Home

Perle Systems S-1110DP User's Manual

1. Compliance Information FCC This product has been found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions in this Guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense EN 55022 Class A WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures EN 55024 Class A Laser Safety IEC 60825 1 2007 This product meets Class Laser safety requirements per IEC 60825 1 2007 standard and complies with FDA CDRH 21 CFR1040 10 and 21CFR1040 11 WARNING Visible and invisible laser radiation may be present when cables are not connected Do not stare into the beam or view the beam directly with optical instruments Failure to observe this warning could result in an eye injury or blindness WARNING Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation
2. Perle PoE PoE 10 100 1000 Ethernet Media Converters Installation Guide S 1110P S 1110PP S 1110DP S 1110DPP P N 5500317 11 Overview This document contains instructions necessary for the installation and operation of the Perle Standalone PoE PoE 10 100 1000 rate converting Media Converters S 1110P These products have the ability to convert 10 100 1000Base T cable connections copper to 100 1000Base X connections fiber The Perle media converters function as a PoE switch and support a variety of port configurations including single or dual UTP and fiber ports These media converters function as Power Sourcing Equipment PSE and can power either one or two Powered Devices PDs using standard UTP cables that carry Ethernet data The S 1110P models are compatible with Powered Devices that comply with the IEEE 802 3af standard and the S 1110PP models are compatible with Powered Devices that comply with both the IEEE 802 3af and the 802at 2009 standard The fiber connection can be either single mode SM or multimode MM and can operate over different wavelengths and distances depending on the model selected see table below 2 Port Models PoE P Connector Mode Wavelength PoE PP xx Distance TX RX S 1110PP M2x 05 Die 550 m 1804 ft Bao am SIOR eii SeSi TO an 2 Ho s iiiopp sisciou SC TO km 62 mi 1510 1490 mm siiiopp siscion SC 10 km 62 mi 1490 1310
3. 1310 Min 9 5 Min 20 10 5 S 1110PP S2xx10 RX 1310 Max 3 Max 3 24 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide PoE P Wavelength TX Power RX Power PoE PP Mode nm dB dB Budget S 1110P S1SC10U SM TX 1310 Min 9 Min 20 11 S 1110PP S1SC10U RX 1490 Max 3 Max 3 S 1110P S1SC10D SM TX 1490 Min 9 Min 20 11 S 1110PP S1SC10D RX 1310 Max 3 Max 3 S 1110P S1SC20U SM TX 1310 Min 8 Min 22 14 S 1110PP S1SC20U RX 1490 Max 3 Max 3 S 1110P S1SC20D SM TX 1490 Min 8 Min 22 14 S 1110PP S1SC20D RX 1390 Max 3 Max 3 S 1110P S2xx40 SM TX 1310 Min 3 Min 23 20 S 1110PP S2xx40 RX 1310 Max 5 Max 3 S 1110P S1SC40U SM TX 1310 Min 3 Min 23 14 S 1110PP S1SC40U RX 1490 Max 2 Max 3 S 1110P S1SC40D y TX 1490 Min 2 ee i S 1110PP S1SC40D RX 1310 Max 3 eee Max 3 S 1110P S2xx70 SM TX 1550 Min 2 Min 23 21 S 1110PP S2xx70 RX 1550 Max 5 Max 3 S 1110P S1SC80U SM TX 1510 Min 2 Min 26 24 S 1110PP S1SC80U RX 1590 Max 3 Max 3 S 1110P 1SC80D SM TX 1590 Min 2 Min 26 24 S 1110PP 1SC80D RX 1510 Max 3 Max 3 S 1110P S2xx120 SM TX 1550 Min 0 Min 32 32 S 1110PP S2xx120 RX 1550 Max 5 Max 3 S 1110P S1SC120U SM TX 1590 Min 3 Min 34 31 S 1110PP S1SC120U RX 1510 Max 2 Max 9 S 1110P S1SC120D SM TX 1510 Min 3 Min 34 31 S 1110PP S1SC120D RX 1590 Max 2 Max
