Pelco C3422M-B User's Manual
Contents
1. 12 C3422M B 3 08 Table G Switch Settings for SW1 Pelco P Protocol Control NOTE For Coaxitron controls SW1 is not used set all switches to the OFF position For Pelco D protocol control systems refer to Table H on page 13 SPECTRA SWITCH SETTING SPECTRA SWITCH SETTING ADDRESS swi 1 sw1 2 SW1 3 SW14 SW1 5 ADDRESS SW11 SW1 2 SW1 3 SW1 4 SW1 5 18 ON OFF OFF OFF ON 19 OFF 0 OFF OFF ON 20 ON 0 OFF OFF ON 21 OFF OFF ON OFF ON 22 ON OFF ON OFF ON 23 OFF 0 ON OFF ON ON ON ON OFF OFF 24 ON 0 ON OFF ON OFF OFF OFF 0 OFF 25 OFF OFF OFF ON ON 10 ON OFF OFF ON OFF 26 ON OFF OFF ON ON 11 OFF ON OFF 0 OFF 27 OFF 0 OFF ON ON 2 ON ON OFF ON OFF 28 ON 0 OFF ON ON 13 OFF OFF ON 0 OFF 29 OFF OFF ON ON ON 4 ON OFF ON ON OFF 30 ON OFF ON ON ON 15 OFF ON ON 0 OFF 31 OFF 0 ON ON ON 6 ON ON ON 0 OFF 32 ON 0 ON ON ON Table H Switch Settings for SW1 Pelco D Protocol Control NOTE For Coaxitron controls SW1 is not used set all switches to the OFFposition For Pelco P protocol control systems refer to Table G on page 13 SWITCH SETTING SWITCH SETTING ADDRESS SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 ADDRESS SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 1 ON OFF OFF OFF OFF OFF OFF OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 4 O2. Dome Drive Lower Dome ELECTRICAL Dome Drive Only Input Voltage 316L stainless steel Aluminum thermoplastic 316L stainless steel Polycarbonate 0 09 inch thick 316L stainless steel Brass Brass Nickel plated steel f 1 0 light loss Zero light loss Schrader 8 psig not factory pressurized 10 psig 360 continuous pan rotation 2 to 92 0 1 to 80 sec manual operation 150 sec turbo 0 1 to 40 sec manual operation 400 sec 200 sec Assumes no wind chill factor 140 F 60 C absolute maximum 122 F 50 C sustained maximum 60 F 51 1 C absolute minimum minimal icing at sustained minimum of 50 F 45 C prevents icing at sustained minimum of 40 F 40 C de ices 0 1 inch 2 5 mm within 3 hours after power up 10 2 Ib 4 60 kg 3 3 Ib 1 48 kg 3 3 Ib 1 48 kg 18 32 VAC 24 VAC nominal 22 27 VDC 24 VDC nominal For variable speed operation an appropriate controller is required With fixed speed controllers pan tilt speed is 20 sec The CM6700 CM6800 controller with the KBD200A keyboard has programmable fixed speeds C3422M B 3 08 Input Power 24 VAC 24 VDC Fuse Auxiliary Outputs Alarm Inputs 73 VA nominal with heater 3 A nominal with heater 1 25 A 2 7 29 5 10 6 26 7 ad NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES C3422M B 3 08 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY
3. Contact your local dealer for procedures for recycling this equipment eS REVISION HISTORY Manual Date Comments C3422M 9 06 Original version C3422M A 11 06 Inserted Spectra III compatibility note Added serial port settings to Table F C3422M B 3 08 Added information to Preinstallation section regarding the use of O ring lubricant to create an airtight seal Pelco the Pelco logo Camclosure Digital SENTRY Endura Esprit ExSite Genex Intelli M Legacy and Spectra are registered trademarks of Pelco Inc Spectra Ill is a trademark of Pelco Inc DLP is a registered trademark of Texas Instruments Incorporated Vicon is a trademark of Vicon Industries Inc Copyright 2008 Pelco Inc All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1S09001 Australia Finland France Germany Italy Macau The Netherlands Russia Singapore South Africa Spain Sweden United Arab Emirates United Kingdom United States
4. OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON ON ON ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF ON OFF ON OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON OFF OFF OFF ON OFF OFF ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF ON OFF OFF ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OF
5. ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON 0 OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON 0 ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON N FF 0 ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF N ON FF 0 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 1 90 O
6. Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on fiber optic products and TW3000 Series unshielded twisted pair UTP transmission products Three years on Spectra IV products Three years on Genex Series products multiplexers server and keyboard Three years on DX Series digital video recorders DVR5100 Series digital video recorders DigitalSENTRY Series hardware products DVX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products Three years on Camclosure and Pelco branded fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Three years on PMCL200 300 400 Series LCD monitors Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra III Spectra Mini Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 9
7. OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF 91 92 193 94 195 96 197 98 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 C3422M B 3 08 16 Specifications GENERAL Construction Back Box Dome Drive Lower Dome Trim Ring Bubble V B and Pressure Relief Schrader Valve Connector Light Attenuation Smoked Clear Pressurization Valve Pressure Pressure Relief Pan M Ve ovement ical Tilt Manual Pan Tilt Speeds Pan Tilt Preset Pan Tilt Opera Speeds ing Temperature Maximum Minimum Weigh Bac t approximate k Box
