Perfectone Net Ware GW-200 User's Manual
Contents
1. use service is checked please put the URI of gatekeeper into service addr The default service port is 1719 If the gatekeeper has a GKID please put it into service id If use service is not checked to make calls through gateway please put the URI of the gateway into service addr To make P to IP call please clear this field In both cases the default service port is 1720 e nat traversal When the gateway with private IP address need communicate with other IP phones in a different LAN or on Internet please select an item from dropdown list to set the proxy used by the gateway disable Select this item when the log in server and gateway in the same LAN or the log in system supports the gateway working behind the LAN enable When the system does not support gaeway working behind the LAN please select this item to search public IP address of the NAT device With this item selected nat addr field will be activated Besides port mapping port forwarding needs to be properly set up on NAT device citron With Citron private protocol used select this item to fit into the GnuGK system transferring the voice and signal by router a auvtech Select this item with Auvtech private system used a vida Select this item with Vida private system used a aivgr Select this item with aivgr private system used e nat addr When nat traversal is set to enable please put the 12 GW 202. 202 96 128 68 a o0 0d ea 00 00 03 protocol settings use service Vv register ttl 7680 jitter size service type common y service addr 203 935 9 5 service id nat traversal citron y nat addr OoOO O nat ttl phone number ez318801 account kinnon pin register port E signal port 1734 control port 50000 dtmf control string y dtmf payload 01 rtp port 0000 local type faccount x call type advanced y rtp tos phone settings 3 TE use dialplan disable dial number dddcode iddcode 886 iddprefix dddprefix inner line enable y innerline prefix dual mode disable gt dualmode prefix ring type atat y use digitmap forward number Po 7 fwd poweroff fwd always E fwd busy call waiting fwd noanswer m answer 30 audio settings vad Vv age VV aec Y codecl e729 y codec2 gT231 y codec3 codecd fella codecS esn g 723 1 high rate Vv audio frames fo fea handset in 0 15 ls handset out 0 31 other settings password 1234 super password 12345678 debug no check y sntp ip fo 0 0 0 use daylight in upgrade addr timezone GMT 08 00 Beijing Hong Kong Urumqi y Save Settings Address Book Upgrade Firmware Fig 3 1 Http Setting tte T mii speaker out 0 31 20 Network Setting network settings iptype static y ppp id festi Ppp pin festi local ip 192 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 196 115 dns2 202 96 128 68 mac 00 09 45 63 17 d8
3. disable e Update Click this button to save the configuration and the phone will reboot Once the phone reboots successfully the new configuration is effective Note After entering set page if Update button is not clicked within 5 seconds then when you click it again the index page asking for pin will pop up again Then please input the password again to enter the set page and then click Update button to confirm the modification Phone Book Click this button to open the speed dial settings page Please refer to Fig 3 7 In this page you can set and save the speed dial number by 20 GW 200 User Manual typing the name into the Name field and then entering the corresponding number following the name For example input Jack in Name field following 001 and then input 5989426454 into Phone number field Then Jack s number 5989426454 is saved in phone book Then please click Save Back button In normal state you can use speed dial to call numbers saved in phone book Phone Book Ho Hame Phone Humber Ho Name Phone Number 001 Tack 5989426454 002 Allen 192 168 1 56 E jit A A as fit O OO OOO O of jit yoy jy of E o M jit Fig 3 8 Phone Book Illustration Upgrade Program Click this button to update the program of gateway Before updating please fill IP address of FTP server into upgrade addr field and then click this button Then the gateway will read the corresponding bin files from the server and then loa
4. e codec4 Set the priority 4of the audio compression algorithm options are g729 g7231 g711u g711a and gsm e codec5 Set the priority 50f the audio compression algorithm options are g729 g7231 g711u g711a and gsm The The The The The e g 723 1 high rate enable disable g 723 1 high rate G723 1 high rate is 6 3kbps low rate is 5 3kbps e audio frame Set audio frames in RTP package Minimum is 1 and maximum is 8 e handset in Drag the slider to adjust the volume of handset input Drag it to the left to reduce the volume while drag it to the right to increase the volume e handset out Drag the slider to adjust the volume of handset output e speaker out This setting no needed to set at this moment Other settings 18 GW 200 User Manual other settings password 1234 super password 12345678 debug output v sntp ip 210 59 157 10 use daylight E upgrade addr timezone GNT 08 00 Beijing Hong Kong Urumqi i Fig 3 6 Other Setting e password Set the password of the phone Default password is 1234 esuper password Set the super password of the phone Default super password is 12345678 e debug Set the debug level of the phone a disable Disable output the debug message by selecting this item output Output the operation information to the window such as register input by selecting this item output all Output all debug information and data in test window by selectin