4. 9 S 1110P S2xx160 SM TX 1550 Min 2 Min 34 31 S 1110PP S2xx160 RX 1550 Max 5 Max 9 S 1110P SFP S 1110PP SFP SFP Note 1 Note 1 Note 1 Note Note 1 Fiber characteristics will depend on the SFP fiber module selected Perle PoE PoE 10 100 1000 Ethernet Media Converter 25 Installation Guide 3 Port Models Dual Copper PoE DP Mode Wavelength TX Power RX Power Budget Dual Copper PoE nm dB dB dB DPP S 1110DP M2xx05 MM TX 850 Min 9 5 Min 17 75 S 1110DPP M2xx05 RX 850 Max 4 Max 3 S 1110DP S2xx10 SM TX 1310 Min 9 5 Min 20 10 5 S 1110DPP S2xx10 RX 1310 Max 3 Max 3 i S 1110DP S1SC10U SM TX 1310 Min 9 Min 20 11 S 1110DPP S1SC10U RX 1490 Max 3 Max 3 S 1110DP S1SC10D SM TX 1490 Min 9 Min 20 11 S 1110DPP S1SC10D RX 1310 Max 3 Max 3 S 1110DP S1SC20U SM TX 1310 Min 8 Min 22 14 S 1110DPP S1SC20U RX 1490 Max 3 Max 3 S 1110DP S1SC20D SM TX 1490 Min 8 Min 22 14 S 1110DPP S1SC20D RX 1310 Max 3 Max 3 S 1110DP S2SC40 SM TX 1310 Min 3 Min 23 20 S 1110DPP S2SC40 RX 1310 Max 5 Max 3 S 1110DP S2ST40 SM TX 1310 Min 3 Min 23 20 S 1110DPP S2ST40 RX 1310 Max 5 Max 3 S 1110DP S2LC40 SM TX 1310 Min 3 Min 23 20 S 1110DPP S2LC40 RX 1310 Max 2 Max 3 S 1110DP S1SC40U SM TX 1310 Min 3 Min 23 14 S 1110DPP S1SC40U RX 1490 Max 2 Max 3 S 1110DP S1SC40D SM TX 1490 Min 2 Min 23 14 S 1110D
5. 1 A Loses fiber connection on its receiver 2 A Sends FFA 3 B Detects FFA signal and shuts down the fiber link 4 B Drops link on copper connection because Smart Link Pass Through is configured 5 A Link on copper connection is not affected because Smart Link Mode is set to Standard Duplex copper Switch 4 Switch Position Copper port 1 Copper port 2 Up default Full Duplex NA Down Half Duplex NA Note When Auto Negotiation SW1 is set to Off the media converter will use this Duplex setting for copper port 1 Full Duplex In the Up switch position the media converter will be set to Full Duplex mode Half Duplex The media converter will be set to Half Duplex mode Perle PoE PoE 10 100 1000 Ethernet Media Converter 11 Installation Guide Speed copper Switch 5 Switch Position Copper port 1 Copper port 2 Up default 100 NA Down 10 NA Note When Auto Negotiation SW1 is set to Off the media converter will use this switch setting for copper port 1 speed 100 When Switch 5 is in the Up position the S 1110P will force the speed to 100 Mbps 10 When Switch 5 is in the Down position the media converter will force the speed to 10 Mbps Auto Fiber Negotiation Switch 6 Switch Fiber 1 Fiber 2 Position 1000 Mbps 1000 Mbps Up default Auto Auto Down Off Auto Auto The Media Converter will negotiate Ethe
6. Enabled Enabled Down Disabled Enabled Enabled If the media converter detects a loss of signal on the fiber receiver it will immediately disable its fiber transmitter signal on the same port This in effect notifies the fiber link partner that an error condition exists on the fiber connection If the remote media converter is set up for Fiber Fault Alert FFA and the local media converter is set up with Link Pass Through a loss of fiber link on either the transmit or receive line will be passed through to the local copper connection thus notifying the connected device If the media converter has been set to Smart Link Pass Through mode the effect will be the same as FFA since the link loss on the fiber receiver will result in bringing down the copper link which will in turn cause the transmit fiber link to be brought down Note This feature only takes effect if Fiber Negotiation has been turned off Disabled The media converter will not monitor for or generate Fiber Fault Alert 10 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Illustration of the FFA The following diagram is an illustration of the operation of this feature A Remote Media Converter setup for Fiber Fault Alert Enabled Fiber Negotiation OFF and Link Mode Standard B Local Media Converter setup for Fiber Fault Alert Enabled Smart Link Pass Through On and Fiber Negotiation OFF
