Philips DP 6000 User's Manual
Contents
1. DP 6000 DIGITAL PAGING SYSTEM FIELD CONTROL PANEL INSTALLATION INSTRUCTIONS 1 GENERAL INFORMATION For a detailed description of D P 6000 paging calls refer to Installation Instruction N o 63 for the High Performance Control Desk LBB 5800 L1 Description Philips Personal Security System PS 6000 combines paging functions with portable alarm facilities for people on the move in hazardous environments or are liable to incur some personal risk The system is based upon Personal Security Transceivers PST a High Performance Desk and a Field Control Panel FCP The system incorporates security facilities such as manual alarm and automatic system scanning In addition a detector circuit is built into the transceiver which will initiate an alarm procedure when no movement of the transceiver is detected Communication between the PST and the FCP is always via the LBB 5800 Desk Each FCP monitors the status of its own PSTs programmed into the system An FCP can be programmed to monitor the PST s fully automatically without any action by the operator or PST holder and also by manual confirmation of the PST holder 12 size Each Field Control Panel can cater for up to 16 PSTs and the PSTs are programmed to react to their dedicated call buttons and LEDs on that particular panel Up to 31 FC Ps can be interconnected via the desk A High Performance Desk LBB 5800 can supply enough power to support only one FCP If more than one FCP is2. 4 ddecoccodcccocce ny a a 7 NO TONE CRICKETED TONE 8 o 9 oe o r A oo do oc do B ode ddo doo coe C ddecodcodcccccco D o 3 o o E oo eo NO TONE DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 14 15 TABLE 3 The codinf value transmitted by the PST during any kind of acknowledge alarm call is assigned a particular status in the FCP This TABLE lists the codinf digit and status of the each in the FCP CODINF DIGIT 0 and 2 land 3 FUNCTION The alarm LED status is updated to no move switch off W hen no acknowledge is expected then call desk function will be activated when FCP set for call panel 1 W hen acknowledge is expected the call will be accepted as the auto acknowledge reply The alarm LED status is updated to no move switch off The call desk function will be activated when the FCP is set for call panel 2 W hen acknowledge is expected the call dek will be accepted as the auto acknowledge reply The alarm LED status is updated to no move switch on W hen no acknowledge is expected then call desk function will be activated when FCP set for call panel 1 W hen acknowledge is expected the call will be accepted as the auto acknowledge reply The alarm LED status is updated to no move switch on The call desk function will be
3. preprogrammed alarm call can be automatically routed to another PST A built in delay timer can activate one to three relay outputs in the FCP which can be used to activate some other device e g telephone exchange The relay function can be programmed for continuously ON or pulsed ON 2 PROGRAMMING THE FCP 2 1 General All programming of the FCP must be carried out via the LBB 5800 desk The FCP must first be set present by the allocation of a dedicated address and all the various functions required by the customer must be done by further software programming O nly One uninitialised FC P may be connected to the RS 422 line at any given time W hen an uninitialised FC P is powered up the top row of LEDs will all blink slowly W hen initialised the FCP address LED will be illuminated during power up These are represented by the top two rows of LEDs 1 31 reading from top left to bottom right The power LED in the top left corner will be illuminated Powering up the desk with an FCP connected takes max 60 sec 2 2 Editor The Editor function of the desk is the means by which the system variables are programmed into the FCP W hen the Editor is opened the program variables can be entered via the keyboard and the desk bleeper gives an audible indication of correct or incorrect entries The normal sequence of programming the FCP is to first enter the required MENU followed by the menu COMMAND DIGIT followed by the PRO GRAM