8. band 4 Prepare the lower dome for installation a Remove the O ring from the lower dome b Lightly apply O ring lubricant supplied to the O ring c Reinstall the O ring in the groove on the trim ring NOTES e Repeated assembly of the unit without exercising extreme caution to protect the integrity of the O ring and sealing surfaces will result in increased refilling cycles Plan carefully to minimize service accesses e Use the supplied O ring lubricant to ensure an airtight seal when installing the lower dome Figure 4 Applying O Ring Lubricant 5 Attach the back box leash to the lower dome and let the lower dome hang to the other side of the back box C3422M B 3 08 Figure 5 Attaching the Back Box Leash 6 Install the dome drive Refer to Table A for a list of compatible dome drives and back boxes a Set the DIP switches located on the base of the dome drive Refer to the labels located on the base of the dome drive or to Switch Settings on page 12 Line up the blue and red tabs with the blue and red arrows on the hinged door inside the backbox Push in the tabs Insert one side and then the other side Continue pushing until both sides of the dome drive click into place Figure 6 Installing the Dome Drive C3422M B 3 08 Table A Spectra Dome Drive and Back Box Compatibility Back Box Dome Drive Spectra Il Spectra lll Spectra IV Spectra IIP Spectra III Spectra
9. 0 days The air filter is not covered under warranty Two years on Intelli M elDC controllers One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty
10. F OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF 31 32 33 34 35 36 37 38 39 40 42 43 44 45 46 47 48 49 50 51 41 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 C3422M B 3 08 14 SWITCH SETTING SWITCH SETTING ADDRESS swi 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 9 a a 7 a wo J pu a 9 j a 7 sr 7 D ep s a N po a _ a A a Ed ez a lt ON ON ON ON ON ON ON ON
11. FF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON 0 ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF F FF 0 OFF ON FF 0 N OFF OFF OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON OFF ON OFF OFF OFF ON FF 0 113 115 117 119 20 121 22 123 24 125 26 127 28 129 30 131 32 133 34 135 36 137 38 139 40 141 42 143 44 145 46 147 48 149 50 15 C3422M B 3 08 SW
12. FF OFF ON OFF OFF OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 22 OFF ON ON OFF ON OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 9 ON OFF OFF ON OFF OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 11 ON ON OFF ON OFF OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 27 ON ON OFF ON ON OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 30 OFF ON ON ON ON OFF OFF OFF C3422M B 3 08 13 SWITCH SETTING SWITCH SETTING ADDRESS SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 op a 7 my a o J a a Ww j ak 7 sr 7 as a ep we a N ee 7 7 a A a LU ez a x OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF
13. INSTALLATION Pressurized Spectra IV Series Pendant Back Box with Fiber Optic Option C3422M B 3 08 Preinstallation NOTE This manual is designed to be a reference tool for the installation of your system For best results and ease of installation the dome system should be assembled pressurized and tested before installation A Pressurized Spectra IV cable harness supplied with the back box is required to test and monitor the pressurized dome 1 Install the fiber optic module Open the hinged door to the back box by pushing the tab lock towards the wall of the unit and lifting the door open Remove the plug from the 16 pin connector Install the module in the 16 pin connector Secure the module to the circuit board standoff using the screw and lock washer provided 16 PIN CONNECTOR Figure 1 Installing the Fiber Optic Module 2 Connect the back box fiber optic connector to the mating connector on the module Be sure to route the fiber optic cables between the plastic housing and the outer wall of the back box before attaching the two connectors Follow all applicable instructions provided by the manufacturer of the fiber optic module NOTE All bends in the fiber optic cable must be 1 inch diameter or greater Figure 2 Connecting the Back Box Fiber Optic Connector 2 C3422M B 3 08 3 Loosen the V band attached to the back box and let it hang to the side Figure 3 Loosening the V
14. ITCH SETTING SWITCH SETTING ADDRESS swi 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 my a 7 a wo J a x j ai 7 sr 7 D a a N lt 7 7 oi a A a LU ez a a lt ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF OFF ON ON ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 OFF ON OFF OFF