7. lost at which time a switch over to fiber port 1 will occur Enabled Fiber port 1 will be designated as the Primary fiber port If a loss of link occurs on fiber port 1 which causes a switch over to fiber port 2 the S 1110P will monitor fiber port 1 for link restoration Once the link is re established and remains so for 6 seconds fiber port 1 will be re activated and fiber port 2 will be put back into stand by mode Perle PoE PoE 10 100 1000 Ethernet Media Converter 15 Installation Guide Installing the SFP Fiber Module SFP models only 1 2 3 4 Locate the appropriate fiber module and insert the SFP into the opening on the front of the media converter Ensure the SFP module is properly seated The release latch of the SPF fiber transceiver must be in the closed up position before insertion The SFP module may be inserted before or after applying power to the media converter Proceed with cable connections Installing the Duplex Fiber Cable 1 2 Locate a 1000Base X compliant duplex 2 strands fiber cable with appropriate connectors Connect the fiber cables from one media converter to the other media converter switch fiber device ensuring that the RX and TX are reversed crossed at the opposite end RX RX TX i TX Perle Media Perle Media Converter Converter Installing the Simplex Fiber Cable 1 16 Locate a 1000Base X compliant simplex 1 strand fiber cable with appropriate c
8. switches in the Up position 2 Connect the copper device to the copper port on the media converter The LKC LED light indicates good copper connection If the LKC LED is not lit the check the copper cable and the attached device 3 Repeat for the far end media converter 4 Connect the fiber cable to both media converters The LKF LED indicates good fiber connection If no LKF LED then check the fiber cabling Ensure the transmitter and receiver pairs are crossed 5 Return the units to the desired configuration Plug the other end of the power cord into an appropriate power outlet Method 2 The fiber connection can also be verified by configuring the remote media converter for loopback mode The LKF LEDs on both media converters should be lit Data should pass through the local converter over the fiber connection to the remote media 22 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide converter At the remote media converter the data will be looped back and passed through the fiber back to the local converter and passed to the copper link No Power to the PD 1 Ensure that the PD is compatible with the S 1110P If the PD is a POE device a POE media converter must be used S 1110PP 2 Ensure that the power supply being used is the one provided with the product 3 If the PD does not support Alternative A including legacy PD s the Power Option Jumpers must be set accordingly Also ensu
9. PP S1SC40D RX 1310 Max 3 Max 3 S 1110DP S2SC70 SM TX 1550 Min 2 Min 23 21 S 1110DPP S2SC70 RX 1550 Max 5 Max 3 S 1110DP S2ST70 SM TX 1550 Min 0 Min 23 23 S 1110DPP S2ST70 RX 1550 Max 5 Max 3 S 1110DP S1SC80U SM TX 1510 Min 2 Min 26 94 S 1110DPP S1SC80U RX 1590 Max 3 Max 3 S 1110DP S1SC80D SM TX 1590 Min 2 Min 26 94 S 1110DPP S1SC80D RX 1510 Max 3 Max 3 26 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Dual Copper PoE DP Mode Wavelength TX Power RX Power Budget Dual Copper PoE nm dB dB dB DPP S 1110DP S2xx120 SM TX 1550 Min 0 Min 32 32 S 1110DPP S2xx120 RX 1550 Max 5 Max 9 S 1110DP S1SC120U SM TX 1590 Min 3 Min 34 31 S 1110DPP S1SC120U RX 1510 Max 2 Max 9 S 1110DP S1SC120D SM TX 1510 Min 3 Min 34 31 S 1110DPP S1SC120D RX 1590 Max 2 Max 9 S 1110DP S2xx160 SM TX 1550 Min 2 Min 34 32 S 1110DPP S2xx160 RX 1550 Max 5 Max 9 S 1110DP SFP S 1110DPP SFP SKE Notet 21 Fiber Cabling Requirements MM 50 125 microns or 62 5 125 microns SM 9 125 microns Ethernet Copper Cabling Requirements e Category 5 UTP or STP e 24 22 AWG e Straight through or Ethernet crossover Note Please refer the product page on the Perle website for the most up to date models and specifications http www perle com Perle PoE PoE 10 100 1000 Ethernet Media Converter 27 Installation Guide
