Philips MAGNAVOX PR1913X1 User's Manual
Contents
1. PHILIPS Wc PR1910B1 PR1913X1 Owner s Manual Getting Started W arning Precautions Features Registration Hooking Up Your TV Antenna C able Connections 2 3 VCR Connections Auto Install Basic TV and Remote Control O peration Features Channel Edit Language Volume Sleeptimer SmartLock SmartLock Review SmartLock Access Code Picture Adjustments Closed Captioning General Information Glossary Tips W arranty Federal Communications Commission W arning Any unauthorized changes or modifications to this equipment void the user s authority to operate it For Customer Use Enter below the Serial N umber and the Model N umber of your television located on the back of the TV Keep this information for future reference This manual your new product and the packaging contain materials that can be recycled and reused Specialized companies can recycle your product to increase the amount of reusable materials and to min imize the amount that needs to be disposed properly Your product uses batteries that should not be thrown away when depleted but should be disposed as small chemical waste Please find out about the local regulations on disposal of your old product batteries manual and packaging whenever you replace existing equipment Copyright 2000 by Philips Consumer Electronics All rights reserved SmartLock is a trademark of Philips Consumer Electronics COLOR TELEVISION AND2. 3 Press the VOL ume gt or lt button to advance to the Channels Blocked screen All current ly blocked channels will appear Channels Blocked 07 18 32 e TV Y7 Appropriate for children seven and older TV G General Audience e TV PG Parental Guidance suggested e TV 14 Unsuitable for chil dren under 14 TV MA Mature audience only KO Preste VOL ume gt or lt button to advance to the Block Unrated and Block No Rating screen which shows if these options are set to On or Off Block Unrated On Block No Rating O ff After 10 seconds the main menu will reappear Repeat steps 2 4 as often as neces sary in order to review all the settings we When you are fin ished press the STA TUS EXIT button STOP FEATURES CONT D SMARTLOCK GEGIN Access CODE lt gt Pres the MENU but lt 2 gt eee O ae E o change the access code ton then press the tons to enter your old access enter your desired access code in o these steps CH annel A V buttons to code If you have never set up the New Code space Then enter select SmartLock Press your personal access code use the same code in the Confirm the VOL ume gt or lt 0711 Code space button to continue Your new access code should be You cannot 2 use the default code after you set up your personal access VOLUME mm gt Press the CH annel a recorded You will return to the code
3. SLEEPTIMER 0 SmartLock buttonsto select CHANGE SmartLock menu Smart ock REVIEW CODE Then press the To restore 0711 as VOL ume gt or lt button to ee your personal access continue PERS SB code unplug the TV s power cord for z dai 10 seconds then martLock BLOCK lug it in again T his oo ners gt Pres the STATUS EXIT N pz button EEEE D forget your personal Enter Your Access Code access code E PICTURE PU Oresme lt 2 gt presthevoLtuney lt 2 Prestre button then press the p gt lt buttons to adjust the STATUS EXIT button T o adjust your TV picture CH annel A V buttons to selected picture control controls select a channel select a control and follow these steps SETUP EXIT gt BRIGHTNESS Mittens 24 COLOR With 31 PICTURE Wh BRIGHTNESS Press the VO L ume lt buttons until the darkest parts of the picture are as bright as you prefer COLOR Press the VO L ume lt buttons to add or reduce color PICTURE Press the VO L ume gt lt buttons until the lightest parts of the picture show good detail SHARPNESS Press the VO L ume lt a buttons to improve detail in the picture TINT Press the VO L ume B lt buttons to obtain natural skin tones Eod EGIN SMART Si oe CAPTIONING Press the CC button Her NW losed Captioning allows repeatedly until the desired