15. IV e e 7 Install the lower dome a Position the lower dome so that the blower duct inside the back box is between the studs attached to the inside of the lower dome b Install the V band around the lower dome and then tighten the fastener of the V band c Test the operation of the unit before pressurizing the dome Figure 7 Installing the Lower Dome 8 Pressurize the inside of the dome with nitrogen a Remove the cap from the Schrader valve of the dome Place the air chuck from the charging kit over the Schrader valve NOTE You may use your own charging equipment or Pelco s EH8000RKIT recharge kit If you are using your own equipment adjust the regulator for an output pressure of 12 psi 83 kPa b Open the tank valve of the charging kit Fill the dome with nitrogen for a minimum of five minutes to replace the oxygen inside the dome with nitrogen c Remove the air chuck and then replace the Schrader valve cap C3422M B 3 08 5 d Refer to the Operation Programming manual C3412M for instructions on how to view the current readings for temperature and pressure Record the initial temperature and pressure readings of the dome in the space provided below Initial Temperature Initial Pressure NOTES e Record the initial temperature and pressure readings for future reference It is normal for changes in temperature to cause dome pressure to rise and fall e You must perform an annual r
16. N White Auxilary 2 Cat5 Cable P Green TX R White Green TX S Blue RX T White Blue RX U Orange UTP Video V White Orange UTP Video W Brown Spare X White Brown Spare Coaxial Cable Y Coaxial Core Video Out Z Coaxial Shield Video Shield Individual Wires a White 24 VAC AC HI b Black 24 VAC AC LO Green Yellow Earth Ground Switch Settings WARNING If you are using Pelco D or Pelco P protocol control your system may not operate if the baud rate and address switches are not set correctly The switches are set at the factory at the defaults for Pelco D protocol control 2400 baud and address 1 Table F Switch Settings for SW2 Special Systems Switch Number 1 2 3 4 5 6 7 8 9 10 AD 32 Preset System ON CM9502 Setting ON Vicon Not currently available SW2 3 is reserved for future use Serial Port Settings Switch Number 1 2 3 4 5 6 7 8 9 10 RS422 OFF OFF RS485 4 Wire OFF ON RS485 2 Wire ON ON Pelco D and Pelco P Protocol Baud Rate Switch Number 1 2 3 4 5 6 7 8 9 10 2400 Baud Default for Pelco D Protocol Control OFF OFF OFF 4800 Baud Default for Pelco P Protocol Control ON OFF OFF 9600 Baud OFF ON OFF Video Cable Type Switch Number 1 2 3 4 5 6 7 8 9 10 Coax Cable OFF UTP Cable ON Dome Termination Switch Number 1 2 3 4 5 6 7 8 9 10 Terminated ON Not Terminated OFF
17. efill to be consistent with the intent of the application Figure 8 Pressurizing the Dome C3422M B 3 08 Site Installation 1 Feed a fiber optic cable not supplied and the supplied wiring harness into the front of the mount and out the back of the mount Connect the wires as required Refer to Table B Table C and Table D on page 10 and Table E on page 11 for cable and wiring information Fasten the mount to the mounting surface refer to the instructions supplied with the mount Figure 9 Wiring the Mount 2 Remove the back box mounting plate Loosen the nuts on top of the back box until they reach the locking material at the end of the studs and then turn the mounting plate clockwise and lift C3422M B 3 08 Figure 10 Removing the Back Box Mounting Plate 3 Thread the wiring from the mount through the mounting plate and then attach the mounting plate to the mount If outdoors apply thread compound supplied to the threads on the mounting plate Figure 11 Attaching the Mounting Plate 4 Attach the wire harness connector to the mating connector located on the top of the back box Connect the fiber optic cable Insert the studs and nuts on top of the back box into the mounting plate turn the back box counterclockwise and then tighten the three nuts C3422M B 3 08 Figure 12 Attaching the Wire Harness Connector C3422M B 3 08 Table B Fiber Optic Cable Types Spectra Model Cable Type Co
18. nnector Single mode PRS models 9 125 um cable ST type Multimode PRM models 62 5 125 hm cable ST type Table C 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices Wire Gauge Total VA 20 AWG 18 AWG 16 AWG 14 AWG 0 5 mm 1 0 mm 1 5 mm 2 5 mm 73 39 ft 62 ft 98 ft 156 ft 12 m 19 m 30 m 48 m NOTES e Input power for the dome is 24 VAC only Power consumption is 73 VA per dome e Use a 24 VAC transformer with a minimum of 100 VA Table D UTP Wiring Distances Receiver Maximum Distance Active 0 to 3 000 ft video only 0 to 914 4 m Passive 0 to 750 ft video Coaxitron and 0 to 228 6 m Pelco V Sync NOTE As a minimum UTP requires Cat5 100 ohm twisted pair cable 10 C3422M B 3 08 C3422M B 3 08 Table E Configuration of Wire Harness Pin Wire Color Function 9 Conductor Cable A Black Alarm 1 B Red Alarm 2 C White Alarm 3 D Green Alarm 4 E Brown Alarm 5 F Orange Alarm 6 G Yellow Alarm 7 H Violet Ground Blue Not Used 5 Conductor Cable J Black Relay N O Aux 1 K Red Relay N C Aux 1 L Green Relay Common Aux 1 M Brown Ground
19. repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number sales order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which he item was received by Pelco RETURNS o expedite parts returned for repair or credit please call Pelco at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair and designated return location All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Green The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE
Download Pdf Manuals
Related Search