Philips SQM5822 User's Manual
Contents
1. C UL US listed for weight capacity up to 132lbs 2 1 What s in the box 2 s Wall mount Cotter pin n NN BRAIN Her Bag 1 A M4x12 Bolt x4 B M4x30 Bolt x4 C M4 Lock Washer x4 RAN ENNE Bag 2 D M5x12 Bolt x4 E M5x30 Bolt x4 F M5 Lock Washer x4 mw Omm U J e Bag 3 G M6x12 Bolt x4 H M6x35 Bolt x4 I M6 Lock Washer x4 A BAM DNA U U T Bag 4 J M8x16 Bolt x4 K M8x40 Bolt x4 I M8 Lock Washer x4 Bag 5 M Small Spacer x4 N Large Spacer x4 O M6 Washer x4 gt mue CO Bag 6 P Concrete Anchor x6 Q M8x63 Lag Bolt x6 R Lag Bolt Washer x6 2 2 What you ll also need Phillips head screwdriver Ratchet or driver with 1 2 13 mm socket Portable or electric drill 1 4 6 mm drill bit and stud finder for drywall installation 3 8 10 mm masonry bit for concrete installation Stud finder 3 Installing your wall mount In this chapter the basic steps to get you started are described e Warning Carefully read the safety precautions in Section 1 Important before you install the wall mount 3 1 e Mounting the wall plate drywall Warning For safety reasons this mount must be secured to two adjacent wood studs at least 16 apart The studs must be capable of supporting t2. Register your product and get support at www philips com welcome SQM5822 27 EN Fixed wall mount PHILIPS Table of contents 1 Important 2 Your fixed wall mount 2 1 What s in the box 2 2 What you ll also need 3 Installing your wall mount 3 1 Mounting the wall plate drywall 3 2 Mounting the wall plate concrete 3 3 Attaching the arms to the display 4 Mounting and adjusting 5 Guarantee and service AR OQ U1 Ui Ui 1 Important Take time to read this manual before you use your wall mount It contains important information and notes regarding operating your wall mount 2009 Koninklijke Philips Electronics N V All rights reserved Reproduction in whole or in part is prohibited without the written consent of the copyright owner Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners A Warnings Make sure these instructions are read and thoroughly understood before attempting installation If you are unsure of any part of this installation contact a professional installer for assistance or contact Customer Service at 1 919 573 7854 This product has been designed for application on a vertical wall in commercial and residential buildings constructed of wood wall studs or masonary solid concrete brick and stone If you are unsure of your wall composition or for assistance with other surfaces contact a qualified installer This product is not d
3. and place it on the wall plate Do not release the display until the mounting arms have securely hooked onto the mount 6 wee a _ v mu Carefully hook the display onto the wall plate 7 e Warning Insert the safety bar at the center of the mount to avoid having the display accidentally knocked off the mount This MUST be done in order to secure the display to the mount NOTE A cotter pin included Is used to secure the arms to the mount OR a padlock not included can be inserted into the hole at the end of the saftey bar to help prevent theft of your display A small cotter pin can be used to secure your display to the mount included Once the tv is fitted properly on to the wall bracket the security bar must be put into place e Note Slide arm through slots in wall plate amp brackets Once the security bar is slid into the appropriate slots a lock not provided may be placed for additional security EA A small cotter pint can be used to secure your display to the mount included 9 O LON ES m l DYA 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount Call 1 919 573 7854 Limited One Year Warranty Philips warrants that this product shall be free from defects in material workmanship and assembly under normal
4. esigned for use on walls constructed of metal studs If you are unsure of your wall composition or for assistance with other surfaces contact a qualified installer The wall or mounting surface must be capable of supporting the combined weight of the mount and the display otherwise the structure must be reinforced Do not exceed the maximum load capacity of 132lbs for this product Fits 30 55 screens Safety gear and proper tools must be used Failure to do so can result in property damage and or serious injury A minimum of two people are required for this installation Do not attempt to install this mount alone under any circumstance Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display Consult the owner s manual for your display for more information This mount is equipped with a safety device that must be used whenever the mount holds a display Not using the safety device can cause property damage serious injury or death 2 Your fixed wall mount Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Designed to fit most TV brands with a focus on safety and ease of use Includes Easy 1 2 3 installation kit complete with all necessary hardware for mounting on different types of walls mounting templates and bubble level