4. Usually CAPTION 1 is the preferred Closed Caption mode Closed you to read the voice con Closed Caption mode CAPTION 1 or 2 Dialogue and descriptions for the Captions will be tent of television programs on appears on the screen action on the captioned TV program shows on the screen delayed briefly when the TV screen Designed to You may choose CAPTION 1 TEXT lor 2 A black box appears on the TV screen If the you mute or adjust help the hearing impaired this CAPTION 2 TEXT 1 TEXT 2 TEXT mode is available with the current TV program text or the volume change channels or press the STATUS EXIT button to see the current channel number feature uses on screen text or CAPTION OFF information will appear boxes to show dialogue and D CAPTION OFF Select to turn off Closed Captions com conversations while the TV pletely program is in progress Captions and texts may not match the TV voice broadcast Note Broadcast stations will exactly often use spelling abbrevia Interference or a weak antenna cable signal may cause the tions symbols dropouts and Closed Captioning system to function improperly other grammatical shortcuts in The caption or text characters will not appear if the menu is order to keep pace with the on the screen on screen action These factors Remember not all TV programs and commercials are broad vary with the source of the cast with Closed Captioning N either are all Closed Caption captioned text mat
5. REMOTE CONTROL Infrared Remote Control operates your TV and helps you set up on screen features Standard Broadcast VHF UHF or Cable TV CATV channel capability Closed Captioning allows you to read TV program dialogue as on screen text Auto Install quickly and easily selects sta tions available in your area Sleeptimer automatically turns off the TV at preset times Language Selection allows you to choose English or Spanish on screen menus This does not affect the language of Closed Captioning SmartLock lets you control what channels or programming can be watched If a pro gram s rating meets or exceeds the limit you select you must enter an access code before you can view the programming Automatic Shut Off turns off the TV after 15 minutes when it is on a channel that is not receiving a broadcast signal for exam ple if a station has gone off the air for the night This owner s manual is made of recycled paper Return your Warranty Registration card today to ensure you receive all the benefits you re entitled to Once your PHILIPS MAGNAVOX purchase is registered you re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product So complete and return the Warranty Registration Card enclosed with your purchase at once And take advantage of these important benefits Warranty Verification Registering your product within 10
6. contact your dealer Or call 1 800 851 8885 and refer to the fol lowing part num bers to order UHF VHF Combiner 4835 466 97016 75 3002 Adaptor M61009 300 75 Adaptor 4835 218 27003 HOOKING Up Your TV ANTENNA CABLE CONNECTIONS CONT D fe VCR To TV EGERN LD come your O Connect a coaxial lt 3 gt Refer to the VCR Basic CONNECTION oa or Cable e y e i the as cig owner s manual for other the IN FROM ANT enna jack on t ossible connections and for he basic Antenna Cable to p f IN jack on the TV shown here If you have a Cable Box refer to the VCR owner s manual for details The coaxial cable may be supplied with the VCR 300 to 75Q Outdoor Adaptor VHF UHF Antenna Coaxial cable G LS M AP IN FROM ANT OUT TO TV A O i yp L gt Ifyou do not have a O do not havea CABLE CABLE Box Cable Box then you re ready Cable Box connect the Vo Cable TV signal may be to connect your Cable TV sig Cable TV signal to the a single 75Q cable or a nal to the TV ANT enna IN jack on the TV Cable Box installation In either If you have a Cable Box If you have a Cable Box case the connection to the TV Connect the Cable TV signal Use a coaxial cable to connect is very easy to the IN jack on the Cable the OUT jack of the Cable Box Box to the AN T enna IN jack on the TV NOTE The coaxial cable might be
7. days con firms your right to maximum protection under the terms and conditions of your PHILIPS MAGNAVOX warranty Owner Confirmation Your completed W arranty Registration Card serves as verification of ownership in the event of product theft or loss Registration Returning your W arranty Registration C ard right away guarantees you ll receive all the information and special offers which you qualify for as the owner of your model Congratulations on your purchase and welcome to the family Dear PHILIPS MAGNAVOX product owner Thank you for your confidence in PHILIPS MAGN AVO X You ve selected one of the best built best backed products available today And we ll do everything in our power to keep you happy with your purchase for many years to come PHILIPS TENNA As a member of the PHILIPS MAGNAVOX family you re entitled to protection by one of the most comprehensive warranties and outstand ing service networks in the industry W hat s more your purchase guarantees you ll receive all the information and special offers for which you qualify plus easy access to accessories from our convenient home shopping network And most importantly you can count on our uncompromising commitment to your total satisfaction All of this is our way of saying welcome and thanks for investing in a PHILIPS MAGNAVOX product Sincerely lt gt Robert Minkhorst President and Chief Executive O fficer P S Rem
