Pelco EH8100 User's Manual
Contents
1. _ PRESSURE X RELIEF VALVE GROUND STUD Wy EEE Focus N LENS COM ZOOM IRIS HTR GROUND N 0 HTR 7 THERMOSTAT TABLE A FUNCTION COLOR VIDEO COAX CORE VIDEO COAX SHIELD PP 45V BLK WHT PP COM RED WHT CAMERA AC LINE BLU CAMERA AC NEUT VIO PS SWITCH GRN WHT AC LINE BLK PS SWITCH WHT GRN IRIS BRN FOCUS RED ZOOM ORG LENS COM YEL AC NEUTRAL WHT PP FOCUS YEL WHT PP ZOOM GRY WHT kk O PP zoom PP FOCUS DV PP COM Q QI PP sv NOTES Consult the manual section dealing with model number listings for the wattage and number of heaters for the particular model that you are using Terminal block only on the EH8106 The EH8104 does not have a terminal block for lens presets Figure 2 EH8100 Series Enclosure Wiring Diagram MATING CONNECTOR ASSEMBLY To assemble the 16 pin mating connector perform the following steps 1 Discard the white plastic sleeve that is included with the connector assembly Thread the cable through the compression nut strain relief and connector shell CONNECTOR SHELL COMPRESSION NUT AND STRAIN RELIEF 2 Prepare the cabling by doing the following Control Cable a Strip the outer jacket back 2 inches 5 cm b Stri2. VAC 230 VAC optional for heaters 40 watts EH8104 80 watts EH8106 16 pin receptacle with jam nut MS type connector supplied Distances are given in feet values in parentheses are meters EH8104 All Others 10 390 3 166 2 640 804 6 560 1 999 1 660 505 4 110 1 252 1 040 316 2 590 789 650 198 1 620 493 410 124 Two 20 watts each 120 VAC Two 40 watts each 120 VAC Heaters are thermostatically controlled to come on at 40 F 4 C and go off at 60 F 16 C Type 304 stainless steel Aluminum 6061 T6 Gray polyester powder coat Black anodized See Figure 3 gt inch diameter tempered glass 0 225 inch thick inch diameter tempered glass 0 225 inch thick o Multiple mounting holes on camera sled allow for linear adjustment 3 inch diameter x 14 inch length 8 x 35 cm or 14 L x 2 5 W x 2 5 H inches 35 x 6 x 6 cm 5 inch diameter x 18 inch length 13 x 46 cm or 18 L x 4 0 W x 4 0 H inches 46 x 10 x 10 cm Adjustable cradle secured with stainless steel bands Standard Schraeder valve to allow enclosure to be filled with dry nitrogen Prevents over pressurization of enclosure 8 lb 4 kg 15 Ib 7 kg Environmental Ambient Operating Temperature Vibration Altitude Acoustic Noise Humidity Ratings 40 to 122 F 40 to 50 C with heater 5 to 60 Hz with 0 082 inch total travel 15 g s at 60 Hz From 60 to 1 000 Hz 5 g s rms with random vibration Sea level to
3. equivalent of 10 000 feet Operates in 150 dB acoustic noise environments Up to 100 relative humidity Equipped with standard Schraeder and pressure relief valves to provide positive internal pressure with dry nitrogen Meets NEMA 6 IP 67 standards Design and product specifications subject to change without notice TEMPERED GLASS WINDOW A E E re ca G 1 4 20 NUT PRESS 2X i LL LY NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALLOTHERS ARE INCHES Figure 3 Dimensions C1407M G 12 04 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FT FR8000 Series fiber optic products and the following fixed camera models CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and CC3651H 2X Three years on all other fixed camera models including Camclosure Integrated Camera Systems and Genex Series multiplexers server and keyboard Two years on all standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM8500 CM9500 CM9700 Series Matrix DF5 and DF8 Series Fixed Dome products Two years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications
4. D 7 00 Revised manual to include grounding stud on rear plate C1407M E 1 04 Changed charging pressure from 5 psi to 8 psi 8 04 Removed agency logos and updated warranty and return information C1407M F 11 04 Factory preset for regulator changed to 12 psi per ECO 04 9807 Removed references to EH8108 and updated layout C1407M G 12 04 Revised instructions and artwork for mating connector assembly per ECO 04 10254 Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco Copyright 2004 Pelco All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
5. INSTALLATION OPERATION EH8100 Series Pressurized Camera Enclosure S e C1407M G 12 04 Contents Important Safety INSttUCtlOns soci parias ia a aa daa node 3 DESCrIPUONi s i i sedate LI i ie E i dr i 4 RA O EE E E E 4 Installation a meene ga O O it 4 MOUNTING uta ica ds e dl ogee E 4 Camerarand bensInstallation tacere rats as ai daa dt 4 Mating Connector AssemblV a A ic 6 Recharging INEENGIOS TE lt 3 a ire iena tei eleonora errare 7 POWEE CONMGCHOMN asar ann onde ATRIA teri ere Lead E eae aneud acne 7 Operati oo issseet drede orerar ni E TARRE DER ELORE ATENE ONEONE DENE PETR RES SRE EAER REEDD EEREN NE EN RERET REEN 7 Mantenance siti aiar 7 SEMVICING sin 8 Disable td acto ac 8 Recharging aNd REassemblV decidi arras rari 8 Specifications sp tidad A ara 9 List of Illustrations 1 EH8100 Series Enclosure Rear View 5 2 EH8100 Series Enclose Wiring Diagram resser a due as 5 3 DIMENSIONS oi RL pind LS sakes 10 2 C1407M G 12 04 Important Safety Instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has bee