5. e fwd poweroff Forward calls if power off by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd noanswer Forward calls without replying by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd always Forward all calls by checking this box Please enter receiving forwarded calls phone number into fwd number field e fwd busy Forward calls if busy by checking this box Please enter receiving forwarded calls phone number into fwd number field e answer Enter a number from O through 60 to set the entries of the seconds before the phone answer the call auto or forward the calls Audio settings audio settings vad Iv age O aec IV codecl e7231 y codec2 e729 y codec3 2711u y codecd gsm Y codecS null y z 123 1 high rate v audio frames gt handset in fr handset out po speaker out po Fig 3 5 Audio Setting 17 GW 200 User Manual e vad Enable disable VAD voice activity detection e agc Check for enable the Auto Gain Coctrol e aec Check for enable Auto Echo Cancellation e codeci Set the priority 1of the audio compression algorithm options are g729 g7231 g711u g711a and gsm e codec2 Set the priority of the audio compression algorithm options are g729 g7231 g711u g711a and gsm e codec3 Set the priority 30f the audio compression algorithm options are g729 g7231 g711u g711a and gsm
6. negotiate about MD5 or CAT authentication system 3 use MD5 authentication account and pin 4 use CAT authentication account 30 GW 200 User Manual and pin 5 use SHA1 authentication account and pin set dtmf X Set DTMF relay type X is ranged form O through 3 O control string 1 inband audio 2 signal keypad 3 rfc 2833 set dtmf payload X When dtmf X select 3 rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 set dialplan X Enable disable dial plan and dial number Parameter X ranged from O through 4 0 disable dial plan 1 enable dial plan 2 use dial number 3 use 179XX service 4 use hotline function set dialnumber XX When set dialplan value set as 2 please use this command to set dial number For example with eTalk card used please set it as 00 When set dialplan value set as 4 please use this command to set hotline number set dddcode XX Set the area code when set dialplan value set as 1 or 2 For example the area code of Beijing is 10 the area code of Shanghai is 21 and the area code of Chengdu is 28 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set iddcode XXX 31 GW 200 User Manual Set the country code when set dialplan value set as 1 or 2 For example the country code of China is 86 the country code of USA is 1 etc Parameter xxxx must be an Arabic numeral and no longer than 4 characters set
7. Fig 3 2 Network Setting e iptype Set how gateway gets relevant network parameters by selecting corresponding item from drop down list Static ip Select this item to authorize users set IP address subnet GW 200 User Manual mask and router IP address of gateway manually dhcp Select this item to enable DHCP mode With this system your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on GW 200 Gateway is shipped from the factory with DHCP on So if you re LAN or router is configured to use DHCP addressing the gateway s LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up pppoe Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on modem If the gateway used with modem please select this item to get relevant network parameters auto Then please fill ID and pin into ppp id and ppppin fields e ppp id With pppoe or modem selected in iptype drop down list please enter the user name here e ppp pin With pppoe or modem selected in iptype drop down list please enter the password here GW 200 User Manual e local ip With static ip selected in iptype drop down list please enter IP
8. iddprefix XX Set IDD service prefix number when set dialplan value set as 1 or 2 For example IDD service prefix number of china is 00 IDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set dddprefix XX Set DDD service prefix number when set dialplan value set as 1 or 2 For example DDD service prefix number of china is 0 DDD service prefix number of USA is 1 etc Parameter xxx must be an Arabic numeral and no longer than 3 characters set innerline X Set use innerline call or not X ranged from 0 through 1 0 disable 1 enable innerline call set innerlinepreifx X With innerline set as 1 enable please set the prefix to pick up inner line such as 0 set answer X Set the ring seconds before the phone answers the call auto or forward the calls X is ranged from O through 60 32 GW 200 User Manual set ringtype X This setting no need to set at moment set digitmap X Set whether to use digitmap X ranged from 0 to 1 0 do not use digitmap 1 use digitmap set fwdnumber XXXXXXX Set receiving forwarded calls phone number XXXX must be an Arabic numeral and no longer than 16 characters set fwdpoweroff X Enable disable forward calls if power off X is ranged from 0 through 1 0 do not forward calls if power off 1 forward call if power off set fwdalways X Enable disable forward all calls X is ranged from 0 through 1 0 do not forward all c
