Philips iColor Cove QLX User's Manual
Contents
1. 01 Accessories for iColor Cove OLX Fixtures iColor Cove QLX fixtures are part of a low voltage system made up of the fixtures and e One or more compatible power supplies from the list below e One leader cable to connect each power supply output port to a series of fixtures e A Philips Color Kinetics or other DMX51 2 based controller work with iColor Cove QLX fixtures The number of lights that can be addressed varies with each controller For information on Philips or Color Kinetics controllers see http www colorkinet ics com support systemguide SysMatrix pdf Item Number Power Supply Compatible Philips and Color Kinetics power supplies sPDS 60ca24V provides 60W output 09 00002 02 that can be split between two ports DMX Ethernet PDS 60ca provides 60W output that can 109 0000 I 6 00 be split between two ports Preprogrammed or 109 000016 01 DMX sPDS 480ca 24V provides eight 60W output ports 09 000026 00 Leader Cable Item Number 30 foot 9 1 m leader cable 108 0000 1 5 00 Depending on the installation s design you may need optional jumper cables to add space between fixtures Optional mounting tracks ensure straight runs of fixtures Item Number 08 000020 00 08 000020 0 Item Description One foot 30 5 cm jumper cable Five foot 1 5 m jumper cable Box of 25 four foot 1 2 m mounting tracks for straight runs 523 000006 00 Philips Solid State Lighting2. The Fixtures and Accessories Carefully inspect the cartons and boxes containing the iColor Cove QLX fixtures the fixtures themselves and all cables for any damage that may have occurred in transit WARNING DO NOT USE A FIXTURE IF THE LENS HOUSING OR POWER CABLES ARE DAMAGED FIXTURES HAVE NO USER SERVICEABLE PARTS DO NOT ATTEMPT TO OPEN THEM 5 Install Mounting Tracks Optional If the optional mounting tracks are used install them now Tracks can be easily cut to fit with a hacksaw or nippers Make sure the tracks are firmly attached to the substrate with screws or other suitable connec tors in all mounting holes The screw heads may not rise above the interior rails OK Figure Mounting Track Detail 6 Install The Fixtures See iColor Cove QLX Wiring on page 4 for an overview of these steps Position the first fixture in the series If a track is used snap the fixture into the track and slide it into position The leader cable will connect to this fixture s male connector so make sure that the fixture is installed so that the next fixture can plug into this fix ture s female connector 2 Use four screws to secure the fixture Most materials will require pilot holes for the screws Mark the location of the holes using the fixture base as a guide Drill the pilot holes through the track if used and mount the fix ture with four 6 screws 4 Position the next fixture i
3. 01 6 340 868 6 636 003 6 777 891 6 969 954 6 975 079 7 038 399 7 161 313 7 186 003 7 202 613 7 221 104 and 7 233 115 Other patents pending Copyright 2008 Philips Solid State Lighting Solutions All rights reserved Chromacore Chromasic CK the CK logo Color Kinetics the Color Kinetics logo ColorBlast ColorBlaze Color Burst ColorCast ColorPlay DIMand Direct Light EssentialWhite eW iColor iColor Cove IntelliWhite iW iPlayer Light Without Limits Optibin Powercore QuickPlay Sauce the Sauce logo and Smartjuice are either regis tered trademarks or trademarks of Philips Solid State Lighting Solutions in the United States and or other coun tries All other brand or product names are trademarks or registered trademarks of their respective owners PUB 000 85 00R03 2 29 08
4. Installation Guide IColor Cove OLX CK INTELLIGENT SERIES Preliminary iColor Cove QLX is a compact linear fixture that generates saturated color and dynamic effects in alcoves accent areas and other interior spaces The fixture is available with a wide 120 x 120 or medium 100 x 40 beam An integrated rotating bracket and optional mounting track provide precise positioning and end to end connections ensure a simple installation e Integral mounting bracket with 80 rotation e 50 000 hour lifetime e 24 VDC input power e End to end connectors e Two standard lengths 6 inch 15 2 cm and 12 inch 30 5 cm e Uniform light quality is ensured with Optibin technology e Precise cost efficient digital control is provided by Chromasic technology PHILIPS Scope Of This Guide This Installation Guide contains important information on planning and installing your new iColor Cove QLX fixture to ensure peak perfor mance Read it carefully and save it for future reference This docu ment should never be considered a substitute for any provision of a regulation or state and or local code The iColor Cove QLX product line includes and this Installation Guide covers these products iIColor Cove OLX Item Numbers Fixture Length Item Number Beam Angle 6 15 2 cm Wide 120 x 120 101 000066 02 Medium 100 x 40 101 000066 03 12 30 5 cm Wide 120 x 120 101 000066 00 Medium 100 x 40 101 000066