8. may last this limitation may not apply to you TO GET WARRANTY SERVICE IN CANADA Please contact Philips at 1 800 661 6162 French Speaking 1 800 363 7278 English Speaking In Canada this warranty is given in lieu of all other warranties No other warranties are expressed or implied including any implied warranties of merchantability or fitness for a par ticular purpose Philips is not liable under any circumstances for any direct indirect special incidental or consequential damages howsoever incurred even if notified of the possibility of such damages REMEMBER Please record below the model and serial numbers found on the product Also please fill out and mail your warranty registration card promptly It will be easier for us to notify you if necessary MOD ELH na ile pees Oka at markets Sand 528 ented te pide kta N SERIAL Philips Service Solutions Group P O Box 2976 Longview Texas 75606 903 242 4800
9. on premium cable channels and Emergency Broadcast System signals then denies access to programming if the program s rating meets or exceeds the limitations you select To block specific ratings or channels fol low these steps access code see SmartLock Access Code on page 7 If the Incorrect Access Code mes sage appears after step 2 enter the cor rect access code In order to protect the privacy of the access code an X will appear on the screen instead of the num ber you enter A CHANNEL XX BLOCKED mes sage will appear when someone tries to access the blocked programming If you want to view this programming enter your access code The channel will remain blocked until you enter the cor rect code If you do not know the code you will have to select another chan nel using the CH annel a v but tons W hen you turn off the TV once the programming is blocked again x SMARTLOCK REVIEW o check your SmartLock settings follow these steps You will know what types of programming and which chan nels are blocked from viewing If you do not use the VO L ume gt or lt button to advance through the SmartLock REVIEW screens the screens will advance automatically within 10 seconds lt gt Pres the MENU L gt Use the Number but button then press the tons to enter your 4 digit CH annel A V buttons to access code The default code select Smart
10. select channels e Cable Users Enter channel numbers as a two digit number for the quickest results For example to select channel 6 press 0 6 If you only press the Number 6 button channel 6 will be selected after a brief delay There also may be a brief delay when you select channels 10 11 and 12 If you want to select channels 100 and above enter channel numbers as a three digit number For example to select channel 117 press 1 1 7 e Antenna Users Enter channel numbers as a two digit number for the quickest results You may only select channels 2 69 For example to select channel 5 press 0 5 If you only press the Number 5 button channel 5 will be selected after a brief delay VOL ume gt lt Buttons Press to adjust the TV sound level Press to adjust an item in the on screen menu or to advance to the next menu MUTE Button Press to turn OFF the sound on the TV Press again to restore the sound STATUS EXIT Button Press to see the current channel number on the TV screen Press to remove the on screen menu You also may remove the menu by press ing the CH annel A V buttons to select EXIT then pressing the VO L ume B gt lt d buttons You may need to select EXIT repeatedly to completely remove all of the menus ALT CH Alternate Channel Button Press to return to the TV channel you were viewing immediately before switch ing to your current channel CC Closed Caption Butto