9. priority 3 of the audio compression algorithm X is range from 0 through 4 0 g729 1 97231 2 g711u 3 g711a 4 gsm set codec4 X Set the priority 4of the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec5 X Set the priority 5 of the audio compression algorithm X is range from 0 through 4 0 g729 1 97231 2 g711u 3 g711a 4 gsm set password XXXX Set password of the GW 200 Gateway XXX must be ASCII characters set superpassword XXXX Set super password of the GW 200 Gateway XXX must be ASCII characters 35 GW 200 User Manual set debug X Set open debugging message output grade for special tool X is ranged from 0 through 5 0 close debugging output 1 output the operation information to the window 2 output all the bug information and data in test window 3 save the bug information into SDRAM 4 disable checks the mark set upgradeaddr XXX XXX XXX XXX Set IP address or domain name of FTP server supplying upgraded program of GW 200 set nt XXX XXX XXX XXX No needed to set for the Gateway GW 200 set daylight X No needed to set for the Gateway GW 200 set timezone XX No needed to set for the Gateway GW 200 Command store Syntax description no keyword Parameter ranged from 0 through 4 Usage Save the current settings to the designated position Relevant Usage store 1 Command load Syntax description no keyword Parameter range
10. will boot up It takes 30 seconds until the Gateway is in working mode Please press IP SET key and pick up the phone s handset you should be able to hear dial tone or busy tone Now let us configure it 1 If you are using DHCP IP addressing Please pick up the phone press 12341 then press the IP SET key on the gateway and hang up the phone GW200 will then reboot and connect to DHCP server to get the IP address After 30 second press the IP SET key and then pick up the phone you will hear the voice prompt from the handset telling you the current IP address of the gateway 2 If you are not using DHCP IP addressing If your LAN does not use DHCP addressing each device concurrently connected to it must be assigned its own unique IP address To allocate an IP address for GW 200 for example 192 168 1 100 please pick up the phone press 12340 then press the IP SET key on the gateway and hang up the phone After the 3 GW 200 User Manual gateway has finished rebooting it will be in static IP mode Then you pick up the phone again press 1234 192 168 1 100 then press the IP SET key on GW 200 and hang up the phone Gateway will reboot again Now the phone s IP address is 192 168 1 100 if you want to check it please refer to the item 1 Features Hardware Main chip pa1688 50MHz Data Memory 2MB SDRAM Program Memory 1 MB Flash memory Ethernet Jack 10 100M jacks AC DC adapter Inp
11. 0 User Manual Installation 1 Connect handset to base insert handset cord into handset cord jack at the left side of the base 2 Connect Gateway to Internet plug the RJ 45 Ethernet cable into the Ethernet Jack Plug the other end of the cable into HUB 3 Power on Gateway plug the power cord adapter into the Power Jack Then plug the other end of the power cord adapter into the appropriate wall outlet GW 200 User Manual Configuration To configure GW 200 you can use web browser and Telnet commands Configure by Web browser After you ve got the local IP address of the gateway from the voice prompt On a PC connecting with the gateway or at the same segment of the gateway double click ES icon to open the IE browser Input the IP address of the gateway into address bar Address l 192 168 1 100 and then input password of the gateway into the following page Default password 1234 is ordinary password Then clickL___1szin___ button The following configured page will popup Input the data by your computer s keyboard according to your LAN parameters under the network settings protocol settings phone settings and audio settings When finished click update and quit the screen GW 200 User Manual network settings iptype dhcp ppp id PPP pin A local ip 192 168 1 100 subnet mask 255 255 255 0 router ip 192 168 1 254 as 202 106 4615 dos2
12. 0 User Manual domain name of the servers These web server helps to find out the public IP of the IP phone into nat addr such as www whatismyip com e nat ttl When gateway sit behind a NAT device it will send packets to server every nat ttl seconds to keep the port mapping on the NAT device alive nat ttl is an integer between 10 and 65535 default value is 20 e phone number The local phone number or username of this phone usually is allocated by system e account While calling card is set please type the account of chosen card into this field while md5 account item selected in local type dropdown list enter ID here while account is selected in local type dropdown list enter ID here While prefix item selected in use dialplan dropdown list enter language indicating number card number and here such as 14589653185 e pin While calling card is set please type the password of chosen card into this field while md5 account item selected in local type dropdown list enter password here While prefix item selected in use dialplan dropdown list enter password and here such as 3185 e register port The local UDP port registered with server to accept incoming handshaking messages any number between 1024 and 65535 is acceptable e signal port This port is Q 931 port using TCP protocol can be any number between 1024 and 65535 e control port This port is H 245 port using TCP protocol can be a