10. e connected to copper port 1 After 2 seconds the media converter will restore power to the PD and the power will remain on until one of the fiber links transitions from the link up to link down state Disabled When disabled the media converter will not perform PSE functions 14 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Fiber Redundancy Switch 7 Dual fiber models only Switch Position Mode Up default Disabled Down Enabled Disabled When this feature is disabled both fiber ports will operate as independent ports on a switch Normal switch rules and functions will apply Enabled When this feature is enabled fiber port 1 will be the primary active fiber connection port and fiber port 2 will be in standby and in an inactive state Should a loss of link occur on fiber port 1 fiber port 2 will be activated within 50 ms The MAC caching table for fiber port 2 will be cleared and the switch will begin to re learn Mac address routing See Redundant Primary for information on link connections Redundant Primary Switch 8 Note This switch is used in conjunction with the Fiber Redundancy feature to determine the behaviour after link restoration Switch Position Mode Up default Disabled Down Enabled Disabled Following the loss of link on fiber port 1 and the activation of fiber port 2 fiber port 2 will remain the primary port until its link is
11. e wad 1 Feed the power cord through the opening in the power cord relief clip 2 Attach the power cord relief clip to the chassis and secure with the provided screw 3 Plug the power cord into the AC power connector at the rear of the chassis 4 Plug the other end of the power cord into an appropriate power outlet Powering up the Perle Media Converter 1 Connect the Perle supplied power adapter to the media converter 2 Connect the power adapter to a power source 3 Check that the PWR LED light is lit 18 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Operation Status LED The Perle PoE PoE 10 100 1000 Rate converting Media converters have status LEDs located on the front panel of the unit 1000Base X 10 100 1000Base T On Power is applied to the unit Blinking slow Loopback mode one or both fiber interfaces are in loopback mode Blinking fast Power On failure See LED Pattern to determine pattern combination and failure cause LED Pattern FDF LKF FDC Off Off On SFP incompatible Internal hardware failure All other LED patterns FDF 1 2 Fiber 1 2 Duplex On Full Duplex Off Half Duplex LKF 1 2 Status on Fiber Link 1 2 On Fiber link is present Off No fiber link present Blinking slow Fiber link appears functional Fiber link has been brought down by Smart Link Pass Through Blinking fast Fibe
12. e will override all other switch settings Note On media converters with two fiber ports both ports can be in loopback mode at the same time Bank 2 PSE Enable Copper 1 Switch 1 2 PSE Enable Copper 2 Switch 4 5 dual copper models only Switch Position 1 4 Switch Position 2 5 Type PSE enabled Up default Up default normal detection PSE enabled High capacitance detection Up Down PSE enabled Down Up Legacy device detection Perle PoE PoE 10 100 1000 Ethernet Media Converter 13 Installation Guide Down Down PSE disabled These switches must be set in order to enable the power sourcing function and to indicate the type of device detection required If the device type is unknown the default should be used as per IEEE802 3af at standards Enabled When enabled the media converter will perform Power Sourcing Equipment PSE functions as per IEEE802 3af POE or 802 3at 2009 POE standards Disabled When disabled the media converter will not perform PSE functions PD Power Reset 1 Switch 3 PD Power Reset 2 Switch 6 dual copper models only Switch Position Mode Up default Disabled Down Enabled Disabled When disabled the loss of fiber link has no effect on PSE power to the PD device Enabled When enabled if the media converter detects loss of link on any fiber port it will turn off PSE output power to the PD devic