6. T or EH80060RKIT To prepare the enclosure for recharging follow the steps below 1 Once the enclosure has been disassembled remove the O ring from the rear plate and install a new O ring in the O ring groove in the rear plate 2 When the new O ring has been installed in the rear plate smear a liberal amount of the O ring lubricant provided with the kit on the exterior surface of the O ring and rear plate Replace the desiccant bag in the enclosure with a new one provided with the kit 3 Slide the camera sled back into the body making sure the front lip of the sled is under the retaining bracket of the enclosure When fully installed the rear plate will fit firmly into the rear opening of the housing and the retaining groove will be fully visible 4 Reinstall the spiral retaining ring in the retaining groove in the rear of the enclosure 5 Recharge the enclosure Refer to the section Recharging The Enclosure for instructions 8 C1407M G 12 04 Specifications Electrical Input Voltage Power Requirements Connector Mating Connector Maximum Cable Distances 12 Awg 14 Awg 16 Awg 18 Awg 20 Awg Heater EH8104 EH8106 General Construction EH8106 26SS All other models Finish Outside Inside Dimensions Front Window EH8104 EH8106 Series Camera Mounting Maximum Camera Lens Size EH8104 EH8106 Enclosure Mounting Purge Fitting Purge Fitting Weight EH8104 EH8106 C1407M G 12 04 120
7. Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders and NVR300 Series network video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional
8. harging kit for EH8100 Series Kit includes pressure regulator and nitrogen PSKIT8100 Pressure sensor kit with contact closure that can be wired to trigger an alarm if enclosure s internal pressure falls below 5 psi C1407M G 12 04 7 Servicing DISASSEMBLY 1 Disconnect the power from the enclosure 2 Remove the mating connector from the rear of the enclosure by turning the outer ring counterclockwise until a click is felt then pull the mating portion of the connector off You may elect to remove the enclosure from its mount which will make the disassembly process much easier 3 Remove the center cap from the Schraeder valve Refer to Figure 1 4 Relieve internal enclosure pressure by depressing and holding down the center stem of the Schraeder valve A CAUTION Pressure must be released prior to opening the enclosure or personal injury may result 5 Remove the rear plate of the enclosure Refer to Figure 1 and do the following a Remove the spiral retaining ring from the back of the enclosure Use a screwdriver to pry the end of the spiral retaining ring from the retaining ring groove b Pull on the T handle to remove the rear plate from the housing RECHARGING AND REASSEMBLY Whenever the enclosure is disassembled for servicing it should be recharged after reassembly and prior to installation Recharging requires the use of a Pelco EH8000RKIT recharge kit or equivalent and applicable O ring kit part number EH80040RKI
9. n dropped 6 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 7 Use only installation methods and materials capable of supporting four times the maximum specified load 8 Only use replacement parts recommended by Pelco 9 After replacement repair of this unit s electrical components conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present A within this unit CAUTION RISK OF ELECTRIC SHOCK This symbol indicates that there are important operating and maintenance instructions in DO NOT OPEN the literature accompanying this unit C1407M G 12 04 3 Description Enclosures in the EH8100 Series are sealed and pressurized They will accept CCD cameras with fixed focal length or motorized zoom lenses The enclosures are wired for lenses with preset capabilities MODELS EH8104 4 inch diameter 17 inch length two 20 watt heaters EH8106 6 inch diameter 20 inch length two 40 watt heaters Installation MOUNTING The enclosure can be mounted to a wall mount ceiling pedestal mount or pan tilt mounted to a wall or ceiling For proper installation refer t
