Philips TC8275 User's Manual
Contents
1. The cover is fastened o the chassis by two screws on the bottom near the rear of the unit Disassembly is as shown Slide Cover Back Remove Screws From Bottom Rear Corners S936A0IAE 2 Places Cover Removal 4 4 Video Inputs All camera inputs should utilize 2 1 interlaced format cameras to achieve a real time update rate 30 frames per second when used with line locked cameras that have a phase error of less than 5 degrees 4 4 1 TC8275 Series Connect up to four cameras to the unit A single BNC connector 75 ohm terminated is provided for each camera input See Typical Application TC8275 Series CAUTION The cover must be removed to make any DIP switch adjustments These settings should only be performed by a qualified installer or service center See Location of DIP Switches under ILLUSTRATIONS 4 4 2 TC8277 Series Connect up to four cameras to the unit See Back Panel TC8277 Series under ILLUSTRATIONS There are two BNC connectors on the rear panel for each of the four camera inputs Use either one of these connectors as a camera input the other connector may be used as a looping output DIP switch S2 controls the 75 ohm termination for each of the 4 video inputs S2 is switched ON for 75 ohm termination or OFF for nonterminated looping operation The factory default is set for 75 ohm terminated operation See Typical Application TC8278 Series under ILLUSTRATIONS Note that a typical application for TC8272. 4 and 5 8 For example camera 6 can be displayed along with cameras 3 and 4 To return to the standard quad pages of 4 and 5 8 press QUAD which selects the first quad page of cameras 4 and then select sequencing or the alternate page as desired If the MON A monitor is in full screen display mode the SEQ button will be ignored Full screen displays on the MON A monitor cannot be sequenced 5 2 9 FREEZE Button Freezes or unfreezes all quadrants of the MON A monitor display Only images displayed on the MON A monitor output can be frozen The FREEZE button has no effect on MON B monitor displays The FREEZE button is used both to freeze and to unfreeze displays The operator can freeze any image on the MON A monitor Full screen displays one quadrant of a quad display or all quadrants of a quad display can be frozen via a front panel FREEZE button for further investigation of the image Note FREEZE always stops any sequencing in the frozen quadrant s of the image Selecting alternative modes by pressing SEQ QUAD or ZOOM also unfreezes the display Freezing All Quadrants When no active quadrant is selected on the MON A monitor output FREEZE will cause all 4 quadrants of the present quad display to be frozen If the FREEZE button is pressed again it will unfreeze all quadrants Freezing Individual Quadrants If an active quadrant has been selected refer to Arrow Buttons the FREEZE button will cause o
3. interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Intentional or unintentional changes or modifications not expressly approved by the party responsible for compliance shall not be made Any such changes or modifications could void the user s authority to operate the equipment The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Caution To reduce the risk of electrical shock do not open covers No user serviceable parts inside Refer servicing to qualified service personnel SECURITE ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Danger Pour viter tout risque d lectrocution ne pas ouvrir le bo tier ll n y a pas de pi ces rempla ables a l int rieur Pour toute r vision s adresse
4. 20 Coax Grounding If an outside cable system is connected to the unit be sure the cable system is grounded U S A models only Section 810 of the National Electrical Code ANSI NFPA No 70 1981 provides information with respect to proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode 21 Lightning For added protection of this unit during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the cable system This will prevent damage to the unit due to lightning and power line surges FCC amp ICES INFORMATION U S A and Canadian Models Only WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules and ICES 003 of Industry Canada These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful
5. Application TC8278 Series S9505017AE Alarm Accessory Connector Pin Out Pin Function Pin Function Pin Function Ground 6 Alarm Il Alarm 2 2 Alarm 3 7 Alarm 4 12 Alarm 5 3 Alarm 6 8 Alarm 7 13 Alarm 8 4 Alarm Clear 9 Alarm Relay NO 14 Alarm Relay NC 5 No Connection 10 No Connection 15 Vidloss OUT NO Normally Open Relay to ground NC Normally Closed Relay to ground S929A45AE MAIN MENU CHANGE PASSWORD CAMERA TITLES ALARMS REMOTE SEQUENCE lt SELECT gt TO SELECT LIST CHANGE PASSWORD CAMERA TITLES ALARMS REMOTE SEQUENCE CLOCK EXIT TITLES MENU TITLE DISPLAY EDIT TITLE EXIT lt SELECT gt TO SELECT CHANGE PASSWORD ENTER NEW PASSWORD kkk lt MENU gt TO ABORT SEQUENCING MENU MON B LIST MON B DWELL QUAD DWELL EXIT lt SELECT gt TO SELECT CLOCK MENU TIME DATE DISPLAY TIME DATE FORMAT SET TIME SET DATE EXIT lt SELECT gt TO SELECT TITLES DISPLAY MENU QUAD ON MON B OFF 4 ON OFF lt SELECT gt TO EXIT CONFIRM NEW PASSWORD RE ENTER kkk lt MENU gt TO ABORT EDIT CAMERA TITLE CAMERA 1 CAMERA 2 CAMERA 3 CAMERA 4 CAMERA 5 lt SELECT gt TO SELECT EDIT CAMERA TITLE CAMERA 1 CAMERA A A 4 gt MOVE CURSOR lt SELECT gt TO EXIT 4 CHANGE CHARACTER CAM
6. Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 17 Damage Requiring Service Unplug the unit from the outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the unit c If the unit has been exposed to rain or water d Ifthe unit does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation e If the unit has been dropped or the cabinet has been damaged f When the unit exhibits a distinct change in performance this indicates a need for service 18 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 19 Safety Check Upon completion of any service or repairs to this unit ask the service technician to perform safety checks to determine that the unit is in proper operating condition
7. alimentation principale pour tous les appareils Changement de piles Attention Danger d explosion si le changement de pile n est pas effectu correctement N utilisez que des piles du m me type ou d un type quivalent recommand par le fabricant Veuillez respecter les consignes du fabricant lorsque vous jetez les piles usag es Sources d alimentation ext rieures Utiliser uniquement les sources d alimentation recommand es Les sources d alimentation doivent tre conformes aux r glementations de la derni re version IEC 65 VDE 0860 Toute modification peut endommager l appareil ou provoquer un incendie ou un choc lectrique SICHERHEITSVORKEHRUNGEN PRECAUCIONES DE SEGURIDAD VORSICHT RISIKO EINES ELEKTRISCHEN SCHLAGES NICHT OFFNEN PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR Precaucion Para Reducir El Riesgo De Choque El ctrico Favor No Abrir La Cubierta Este Equipo No Consta De Piezas O Partes Que Requieren Servicio O Mantenimiento Para Reparaciones Favor Referirse A Un T cnico Calificado VORSICHT Um einen elektrischen schlag zu vermeiden abdeckung nicht entfernen Wartungen aller art qualifiziertem personal berlassen Debido a limitaciones de espacio esta etiqueta puede aparecer en la parte Aus Platzgriinden kann diese Warnung auf der Unterseite des Ger tes inferior de la unidad angebracht sein nicht isolierte Hochspannung im Geh use aufmerksam machen die eventuell stark ge
8. automatically reset and the unit reverts to quad mode Pressing the QUAD button at any time will exit the active quadrant mode 5 2 5 ZOOM Button Operates only on the MON A monitor Used to switch from quad displays to full screen displays on the Quad monitor and also to zoom the full screen displays Full screen Display Selection If an active quadrant is first selected displays the corresponding camera full screen If no active quadrant is selected it operates on the last active quadrant that was selected for full screen display Once in full screen mode the arrow buttons will switch to alternate full screen views 5 2 6 Zoom Mode Zooms a full screen camera display using a digital 2X Zoom Zooms the VCR display on the MON A monitor If a display is already zoomed then pressing the ZOOM button toggles the display back to full screen The indicator ZOOM is displayed if an image has been zoomed Once a full screen display has been zoomed the arrow buttons can be used to continuously pan and tilt around the zoomed display Note that frozen full screen images cannot be zoomed However zoomed displays are fully interlaced and can be frozen at any time 5 2 7 VCR Button Selects for display on MON A and MON B the video source that is connected to the VCR BNC on the rear panel If the source is playback from a time lapse VCR playback speed must be in the 2 hour mode for proper operation For best performan
9. must not be defeated 4 2 Mounting These units are supplied as desk top units For rack mounting the LTC 9101 00 Rack Kit is available These units are half rack units 4 3 Cover Removal WARNING Removal of the cover should only be performed by qualified service personnel not user serviceable The unit should always be unplugged before removing the cover and remain unplugged while the cover is removed 4 3 D montage du Couvercle Le d montage du couvercle et le r glage des commandes internes doivent etre effectues par du personnel qualifi pas de service par l utilisateur L appareil doit toujours tre d branch lorsque l on retire le couvercle et doit rester d branch pendant que le couvercle est t 4 3 Entfernung der Abdeckung Z N Die Entfernung der Abdeckung und Hantieren im Innern des Ger tes sollten nur von qualifiziertem Personal erfolgen Der Stecker des Ger tes sollte immer aus der Steckdose gezogen werden bevor man die Abdeckung entfernt und nicht wieder hineingesteckt werden solange die Abdeckung entfernt ist 4 3 Desensamble de la Cubierta Atencion La cubierta ha de ser removida solo por personal de servicio autorizado este equipo no contiene partes que requieran mantenimiento por usuarios Antes de remover la cubierta asegurarse de que el equipamiento ha sido desconectado de la alimentacion Esta debe permanecer desconectada mientras la cubierta este fuera de lugar