5. he combined weight of the mount and display See enclosed mounting template for diagram and guide of how to mount properly on the wall Using a stud finder locate and mark two adjacent studs for securing the mount make sure your marks are in the center of each stud Note Once studs have been located you will need to verify with a hammer and a nail A Simply place the nail over your mark on the wall and tap in with hammer if the nail encounters resistance and is secure in wall you have verified a stud location B If it just pushes through with no resistance you will need to start over and locate the stud Using the enclosed mounting template place the diagram against the wall and mark four locations two per stud on the wall where the mount Is to be Installed Be sure to use the center of each stud With the help of another person place the mount against the wall and level it using the bubble guide While another person holds the mount in place mark four locations two per stud on the wall where the mount is to be installed Be sure to use the center of each stud these marks should line up with the ones made in step 3 above using the template Set the mount aside and drill a 1 4 6 mm pilot hole at each marked location Place the mount back against the wall and secure it using the lag bolts O and lag bolt washers R provided Do not over tighten these bolts and do not release the mount until all b
6. laster or drywall the concrete anchor must pass completely through the layer to rest flush with the concrete surface 3 3 Attaching the arms to the display A Warning Use extra care during this part of the installation Avoid laying your display face down if possible as it may damage the viewing surface El Examine the back of your television If the back of your display is flat You will be using one of the shorter bolts from the hardware kit 3 If the back of your display is curved or recessed You will be using one of the longer bolts and a spacer 4 Determine the correct diameter bolt to use by trying one bolt each from Bags 1 4 of the hardware kit Do not force any of the bolts if you feel resistance stop immediately to avoid damaging your display Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the corresponding lock washer C Fl or L You will need to use the M6 washers O if you are using the M4 M5 or M6 bolts If your display has a curved or recessed back you may also need to use a spacer M or N Make sure the screws are snug but do not over tighten 5 Pi 6 Tip Use a longer bolt and spacer for displays with curved or recessed backs Do not use the M washer O if you are using the M8 bolts J or K 4 Mounting and adjusting Ell With the help of another person carefully lift your display
7. olts are in place Once all 4 lag bolts are in place you must tighten each one note be sure not to over tighten 1 3 2 O Mounting the wall plate concrete Warning For safety reasons the concrete wall must be capable of supporting the combined weight of the mount and display See enclosed mounting template for diagram and use enclosed mounting template as a guide for precision mounting Using the enclosed mounting template place the diagram against the wall and mark six locations on the wall where the mount Is to be Installed With the help of another person place the mount against the wall and level it using the bubble guide While another person holds the mount in place mark six locations on the wall where the mount is to be installed Set the mount aside and drill a 3 8 10 mm pilot hole at each marked location Remove any excess dust from the holes Insert a concrete anchor P into each hole so that it is flush with the concrete surface A hammer can be used to lightly tap the anchors into place if necessary Place the mount back against the wall and secure it using the lag bolts O and lag bolt washers R provided Do not over tighten these bolts and do not release the mount until all bolts are in place 2 EN Once all 6 lag bolts are in place you must tighten each one Be sure not to over tighten e Note If the concrete wall is covered by a layer of p
8. use in accordance with the specifications and warnings for one year from the date of your purchase of this product This warranty extends only to the original purchaser of the product and is not transferable To exercise your rights under this warranty you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase For customer support or to obtain warranty service please call 1 919 573 7854 THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES Philips liability is limited to repair or at its sole option replacement of the product Incidental special and consequential damages are disclaimed where permitted by law This warranty gives you specific legal rights You may also have other rights that vary from state to state Register your product and get support at www philips com welcome PHILIPS 2009 Koninklijke Philips Electronics All rights reserved SQM5822 27 UM V2 0
Download Pdf Manuals
Related Search