4. PS menu mode Eronneous keystrokes will generate the error bleep and the desk will return to the PS menu mode 6 MENU MONITOR KEY Call FCP Desk combination W hen this menu is opened the display info will differ depending on how many FCPs are connected 1 More than one FCP connected Display shows sel FCP Nr and the lowest allocated address of which the status is present is displayed Scroll through the FC P addresses with the PRO GRAM key and input the desired address with the DIRECT CALL key 2 One FCP connected The display shows Call Desk X when the menu is opened where X current setting of the call desk function The FCP will not react to a call desk function The FCP will respond to call desk FC P combination 1 The FCP will respond to call desk FCP combination 2 The FCP will respond to call desk FCP combinations 1 and 2 gt lt gt lt gt lt gt lt tou ue 1 WNrFr Keystrokes 0 1 2 or 3 will change the display according to selection Press the PRO GRAM key to enter the new data and to close the menu Program returns automatically to the PS 6000 menu status 7 MENU A Auto Scan Call This menu is used to program a Enable inhibit channel for Auto Scan b Codinf input for manual reply call c System scan call repeat time d Acknowledge type e Manual acknowledge delay time f Auto Manual acknowledge call ratio Use the PRO GRAM key to enter the changed position value Th
5. VARIABLE S Philips Communication amp Security Systems PHILIPS DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 2 15 During programming the desk display will show the program information as it is entered Use the DIRECT CALL key of the desk to select the correct FCP number if more than one connected the PRO GRAM key to enter the selected data and scroll on to the next command If acall string is selected and the RESET key is pressed this will allow you to edit the last digit entered but if the RESET key is pressed again the desk will return to the Menu mode and the changed selected data will NOT be accepted 2 3 Opening The Editor NB All programming must be done via a connected LBB 5800 desk To open the editor a Press and hold PROGRAM key The display shows PROGRAM b Press keys A B C and D in sequence The diplay shows PROGRAM and A B C D as they are entered After the D is entered the display shows Menu C Release the PRO GRAM key The editor is open the display shows PS Menu and the Editor open tone will sound Remark Always enter the Edit mode from the Stand By mode of the LBB 5800 D esk 2 4 Closing The Editor The Editor can be closed by pressing the RESET key when the display shows MEN U If the RESET key is pressed whilst entering data then the last digit entered can be changed If RESET is pressed
6. activated when the FCP is set for call panel 2 W hen acknowledge is expected the call will be accepted as the auto acknowledge reply The alarm LED status is updated to no move alarm constantly lit The constantly lit function of the alarm LED has the highest priority W hen acknowledge is expected the call will be accepted as the auto acknowledge reply to activate the call panel 1 function the PST should be reset first These calls are ignored CALL PANEL FUNCTION The desk will send all received field calls with no 5 digit info to the FCP W hen the call is located in the acknowledge call address table of the FCP then the FCP will interpret this as a panel call if No auto acknowledge call waiting the page line is not at code level and the time between the last code line level and the field call gt 1 Channel status ignored INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 15 15 December 1997 LBB 5800 High Performance Control D esk Key to symbols 1 Handset LBB 5804 optional Can be use instead of the desk microphone and speaker 2 Display window LCD to display 16 digit information 3 Power On indicator LED Green 4 Transmission O n indicator LED Red 5 Desk in use indicator LED Yellow 6 Program key Used to program the desk and additional receivers into the system 7 D
7. used in the system they must be powered via an external supply unit The RS 422 communication bus can be used to connect all the FC Ps together in parallel to the LBB 5800 Desk see page 15 for system set up 13 Scanning The FCP can be programmed to scan the PST s in the system at preprogrammed intervals and check the status of each An automatic or an additional manual response from the PST to this check call can be programmed for each individual channel into the FCP In the former instance the PST will automatically send the status information back to the FCP without disturbing the PST INSTALLATION INSTRUCTIONS 69 December 1997 Page 1 of 15 LBB 6005 holder whereas in the latter the PST holder must within a predetermined time acknowledge that a call has been received by pressing the Alarm Reset Button on the PST W hen the auto scan facility is programmed and set for user enable inhibit the auto scan facility will be activated by pressing the channel Auto Scan key on the FCP pressing Auto Scan key again this will disable the auto scan activity and so on L4 Field Alarm Calls The FCP can be programmed to react to an Alarm Call from the PST in several ways W hen the Alarm LED lights a D irect Call can be transmitted to establish contact with the PST holder This call will be initiated by using the D irect Call Key for that channel If no action is taken by the operator within a predetermined time a