10. programmable via the menu The sequence list can include any camera or the MON A display in the list several times and in random order To start stop sequencing on the MON B output select MON B followed by SEQ 5 3 The product is equipped with 4 alarm inputs TC8277 Series or 8 alarm inputs TC8278 Series each associated with its corresponding video input System action during an active alarm includes on screen indication of the camera in alarm ALM a front panel LED indicator an alarm output relay and the MON B monitor switching to the camera in alarm If multiple cameras are in alarm the MON B monitor automatically sequences between the cameras in alarm at a preset dwell rate of second Alarm Input Operation The alarm inputs are configured as zero potential relay contacts individually programmable via the menu to be normally open NO or normally closed NC Refer to the setup MENU to select the input configuration as NO or NC Any alarm inputs can be enabled or disabled via the setup MENU Alarms may be cancelled acknowledged via a contact to ground on a rear panel input or by pressing the SELECT button 5 3 1 Alarm Input Handling There are three ways of handling alarms which may be selected by the operator in the setup MENU 5 3 2 Latched Alarms Alarms are latched as they become active An alarm is cleared when the operator acknowledges it There is no time out period Note When the operator acknowle
11. the operator on the correct buttons to use for various options and functions 5 1 2 Selecting Menu Items Move up and down through the menu by using the up and down arrow buttons and choose a menu item by pressing the SELECT button This will bring up a new screen which allows the operator to select options or enter data related to the menu item which was chosen Option Selection In menu screens where items in a list must be turned ON or OFF use the left or right arrow buttons to toggle the status of the current entry then press the down arrow button to move on to the next entry The up or down arrow buttons are used to skip over or select entries on the screen When there are more entries than can be displayed on one screen the screen will scroll automatically when the down arrow is pressed on the bottom entry The up arrow can be used to scroll up to preceding entries if needed Press SELECT when done to exit the screen 5 1 3 Data Entry Some menu screens provide a means for the operator to enter numeric or alpha numeric data In these menus a current cursor indication is provided by means of the Up Arrow character below the position at which data is to be entered The up and down arrow buttons will then cycle through the displayable character set while the left and right arrow buttons are used to move to subsequent or preceding character locations Once all characters have been set up correctly the SELECT button will conf
12. 1C8275 Series TC8277 Series 1C8278 Series VidQuad Color Video Processors Q VI 2 am VI CC O D U an D un Philips PHILIPS Communication amp Security Systems IMPORTANT SAFEGUARDS I Read Instructions All the safety and operating instructions should be read before the unit is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the unit and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Cleaning Unplug the unit from the outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 6 Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards 7 Water and Moisture Do not use this unit near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement near a swimming pool in an unprotected outdoor installation or any area which is classified as a wet location 8 Accessories Do not place this unit on an unstable stand tripod bracket or mount The unit may fall causing serious injury to a person and serious damage to the unit Use only with a stand tripod bracket or mount recommended by the manufacturer or sold with the product Any mounting of the unit should follow the lt m
13. 7 Series is similar to that for the TC8278 Series 4 4 3 TC8278 Series Connect up to eight cameras to the unit See Typical Application TC8278 Series under ILLUSTRATIONS There are two BNC connectors on the rear panel for camera inputs thru 7 Use either one of these connectors as a camera input the other connector may be used as a looping output Camera input 8 has a single BNC connector DIP switches SI and S2 control the 75 ohm termination for each of the 8 video inputs SI and S2 are switched ON for 75 ohm termination or OFF for nonterminated looping operation The factory default is set for 75 ohm terminated operation 4 5 Monitor Outputs 4 5 1 TC8275 Series Connect a monitor to the QUAD VIDEO OUT See Typical Application TC8275 Series 4 5 2 TC8277 Series and TC8278 Series Connect monitors to MON A and MON B outputs The monitor outputs must be terminated in a 75 ohm load If the monitor output line is looped through monitors or other equipment be sure the monitor terminations are set to Hi Z Only the last unit on the line should have its termination set to 75 ohm See Typical Application TC8278 Series under ILLUSTRATIONS 4 6 Alarm Inputs and Output Accessory Output 4 6 1 TC8277 Series and TC8278 Series The 609 mm 24 in cable with 15 pin connectors provided with the VidQuad units are for use with the mating alarm input output and accessory connectors These cables can be cut to desired length a