11. CH anne A V buttons to select AUTO INSTALL Then press the VOL ume gt or lt button to enter AUTO INSTALL which will set up the channels S gt Press the CH annel A F buttons to select SETUP Then press the VOL ume gt or lt button to continue EXIT LANGUAGE AUTO INSTALL SETUP CHANNEL EDIT EXIT BRIGHTNESS WHNNinan COLOR 1 PICTURE Tn lt gt Pres the POWER button to turn ON the TV lt 2 gt Press the MENU bur ton The main menu appears on the TV screen AUTO STORE Jitu 1 W hen setup is complete the SETUP menu will appear for a moment then the lowest stored channel will be selected N ow when you press the CH annel A V buttons you will only scan through channels that have been memorized and are available MENU STATUS EXIT MUTE BEGIN gt Point the remote contro toward the remote sensor on the TV when operating the TV with the remote SLEEP Button Press to set the TV to turn itself O FF automatically Details are on page 5 CH annel 4 Buttons Press to scan through available channel numbers Press to select an item in the on screen menu POWER Button Press to turn the TV ON and OFF MENU Button Press to access the on screen menu Press the CH annel A V buttons to select an item in the menu Press the VOL ume lt 4 buttons to adjust an item in the menu or to advance to the next menu Number Buttons Press to
12. Lock Then is 0711 If you have not set up press the VOL ume gt or your personal access code you lt button to continue should use 0711 gt If you selected Blocking O ptions at step 4 SmartLock VOLUME LTTE SLEEPTIMER 0 SmartLock SmartLock REVIEW SETUP Enter Your Access Code Press the CH annel 4 buttons to select Master Disable Block Unrated or Block No Rating Then press the VOL ume gt or lt button to select ON or OFF To return to the main BLOCK menu press the MENU button BLOCKING OPTIONS bm Master Disable O FF Block Unrated O FF Block No Rating O FF If you selected C hannels Blocked at step 4 Channel will be selected Press the VOL ume gt or lt button or use the Number buttons to select the channel you want to block Press the CH annel A V buttons to select Blocked then press the VOL ume gt or lt button to select ON or OFF If Blocked is ON the channel can not be watched until the viewer enters the access code To reset all channels for viewing press the CH annel A V buttons to select Clear All then press the VO L ume or lt button Channel will be selected again Remember viewing could still be blocked by another SmartLock setting such as Movie Ratings To return to the main BLOCK menu press the MENU button CHANNELS BLOCKED gt Channel 1 Blocked 0 FF Clear All If you selected M ovie Ratings or Parental G
13. T button lt gt Pres the CHlanne A V buttons to select SKIPPED Then press the VOL ume gt or lt button to set SKIPPED to YES if you want to skip past the channel when using the CH annel A F but tons or NO if you want the channel to be available when you are using the CH annel A F buttons lt I Press the STATUSIEXIT button when you are finished If you accidentally 2 chose Spanish and need English 1 Press the MENU but ton 2 Press the CH annel A V buttons to select INSTALACION then press the VO L ume b gt or lt button to continue 3 IDIOMA will be select ed Press the VO L ume gt or lt button to have ENG appear beside LAN GUAGE 4 Press the STATUS EXIT button VOLUME 5 Ld MART ely here are two ways to adjust Press the MENU but lt 2 Press the CH annel L gt Press the HELP R the TV s volume Follow fton A F buttons to select STATUS EXIT button to a these steps to adjust the volume VOLUME Then press the remove the menu The Volume Z using the on screen menu VOL ume gt lt buttons to indicator should appear Or you can adjust the volume adjust the volume level on the screen when using the VOL ume P a but tons on the remote control or the VOLUME buttons on the TV you adjust the volume SHARPNESS J00HEumn 34 TINT wuaqqenn 05 VOLUME 1 LTT 13 SLEEPTIMER OFF SmartLock gt The simplest wa