8. EM WIRING Installation details of the various units in the PS 6000 system can be found in the relevant Installation Instructions see contents DP 6000 PAGING LIN 16 pin Hirschmann Plug The number of power supply units PSU required is 1 ur 16 1 determined by the size of the system and the distance the various units are apart LBB 5934 00 12V 1A 1 16 Data audio output to the transmitter Data audio output to the transmitter 4 wire transmitter switching line System earth Audio DP 6000 code input talk back Audio DP 6000 code input talk back 4 wire squelch line 12V power supply Pins9and 10 sync lines Pins 15 and 16 monitoring Socket L 2 3 ah Gh 3 x external relay outputs from each FCP E na FCP type LBB 6005 00 Each FCP can cater for up to 16 transceivers A max of 31 FCPs can be used off one desk FCP consumes 180 mA therefore extra PSUs are required Control desk LBB 5800 00 Ext alarm contacts pins 9 16 Ce LBB 6010 6110 fitted with LBB 6015 LBB 6151 01 LBB 6151 00 DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 12 15 CENTRAL TRANSMITTER Power Supply Unit PSU LBB 5834 Quantity depends on system configuration If more than one FCP is used they must be powered separately and not via the DP 6000 or RS 422 system cabling Extended Systems Max 32 Field Contro
9. am execution as from power up Keystroke 0 NO restart execution COMMAND 2 SHOW STO P ADDRESS all FC Ps DISPLAY SHO WS SHW ADR 1 0 Keystroke 1 All FCPs will show their addresses by illuminating the appropriate LED Keystroke 0 Stops Show Address Mode and returns FCP to current status After either keystoke the desk will return to the Comm Service menu NOTE Stop Show Address mode must always be selected after Show Addres mode to restart communication DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 4 15 COMMMAND 3 ALLO CATE ADDRESS DISPLAY SHOW S GIVADR 1 0 Keystroke 1 W ill give the connected uninitialised FC P the lowest free unallocated address auto matically see also Command 4 After the keystroke the desk will return to the communication menu Eronneous keystokes will generate the error bleep and return to the Comm menu Keystroke 0 Return to Communication menu COMMAND 4 FCP STATUSCONTROL DISPLAY SHOW S STA FCP N R Enter the FCP address 01 31 which is to display its status only if more than one FCPs are connected The display of the Desk now shows the selected FCP address followed by the status The FCP is working normally Display shows xx Present The FCP address has not been allocated Display shows xx Unallocated The address has been allocated but the FCP is no
10. atus in enable The display will now show the selected status Press the PRO GRAM key to edit the next step RESET key to move to Update 5 2 EDITING THE DIRECT CALL STRING The display will show FCP Nr Channel Nr d and the call string e g 0105d The new call string can be entered using the desk hex key pad Address 4 digits Codinf 1 digit Info 5 digits This call will be transmitted when the FCP channel DIRECT CALL key is pressed Press PROGRAM key to go to next program step RESET key to move to Update DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 6 15 5 3 EDITING THE ALARM CALL STRING The display will show FCP Nr Channel N r a and the call string e g 0105a The alarm call data can be edited using the hex key pad Address 4 digits Codinf 1 digit Info 5 digits This call will be transmitted if a An internal relay is programmed b The alarm call is enabled for this relay c The relay delay time is over Press PRO GRAM key to go to next program step RESET key to move to U pdate 5 4 EDITING THE PST ACKNOW LEDGE ADDRESS The display will show FCP N r Channel N r and the acknowledge address 4 digits of the selected channel e g 0105 0000 The address will be the acknowledge address of the transceiver and to be programmed here Use the desk hex key pad to edit the addr