13. 02 registerttl 60 rtptos 0 rtpport 6802 jitter size 0 calltype 1 advanced localtype O phonenumber dtmf O control string dtmfpayload 101 dialplan 2 dialnum dialnumber 17911 dddcode empty iddcode empty iddprefix empty dddprefix empty innerline 1 enable innerlineprefix empty digitmap O disable dualmode O disable callwaiting O disable answer 5 ringtype O dtmf0 fwdnumber empty fwdpoweroff 1 enable fwdalways O disable fwdbusy O disable fwdnoanswer O disable audiotype 0 g7231 audioframes 1 6 3k 1 enable vad 1 enable agc O disable aec 1 enable handsetin 9 handsetout 21 speakerout 21 codec1 1 g7231 codec2 0 g729 codec3 2 g711u codec4 4 gsm codec5 5 null password 1234 superpassword 19750407 debug 1 output upgradeaddr empty sntpip 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumadi Input ordinary password with debug set as O disable following information will be seen GW 200 V1 40 settings 24 GW 200 User Manual Password P gt get iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns2 202 106 196 115 nattraversal 1 enable nataddr rtpport 5144 registerport 5142 signalport 5142 controlport 5144 account empty pin empty phonenumber 182378009 fwdpoweroff O disable fwdalways O disable fwdbusy O disable fwdnoanswer O disable ringtype O dtmf0 answer 5 password 1234 upgr
14. PO a g A IS ER ECTONE GW 200 VoIP Gateway User Manual GW 200 User Manual e Breif Introductin of GW 200 VoIP GiatwwWay oooccocccnccnccnconcnncnncnncnnconcnnnoncnncnns 3 Features ja ce ts loseh ce he ead ei eal ha E Pes eee a dbo ee dees 4 e Standard and Protocol cc cccceceec cece cece a e aa aa rE a EEE aas 4 e Operating requirements ocoococccccccccncoconconnncncononconnnnoncnnoncncnnnncnnnnronininennnnnns 5 e Electric requireMents ocooconconcoconcconcnnnoncnncnnnnncnnconnonronrnnrnncnnnnnrenrnnrnnnnnnnn 5 OSI a a E cds dia sorda 5 e Installation ios debi 6 COMPQUIFALION ui atari 7 e Configure by Web broWer ooooococcccncoccccoccnccnononconcnconcnncnconnnenconincnnnncnnnnnncinines 7 Telnet Configura A A 21 e Placa ld dial eo 38 GW 200 User Manual Breif Introduction and how to start information GW 200 VoIP Gateway functions as an analog adaptor with an ordinary telephone lt has a power adapter interface an RJ45 interface an RJ11 interface and an IP SET key RJ45 interface is used to connect to LAN and RJ11 interface is used to connect the phone The IP SET key is to initiate the voice prompt stored to announce the local IP address to enter safe mode to retrieve the firmware and to set the IP type and IP address To start please connect your GW 200 VoIP Gateway with the LAN a phone and the power supply properly see the following picture The GW 200
15. User Manual phone settings use dialplan disable y dial number A dddcode gt iddcode 886 iddprefix dddprefix e inner line enable x innerline prefix dual mode disable y dualmode prefix ring type atn y use digitmap F call waiting D forward number Po fwd poweroff fwd noanswer F fwd always F fwd busy r answer fo Fig 3 4 Phone Setting e use dialplan Set whether use dial plan or use dial number by selecting the corresponding item in drop down list a disable Do not use dial plan or dial number by selecting this item enable Use dial plan by selecting this item dialnum Use dial number by selecting this item With this item selected please enter the dial prefix into dial number field prefix Use 179XX service by selecting this item Hotline Use Hotline function by selecting this item With this item selected please enter the hotline number into dial number field Note With 179xx service used please set as follows fill call prefix into dial number field such as 17930 type language indicating number card number and into account field fill password and into pin field e dial number With dialnum selected in use dialplan drop down list please enter the dial prefix into this field according to requirement of log in server For example with eTalk card used enter 00 here e ddd code With enable or dialnum selected in use dialplan drop down list set area code according to E 164 dial rule For
16. address of gateway here e subnet mask With static ip selected in iptype drop down list please enter subnet mask of Gateway here router ip With static ip selected in iptype drop down list please enter router IP address of Gateway here e dns With static ip selected in iptype drop down list please enter IP address of DNS server here e dns 2 With static ip selected in iptype drop down list please enter IP address of backup DNS server here mac MAC address is the physical address supplied by the Ethernet NIC GW 200 gateway is shipped from the factory with a unique algorism MAC address printed on the back of the base Protocol Setting protocol settings use service Vv register ttl 15390 jitter size fo service type common gt service addr f203 93 9 57 service id 7 nat traversal citron y nat addr ss nat ttl o phone number jor account DOO y pin oe register port fito gt signal port jiT20 control port i722 dtmf control string y dtmf payload 101 rtp port i722 local type faccount y call type advanced y rtp tos o Fig 3 3 Protocol Setting e use service Enable disable service by checking clearing this box To make calls through gatekeeper please check this box otherwise gateway can only make IP to IP calls 10 GW 200 User Manual register ttl The gateway will send a keep alive registration message to gatekeeper every register ttl seconds The value range is 10 65535 Def