14. 78 Series subsequent pressing the QUAD button will toggle between alternate quad pages cameras thru 4 and then cameras 5 thru 8 5 2 4 ARROW Buttons Used to select an active quadrant on the MON A monitor Each arrow button is mapped to a quadrant on the screen and will alternately select the two cameras associated with that quadrant In the MON A monitor display the operator can operate on either the full screen display or only on individual quadrants of the display To operate on individual quadrants in the quad display an active quadrant must first be selected by the operator from the four displayed images Active Quadrant Selection If any of the arrow buttons are pressed while the MON A monitor is in quad display mode an active quadrant is indicated in the corresponding quadrant of the quad display The active quadrant is indicated by flashing the camera number and title of the camera in that quadrant Adjacent quadrants can be selected as the current active quadrant by pressing the appropriate arrow buttons If no further buttons are pressed the active quadrant mode will automatically time out While the active quadrant indication is active buttons like SEQ FREEZE and ZOOM will affect only the active quadrant as opposed to the whole page of the quad display Active Quadrant De selection The active quadrant display indication stays visible for approximately 5 seconds after the last keystroke after which it is
15. ARM ENABLE DISABLE ALL ENABLE ALL INDIVIDUAL ENABLE lt SELECT gt TO SELECT ALARMS ENABLE CAMERA 1 ENABLE CAMERA 2 DISABLE CAMERA 3 ENABLE CAMERA 4 ENABLE lt gt ENABLE DISABLE lt SELECT gt TO EXIT S9505014BE Notes 3935 890 09611 98 42 1998 Philips Electronics N V Printed In U S A 1998 Philips Communication amp Security Systems Inc All Rights Reserved Philips is a registered trademark of Philips Electronics N V Data subject to change without notice
16. ERA 2 CAMERA 3 CAMERA 4 CAMERA 5 CAMERA 6 CAMERA 7 CAMERA 8 On TC8278 X models only MON B SEQ LIST 12345678Q SELECT CAMERA 4 MOVE CURSOR lt SELECT gt TO EXIT TIME DATE DISPLAY QUAD OUTPUT ON MON B OUTPUT OFF lt gt ON OFF lt SELECT gt TO EXIT MON B SEQ DWELL TIME 005 SECONDS CHANGE NUMBER lt SELECT gt TO EXIT TIME DATE FORMAT TIME 12 HOUR DATE MM DD YY lt gt SELECT FORMAT lt SELECT gt TO EXIT QUAD SEQ DWELL TIME 005 SECONDS CHANGE NUMBER lt SELECT gt TO EXIT SET TIME HH MM SS AM PM 12 00 00 AM 4 CAMERA NUMBER 4 CHANGE FIELD lt SELECT gt TO EXIT SET DATE MM DD YY 01 01 95 CHANGE NUMBER 4 p CHANGE FIELD lt SELECT gt TO EXIT REMOTE MENU 1200 BAUD 2400 BAUD 4800 BAUD 9600 BAUD lt SELECT gt TO SELECT Menus Flow Chart ALARMS MENU QUAD FULL ON INPUT CONFIG MODE ENABLE EXIT ON OFF lt SELECT gt TO SELECT ALARM INPUT CAMERA 1 N OPEN CAMERA 2 N OPEN CAMERA 3 N CLOSED CAMERA 4 N OPEN CAMERA 5 N OPEN gt NO NC lt SELECT gt TO SELECT ALARM MODE LATCHED TRANSPARENT TIMED OUT lt SELECT gt TO SELECT ALARM TIMEOUT TIME 020 SECONDS CHANGE NUMBER lt SELECT gt TO EXIT AL
17. T be in full screen display mode when starting sequencing The full screen or zoomed displays on the quad monitor cannot be sequenced To start sequencing of an individual quadrant which is not already sequencing first press any arrow button once to initiate the active quadrant mode then use the arrow buttons to select the quadrant and press SEQ This will immediately start sequencing in the active quadrant while the status of the other quadrants will not be affected If sequencing is required in other individual quadrants use the arrow buttons to select a new active quadrant and press SEQ The active quadrant automatically times out in 5 seconds after there is no button activity so when all quadrants have been programmed there is no further action required by the operator to exit the active quadrant mode Alternatively pressing QUAD at any time will end the active quadrant mode Quadrants will sequence between the two input cameras related to the quadrant namely and 5 2 and 6 3 and 7 and 4 and 8 respectively To stop sequencing of one individual quadrant use the arrow buttons to select the appropriate quadrant and press SEQ To stop sequencing of all quadrants press QUAD This stops sequencing and automatically selects the camera thru 4 quad display Note that on the T C8278 Series by starting and stopping sequencing in individual quadrants the user can get page displays different to the standard pages of cameras
18. allation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes Power Disconnect Units with or without ON OFF switches have power supplied to the unit whenever the power cord is inserted into the power source however the unit is operational only when the ON OFF switch is in the ON position The power cord is the main power disconnect for all units Battery Replacement Caution Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions External Power Supplies Use only the Recommended Power Supplies Power supplies must comply with the requirements of the latest version of IEC 65 VDE 0860 Substitutions may damage the unit or cause a fire or shock hazard gt gt gt gt Attention L installation doit tre effectu e uniquement par du personnel de service qualifi conform ment a la r glementation du Code Electrique National ou la r glementation locale Disjonction de l alimentation Les appareils avec ou sans commutateurs ON OFF sont aliment s chaque fois que le cordon d alimentation est branch la source d alimentation toutefois les appareils disposant de commutateurs ON OFF ne fonctionnnent que lorsque le commutateur ON OFF est sur la position ON Le cordon d alimentation est la disjonction d