11. cted 1 More than one FCP connected Display shows Sel FCP Nr and the lowest allocated address of which the status is present is displayed Scroll the FCP addresses with the PRO GRAM key and enter the displayed address with the DIRECT CALL key The display shows Relay Nr now select relay number 1 3 and enter by the PRO GRAM key 2 One FCP connected The display shows Relay Nr now select relay number 1 3 and enter by the PRO GRAM key INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 9 15 December 1997 8 1 FUNCTION ASSIGN MENT The display will now show the current setting of the FCP e g Function position 123 4567 8 9 Display shows A tS tot ot xx y xx FCP Nr y Relay Nr Enter the required status by keying in position Nr 1 7 followed by keystrokes 0 or 1 Keystroke 0 inhibits the function and the display will indicate I in this position Keystroke 1 enables the function and the display will show function letter i e A and S above The PRO GRAM keystroke will store the new data and scroll to the next program step 8 2 DELAY ACTION TIME The display will show the current delay action time of the selected relay e g D EL xx 01 2 xx the current delay time FCP N r 01 relay Nr 2 Values between 00 and 99 seconds are valid entries Enter the new time and scroll to the next program step by pressing the PRO GRAM ke
12. d info digits c Edit the Alarm Call String d Edit the PST acknow ledge address e Enable inhibit speech after direct call e Manual automatic acknowledge mode f Alarm Call repeat time o Manual acknowledge time W hen editing the following Direct Call data pressing the PRO GRAM key will go to the next program step When the display shows update the PROGRAM key must be used to store data After PROGRAM key action the D esk continues with the next channel number Pressing RESET during sub menu programming the display shows update Pressing RESET whilst desk display shows PS menu the desk steps out of the Editor mode W hen the edit Direct Call menu is opened the display info will differ depending whether one or more FCPs are connected 1 More than one FCP connected Display shows sel FCP nr and the lowest allocated address of which the status is Present is displayed Scroll the FCP addresses with the PRO GRAM key and input the desired address with the DIRECT CALL KEY The display will now show sel Chan nr Select the channel to be edited 01 16 and the display will show the channel Nr followed by DC inhibit or DC enable 2 One FCP connected The sequence is as previous paragraph but starts from sel Chan nr displayed 5 1 ENABLE INHIBIT THE CALL STRING Keystroke 0 W ill set or leave the status in inhibit Keystroke 1 W ill set or leave the st
13. e RESET key will set the desk to the PS menu mode again Pressing the RESET whilst an FCP or channel is selected will return the desk to the PS MEN U status W hen this menu is opened the display info will differ depending on how many FC Ps are connected 1 More than one FCP connected Display shows sel FCP Nr and the lowest allocated address of which the status is present is displayed Scroll through the FC P addresses with the PRO GRAM key and input the desired address with the DIRECT CALL key 2 One FCP connected The display shows Sel Chan N r DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 8 15 The display will now show Sel Chan Nr select the channel to be edited 01 16 and the display will show the programmed auto scan status of the channel e g e c xx am yy 1 zz Location 123 4 5 6 7 Where e auto scan enabled or d for auto scan disabled c codinf value for an auto scan with manual acknowledge see table 2 bleep patterns XX auto scan repeat time in minutes 00 99 am auto scan acknowledge type key 4 1 A auto reply key 4 2 M manual reply key 4 3 AM auto manual This selection must be combined with location 6 Call Ratio which determines how many auto scans max 16 precede the required manual acknowledge e g if 5 is selected at location 6 then there will be 5 auto scans and the next will requi