14. TV 14 category SLEEPTIMER SmartLock SmartLock REVIEW SETUP EXIT VVVVS Movie Ratings R NC 17 X Parental Guidelines S gt BLOCK will be selected Press the VOL ume gt or lt button to continue SmartLock gt BLOCK CHANGE CODE gt Press the STATUS EXIT button L Press the CH annel A V buttons to select Blocking Options Channels Blocked Movie Ratings or Parental Guidelines Then press the VOL ume gt or lt but ton to continue BLOCK gt Blocking O ptions Channels Blocked Movie Ratings Parental Guidelines D Master Disable W hen Master Disable is ON all settings of Channel Blocked BLOCKING OPTIONS Movie Ratings Parental Guidelines Block Unrated and Block No Rating are ineffective SmartLock DISABLED will appear when you look at SmartLock Review All programming may be viewed Block Unrated W hen Block Unrated is ON TV programs are blocked when the show is broadcast as Unrated Block No Rating W hen Block No Rating is ON TV programs are blocked when the show is broadcast without rating information PARENTAL GUIDELINES RATING EXPLANATIONS e V Violence e S Sexual situations L Language e D Inappropriate dialogue e FV Fantasy Violence may frighten children under seven TV Y7 category only Some cartoons may have this rating e TV Y Appropriate for all children
15. ee but you pay for all labor charges From One to two years from the day of purchase you pay for the replacement or repair of all parts except the picture tube and for all labor charges After two years from the day of purchase you pay for the replacement or repair of all parts and for all labor charges All parts including repaired and replaced parts are covered only for the original warranty period When the warranty on the product expires the warranty on all replaced and repaired parts also expires WHAT IS EXCLUDED Your warranty does not cover e labor charges for installation or setup of the product adjustment of customer controls on the product and installation or repair of antenna systems outside of the product product repair and or part replacement because of misuse accident unauthorized repair or other cause not within the control of Philips Consumer Electronics Company reception problems caused by signal conditions or cable or antenna systems outside the unit e aproduct that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed manufactured approved and or autho rized or repair of products damaged by these modifications e incidental or consequential damages resulting from the product Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you This includes but is not limited t
16. ember to get the most from your PHILIPS MAGNAVOX product you must return your W arranty Registration Card within 10 days So please mail it to us right now A This bolt of lightning indicates uninsulated material within your unit which may cause an electrical shock For the safety of everyone in your household please do not remove product covering A The exclamation point calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE CAUTION To prevent electric shock match wide blade of plug to wide slot and fully insert ATTENTION Pour viter les choc lectriques introduire la lame la plus large de la fiche dans la borne cor respondante de la prise et pousser jusqu au fond Know these ymbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL PHILIPS Visit our World Wide Web Site at http vww philipsmagnavox com 1B8202E001 OEMN 01685 L1105UF L1106UG ezz Printed in Malaysia 1 HOOKING Up Your TV ANTENNA CABLE CONNECTIONS ComBINATION UHF VHF poe antenna receives normal broadcast channels VHF 2 13 and UHF 14 69 Your connection is easy since there is only one 75Q oh
17. erial and do _ modes necessarily being used by a broadcast station during not indicate a need for TV ser LONS AN the transmission of a program Refer to your area s TV pro vice O gram listings for the stations and times of shows with Closed Captioning If a black box appears on the screen you have selected TEXT 1 or TEXT 2 To remove the black box select CAPTION 1 CAPTION 2 or CAPTION OFF cc Lo MENU STATUS EXIT MUTE Coaxial Cable A single cable with a metal connector that screws or pushes direct Programming Adding or deleting channels in the television s memory The televi ly onto a 75Q jack AN T enna In jack on the Television or VCR sion remembers only the locally available or desired channel numbers and skips over any unwanted channel numbers Display Allows the user to quickly confirm what channel number is being viewed currently Remote Sensor A window or opening on the front of the TV through which Jack Panel The area on the back of the TV remote control signals are received Menu An on screen listing of features that are available for adjustments Tuin LESA Wire TNE UNDE rand ntanna nei ue ne mangi and f outdoor antenna systems In many cases this type of antenna wire requires an addition On screen Displays OSD The wording or messages that help you set up features al adaptor or balun in order to connect to the AN T enna In jack on the TV color adjustment channel