13. exposure 28 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Warranty Registration Perle s standard Lifetime Warranty provides customers with return to factory repairs for Perle products that fail under the conditions of the warranty coverage Details can be found at http www perle com support_services warranty shtml Contacting Technical Support Contact information for the Perle Technical Assistance Center PTAC can be found at the link below A Technical Support Query may be made via this web page www perle com support_services support_request shtml Copyright 2011 Perle Systems Limited All rights reserved No part of this document may be reproduced or used in any form without written permission from Perle Systems Perle PoE PoE 10 100 1000 Ethernet Media Converter 29 Installation Guide
14. gotiate the Ethernet parameters with the copper link partner The parameters used by the media converter will be determined by the Duplex switch 4 and Speed switch 5 DIP switch settings Note This switch affects the behaviour of copper port 1 only copper port 2 is always set to Auto Link Mode Switch 2 Switch Position Mode Up default Standard Mode Down Smart Link Pass Through Standard Mode In this mode link on the fiber and copper sides can be brought up and down independently of each other A loss Perle PoE PoE 10 100 1000 Ethernet Media Converter 9 Installation Guide of link on either the fiber or copper port can occur without affecting the other connection Smart Link Pass Through In this mode the link state on one connection is directly reflected through the media converter to the other connection If link is lost on one of the connections then the other link will be brought down by the media converter If the media converter has 2 copper or 2 fiber connections then both must go down in order to affect the other connection s If the installation has a media converter on both ends of the fiber link and both are set up for Smart Link Pass Through then a loss of copper link on the far end device will propagate through both media converters and will result in a loss of link at the near end device Fiber Fault Alert Switch 3 Switch Position Fiber Port 1 Fiber Port 2 Up default
15. jumper setting optional Set the DIP switch settings if required Set the Powering Option Jumpers if required Install and connect the fiber cable s Install and connect the copper cable s Power up the media converter NOOR WD Auto MDIX Jumper Settings Note The factory settings for Auto MDIX will work for most installations but in the rare case that you need to modify the settings the procedure is below For dual copper media converters each copper interface has an Auto MDIX jumper bank To access the Auto MDIX jumper settings unscrew the six side screws on the case and remove the cover plate Locate the MDIX AUTO jumper set as detailed below By covering or strapping pins 1 and 2 the S 1110P will operate as an MDIX device By covering or strapping pins 2 and 3 the S 1110P will automatically detect the Ethernet cable s polarity Removing the strapping is the same as AUTO Pinl Pin2 Pin3 MDI AUTO Note The default jumper setting is AUTO Perle PoE PoE 10 100 1000 Ethernet Media Converter 5 Installation Guide Power Sourcing Pinouts Note The factory settings for Power Sourcing Pinouts will work for most installations as 802 3a and 802at 2009 POE POE devices will detect and sync to the correct POE option However in the rare case that you need to modify the settings the procedure is below When Power Sourcing is enabled on a copper port the S 1110P will provide power to the connected PD device o