14. e error bleep and the desk will return to the PS menu mode 5 7 ALARM CALL REPEAT TIME The display will show FCP Nr and Channel Nr followed by alm time time digits e g 0105 ALM TIME Enter the desired time 010 255 seconds a The Alarm Call will not be transmitted if the time set 000 b The time set to 001 Alarm Call will be transmitted only once c The Alarm Call will be repeated when the time set is between 010 and 255 Press PRO GRAM key to go to next program step RESET key to move to U pdate command Eronneous keystrokes will generate the error bleep and the desk will return to the PS menu mode Alarm call repeat stops by a manual reset from the PST or from the FCP NOTE Programmed Alarm Calls will only be active when enabled by relay programming see para 8 4 INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 7 15 December 1997 5 8 MANUAL ACKNOWLEDGE TIME The display will show FCP Nr and Channel Nr followed by ack time followed by the programmed time e g 0105 ACK TIME Enter the desired time from 000 254 seconds The time may not be set to 255 seconds Press the PRO GRAM key The display will show Update A further PRO GRAM keystroke will update the new programmed data and scroll to the next channel Direct Call Editor A RESET keystroke during update displayed will skip the new entered data and steps to the
15. ess of the PST Pressing the PROGRAM key will scroll on to the next program step to be edited If necessary the acknowledge address of the PST can be viewed by entering the Service Menu E followed by Command D will display CDIS enable or C DIS inhibit Keystroke 0 will set or leave the status in inhibit Keystroke 1 will set or leave the status in enable In the enable mode if a Field Calll is made from the PST the programmed address of the PST followed by the codinf will be displayed on the desk RESET to move to update NOTE Ensure that the status is set to C D IS inhibit before returning to normal Paging PS 6000 use 5 5 SPEECH The display will show the selected channel followed by speech enable or speech inhibit Keystroke 0 W ill set or leave the status in inhibit Keystroke 1 W ill set or leave the status in enable Press PRO GRAM key to go to next program step RESET key to move Update command 5 6 MANUAL AUTO ACKNOWLEDGE MODE The display will show FCP Nr Channel N r and one of the acknowledge modes like ack inh ack aut ack man or ack a m Keystroke 0 W ill set or leave the status in acknowledge inhibit Keystroke 1 W ill scroll the next status of the other three above modes Press PRO GRAM key to go to next program step RESET key to move to Update Eronneous keystrokes will generate th
16. irect call key Used to send one of 16 possible preprogrammed messages to selected receivers 8 Call transmit key Used to transmit a call 9 Monitoring key Used to enable or disable the talk back to the desk 10 Alarm call key Red Priority key used to call areceiver in an emergency situation 11 Reset key Blue Used to reset the call desk 12 Talk through key allows the operator to connect a speech call between two transceivers 13 Talk key Used to activate the speech mode of the desk 14 Microphone Located beneath the grille 15 Priority key If the system is occupied with a speech call the key gives the desk priority over this call 16 Keyboard Call selection keys 0 9 and A B C D E and
17. l Panel LBB 6005 RS 422 Cable Control Desk LBB 5800 Fig 2 LBB 6010 or VHF or UHF Central Talk back Receiver with Pilot tone Decoder LBB 6015 Personal Security Transceivers LBB 6065 xx LBB 6066 xx 16 per control panel Mains Master Storage Racks LBB 6151 01 Max 5 slaves LBB 6151 00 to each Master Rack INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 13 15 December 1997 TABLE 1 FCP DEFAULT VALUES FUNCTION DEFAULT VALUE FCP Address not inialised h 50 Relay 1 2 3 function assignment ee Fes an Ka E Relay 1 2 3 delay time 30 seconds Relay 1 2 3 pulse time 00 pulse inhibit Relay 1 2 3 standby status energised Relay 1 2 3 alarm call transmission inhibit Call Desk FCP Nr Call Desk FCP Nr 1 and2 Direct call all channels inhibit Direct call string 0000000000 arm call string 0000000000 cknowledge address 0000 A A Speech status enable Acknowledge mode Auto acknowledge arm call inhibit repeat mode inhibit ime window for manual acknowledge 30 seconds uto scan inhibit uto scan repeat time all channels 5 minutes knowledge mode all channels Auto acknowledge Auto acknowledge and manual acknowledge ratio 1 ee BLEEP PATTERN Table 2 o a Transceiver bleep patterns associated 1 je ah a with the codinf value 2 dd oc co co 3 ede ccc cco coe