18. its in both places Movie Ratings and Parental Guidelines Company has determined that this Ratings will remain blocked even after a power failure product meets the ENERGY STAR L Remote Doesn t Work guidelines for energy efficiency En ERGY STAR is a U S registered mark Using products with the ENERGY STar label can save energy Saving energy reduces air pollution and lowers utility bills Duty Zinc Chloride or Alkaline batteries if necessary on the TV e Check the TV power cord e Check batteries Replace with AA Heavy Clean the remote and the remote sensor You cannot access the menu when the CHANNEL XX BLOCKED message appears If you enter the access code once you may change channels without see ing the CHANNEL XX BLOCKED message again If you turn off the TV power you will be asked for the access code again when you tune to a blocked channel If a power failure occurs the default code 0711 will be the active access code again If you connect the power cord to an AC outlet that is controlled by a wall Power Failure e W hen you disconnect the power cord from the AC outlet or if you have a power failure the Sleeptimer will be cancelled You Wrong Channel Repeat channel selection TV memory See page 5 for details e Add desired channel numbers into the switch your personal access code will be erased every time you turn off the p
19. m antenna jack on the back of your TV and that s where the antenna goes Combination VHF UHF Antenna O utdoor or Indoor SEPARATE UHF VHF ou may have two separate antennas One antenna is for VHF channels 2 13 and the other antenna is for UHF channels 14 69 For homes with separate UHF VHF antennas you will need an optional combiner before you can connect the antennas to the TV Outdoor UHF Antenna Twin lead 300Q Outdoor VHF Antenna Twin lead 300Q Outdoor VHF Antenna Round cable 75Q round connector 750 then you re ready to connect it to the TV If your antenna has flat twin lead wire 3000 you first need to attach the antenna wires to the screws on a 300 to 75Q adaptor Q gt If your antenna has a Twin lead W ire Round Cable 75Q lt gt Attach the separate UHF and VHF antennas to the correct screws on the combiner 75 300Q Adaptor Q gt Push the round end of the adaptor or cable onto the ANT enna IN jack on the back of the TV If the round end of the adaptor or cable is threaded screw it down tight 300 to 752 Adaptor combiner onto the ANT enna IN jack on the back of the TV U V Combiner lt 2 gt push the round end ofthe a7 Tosetthe 2 TV to select only the channel num bers in your area see Auto Install on page 4 Toorder 2 any optional accessory
20. n Press repeatedly to select a Closed Caption mode Details are on page 7 E gt Press the MENU button to display the TV s on screen menu Press the CHANNEL A V buttons to select an item in the menu Press the VOLUME A V but tons to adjust an item in the menu or to advance to the next menu Note To remove the menu press the CHANNEL A F but tons to select EXIT Then press the VOLUME Aor button You may need to select EXIT repeatedly to completely remove all of the menus Or press the MEN U button repeatedly if necessary to remove the MENU D lt 2 gt Press the VOLUME A V buttons to adjust the sound level gt pressthe POWER button to turn ON the TV Be sure to connect the TV power cord to a standard AC outlet The current channel number will appear briefly when the TV is first turned ON and with channel changes To display the channel number for five sec onds press the STA TUS EXIT button S gt Press the CHAN NEL A V buttons to select available TV chan nels You can turn on the TV by pressing the CHANNEL A buttons on the front of the TV The CH annel A but tons of the remote control will not turn on the TV power FEATURES CHANNEL EDIT UTO INSTALL see page 4 memorizes all the channels on your Antenna or Cable TV system CHANNEL EDIT makes it easy for you to add other channels or drop unwanted channels fr