17. adeaddr empty sntpip 0 0 0 0 daylight O disable timezone 55 GMT 08 00 Beijing Hong Kong Urumadi Command set Syntax description set keywords value Usage Used to configure password and other running parameters of GW 200 gateway Detailed description set iptype X Set how gateway gets relevant network parameters X ranged from 0 through 3 0 authorize users set IP address subnet mask and router IP address of gateway manually 1 use DHCP mode With this system your LAN or router automatically assigns all the required network parameters to any device connected to it when the device log on GW 200 gateway is shipped from the factory with DHCP on So if your LAN or router is configured to use 25 GW 200 User Manual DHCP addressing the gateways LAN parameters will automatically be configured as soon as it is connected to the LAN or router and powered up 2 use PPPoE mode Those ADSL and Cable Modem users please select this item for it is a protocol especially designed for them With this system ADSL ISP automatically assigns all the required IP parameters to any device connected to it when the device log on 3 use modem mode Those who use gateway with modem please set the value as 3 set pppid XXX With iptype set as 2 use this command to set ADSL ID with iptype set as 3 use this command to set Modem ID set ppppin XXX With iptype set as 2 use this command to set ADSL pin with iptype set as 3 use this comman
18. all with Fix IP Address If GW 200 Gateway which with the Fix IP address and without used the Gatekeeper service you can place a call to which also with Fix IP and without used the Gatekeeper service Pick up the handset and then entering the IP address with the number key pressing the key as a dot and press the key end the dialing Wait for the other party answer When the call is finish put back the handset e Dial out the number from phone book Pick up the handset and listen for the dialing tone Pressing the and then press the Phone Book memory number 2 digits Then pressing the key to end the dialing The Gateway will automatically dial out the number which stored before Perfectone Website at www perfectone net Copyright 2005 Perfectone Net Ware Company Limited All right reserved 39
19. alls 1 forward all calls set fwdbusy X Enable disable forward calls if busy X is ranged from 0 through 1 0 do not forward calls if busy 1 forward call if busy set fwdnoanswer X Enable disable forward calls without replying X is ranged from 0 through 1 0 do not forward calls without replying 1 forward call 33 GW 200 User Manual without replying set audioframes X Set audio frames in RTP package X is Arabic numerals between 0 and 7 set 6 3k X With G 7231 set PA168X IP phone to use 6 3K rate or not X is ranged from 0 through 1 0 use 6 3K rate 1 use 5 3K rate set vad X Enable disable VAD X is ranged from 0 through 1 0 disable VAD 1 enable VAD set agc X Enable disable AGC X is ranged from 0 through 1 0 disable AGC 1 enable AGC set aec X Enable disable AEC X is ranged from 0 through 1 0 disable AEC 1 disable AEC set handsetin X Set initial volume of handset X is ranged from 0 through 15 set speakerin X Set initial volume of microphone of the base X is ranged from 0 through 15 set handsetout X 34 GW 200 User Manual Set initial volume of handout X is ranged from 0 through 31 set codec X Set the priority 10f the audio compression algorithm X is range from 0 through 4 0 g729 1 g7231 2 g711u 3 g711a 4 gsm set codec2 X Set the priority 2 of the audio compression algorithm X is range from 0 through 4 0 g729 1 97231 2 g711u 3 g711a 4 gsm set codec3 X Set the
20. ault is 60 jitter size Set buffer size of RTP package The value range is 0 32 service type This option is used to accommodate the miscellaneous requirements of the system providers When gateway is connected to these systems please select the corresponding service type 4 9d gt 4 4 Common no special requirements Mediaring use Mediaring prepaid card Etalk use etalk prepaid card When this is selected please select dialnum from the Use dialplan list box and put 00 into dial number Auvtech use Auvtech s system When connected with Auvtech s system please select auvtech from the nat traversal list box select account from the local type list box Subcentrex Use Subcentrex s system Ringtec Use Ringtec s system When this is selected please select dialnum from the Use dialplan list box and put Ringtec account into dial number Smartcon Use Smartcon s system Dda Use Dda s system Vida Use Vida s system Citron Use Citron s system Asiasoft Use Asiasoft s system Huawei Use Huawei s system Asiainfo Use Asiainfo s system Lucent Use Lucent s system GW 200 User Manual IPN Use IPN s system Yiyang Use Yiyang s system Thinker Use Thinker s system Suntek Use Suntek s system e service addr service id Please put the URI domain name IP address of the server into service addr If