19. anufacturer s instructions and should use a mounting accessory recommended by the manufacturer a An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn 9 Ventilation Openings in the enclosure if any are provided for ventilation and to ensure reliable operation of the unit and to protect it from overheating These openings must not be blocked or covered This unit should not be placed in a built in installation unless proper ventilation is provided or the manufacturer s instructions have been adhered to 10 Power Sources This unit should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply you plan to use consult your appliance dealer or local power company For units intended to operate from battery power or other sources refer to the operating instructions Il Grounding or Polarization This unit may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Alternately this unit ma
20. ce when using the VCR input selection it is recommended that both record and playback of the quad video be in the 2 hour mode Initiating VCR Playback Mode VCR playback is initiated by pressing the VCR button on the front panel which will route the VCR input to both the MON A and the MON B monitors During this mode the text VCR is displayed on the monitors The MON A monitor can be used to display live playback images frozen images or zoomed images of one quadrant of the playback Freeze During VCR Playback To freeze or unfreeze the display at any time during VCR playback press FREEZE The text FRZ will indicate that the image is frozen Zoomed images can also be frozen The use of the VCR s PAUSE button can also freeze the image being displayed Using the pause feature of the VCR will stop video update as the image is frozen allowing for greater control of the playback Zoom During VCR Playback To zoom a quadrant in the recorded VCR display on the MON A monitor select that quadrant as the active quadrant by using the arrow buttons An asterisk will indicate the active quadrant Press ZOOM to zoom that quadrant to full screen display Once in Zoom mode the arrow buttons will act as Pan and Tilt controls Press ZOOM or the QUAD button to return to normal VCR playback The MON B monitor will continue to display the full VCR signal continuously The dual VCR input displays give the user maximum flexibility to exa
21. dges cancels the alarm it will be cleared whether the alarm input is still active or not Alarms that have been acknowledged by the operator will not be reactivated until the alarm input has ceased and then restarts 5 3 3 Timed out Captured Alarms Timed out alarms are latched for a minimum time out period from the start of the alarm becoming active The time out period is menu programmable After expiration of the time out period the alarm is automatically cleared Alarm inputs that are still active after the time out become manual type alarms Alarms that cease and restart before the time out is complete will restart the time out period Timed out alarms can be cleared by the operator before they time out Alarms that are cleared before their inputs have ceased will not be reactivated until the alarm input ceases and restarts 5 3 4 Manual Alarms No Capture Alarms are active only while the alarm input is active As soon as the alarm input ceases the alarm is cleared 5 3 5 Clearing Alarms Alarms are cleared by pressing SELECT ALARM CLR or by pulling a rear panel contact pin 4 to ground Refer to the rear panel drawing for the location of the contact 5 3 6 Upon video loss to any input the corresponding camera image on the MON A display is automatically frozen and a video loss warning message VDL is displayed on the corresponding quadrant as well as on the associated MON B monitor display If the MON A moni
22. fully Check for the following items Model No of unit e One cable with a 15 pin connector on one end Supplied only with TC8277 Series and TC8278 Series models If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper If any items are missing notify your Philips Communication amp Security Systems Inc Sales Representative or Customer Service The shipping carton is the safest container in which the unit may be transported Save it for possible future use 2 SERVICE If the unit ever needs repair service the customer should contact the nearest Philips Communication amp Security Systems Inc Service Center for authorization to return and shipping instructions Service Centers U S A amp Canada 800 366 2283 Mexico amp Central America 52 5 564 2726 Europe amp Middle East 44 1932 765666 South America 54 1 956 0837 Australia 6 2 888 9000 New Zealand 64 4 237 7297 hiss ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES WARNING Electrostatic sensitive device Use proper CMOS MOSFET handling precautions to avoid electrostatic discharge NOTE Grounded wrist straps must be worn and proper ESD safety precautions observed when handling the electrostatic sensitive printed circuit boards 3 DESCRIPTION These video processors digitally capture the full video from color or monochrome sources reduces these images to q