18. m Variables As long as the PS menu is open the text PS menu will be displayed and a bleep will sound every second W hen a PS 6000 sub menu is selected the bleep will stop and the desk display will show the text associated with the sub menu selected W hen asub menu has more than one step the next step to be programmed can be selected by pressing the PRO GRAM key At the end of some sub menus the display will show update To enter the programmed data into the memory press the PRO GRAM key again By pressing the RESET key instead of the PRO GRAM key the new entered data is lost The desk will revert to PS menu selection The following text describes the menus and commands to be programmed into the FCP 4 MENU KEY C Communication initialisation COMMAND 0 FCP DEFAULT SETTING see TABLE 1 DISPLAY SHOW S DEF FCP NR Key in the address of the FCP if more than one FCPs are connected to be set to default values 01 31 Only connected FC Ps may be selected The memory of the FCP will be initialised The FCP will restart its program by a soft reset The address allocated in the desk will be deleted The top row of LEDs of the FCP will start to blink If when powered up the top row of LEDs are blinking the FCP is in the default mode see TABLE 1 Remark only one FCP initialised COMMAND T FO RCE SOFT RESET DISPLAY SHO W S SFTRES 1 0 Keystroke 1 W ill reset ALL FC Ps and restart the progr
19. re a manual response from the Transceiver holder yy manual acknowledge time in seconds 00 99 1 auto to manual acknowledge call ratio 0 F zz the selected channel number not programmable Keystrokes 1 7 will select the location on the display to be edited e g if the auto scan repeat time only has to be edited then press key 3 and enter the new time to disable auto scan press 1 followed by 0 Pressing 1 followed by 1 enables auto scan Use the PROGRAM key to enter the completed input Eronneous keystrokes generate the error bleeps 8 MENU ALARM KEY Edit Functional Relay Status This menu is used to program the relays to be active by system functions independantly of each other a Relay function assignment AM N S F D C default LLLLILILI b Relay action delay time 00 99 seconds c Relay pulse time 00 99sec 00 infinate d Relay stand by status energised de energised e Alarm call transmission enabled inhibited Position Indication Function Display indication for function 1 A No manual alarm 2 M Manual alarm 3 N No move alarm 4 S No move switch off 5 F Field call received 6 D Direct call activated 7 C Auto scan auto acknowledge not received If the relay is inhibited for a function the display will show I instead of the function character W hen this menu is opened the display info will differ depending on how many FC Ps are conne
20. s from U nalloc to Present will allocate the address to the FCP and the FCP LEDs will stop blinking immediately and the FCP can communicate with the desk If when scrolling the addresses the chosen address happens to show Allocated or Reply MB then it is not possible to go directly to Present to install the address in the FCP In this case change from Allocated or Reply MB to Unallocated then go to Present and the FCP will accept the address within a scan time of 1 Min approx The FCP has now accepted the address and communication with the desk is established INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 5 15 December 1997 43 Address Status Changing within Command 4 STA FCP NR Submenu The following gives the correct key selections necessary to move from one status to another FROM TO KEY IN FROM TO KEY IN Present Allocate 0 1 Unalloc Present 1 1 Present Unalloc 0 2 Unalloc Allocate 1 1 0 1 Present Reply MB 1 3 Unalloc Reply MB 1 1 1 3 Allocate Present 1 1 Reply MB Present 0 3 1 1 Allocate Unalloc 0 2 Reply MB Allocate 0 3 0 1 Allocate Reply MB 1 3 Reply MB Unalloc 0 2 5 MENU DIRECT CALL KEY Edit Direct Call This menu is used to program a Enable inhibit the call string b Edit the direct call address codinf an
21. t connected Display shows xx Allocated This mode is for future applications Display shows xx Reply Maybe Keystroke 0 Used to reset a parameter Display shows Parameter Keystroke 1 Used to set a parameter Display shows Parameter The parameters can be selected using the following 3 keys Keystroke 1 Present Keystroke 2 Allocation Keystroke 3 Reply MB 4 1 Address Allocation It is possible that an address 01 31 could be set reserved by either of the three parameters mentioned above before a new FCP is introduced to the desk To check the status of each of the 3lcommunication addresses scroll the addresses using the PRO GRAM key The status of each will be shown on the desk display If an address number has already been allocated to an existing active FCP the display should show Present when that address is selected Only Unalloc addresses can be directly assigned to an uninitialised FCP 4 2 Addressing an FCP An uninitialised FC P can be given an address in two ways 1 As at Command 3 where the FCP will be given the first Unalloc address available automatically and the LEDs will stop blinking immediately 2 If a particular address number has to be assigned to an FCP this can be done by scrolling the available addresses with the PROGRAM key until the selected address is shown in the desk display By changing the status of this addres