21. d from 0 through 4 Usage Load the designated settings to the current position Relevant Usage load 1 Command exit 36 GW 200 User Manual Syntax description no keyword and parameter Usage Exit from Telnet command window without saving the configuration Relevant usage None Command write Syntax description No keyword and parameter Usage Save the configuration and restart the GW 200 gateway Command ping Syntax description ping IP address Usage ping IP address of other NAT device Relevant usage In telnet window input ping xx xxx xx xx an IP address and return then the result will be displayed If the address is effective ping OK will be seen if the address is ineffective nothing will be seen Fox example P gt ping 203 93 9 57 P gt ping OK P gt ping 27 56 120 56 P gt Note Usually the echo time of ping command is no more than 1 second So if the result is not displayed in 5 seconds ping command is fail ftp command Syntax description ftp value Usage the system connects to the FTP server auto to get the corresponding file and deal with it Relevant usage ftp X X ranged from 0 through 2 37 GW 200 User Manual X 0 Connect to FTP Server to get the file of updating program and save it to the SDRAM of the gateway Then the file can be read by PalmTool This operation aims at testing X 1 Connect to FTP Server to get the file of updating program and u
22. d into the gateway Update Digitmap Click this button to update the digitmap of the gateway Before updating please fill IP address of FTP server into upgrade addr field and then click this button Then the gateway will read the corresponding map files from the server and then load into the gateway gt Telnet Configuration e On the PC choose Start gt Run and then type telnet 192 168 1 100 into Run field in popuping Run dialog Or input telnet 192 168 1 100 in the DOS window Then the following information will be displayed GW 200 V1 40 settings Password Then please type password With debug is set as O disable if type ordinary password default one is 1234 after Retun you will see Password 21 GW 200 User Manual P gt If you type super password then you will see Password a kkkkkkkk P gt Above information indicates that gateway is under setting mode and then you can set the GW 200 gateway by using the telnet commands gt GW 200 Gateway Telnet Commands Explanation GW 200 gateway Telnet Commands Command Function Supply command name and parameters get Display basic parameters of the GW 200 gateway set Set parameters of the GW 200 gateway store Save current settings to designated position load Load designated settings to current position exit Exit from the setting mode without saving the configuration write Exit with saving all configurations and restart GW 200 gateway ping Pin
23. d to set Modem pin set ip XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of gateway set subnetmask XXX XXX XXX XXX With iptype set as 0 use this command to set subnet mask of gateway set router XXX XXX XXX XXX With iptype set as 0 use this command to set router IP of network 26 GW 200 User Manual with gateway set dns XXX XXX XXX XXX With iptype set as 0 use this command to set IP address of DNS server set dns2 XXX XXX XXX XXX With iptype set as 0 use this command to set IP of backup DNS server set mac XX XX XX XX XX XX Set MAC address of the GW 200 gateway Parameter XX XX XX XX XX XX must be an HEX number set service X Set register the gatekeeper or not X ranged from O through 1 0 do not register 1 register set service type X Enable disable the repaid and service system choose the repaid server provider Parameter x ranged from 0 through 29 0 common disable repaid card 4 use Mediaring service 2 use eTalk card 3 use Auvtech system 5 use Ringtec service 6 use Smartcon service 7 use dda service 8 use vida service 9 use citron system 10 use asiasoft system 12 use zte system 13 use huawei system 16 use asiainfo system 17 use Lucent system 19 use IPN system 20 use yayuang system 21 use 27 GW 200 User Manual thinker system 22 use suntek system 28 use txtc system set serviceaddr XXXX Set IP address or domain name of gatekeeper set
24. example 15 GW 200 User Manual Beiing 10 Shanghai 21 e idd code With enable or dialnum selected in use dialplan drop down list set country code according to E 164 dial rule For example China 86 U S A 1 e idd prefix With enable or dialnum selected in use dialplan drop down list set international call prefix according to E 164 dial rule such as 00 e ddd prefix With enable or dialnum selected in use dialplan drop down list set long distance call prefix according to E 164 dial rule such as 0 Note With dialnum seletcted in use dialplan drop down list you can also set dddcode iddcode iddprefix and dddprefix according to requirement of system e innerline Enable disable innerline call by selecting corresponding items from dropdown list a disable Disable call innerline by selecting this item a enable enable call innerline by selecting this item einnerlineprefix With enable selected in innerline dropdown list please fill the number prefix to pick up innerline such as 0 e Dual mode This setting no need to set at moment 16 GW 200 User Manual e Dualmode prefix This setting no need to set at moment ring type This setting no need to set at moment e Use digitmap Enable disable digit map by checking unchecking the box e Call waiting Enable disable call waiting by checking unchecking the box e forward number Enter receiving forwarded calls phone number into this field
