download Pdf Manuals
Related Search