21. o prerecorded material whether copyrighted or not copyrighted e a product used for commercial or institutional purposes WHERE IS SERVICE AVAILABLE W arranty service is available in all countries where the product is officially distributed by Philips Consumer Electronics Company In countries where Philips Consumer Electronics Company does not distribute the product the local Philips service organization will attempt to provide service although there may be a delay if the appropriate spare parts and technical manual s are not readily available MAKE SURE YOU KEEP Please keep your sales receipt or other document showing proof of purchase Attach it to this owner s manual and keep both nearby Also keep the original box and packing material in case you need to return your product BEFORE REQUESTING SERVICE Please check your owner s manual before requesting service Adjustments of the controls dis cussed there may save you a service call TO GET WARRANTY SERVICE IN U S A PUERTO RICO OR U S VIRGIN ISLANDS Contact a Philips factory service center see enclosed list or authorized service center to arrange repair In U S A Puerto Rico and U S Virgin Islands all implied warranties including implied war ranties of merchantability and fitness for a particular purpose are limited in duration to the duration of this express warranty But because some states do not allow limitations on how long an implied warranty
22. om the TV s memory MENU LANGUAGE por these steps to change the language of the on screen menus STATUSIEXIT lt gt Press the MENU but ton then press the CH annel A V buttons to select SETUP SmartLock SmartLock REVIEW SETUP EXIT BRIGHTNESS 000iuun 24 MUTE Press the MENU but ton SETUP EXIT BRIGHTN ESS COLOR 1 PICTURE Tica lt 2 Press the VOL ume gt or lt button to continue to the SETUP menu lt S gt Pres the CH annel A V buttons to select CHANNEL EDIT AUTO INSTALL CHANNEL EDIT EXIT LAN GUAGE lt Q Press the CH annel A V buttons to select SETUP then press the VOL ume gt or lt button to continue LANGUAGE will be selected EXIT LANGUAGE AUTO INSTALL CHANNEL EDIT A gt Press the VOL ume gt or lt button to continue to the CHANNEL EDIT menu CHAN NEL will be selected EXIT gt CHANNEL SKIPPED gt While CHANNEL is selected press the VOL ume gt or lt button or the Number buttons to select the channel you want to add or skip EXIT Bm CHANNEL SKIPPED S gt Press the VOL ume gt or lt button to select ENG for English menus or ESP for Spanish menus EXIT LANGUAGE AUTO INSTALL CHANNEL EDIT SALIDA IDIOMA ESP AUTO PROGRAMACION REVISAR CANAL L gt Press the STATUS EXI
23. ower at the wall switch The default code will be the active code again To restore 0711 as your personal access code unplug the TV s power may reset the Sleeptimer Access Code ALT CH Button Antenna Connections 2 3 Auto Install Batteries Cable TV Connections 3 Channel Edit Channel Setup hal NDEX CH annel A V Buttons Closed Captioning Coaxial Cable Controls Remote Controls TV Earphone jack Features Glossary Language MENU Button MUTE Button Precautions WARRANTY N umber Buttons Picture Adjustments PO WER Button Remote Control cord for 10 seconds then plug it in again Remote Sensor Review SmartLock Safety N otes Service SLEEP Button Sleeptimer SmartLock STATUS EXIT button VCR Connections Volume VO L ume B lt Buttons 4 5 W arranty COLOR TELEVISION 90 Days Free Labor One Year Free Replacement of Parts Two Years Free Replacement on Color Picture Tube This product must be carried in for repair WHO IS COVERED You must have proof of purchase to receive warranty service A sales receipt or other docu ment showing that you purchased the product is considered proof of purchase WHAT IS COVERED W arranty coverage begins the day you buy your product For 90 days thereafter all parts will be repaired or replaced free and labor is free From 90 days to one year from the day of purchase all parts will be repaired or replaced fr
24. setup etc Volume Indicator Appears on the TV screen when you adjust the volume GENERAL INFORMATION ins GES No Power Cleaning and Care e Unplug the TV before cleaning e Avoid using anything abrasive that could scratch the screen e W ipe the TV screen with a clean cloth dampened with water Gently wipe cabinet surfaces with a clean cloth or sponge dampened with TROUBLESHOOTING e Check the TV power cord l e Make sure the power outlet is not on a lease make these simple wall switch checks before calling for ser vice These tips can save you lt 2 No Sound time and money since charges for TV installation and adjust ment of customer controls are e Check the VO L ume B lt buttons e Check the MUTE button cool clear water Use a clean dry cloth to dry the wiped surfaces Occasionally vacuum the ventilation holes or slots in the cabinet back e Never use thinners insecticide sprays or other chemicals on or near the cabinet not covered under your wn o Picture warranty ae As an ENERGY STAR IE Partner Philips rerh p j C oncumer Electronice ANT enna IN jack on the TV e Check antenna cable connections Is the antenna or cable properly secured to the SmartLock Programming may be rated by the Motion Picture Association of America MPAA or according to the Television Parental Guidelines In order to block any inappropriate programming set your lim