23. gt gt gt dentro de un triangulo equilatero se muestra con el objetivo de alertar al usuario que existen voltages peligrosos sin aislamiento dentro de la cubierta de la unidad Dichos voltages pueden ser de tal magnitud que constituyen un riesgo de choque el ctrico a personas l El simbolo representado por un relampago con punta de flecha El s mbolo de exclamaci n dentro de un tri ngulo equil tero se muestra con el objetivo de alertar al ususario de que instrucciones de operaci n y mantenimiento importantes acompa an al equipo Peligro Para evitar el peligro de incendio choque el ctrico no exponga a la lluvia humedad equipos que no han sido para uso exterior AN eN eN eN Atenci n La instalaci n de este equipo debe ser realizada por personal capacitado solo en acuerdo y en cumplimiento de normas del National Electric Code C digo El ctrico Nacional 6 las normas del Gobierno Nacional Local Para Desconectar la Alimentacion Unidades no equipadas con interruptores ON OFF son alimentadas cuando el cable de alimentaci n es conectado a la corriente el ctrica Las unidades equipadas con interruptores son alimentadas de igual forma pero adicionalmente requieren que el interruptor est posicionado en ON El cable de alimentaci n es el medio principal de desconexi n del equipo Advertencia Reposicion de Bater a Peligo de explosion si la bater a es reemplazada incorrectamente Reem
24. include any input several times and in random sequence The sequence dwell times for the MON A and MON B monitors can be set separately by the operator via the menus 5 2 11 MON B Button Used to toggle the front panel control from MON A control to MON B control and visa versa Fixed full screen displays can be selected on the MON B monitor by pressing MON B followed by the appropriate arrow button Each arrow button is mapped to a quadrant on the screen and will alternately select the two cameras associated with that quadrant The MON B monitor output is analog Digital functions such as zoom and freeze have no effect on the MON B monitor output A flashing MON B indication on the monitors advises the user that the front panel is controlling the MON B monitor 5 2 12 ARROW Buttons MON B Used to select a camera for display on the MON B monitor provided that the MON B button is pressed before the arrow button Each arrow button is mapped to a quadrant on the screen and will alternately select the two cameras associated with that quadrant 5 2 13 SEQ Button MON B Sequencing on the MON B monitor output may be toggled on and off by using the SEQ button To start sequencing while in the MON B mode press the SEQ key Sequencing will commence at the MON B sequence dwell time The MON B monitor dwell time is programmable between and 99 seconds The MON B sequence list can contain up to l6 entries which are operator
25. irm the data entry and call up the subsequent camera if applicable If there is no subsequent camera then SELECT will return the operator to the main menu 5 1 4 Menu programming can be terminated at any point by pressing the MENU button again Terminating Menu Programming All changes are automatically saved by the system as they are made Settings are retained even on loss of power 5 2 Monitor Operation 5 2 1 Monitor Display Outputs The front panel buttons can be used to operate either on the MON A monitor display or on the MON B monitor display The MON A monitor displays a digitized image and so Zoom and Freeze operations can be performed on the MON A monitor The MON B monitor displays analog full screen images only and so quad compression Zoom and Freeze cannot be performed on the MON B monitor output 5 2 2 Mon A Monitor Display The first monitor output designated as the MON A monitor is used mainly for quad displays It will simultaneously display four camera images which have been digitally compressed to one quarter of normal size along with camera ID titles and status information The MON A monitor can also be used for digital full screen camera display manually or via alarm inputs so that if an installation is not suited to the use of two display monitors the operator still can have full screen call up capability 5 2 3 QUAD Button Selects the quad display on the MON A monitor output On the TC82
26. mine VCR playback To exit VCR mode Press VCR 5 2 8 SEQ Button Starts or stops sequencing on the MON A quad displays for the TC8278 Series only For full screen sequencing refer to Monitor B operation Quad Page Sequencing T C8278 Series Only In this mode the SEQ button may be used to toggle the sequencing of the two quad pages on and off To start sequencing of the two quad pages on the MON A output press SEQ This will cause a quad display of cameras thru 4 to sequence with a quad display of cameras 5 thru 8 at the quad sequence dwell time Note that an active quadrant must not be selected at the time that quad page sequencing is selected If there is an active quadrant displayed on the screen first press QUAD and then SEQ to start full quad sequencing The quad sequence dwell time is menu programmable between and 99 seconds To stop quad page sequencing the operator can either press SEQ or press QUAD Note that pressing an arrow button to select an active quadrant during full quad display sequencing will allow an operator to stop or re start the sequencing of any one quadrant at a time as explained below If sequencing is in progress on either monitor it will be indicated on screen on the corresponding monitor s by the indicator SEQ Individual Quadrant Sequencing TC8278 Series Only The operator can also sequence individual quadrants while other quadrants remain static The MON A monitor must NO