5. Solutions iColor Cove QLX Installation Guide Start Here Before you begin the installation read all of this installation guide iColor Cove QLX fixtures are low voltage fixtures that require a pow er supply and a controller to be fully functional Control signals can be generated from any DMX compatible control ler but only the power supplies listed on the previous page can trans mit the control signals on the fixture s leader cable Owner User Responsibilities It is the responsibility of the contractor installer purchaser owner and user to install maintain and operate the iColor Cove QLX fixture in such a manner as to comply with all federal state and local laws codes ordinances and regulations WARNING FIXTURES MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL NATIONAL AND LOCAL ELECTRICAL CODES AND REGULATIONS 2 Prepare For Ihe Installation Planning the installation includes developing a layout plan and verifying that equipment required to support the lights is in place as well as ensuring that all required additional components mounting tracks power supplies leader and jumper cables are available If approved architectural drawings are not available e Create a layout plan that starts with the location of the power supplies and includes all power supplies leader cables fixtures and jumper cables e Refer to national local and state codes and consult with the appro
6. em 08 000020 00 and five foot 1 524 m Item 108 000020 Ol Scope Of This Guide 3 Assemble Additional Items To wire and mount an iColor Cove QLX fixture you may need addi tional parts and tools Power Supplies and Wiring Install all power supplies including any interfaces with controllers before installing the iColor Cove QLX fixtures One iColor Cove QLX leader cable is required to connect each run or series of fixtures to a power supply port The power supply and external controllers send control signals to the iColor Cove QLX fixtures over the leader cable To configure the power supply fixture connection you will need the power supply installation or user guide for specific instructions If jumper cables are required to add space between fixtures make sure that they are available Mounting Tracks iColor Cove QLX fixtures can be mounted directly to a wall ceiling cabinet or other secure surface For straight linear applications several iColor Cove QLX fixtures may be snapped into an optional four foot long mounting track to ensure a straight run If the track is specified in the plans make sure it is available Tools and Supplies You will need these tools and supplies e General tools to secure fixtures and mounting tracks drill screw driver level measuring tools etc e 6 mounting screws or other hardware bolts nuts and washers for instance that is appropriate for the substrate 4 Inspect
7. n the series Match its male connector to the female connector of the previous fixture Snap it into the track if used and secure the fixture with four mounting screws 5 Continue mounting the fixtures making direct connections or inserting jumper cables as you go until all lights in the series are mounted and connected 6 Insert the terminator packaged with the leader cable into the last fixture of the series 7 Make Electrical Connections Verify that power in the line circuit to the power supply is OFF or that the power supply s power cord is not connected 2 Connect the leader cable to the first fixture in the run or series 3 Connect the leader cable to the power supply NIN ANI Ne ENSURE THAT MAIN POWER SUPPLY IS OFF BEFORE INSTALLING OR WIRING A FIXTURE 4 Energize the power supply s line circuit It is normal for some fixtures not to illuminate because communi cations between the power supply and fixtures has not been set up http www colorkinetics com 4 iColor Cove QLX Installation Guide Figure 2 iColor Cove QLX Wiring This illustration shows the power supply receiving line power and control data inputs and dispatching both power and data through a lead er cable to the first fixture in a run Note the terminator location in the last fixture of the run 8 Address Fixtures With the Power Supply To power up the fixtures each one needs to be assigned a unique addressed by the power