25. g other net parameter ftp The gateway connects to FTP server and then get the files Detail description of GW 200 Telnet commands Command Syntax description No optional parameter Usage Type command name and parameters following P gt Be used as the keyword to supply keyword and parameters of the relevant commands Relevant usage None 22 GW 200 User Manual Detailed description 2 List help of all commands For example P gt set get list settings store x store current to xth settings load x load xth settings to current exit write save settings Command get Syntax description No optional parameter of keywords Usage Display basic parameters of the GW200 gateway Relevant usage None Detailed description get Display basic running parameters of the GW 200 geatway Input ordinary password without debug being set as O disable or input super password with debug set as O disable then following parameters of gatway will be displayed GW 200 V1 40 014 settings Password P gt get iptype O static ip 192 168 1 100 subnetmask 255 255 255 0 router 192 168 1 254 dns 202 106 196 152 dns2 202 106 196 115 mac 00 09 45 65 a3 e6 service 1 enable servicetype O common serviceaddr 203 93 9 57 serviceid 23 GW 200 User Manual empty nattraversal 1 enable nataddr www showmyip com natttl 30 phonenumber 182378009 account empty pin empty registerport 6800 signalport 6800 controlport 68
26. g this item remote debug Save the debug information in SDRAM of IP phone by selecting this item a no check Disable checking firmware tags when upgrading This is not suggested because it will increase the risk of upgrading the wrong firmware into the phone e upgrade addr Put IP address or domain name obtained by ISP of FTP server supplying upgrade program into this field e nts ip No needed to set for the Gateway GW 200 19 GW 200 User Manual e use daylight No needed to set for the Gateway GW 200 e timezone No needed to set for the Gateway GW 200 When debug set as O disable if input ordinary password default one is 1234 then following page will pop up after clicking Cms And only those parameters can be modified network settings iptype dhcp ppp id o PPP pin o local ip f192 168 1 212 subnet mask 255 255 255 0 router ip 192 168 1 254 dns 202 106 46 151 dns2 202 96 128 68 protocol settings nat traversal citron y nat adr phone number jor account SSS rtp port i722 register port fito gt signal port rrao control port i722 phone settings ring type atnzo y forward number 82378009 fwd always fwd noanswer v fwd poweroff C fwd busy F answer ao other settings password j2 upgrade aaf sntp ip 210 59 157 10 use daylight i timezone GMT 08 00 Beijing Hong Kong Urumqi Save Reboot Address Book Upgrade Firmware Fig 3 7 Setting Page using ordinary pin with Debug set as 0
27. ger than 16 characters set account XXXXXX While calling card is set set account of chosen card while local type is set use authentication type set user ID while set localtype is set as 1 set ID set pin XXXXXXXXXX While calling card is set set password of chosen card while local type is set authentication type set password set registerport XXXX Set register port XXXX is range from 1024 through 6553 set signalport XXXX This port is Q 931 port using TCP protocol XXXX is range from 1024 through 65535 set controlport XXXX 29 GW 200 User Manual This port is H 245 port using TCP protocol XXXX is range from 1024 through 65535 set registerttl X Set register TTL X is range from 10 through 65535 Sec default value is 60 Sec set rtptos X Set TOS segment of IP head package in RTP digital follow set rtpport XXXX RTP port is the port transferring and receiving voice flow using UDP protocol XXXX is range from 1024 through 65535 set jittersize X Set buffer size of RTP package X is range from 0 32 set calltype X Set call type of the phone X is ranged from 0 through 2 0 call out in normal way 1 call out in faststart and tunneling way It is a recommended way set localtype X This command used to set how gateway log in gatekeeper X is ranged from 0 through 6 0 use phone number as E 164 and ID to login the GK 1 use phone number as E 164 and designated ID by set account XXX command 2 use support automated