16. llation Guide 3 Dual Copper PoE DP Connector Mode Wavelength Dual Copper PoE DPP xx Distance TX RX S 1110DP S1SC80D SM S 1110DPP S1SC80D SC 80 km 50 mi BEST ue S 1110DP S2xx120 SM S 1110DPP S2xx120 SC ST 120 km 74 6 mi 1550 nm S 1110DDP S1SC120U SM S 1110DDPP S1SC120U SC Domo mee oe S 1110DP S1SC120D SM S 1110DPP S1SC120D SC 120 km 74 6 mi 1590 1510 nm S 1110DP S2xx160 SM S 1110DPP S2xx160 SC ST 160 km 100 mi 1550 0m S 1110DP SFP S 1110DPP SFP Sar Noii 3 Port Models SPF Model PoE P Dual SFP renin ae z ane PoE PP Dual SFP S 1110P DSFP SFP Note 1 Note 1 S 1110PP DSFP SFP Note 1 Note 1 4 Port Models SFP Model ae copper PoE Dual Connector Mode Wavelength Dual copper PoE Dual tey Distance ES SFP S 1110DP DSFP SFP Note 1 Note 1 S 1110DPP DSFP SFP Note 1 Note 1 Note 1 Fiber characteristics will depend on the SFP fiber module selected Please visit Perle s website for the most up to date Installation guides models and specifications http www perle com 4 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Installation The default DIP switch settings all switches in the UP position will work for most installations These are the steps required to configure the Perle S 1110P Ethernet media converter 1 Insert SFP Module SFP Model only Set the Auto MDIX
17. nk Mode 3 Fiber Fault Alert 4 Duplex copper 5 Speed copper 6 Fiber Negotiation 6 Full Half Duplex Fiber 100 SFP model only ay 7 Loopback 1 lt 8 Loopback 2 12345678 Bank 2 3 PD Reset 1 1 2 PSE Enabled 1 4 5 PSE Enabled 2 6 PD Reset 2 oo TEEN ds 12345678 Note All switch changes take effect immediately Switch changes will cycle power to the PD only if the PD Reset switch is set to On or you make changes to the PSE Power switches 8 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide DIP Switch Settings Bank 1 Auto Negotiation copper Switch 1 Switch Position Copper 1 Copper 2 Up default Auto Auto Down Off Auto Note Auto negotiation should only be turned off if the copper link partner does not support Auto Negotiation and fixed settings are required by the copper link partner Auto When enabled the media converter will negotiate with its link partner to determine the most optimal parameters for this connection The S 1110P will advertise capabilities of 10 100 and 1000 Mbps full and half duplex as well as pause and remote fault capabilities to the link partner If the copper link partner does not support Auto negotiation the S 1110P will parallel detect to 10 or 100 Mbps and force Half Duplex mode as per IEEE specifications Off When the Auto Negotiation switch is set to the OFF position the media converter will not ne
18. nm s i1iopp siscxou SC 20 kin 124 mi eee S 1110pp sisc20p SC kim 1490 1310 nm 1110PP 52xx40 SCSI nihii ae Siar a 5 een US mm Siler cise ons IS De pee aO in SO eo EER o naa Lesom 2 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide PoE P Connector Mode Wavelength PoE PP xx Distance TX RX S itopP siscsou SC 30 k50 mi yas S 1110PP S1SC80D SC 30 k50 mi ES Wine SIILOPP S2ax120 SYST TOTAS mi 1530 nm S 1110PP S1SC1200_ SC 120 E RSS S10PP Sisci200 SC 120 74 6 mi 1320 1310 mi S1110PP S2xx160 SYST 160 km 100 mi 10m S 11 10PP SFP SEP Note 1 Note 1 Fiber characteristics will depend on the SFP fiber module selected 3 Port Models Dual Copper POE DP Connector Mode Wavelength Dual Copper POE DPP xx Distance TX RX S 11 10DPP M2xx05 SEOST 550 nvisoan 8500m S 11 1ODPP S2xx10 SOSI TOkm62 mi 1310mm 1110DPP S1SC100 sc TOknv6 2mi 1310 1490 nm Siiopppsiscion SC TO km mi 14901310 nm 5 11 10DPP S1SC20U SC 20km 124mi 1310 1490 nm S1ioppPsisc2o SC 20km 124 mi 1490 1310 nm S 111ODPP 82xx40 SOSI 20 km25 mi 13100m 5 11 10DPP SISC40U SE JO kms mi 1310 1490 nm 5 11 10DPP S15C40D SC 10 km 25 mi 1490 1310 nm S ILIODPP 82xx70 SSB 70km 43 5 mi 13509 1110DPP 18C80U SC 30 knvs0 mi 1510 1590 nm Perle PoE PoE 10 100 1000 Ethernet Media Converter Insta