27. nd the end insulation stripped off for connecting external devices 4 7 Alarm Inputs 4 7 1 TC8277 Series and TC8278 Series The alarm inputs are defaulted to be normally open These can be individually changed to normally closed via the Alarm menu CAUTION Do not apply external voltages to the alarm inputs Belden 8760 twisted shielded cable or equivalent should be used for wiring to the alarm connector and the total length of unshielded cable should not exceed 10 cm 3 9 in on each connector port to maintain compliance with Directive 89 336 EEC Use only isolated closures or open collector logic Precautions should be taken particularly on long runs to prevent pickup of spurious signals from associated wiring which may give false inputs or damage the unit Refer to the Alarm Accessory Connector Pin Out under ILLUSTRATIONS 4 8 N N Alarm Output 4 8 1 TC8277 Series and TC8278 Series The alarm output is a relay which is configured to be normally open The relay contacts can handle up to ampere at 40 volts AC DC and will close upon alarm input to the unit The video loss output is a logic low Refer to the Alarm Accessory Connector Pin Out under ILLUSTRATIONS 5 OPERATION 5 1 Menu Operation In setup mode the user has access to on screen menus for programming system settings and installation data such as Titles Alarm Operation Sequencing Operation Time Date Setup Password Setup Remote Configurati
28. nly the active quadrant to be frozen or unfrozen Freezing a Full screen or Zoomed Image If a full screen or zoomed image has been selected on the MON A monitor output FREEZE will cause the MON A monitor display to be frozen If the FREEZE button is pressed again it will unfreeze the display Unfreezing a Display Besides using the FREEZE button as indicated above any frozen display will be automatically unfrozen when a mode change is requested by using the QUAD SEQ VCR or ZOOM buttons 5 2 10 MON B Monitor Display The secondary monitor output designated as the MON B monitor is used for selecting analog full screen displays of any one of the eight camera inputs or to display a sequenced list of full screen displays The MON B monitor output is analog and so digital functions such as quad compression zoom and freeze are not available on the MON B monitor The operator can either select full screen displays of any camera to the MON B monitor or the displays can be selected automatically to the MON B monitor screen as a result of an external alarm input Full screen camera views can be sequenced on the MON B monitor The MON B monitor can also display the same images that are being displayed at any one time on the MON A monitor The MON B monitor sequence list can include any of the input cameras as well as the quad images selected for the quad display monitor The MON B sequence list can accept up to sixteen entries and can
29. nug ist um einen elektrischen Schlag zu verursachen Das Blitzsymbol im gleichseitigen Dreieck soll den Benutzer auf Das Ausrufezeichen im gleichseitigen Dreieck soll den Benutzer auf wichtige Bedienungs und Wartungsanleitungen in der dem Ger t beigef gten Literatur aufmerksam machen Warnung Um Feuer oder elektrische Schlage zu vermeiden setzen Sie das Ger t niemals Regen oder Feuchtigkeit aus Achtung Die Installation sollte nur von qualifiziertem Kundendienstpersonal gem jeweilig zutreffender Elektrovorschriften ausgef hrt werden NetzanschluB Ger te mit oder ohne Netzschalter haben Spannung am Ger t anliegen sobald der Netzstecker in die Steckdose gesteckt wird Das Ger t ist jedoch nur betriebsbereit wenn der Netzschalter EIN AUS auf EIN steht Wenn man das Netzkabel aus der Steckdose zieht dann ist die Spannungszuf hrung zum Ger t vollkommen unterbrochen Vorsicht beim Austauschen von Batterien Wird die Batterie unsachgem B ausgetauscht besteht Explosionsgefahr Batterien stets nur durch gleiche oder gleichwertige vom Hersteller empfohlene ersetzen Gebrauchte Batterien gem f Anweisungen des Herstellers entsorgen Externe Netzger te Nur vom Hersteller empfohlene Netzgerate verwenden Die Netzger te m ssen der jeweils g ltigen Version der IEC 65 VDE 0860 Bestimmungen entsprechen Andere Ersatznetzger te k nnen das vorliegende Ger t besch digen und Feuer oder Elektroschlag bewirken
30. ons For an overview of operator programmable menu options refer to Menus Flow Chart under ILLUSTRATIONS Menu operation is password protected to prevent unauthorized access and can be set by the user Although the menus include EXIT selections the MENU button can be pressed at any time while in the menus to immediately exit the setup mode and return to normal operation Any programming made up to the menu exit time will be saved 5 1 1 To start a menu programming session press the MENU button Initiating Menu Programming The operator will be prompted to enter a password consisting of a three button sequence of the front panel buttons The password can be programmed by the operator The factory setting for the password is SELECT SELECT SELECT Note that the SELECT button is not normally a valid password button and cannot be used in a new password when it is set by the operator The only time that this button is used in the password is as a factory default on new units Buttons which are used in normal MENU operation the MENU SELECT and ARROW buttons are not valid as password buttons All others are valid Once the correct password has been entered a main menu will be displayed showing each of the major sections that can be programmed by the operator In general the on screen prompts will be all that are needed to guide the operator through the steps to select and program the options Each screen prompts
31. plaze solamente con la misma bater a equivalente recomendada por el fabricante Deseche las bater as usadas de acuerdo con las instrucciones del fabricante Fuentes de Alimentaci n Externas Usar solo las fuentes de alimentaci n recomendadas Las fuentes de alimentaci n deben cumplir con los requisitos de la versi n m s reciente de la IEC 65 VDE 0860 El uso de substitutos puede da ar la unidad crear peligro de incendio o choque el ctrico CONTENTS I UNPACKING 5 2 SERVICE 5 3 DESCRIPTION saassaasasesemssssseness 5 4 INSTALLATION 5 al OWE kak y na n b a 5 4 2 Mounting 5 4 3 Cover Removal 6 4 3 D montage du Couvercle 6 4 3 Entfernung der Abdeckung 6 4 3 Desensamble de la Cubierta 6 44 Video Inputs KK KK KK 6 4 5 Monitor Outputs 6 4 6 Alarm Inputs and Output Accessory Output 7 4 7 Alarm inputs 7 48 Alarm Output 7 5 OPERATION 7 5 1 Menu Operation 7 5 2 Monitor Operation 8 5 3 Alarm Input Operation 0 6 ILLUSTRATIONS Il I UNPACKING Unpack carefully This is electronic equipment and should be handled care
32. r a un technicien sp cialis This label may appear on the bottom of the unit due to space limitations The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Warning To prevent fire or shock hazard do not expose units not specifically designed for outdoor use to rain or moisture En raison de limitation de place cette tiquette peut tre plac e sur le dessous de l appareil J Z N L clair fl ch dans un triangle quilat ral avertit l utilisateur de la pr sence d une tension dangereuse non isol e l int rieur de l appareil et d une valeur suffisante pour constituer un risque d lectrocution Le point d exclamation contenu dans un triangle quilat ral avertit l utilisateur de la pr sence dans la documentation qui accompagne l appareil de consignes d utilisation et de maintenance importantes Attention Pour viter le risque d lectrocution ou d incendie ne pas exposer la pluie ou l humidit un appareil non con u pour une utilisation ext rieure Attention Inst
33. tor is sequencing at the time that the video loss occurs the frozen image will be discarded when the monitor switches to a new sequence Video Loss Action 6 ILLUSTRATIONS page When that camera quadrant is next sequenced it will display a blank image with the video loss warning message Sequence lists are not automatically changed as a result of video loss Cameras with video loss can still be selected for display on the MON B monitor screen which will be blanked while that video loss input is selected but will still display the camera title time date and other status text Fd Termination Switches 4321 kK gt sal SI on Ul on WOL Si rl ooo EE LU N e E N Most components removed for clarity TC8278 Series is shown TC8277 Series has only one termination DIP switch 9505018BE Location of DIP SWitches TC8277 Series and TC8278 ON S9404002AE Front Panel TC8275 Series O i n Video 1 Video 2 r Camera 2 E S9404003AE Typical Application TC8275 Series PHILIPS on li lli Ha Front Panel TC8277 Series and TC8278 Series and Back Panel TC8277 Series Camera 2 Camera 3 Camera 1 Camera 4 Door Switch Additional Cameras Te Monitor B 75 Ohm Se WD ae a BS Pe 00000000 D Typical
34. uarter screen size and combines them to provide a monochrome or color quad display on a single monitor while retaining all color information The TC8275 Series has four terminated camera inputs and one monitor output A fixed color quad display is provided on the unit s monitor output with no on screen text or status indications It has no alarm inputs or other status I O and there are no front panel controls The full featured four channel TC8277 Series and eight channel TC8278 Series have looping camera inputs and a VCR input plus two monitor outputs Both monitor outputs have switching capability and both include on screen text display capability for camera ID and titles date and time and status indications Alarm inputs and status I O is provided The C8277 and TC8278 units are user programmable via on screen menus The TC8278 eight channel quad displays all eight reduced images on a single monitor by sequencing two paged color quad displays 4 INSTALLATION 4 I Power Model Rated Voltage Nominal Power No Voltage Range at Rated Voltage TC8275 120 VAC 50 60 Hz 108 to 132 15 W TC8275X 230 VAC 50 60 Hz 195 5 to 253 I5W TC8277 120 VAC 50 60 Hz 108 to 132 15 W TC8277X 230 VAC 50 60 Hz 195 5 to 253 I5W TC8278 120 VAC 50 60 Hz 108 to 132 15 W TC8278X 230 VAC 50 60 Hz 195 5 to 253 I5W The model number and operating voltage are shown on the bottom of the unit These units are supplied with grounded power cords grounding
35. y be equipped with a 3 wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 12 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords and plugs convenience receptacles and the point where they exit from the appliance 13 Power Lines An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outdoor system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal U S A models only refer to the National Electrical Code Article 820 regarding installation of CATV systems 14 Overloading Do not overload outlets and extension cords as this can result in a risk of fire or electric shock 15 Object and Liquid Entry Never push objects of any kind into this unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the unit l6 Servicing
Download Pdf Manuals
Related Search