22. wer supply from the desk fused at 1 AT not connected not connected RS 422 serial int B extra 220 O hm OV 12 V power supply from the desk fused 1 AT not connected RS 422 serial int A extra 220 O hm OV screening not connected X2 9 pin D type socket for external alarm functions Pin No 1 make 2 break 3 middle 4 make 5 break 6 middle 7 make 8 break 9 middle Function relay contact RE1 relay contact RE1 relay contact RE2 relay contact RE3 relay contact RE3 relay contact RE1 relay contact RE2 relay contact RE2 relay contact RE3 screening not connected Relays can only be used on voltages not exceeding 34 VDC and a current of 1 A maximum 2 5 m long interconnecting cable between desk and FCP wiring details 9 pin D type on FCP 25 pin D type of D esk Pin N o 9 pin W ire Pin Nr 25 pin 1 12V blue 23 12V 6 12V red 25 12V 5 0V black 17 0V 9 0V grey 24 0V 4 RS422 B green 14 RS422 B 8 RS422 A yellow 16 RS422 A 2 others not 3 not connected connected 7 Cable length between the LBB 5800 Desk and the LBB 6005 FCP may be extended to a distance of approx 1000 metres FCP Rear view Bear in mind that if the Desk is separated from the FCP that speech communication with the PST is via the microphone speaker in the Desk INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 11 15 December 1997 PS 6000 and DP 6000 SYST
23. whilst a Menu is open the desk will revert to the menu selection mode If pressed a second time then the Editor mode will close 2 5 Bleep Tones The following bleep tones can be heard during programming 0 2 seconds gt e a Key confirmation ea cere ea terns chilean b Editior open c Menu open d Command open e Input accepted f Error 5 pulses 2 6 Setting The Desk W ork Mode The desk work mode must be set before programming can be carried out O pen the Editor see para 2 3 press MEN U key E followed by Command key 7 then selecting key 3 for the PS 6000 mode the desk layout is shown at Fig 3 o selects the LBB 5800 mode y selects the LBB 5801 mode 2 selects the LBB 5802 mode 3 selects the PS 6000 mode INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 3 15 December 1997 3 FCP PROGRAMMING 3 1 PS 6000 menu selection To enter the PS 6000 menu OPEN THE DESK EDITO R SELECT and PRESS key A as shown in para 2 3 and observe the correct display indication DISPLAY PS menu W hen the PS 6000 menu is opened the following sub menus can be selected to program the FCP KEYSTROKE SUB MENU C Communications Initialisation DIRECT CALL KEY Direct Call info MONITOR KEY Call FCP setting A Auto scan info ALARM KEY Relay settings E FCP memory edit USED ONLY FOR SERVIC E 3 2 Entering T he Progra
24. y 8 3 PULSE TIME The display will show the current pulse time of the selected relay e g PT xx 01 2 xx the current pulse time FCP N r 01 relay Nr 2 Values between 00 and 99 seconds are valid entries Pulse time 00 W ill inhibit the pulse action and set the relay after delay time to active Enter the new time and scroll to the next program step by pressing the PRO GRAM key 84 STANDBY STATUS The display will show the current relay standby status e g de ener 01 2 or energ 01 2 FCP Nr 01 relay Nr 2 Keystroke 0 W ill set or leave the status to de energised Keystroke 1 W ill set or leave the status to energised Scroll to the next program step by pressing the PRO GRAM key 85 ALARM CALL TRANSMISSION The display will show ALC enable or ALC inhibit Keystroke 0 W ill set or leave the status to alarm call transmission inhibit Keystroke 1 W ill set or leave the status to alarm call transmission enable Enter the new status and press the PRO GRAM key Pressing the PRO GRAM again will scroll to the next relay Nr Press the RESET key to return to PS menu mode and RESET key again to close the Editor mode DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 10 15 9 WIRING DETAILS X1 9 pin D type socket for connection to the High Performance desk LBB 5800 Pin No 1 ou WN 7 8 9 Function 12 V po
Download Pdf Manuals
Related Search