19. onnectors Ensure that the TX wavelength matches the RX wavelength at the other end and the RX wavelength matches the TX wavelength at the other end Connect the fiber cable from one media converter to the other media converter switch fiber device Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Installing the Copper Cable 1 Locate 10 100 1000Base T compliant copper cables with the appropriate connectors 2 Connect the RJ 45 cable between the Perle media converter and the device Note The Perle media converter supports Auto MDIX which allows connection of a straight through or cross over Ethernet cable See Auto MDIX Jumper Settings in this guide for jumper positions Grounding the Media Converter If your installation requires additional grounding the following procedure can be followed Grounding the chassis requires the following items e One grounding lug not provided e One 18 12 AWG wire not provided e Cross head screwdriver not provided Note For your safety when installing this equipment always ensure that the chassis ground connection is installed first and disconnected last Attaching the Grounding Lug 1 Attach the grounding lug to one end of an 18 12 AWG wire Perle PoE PoE 10 100 1000 Ethernet Media Converter 17 Installation Guide 2 Attach the grounding lug to the chassis and secure with the grounding screw s Attaching the Power cord strain relief clip ag
20. r link up and receiving data Perle PoE PoE 10 100 1000 Ethernet Media Converter 19 Installation Guide SPD Copper Port 1 2 Green 1000 Mbps Orange 100 Mbps Off 10 Mbps if link is currently established FDC 1 2 Duplex on Copper 1 2 On Full Duplex Mode Off Half Duplex Mode LKC 1 2 Link Status on Copper port 1 2 On Copper link is present Off No copper link present Blinking slow Copper link appears functional Copper link has been brought down by Smart Link Pass Through Blinking fast Copper link up and receiving data PSE 1 2 Solid Green Active The PSE has successfully detected a compliant PD and is applying power over the UTP Solid Orange Inactive The PSE is not active The PSE has been configured to provide power however e a compliant PD is not detected no power applied e a PSE has turned off power for Reset function Off Disabled The PSE function is disabled in the configuration Error conditions A blinking red light is an error condition The led light will cycle with a 3 second stop interval between the error condition code PSE 1 2 LED 1 blink PD Capacitance too high 2 blinks PD Resistance too low or short circuit 3 blinks PD Resistance too high 20 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Other Features Auto MDIX Auto MDIX automatic medium dependent interface crossover de
21. re the correct pin out for the device 4 For proper detection of different classes of devices the dip switches must be set correctly Perle PoE PoE 10 100 1000 Ethernet Media Converter 23 Installation Guide Technical Specifications The following applies to all S 1110P media converters Power Input Consumption 46V DC to 57V DC 6 W Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Altitude OC to 50 32F to 122F 25 to 70 13F to 158F 5 to 90 non condensing 5 to 95 non condensing Up to 3 048 m 10 000 ft Dimensions 150 mm by 95 mm by 26 mm MTBF No Power 1 copper port supply EGE BEES 2 SFP 1 copper ports 399 432 hours 218 384 hours 79 977 hours 1 SFP 1 copper ports 410 188 hours 221 560 hours 80 399 hours SC ST 1 copper ports 361 190 hours 206 434 hours 78 317 hours MTBF 2 copper ports No Power supply POE POE 2 SFP 2 copper ports 317 119 hours 191 244 hours 76 026 hours 1 SFP 2 copper ports 323 861 hours 193 675 hours 76 407 hours SC ST 2 copper ports 292 529 hours 182 017 hours 74 524 hours Fiber Optic Specifications 2 Port Models PoE P Wavelength TX Power RX Power PoE PP Mode nm dB dB Budget S 1110P M2xx05 MM TX 850 Min 9 5 Min 17 75 S 1110PP M2xx05 RX 850t Max 4 Max 3 i S 1110P S2xx10 SM TX