25. supplied by the Cable TV company Note to the Cable TV System Installer This reminder is provided to call the Cable TV system installer s attention to Article 820 40 of the N ational Electrical Code which provides guidelines for proper grounding in particular specifying that the cable ground shall be connected to the ground ing system of the building as close to the point of cable entry as possible Cable TV Signal 75Q Cable TV C a E S Coaxial cable Cable Box Back of TV Back of TV To select Z only the channels on your Cable system see Auto Install page 4 If you use a Cable Box set the TV to the same channel as the CH 3 4 switch on the back of the Cable Box and select channels at the Cable Box SETTING UP AND USING YouR TV AUTO INSTALL Fo these steps to quickly add area channels into the TV s memory T o load the batteries into the remote L Slide off the battery compartment lid on the bottom of the remote control 2 Insert two AA batter ies supplied into the battery compartment as indicated inside the compartment Batteries installed incorrectly may damage the remote con trol 3 Replace the lid Battery Compartment Lid Note You can connect earphones not supplied to the EARPHONE jack on the front of the TV for private personal listening 4 gt Press the
26. uidelines at step 4 Press the CH annel A V buttons to select the rating you want to block Then press the VOL ume gt or lt 4 button so that ON appears beside the rating For example if you set PG to ON you may not view PG program ming because the block is on Programs with a PG or higher rating will be blocked MOVIE RATINGS G PG PG 13 PARENTAL GUIDELINES gt R e More specific sub ratings are available for TV Y7 TV PG TV 14 and TV MA W hen you press the VO L ume B gt lt 4 buttons to select TV Y 7 TV PG TV 14 or TV MA additional sub ratings will appear Press the VOL ume gt or lt button to set the main rating to ON Then press the CH anne A V buttons to select a specific sub rating Then press the VOL ume gt lt 4 buttons so that ON appears beside the sub rating If you select the main rating and turn it on or off the sub ratings will turn on or off automatically But you can always turn sub ratings on or off by selecting them individually You can only turn on a sub rating for example D if the main rating such as TV PG is set to ON lt gt Pres the MENU but 27 ile dea ton then press the the SmartLock settings for CH annel 4 buttons to Movie Ratings and Parental select SmartLock Guidelines appear REVIEW k Ratings that are blocked will appear on the screen An X will appear if a specific sub rat ing is blocked such as V for Violence in the
27. y to adjust the volume is by pressing the VO L ume b gt lt 4 buttons SLEEPTIMER H ave you ever fallen asleep Does the SLEEP button T h J in front of the TV only to o see how Z repeatedly to pick the amount of time 15 minutes to 120 minutes before the TV turns itself off The length of time will appear on the screen O ne minute before the TV shuts itself off the seconds will count down on the screen A Press the MENU button many minutes remain before the TV shuts itself off press the SLEEP button once or press the STATUS EXIT button have it wake you up at 2 a m with a test pattern screeching in your ears W ell your TV can save you all that trouble by automatically turning itself off Set the Sleeptimer simply by pressing the SLEEP button or you may use the on screen menu MENU s T MUTE To cancel a SLEEPTIMER setting press the SLEEP but ton twice so that O FF appears on the screen S gt Press the VO L ume lt buttons repeatedly to set the amount the time or to select O FF L rex the STATUS EXIT button to remove the menu lt 2 Press the CH annel A V buttons to select SLEEP TIMER FEATURES CONT D SMARTLOCK ge enables parents to prevent their children from watching inappropriate material on TV SmartLock reads the ratings for programming except for news and sports programs unedited movies
Download Pdf Manuals
Related Search