28. ny number between 1024 and 65535 e dtmf Set DTMF signal sending way by selecting control string inband audio signal keypad or rfc 2833 from list box e dtmf payload When DTMF select rfc 2833 This parameter can be used indicating type of RTP payload type The value can be use integer 96 101 e rtp port RTP port is the port transferring and receiving voice packets using UDP protocol This is an even number between 1024 and 65535 13 GW 200 User Manual can t be the same as register port e local type This parameter refers to how gateway authenticate itself to the gatekeeper The meaning of each item is as follow m phone number Use phone number as E 164 and ID to login the GK n account Use phone number as E 164 and designated ID filled in account field as ID to login GK 7 auto Use support automated negotiate authentication account and pin about MD5 or CAT a md5 Use MD5 authentication account and pin m cat Use CAT authentication account and pin m sha1 Use SHA1 authentication account and pin call type Set call type by selecting the items in drop down list normal Call out in normal way by selecting this item a advanced Call out in faststart and tunneling way by selecting this item It is a recommended way with protocol used e rtp tos Set the TOS field of the IP header of the RTP packets The bigger this value is O the higher priority the packet is phonesettings 14 GW 200
29. pdate program Flash This operation aims at updating program X 2 Connect to FTP Server to get the file of updating dial rules and update program Flash This operation aims at updating dial rule Note When you use ftp O and ftp 1 commands if the file get from FTP server is too large or the net speed is too slow then the process will not be seen in telnet window Please be patient Using ftp command in telnet to get file soends almost same minutes as getting file using gateway So if nothing is displayed after too long time it means that ftp is fail Note All the Telnet commands of GW 200 gateway should be written in low case and the password is case sensitive gt Usage of the phone gt Receiving calls GW 200 gateway can receive incoming calls from other IP Phone or another IP Gateway which and support the protocol It works just like an ordinary phone When it rings pick up the handset to answer the incoming calls and finish put the handset back gt Place a call e Call another IP Gateway or IP phone under the same Gatekeeper Pick up the handset and listen for the Internet dial tone Then dial the phone number you wish to call and press to end the dialing Once the call connection has been established and the ring tone has sounded wait 38 GW 200 User Manual for the other party to answer When the other party answers you can begin speaking When the call is finish put back the handset e Place a c
30. serviceid XXXXX Set service ID according to required by service system set nattraversal X Set NAT traversal or not X ranged from 0 through 7 0 do not use When the log in server and gateway in the same LAN or the log in system supports the gateway working behind the LAN 1 Use NAT traversal When the login system does not support gateway working behind the LAN please use this value to search public IP address of the NAT device With this item selected please make port mapping on NAT device 2 With Citron private protocol used use this value to fit into the GnuGK system transferring the voice and signal by router 3 use this value with Innopath private system used 5 use this value with vida private system used 6 aivgr use this value with aivgr private system used 7 use this value with Eproxy private system used set nataddr XXXXX Set IP address of NAT device wan port or URI of free assistant service Such as www showmyip com etc in Internet NOTE The free service list of Internet www ip calculator com 28 GW 200 User Manual www ipchicken com www ipchicken com www showmyip com www whatismyip com www myipaddress com www whatismyipaddress com ip sbbs net www whatismyipaddress net checkip dyndns org set natttl XX Set NAT TTL XX is an integer between 10 and 65535 sec default value is 20 sec set phonenumber XXXXXXXX Set a phone number of GW 200 gateway Value xxxxx must be an Arabic numeral and no lon
31. ut AC 230V or 120V Output 9V DC 500mA Software DHCP support for LAN or Cable modem PPPoE support for ADSL or Cable modem Set phone by HTTP web browser IE6 0 or Telnet Upgrade by FTP Support major G 7XX and gsm610 audio codec VAD Voice Active Detect CNG Comfort Noise Generation Dynamic voice jitter buffer G 168 165 compliant 16ms echo cancellation Tone generation and Local DTMF re generation according with ITU T E 164 dial plan and customized dial rules Voice prompt Hotline Standard and Protocol GW 200 supports following standard and protocol e IEEE 802 3 802 3 u 10 Base T 100Base TX e Major G 7XX and gsm610 audio codec GW 200 User Manual e TCP IP Internet transfer and Control Protocol e RTP Real time Transport Protocol e RTCP Real time Control Protocol e VAD CNG save bandwidth e DHCP Dynamic Host Configuration Protocol e PPPoE Point to Point Protocol over Ethernet e DNS Domain Name Server e Telnet Internet s remote login protocol e FTP File Transfer Protocol e HTTP Hyper Text Transfer Protocol e Build in proxy Operating requirements e Operation temperature 0 to 50 C e Storage temperature 10 to 60 C e Humidity 10 to 90 no dew Electric requirements e Voltage 9V DC 500mA e Power adapter AC to DC Input 230VAC Output 9VDC Current 500mA e Network interface 1 RJ 45 Ethernet Connector e FXS 1 FXS Connector Size 152 x 115 x 32 mm LxWxH GW 20
Download Pdf Manuals
Related Search