8. priate electrical inspector to ensure compliance with all applicable codes and regulations e Consult Color Kinetics Application Engineering Services as needed at support colorkinetics com Use these guidelines when you plan the installation e One iColor Cove QLX leader cable is required to connect each run or series of fixtures to a power supply port e The number of iColor Cove QLX fixtures that may be daisy chained together in a run is determined by the output of the power supply and its ports Each of the compatible power sup plies listed in Accessories for iColor Cove QLX Fixtures on page 2 provides one or more 60 Watt output ports So for example a single 60 Watt port can drive up to 30 6 inch or 20 2 inch iColor Cove QLX fixtures in a single series Or two shorter runs can be powered by two lower wattage ports A mix of fixture sizes may be used so long as the total power draw is less than the 60 W supplied by the power supply port e Ensure that the power supplies provide the required wattage to drive the fixtures and that the number of free ports is adequate e The power supply and first fixture may not be separated by more than the 30 foot 9 1 m length of the leader cable e Joined directly together two fixture s connectors allow for 25mm spacing between fixtures and 80 turns e When fixtures need to be separated by more than an inch use a jumper cable Two lengths are available one foot 30 48 cm It
9. supply The exact method used to address iColor Cove QLX fixtures depends on the type of power data supply being used Specific instructions are in each power supply s user guide or if an external controller is used in that tools guide e For information on the PDS 60ca 24V refer to the PDS 60ca 24V Installation Guide e For information on addressing see the sPDS 60ca 24V User Guide e The PDS 480ca uses external software either Light System Man ager or Video System Manager to address the fixtures 9 Aim The Fixtures Aim the fixtures by rotating each fixture to the correct angle There are detents every 0 degrees in the bracket that hold it in position CAUTION ICOLOR COVE QLX FIXTURES ARE A CLASS 2 LED PRODUCT DO NOT STARE INTO A BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Philips Solid State Lighting Solutions iColor Cove QLX Specifications Specifications are subject to change without notice 6 Inch Fixture 2 Inch Fixture Length 6 inches 15 2 cm 2 inches 30 5 cm Width 25 inches 3 2 cm tube diameter Height 37 inches 3 5 cm Weight 3 oz 85 g 5 oz 142 g LEDs Per Fixture 5 each red green and blue O each red green and blue Total Output lumens TBD Wide 120 x 120 beam angle 49 8 Medium 100 x 40 beam angle 46 Efficacy Lm W TBD White gt I5 Source High brightness LEDs Color Range 16 7 million 8 bit additive RGB colors con
10. tinuously variable intensity Beam Angle 120 x 120 or 100 x 40 Mixing Distance Mixing distance to uniform light is 2 inches 5 cm Housing Charcoal gray UL recognized injection molded plastic Lens Clear polycarbonate V 0 flame rating Fl UV rating Medium Beam Optics Polycarbonate Environment UL Dry CE IP20 Fixture Connectors IEC 15 A max with Cl3 plug Max Fixture Run 30 fixtures on a single 60VWV power supply port 20 fixtures on a single 20W power supply port Max Cable Run Length 30 feet 9 1 m Listings CE PSE RoHS UL CUL WEEE Control Chromasic input data Operating Voltage 24 VDC from a Philips or Color Kinetics DMX In Chromasic Out power supply Power Consumption 2 W maximum at full output steady state 3 W maximum at full output steady state Temperature Range 4 F to 22 F 20 C to 50 C operating temperature Humidity Range 0 to 95 non condensing LED Source Life 50 000 hours based on LED manufacturers test data http www colorkinetics com iColor Cove QLX Installation Guide PHILIPS Philips Solid State Lighting Solutions 3 Burlington Woods Drive Burlington MA USA 01803 Toll Free 888 385 5742 Tene 7 423 97977 Fax 617 423 9998 http www colorkinetics com CE LISTED CHROMASIC BY COLOR KINETICS OPTIBIN BY COLOR KINETICS This product is protected by one or more of the following U S patents and their foreign counterparts 6 016 038 6 150 774 6 292 9
Download Pdf Manuals
Related Search