10. o the instructions supplied with the mount The enclosure should be attached to the mount or pan tilt by a minimum of two 1 4 20 fasteners not supplied CAMERA AND LENS INSTALLATION To install the camera and lens perform the following steps 1 Remove the rear plate of the enclosure Refer to Figure 1 and do the following a Remove the spiral retaining ring from the back of the enclosure Use a screwdriver to pry the end of the spiral retaining ring from the retaining ring groove b Pull on the T handle to remove the rear plate from the housing 2 Slide the sled out of the enclosure 3 Remove the desiccant bag from the camera sled Do not discard the bag 4 Mount the camera and lens onto the sled a Extend the lens to the maximum length before positioning the camera and lens b Position the camera and lens so that they do not extend beyond the track c Fasten the camera and lens to the sled Fastener is not supplied 5 Connect wiring for camera power lens functions and video Refer to Figure 2 6 Unwrap and install the desiccant bag inside the enclosure 7 Reinstall the camera sled by sliding it back into the enclosure body Secure with the spiral retaining ring 8 Pressurize the inside of the enclosure and assemble the mating connector Refer to the sections Recharging and Reassembly and Mating Connector Assembly 4 C1407M G 12 04 SPIRAL RETAINING SPRING RETAINING SPRING END
11. p the individual conductors back 1 4 inch 6 mm and thread them into the appropriate holes through the rubber grommet Refer to Figure 2 4 Solder the individual conductors to the appropriate pins in the back of the connector refer to Figure 2 Push the rubber grommet into the back of the connector BACK OF CONNECTOR 5 Screw the connector shell to the back of the connector and tighten Tighten the compression nut strain relief as far as possible to compress the sealing ring inside the shell Attach the cable clamps to the compression nut strain relief THREADED END COMPRESSION NUT AND STRAIN RELIEF CABLE CLAMP C1407M G 12 04 RECHARGING THE ENCLOSURE You may use your own charging equipment or Pelco s EH8000RKIT to recharge the enclosure If you are using your own equipment adjust the regulator for an output pressure of 12 psi 83 kPa If you are using the EH8000RKIT it uses a regulator with a fixed nonadjustable output pres sure of 12 psi 83 kPa The gauge reads the tank pressure only Refer to Figure 1 and do the following to pressurize the inside of the enclosure with nitrogen it 1 Open the tank valve of the charging 2 Remove the cap from the enclosure s Schraeder valve and then attach the air chuck from the charging equipment to the valve 3 To reduce the purge time necessary to remove air from the enclosure position the enclosure so that the window is pointing up 4 Remove the plas
12. rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are ins
13. tic cap on the pressure relief valve on the rear of the enclosure Use a small screwdriver and hold the valve open Allow the nitrogen to flow through the enclosure until the humidity indicator registers the lowest humidity level changing color from pink to blue The humidity indicator can be viewed through the front window of the enclosure looking at the inside top of the enclosure Once the humidity indicator registers the lowest level remove the screwdriver and allow nitrogen to continue to flow into the enclosure until you no longer hear the flow of nitrogen from the tank to the enclosure 5 Remove the charging equipment air chuck from the Schraeder valve Replace the Schraeder valve and pressure relief valve caps POWER CONNECTION 1 Connect ground wire to the ground stud on the back of the enclosure 2 Connect the mating connector to the rear of the enclosure Operation The heaters are thermostatically controlled to come on at 40 F 4 C and go off at 60 F 16 C Maintenance At a minimum the enclosure should be recharged once a year Also recharge the enclosure after opening for servicing See the Servicing section for instructions on how to disassemble reassemble and charge the enclosure ACCESSORIES EH25 81040RKIT O ring kit including desiccant bags for EH8104 EH80060RKIT O ring kit including desiccant bags for EH8106 EH8106L EH8000LUBE O ring lubrication kit for EH8100 Series EH8000RKIT Dry nitrogen rec
14. tructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C1407M 6 94 Original version C1407M A 5 96 Revised to incorporate which deals with the addition of the pressure sensor option kit and associated wiring update and ECO s 96 131 and 96 147 which deal with changes to heater kit configurations C1407M B 5 96 anual revised to new format Figure 6 revised to remove pressure sensor switch Refer to manual C1445M for switching wiring Figure 8 and Section 9 0 revised to include grounding lug 8 97 anual revised and renumbered to new format Section 2 2 added for CE and UL Compliance Revised Table B EH8100 Series Enclosure Mechanical Parts List to add EH810626SS Cradle Weld Assembly per ECO 97 047 6 98 Revised Section 3 4 and Figure 5 11 98 Editing changes Revised certifications Figure 8 Tables A and B and specifications Repaginated manual C1407M C 3 00 Revised connector assembly instructions Created separate manual for EH8100 Series Sun Shroud C422MC Moved exploded assembly diagram and parts lists to new maintenance service manual C1407SM Updated manual to new format C1407M
Download Pdf Manuals
Related Search