22. rnet parameters on the fiber connection This will ensure that the most optimal connection parameters will be in effect If connecting to another Perle Media Converter this parameter should be set to Auto The Media Converter Module will advertise 1000Mbps Full and Half Duplex no Pause Off The Media Converter Module s fiber will be fixed to 1000Mbps Full Duplex Note Fiber port 2 is always set to Auto When using a 100 Mbps SFP module Full Half Duplex on Fiber Switch 6 Switch Fiber 1 Fiber 2 Position 100 Mbps 100 Mbps Up default Full Duplex Full Duplex Down Half Duplex Full Duplex 12 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Full Duplex The Media Converter Module will be set to Full Duplex mode on its fiber link Half Duplex The Media Converter Module will be set to Half Duplex mode on its fiber link Loopback Fiber 1 Switch 7 Loopback Fiber 2 Switch 8 Switch Position Mode Up default Disabled Down Enabled Disabled The loopback feature is disabled This is default position for normal operation The switch must be set to this position in order for data to pass through the media converter Enabled This is a test mode All data received on the receive RX fiber connection is looped back to the transmit TX fiber connection The data link will be disabled however power to the powered devices will be maintained This mod
23. tects the signalling on the 10 100 1000BASE T interface to determine the type of cable connected straight through or crossover and automatically configures the connection Pause IEEE 802 3xy Integrated Pause signalling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed with data The Perle media converter can generate and respond to Pause messages If Auto negotiation is set to On the media converter will advertise symmetrical and asymmetrical pause If Auto negotiation is set to Off the Pause receive and send will be disabled Perle PoE PoE 10 100 1000 Ethernet Media Converter 21 Installation Guide Troubleshooting General 1 Ensure power is supplied to the media converter Only the Perle provided power supply may be used 2 Ensure the remote device s fiber connection type is compatible with the media converter If using a simplex fiber connection ensure that you have both an Upstream U and Downstream D media converter 3 Ensure all cabling is of the correct type and is in good working order 4 For duplex fiber connections ensure the RX and TX has been reversed between the two media converters No connectivity If unable to get full connectivity with all DIP switches in the UP position this procedure is recommended for troubleshooting Method 1 1 Set the Link Mode to Standard on both media converters Leave all other
24. ver the Ethernet cable see PSE function on Dip Switch configurations The wire pairs on the cable used for delivering power will depend on the device The following options are available PoE Option RJ 45 Alternative A Alternative B Legacy 1 positive 2 positive 3 negative 4 positive negative 5 positive negative 6 negative 7 negative positive 8 negative positive UTP copper Power PoE e IEEE 802 3af PoE up to 15 4 Watts per UTP port PoE e IEEE 802at 2009 PoE e Up to 30 Watts on a single UTP port model and up to 25 5 Watts per port on a dual UTP port model e PoE models will also support 802 3af PDs Type 1 and PoE PDs Type 2 6 Perle PoE PoE 10 100 1000 Ethernet Media Converter Installation Guide Powering Options Jumper Settings In order to select a powering option the Power Options Jumper settings must be set Each copper port has a set of Power Option jumpers To access the Powering Options Jumper settings unscrew the six side screws on the case and remove the cover plate Locate the Power Option jumper set and strap the option pins as detailed below Alternative A wep SPA ce ice a Legacy ee Perle PoE PoE 10 100 1000 Ethernet Media Converter 7 Installation Guide DIP Switches The DIP switches are accessible through the opening in the side of the enclosure Bank 1 Bank 2 Bank 1 1 Auto Negotiation copper 2 Li

Perle Systems S-1110DP User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents