Pelco SS3002 User's Manual
Contents
1. Cable distances should not exceed the distances specified in Section 3 1 The fol lowing are some recommended common installation practices 1 Always use jacketed stranded multi conductor interconnecting cable between the control and the pan tilt with additional conductors than needed for future servicing and or additions 2 Always use color coded conductors for ease of wiring and to identify functions at a later date 3 Keep a wiring diagram with the system for later use and reference INPUT CONNECTOR ENS VIDEO SHIELD YEL CAMERA WHITE J2 CONNECTOR CAPACITOR 15 MFD 100V CAPUO015 0 100N IRIS BLACK PAN MOTOR 2508001 TILT MOTOR PS78001 FOCUS W BRN CONNECTOR CONMAB6100 ZOOM W RED CONNECTOR PINS CON66102 7 LENS COMM W ORG SWITCH SWI1SM1 INPUT CONNECTOR CON206044 1 SEDESRND 9 GRAN MATING CONNECTOR ASSY CONA14S ACTUATOR SWIJS138B LENS MATING CONNECTOR CONMAS6100 Figure 1 PT280 24P Wiring Schematic 6 PELCO Manual C428M B 2 98 3 3 CONNECTOR ASSEMBLY Installation and or testing will require you to assemble the connector parts pro vided Fabricate the interconnecting cable according to the following steps refer ence Figure 2 1 Slide part A of the cable clamp item 1 over the end of the cable item 1 part C with the threaded end of the cable clamp facing the connector item 5 2 Ifthe cable has a diameter less than 1 2 inch 1 3 cm slide the rubber boot item 2 over the end of the ca2. Pan Tilt Lens Cam AC PT280 24P PT280 24SL 54 grnd 4 2 PT280 24P PP 94 grnd 8 2 PT280 24SL PP 10 grnd 8 2 Camera power lens functions and video are fed through the input connector on the base of the pan tilt The following are the cable requirements for the PT280 series pan and tilts 5 Conductor 6 Conductor 20 Awg 110 ft 33 53m 210 ft 64 01m 18 Awg 180 ft 54 86m 330 ft 100 58m 16 Awg 290 ft 88 39m 530 ft 161 54m Using 2 wire common 3 2 WIRING INSTRUCTIONS NOTE f you are not using the C1906 C1906 PP C1925 or C1925 PP pretested cable you must reverse the left right and up down function pins as shown in Figure 1 PELCO Manual C428M B 2 98 To install and test the pan tilt you will need to assemble the connector parts pro vided Refer to Section 3 3 for connector assembly The PT280 series pan tilts are prewired for all control functions pan tilt motorized zoom lens 24 VAC camera power and video All connections are made at the input connector eliminating the need for wiring harnesses made in the field When using Coaxitron Control Systems consider using the C1906 C1906 PP C1925 or C1925 PP factory assembled pretested cables which are wired for inverted applications Wire the control cable per the wiring diagram provided in the PT280 Series Pan Tilt manual C324M for the specific pan tilt you are using The PT280 24P basic pan tilt wiring diagram is included in this manual for reference only
3. PELCO SS30 SS3000 SS3002 Dome Enclosures Installation Operation Manual C428M B 2 98 LISTED Pelco 300 W Pontiac Way Clovis e CA 93612 5699 USA Pelco Online 9 http www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 DataFAX 1 559 292 0435 CONTENTS Section Page 1 0 GENERAL ix RO et ER ieee ds 3 1 1 IMPORTANT SAFEGUARDS AND WARNINGS 3 2 0 3 0 INSTALLATION eter etre nea nein 3 1 CONDUCTOR AND CABLE REQUIREMENTS 3 2 WIRING INSTRUCTIONS sss p 3 8 CONNECTOR ASSEMBLY sse 3 4 MOUNTIN iens rre it rtr ett er Rer eese T oan n 3 4 1 Ceiling Wall Mounting 3 5 ADJUSTMENTS reete eco re eue nto rena eaae ee eR Ne ERR eaa 4 0 MAINTENANGE retten erre eiae ht ne nr ean in tens 12 5 0 MECHANICAL PARTS LIST 125 2 98779 CH RENE ORO IRR LU cad 13 6 0 SPECIFICATIONS sss e nennen nnne 14 7 0 WARRANTY AND RETURN INFORMATION senes 16 LIST OF ILLUSTRATIONS Figure Page 1 PT280 24P Wiring Schematic sss 6 2 Connector Assembly uu 3 Mounting Configurations 8 4 Locking the Pipe Nut 4 eee 9 5 SS3000 Exploded Assembly Diagram sese 10 6 PT280 24P Limit Locations 7 S30
4. preset scan tour and auto scan modes Pelco will warranty all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss result ing from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there i
5. SS3000 Dimension Drawing sse 15 LIST OF TABLES Table Page A SS3000 Exploded Assembly Diagram Corresponds to Figure 5 13 B Parts for SS30 Fixed Mount Dome Only Not Shown in Figure 5 13 REVISION HISTORY Manual Date Comments C428M C428M C428M B 3 87 5 90 Original version Rev A Revised Section 4 3 Connector Assembly procedures Section 4 5 Adjustments for addition of fixed limit stop and Section 6 0 Mechanical Part List Figure 1 parts listed revised 6 95 Rev B Revised Section 4 1 Conductor amp Cable Requirements cable requirements and distances Section 4 4 1 Ceiling Wall Mounting instructions for Schneider ring and Section 6 0 Mechanical Parts List updated parts Figure 1 revised to show safety ground wire as green Revised Section 6 0 Mechanical Parts List regarding part numbers for lower domes Added item 14 Revised Section 4 0 Maintenance Changed manual to new format 8 96 2 98 PELCO Manual C428M B 2 98 1 0 GENERAL 1 1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not
6. adjust the pan tilt limits perform the following steps Refer to Figure 6 for limit tempt to adjust limit stops stop locations when pan tilt is in opera tion Damage to the equip 1 Factory pan limits are set to 0 355 and tilt limits at 45 Pan to the right using ment can result Also do the joystick control until the desired RIGHT pan limit is reached not operate equipment Joc 2 Adjust the pan limit stop until the actuator clicks Lock the limit into position without limit stops Do not P p p remove or reposition fixed 3 Pan to the desired left position adjust the pan limit stop until the actuator limit stop on the PT280 clicks and lock into position 24P pan tilt DAMAGE WILL OCCUR 4 Pan to the left and right to verify exact positioning and tighten both stops se curely 5 Remove the left cover plate by removing the two screws for access to the tilt limit stops 6 Loosen the screws and move the DOWN limit stop to the furthest position Using the joystick control tilt the unit to the desired down position 7 Move the DOWN limit stop until the actuator clicks Lock the limit into position 8 Adjust the UP limit stop in the same way 9 Tiltup and down to verify exact positioning and tighten both stops securely TILT DOWN LIMIT STOP TILT UP LIMIT STOP PAN LIMIT SWITCH ACTUATOR PAN RIGHT LIMIT STOP PAN LEFT FIXED LIMIT STOP LIMIT STOP Figure 6 PT280 24P Limit Locations PELCO Manual C428M
7. consideration when wiring the unit as the motions will be reversed NOTE The small hole in the upper dome for safety chain attachment should be positioned at the back con nector end of the camera PELCO Manual C428M B 2 98 1 Select an appropriate length of 1 1 2 NPT pipe for the mount you have se lected Once the mount is installed insert and tighten the pipe to approxi mately 30 ft Ib then tighten the 8 32 screw in the pipe nut to lock the pipe threads Slide the black 10 OD Schneider ring over the pipe and then slide the upper dome onto the pipe and lock it out of the way with a suitable retainer Screw the mounting flange item 4 Figure 5 onto the pipe and tighten to approximately 20 ft Ib Tighten the 8 32 screw in the pipe nut to lock the pipe threads refer to Figure 4 Align the three hole pattern in the pan spindle PT280 24P with the holes in the lower bracket item 5 Figure 5 and attach with 1 4 20 x 5 8 hex head bolts and lock washers provided Tighten firmly Assemble the lower bracket and pan tilt to the mounting flange item 4 Figure 5 using 1 4 x 5 8 hex head bolts flat washers and hex nuts provided Attach the upper drive bracket item 3 to the bottom spindle side of the pan tilt using four 4 10 32 x 1 2 pan head screws and lock washers pro vided Refer to Figure 5 for proper orientation Feed the main cable from the control or receiver through the center of the 1 1 2 pipe and
8. Assembly PELCO Manual C428M B 2 98 7 3 4 MOUNTING The SS3000 enclosure is designed to be suspended from a suitable length of 1 1 2 pipe threaded at both ends This pipe can be interfaced to either a Pelco MRWA wall adapter MRCA ceiling adapter or coupled to a longer length of pipe see Figure 3 CEILING MOUNT STRUCTURAL CEILING MOUNTING CEILING MOUNT TEE UNION p DROP CEILING MOUNTING WALL MOUNTING Figure 3 Mounting Configurations 8 PELCO Manual C428M B 2 98 3 4 1 Ceiling Wall Mounting NOTE The Schneider ring referred to in these instructions is a 10 inch black aluminum ring designed to fit around the square portion of the up per dome Use of this ring helps to camouflage movement of the dome NOTE Disregard step 3 if using the PT280 24SL pan tilt NOTE When installing a PT280 24SL pan tilt with the slip ring option you will need to remove one 1 of the 1 4 20 fasteners holding the mount ing flange to the SL2800 bracket Pivot the pan tilt assembly to one side to allow the connector and cable to pass through After the connection is made pull the connector back up into the pipe and reattach the mounting flange NOTE When mounting a long cam era lens assembly 13 to 15 intoa SS3000 enclosure it must be mounted to the pan tilt backwards so the lens is to the rear of the pan tilt This is to allow full downward tilt of the long lens This must also be taken into
9. B 2 98 11 4 0 MAINTENANCE 12 Clean the acrylic lower dome as necessary to maintain a clear picture Be careful not to scratch the surfaces of the dome Exterior Surface Clean the dome s exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic plastic Either liquid or spray cleaner wax suitable for fine furniture is acceptable Interior Surface Except Chrome Clean the same as the exterior surface Interior Surface Chrome The inside surface of a chrome dome is easily scratched Use the following precautions to maintain the dome s surface a b Always handle the dome from the outside of its circular flange Never touch the coated inside surface The acid in your fingerprints will even tually etch the coating if the fingerprints are not carefully removed according to the recommended cleaning procedure in item e If dust or other contaminants accumulate on the dome s interior remove the debris with compressed air Compressed air cans are available from photo graphic equipment or electronic supply dealers If heavy residue accumulates and cannot be removed with air pressure rinse with water and immediately dry with air pressure so that water spots will not remain Avoid wiping the coated surface with direct hand pressure it will eas ily abrade unless extreme care is taken Once scratched the dome cannot be recoated If internal wiping is necessary avoid han
10. ERAL Construction Upper dome Black U L 94HB rated ABS plastic Lower dome Acrylic hemisphere with distortion free viewing window with light attenuation factor of 1 f stop SS30 SS3000 or mirrored lower dome with 2 f stop SS3002 Rotates with pan and tilt camera and lens Environment Indoor 32 to 120 F 0 to 48 89 C Unit Weight 6 Ib 2 72 kg approximate Dimensions See Figure 7 Design and product specifications subject to change without notice 20 00 50 80 24 00 60 96 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 7 SS30 SS3000 Dimension Drawing PELCO Manual C428M B 2 98 15 7 0 WARRANTY AND RETURN INFORMATION Pelco and the Pelco logo are registered trademarks of Pelco Copyright 1998 Pelco All rights reserved 16 WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Excep tions to this warranty are as noted below Two years on all standard motorized and fixed focal length lenses e Two years on Legacy Intercept PV1000 Series CM6700 CM8500 CM9500 CM9750 CM9760 Matrix Spectra DF5 Series and DF8 Fixed Dome products Two years on WW5700 series window wiper excluding wiper blades e Two years on cameras Six months on all pan and tilts scanners or preset lenses used in continuous motion applications e g
11. be installed where exposed to rain and moisture 3 Only use replacement parts recommended by Pelco 4 After replacement repair of this unit s electrical components conduct a resis tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry 5 The installation method and materials should be capable of supporting four times the weight of the enclosure pan tilt camera and lens combination The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit maintenance instructions in the literature accompanying this i This symbol indicates that there are important operating and unit CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please thoroughly familiarize yourself with the information in this manual prior to installation and operation PELCO Manual C428M B 2 98 3 2 0 DESCRIPTION Pelco s SS30 SS3000 series is a full sphere discreet surveillance enclosure de signed to be suspended from a ceiling and to complement the interior decor of businesses hotels and offices The smoked finished lower dome effectively camouflages a CTTV security surveillance system without compromising the quali
12. ble and pull through the cable clamp to so that the boot encases the cable and forms a good seal 3 Strip back the cable jacket approximately 1 1 4 inches 3 2 cm and separate the individual conductors item 3 4 The contact pins supplied with the mating connector are the crimp type which may also be soldered if you so desired item 4 5 After crimping or soldering the contact pins to the conductors push them into the proper holes in the connector until they snap in place 6 Slide part A of the cable clamp toward the connector and screw the parts NOTE Contacts cannot be removed together Attach part B item 1 onto part A and connect both parts with the from the connector without the use screws provided of the appropriate AMP extraction tool 7 Connect the cable assembly to the unit and seat the connector by twisting the which is available from Pelco locking collar until it snaps into position threaded end of cable clamp y STRIP 1 8 R STEPS 3 7 Y N CRIMP INSULATION OUTSIDE JACKET OF CABLE ITEM 5 DETAIL 37 X X FRONT VIEW FRONT VIEW 37 PIN CONNECTOR 28 PIN CONNECTOR 26 FRONT VIEW 16 PIN CONNECTOR THE MOST COMMONLY USED CONNECTOR PIN OUT CONFIG URATIONS ARE SHOWN HERE REFERENCE THE CONNECTOR mE DRAWING APPLICABLE TO aan 12 3 YOUR SITUATION FRONT VIEW FRONT VIEW 14 PIN CONNECTOR 9 PIN CONNECTOR Figure 2 Connector
13. connect it to the cable of the pan tilt Pull the cable and con nector back up into the pipe so that it does not get caught on the rotating parts Install the camera lens assembly onto the tilt table of the pan tilt Connect the proper cables camera lens function Remove the retainers from the upper dome and lower it until it seats itself on the upper drive bracket 1 1 2 NPT PIPE PIPE NUT Figure 4 Locking the Pipe Nut CAUTION The lower dome will shatter if dropped Always operate with the safety chain at tached Do not rotate pan tilt by hand Rotate by con troller only NOTE The Schneider ring is not shown in this diagram It is de signed to fit over the square por tion of the upper dome item 1 PT280 24SL 10 11 Turn the system on and rotate the pan tilt Check for cable interference Tilt the camera up and down and check for clearance of all moving parts After all tests have been done and the system is functioning properly attach the safety chain to the upper dome with the fasteners provided Install the lower dome being careful to align the viewing window Check for sufficient clearance between the lens and the lower dome MOUNTING COLUMN 6 UPPER DOME 1 UPPER BRACKET 3 MOUNTING BRACKET 4 LOWER BRACKET 5 pe CHAIN 10 LOWER DOME 2 Figure 5 SS3000 Exploded Assembly Diagram 10 PELCO Manual C428M B 2 98 3 5 ADJ USTMENTS CAUTION Do not at To
14. d rubbing Instead make a wick as follows Use a very soft paper towel Roll a section into a tightly wound tube Tear the tube in half and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with water Hold the dome with its opening facing downward and wipe the interior of the dome with the wet end of the wick Use a circular motion starting from the outside and spiraling into the center Use a new wick for each two passes over the dome PELCO Manual C428M B 2 98 5 0 MECHANICAL PARTS LIST Table A SS3000 Exploded Assembly Diagram Corresponds to Figure 5 Dome upper Dome lower smoked SS30 SS3000 Dome lower chrome SS3002 Bracket upper drive SS3000 SS3002 Bracket mounting hanging weld assy Bracket lower SS3000 SS3002 Pipe mounting Not used Not used Velcro black 5 8 wide x inch not shown Chain 16 single jack x 6 length Trim edge black chrome not shown Snap body for chain assembly not shown Ring Schneider 10 OD x 9 812 ID not shown Velcro black 5 8 wide x inch not shown S300010000 S300010001 S331100 SS30004000COMP S300031001WA PM200C4000COMP SS34002COMP TV10002 SB2511000 S300010004 SB2511001 S30004100COMP TV10003 Part number is for the dome only To order a complete lower dome assembly specify the part numbers SS30004003COMP smoked and SS334200COMP chrome These part numbers include item
15. s 2 10 12 and 14 Table B Parts for SS30 Fixed Mount Dome Only Not Shown in Figure 5 PELCO Manual C428M B 2 98 Tilt table fixed black Pedestal spacer black Dome support bracket Fixed bracket black Pedestal mount fixed CM14004100BCOMP CM30004001 COMP CM30024000COMP EM14004001BCOMP PM74000COMP 13 6 0 SPECIFICATIONS 14 ELECTRICAL Input voltage Power Requirements Pan Tilt Connectors Pan Tilt Lens Video Camera Power Motors Limit Switches Conductor Requirements MECHANICAL 24 VAC required for pan tilt Starting 47 amp 11 2 vA 56 amp 13 5 vA Running 31 amp 7 5 vA 38 amp 9 2 vA AMP CPC type mate supplied Hirschmann MAB6100 BNC Spade lugs Two phase induction type instantaneous reversing 5 amp external adjustment See Section 3 1 for detailed specifications refer to PT280 series product manual C324M Pan Pan Speed Tilt Tilt Speed Max Load Dome Drive Max Camera and Lens Length Movement in horizontal plane PT280 24P 0 355 PT280 24SL 0 360 12 sec 1 no load condition 90 movement in vertical plane 3 sec 5 no load condition 15 Ib 6 81 kg at 5 from tilt table surface to center of gravity Lower dome mounts into upper dome with Velcro fasteners complete assembly is driven by pan tilt 16 0 inches 40 6 cm including BNC connector PELCO Manual C428M B 2 98 GEN
16. s a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Ship freight prepaid to Pelco 300 West Pontiac Way Clovis CA 93612 5699 Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RAnumber if returned for repair Goods returned for repair or credit should be clearly identified with the assigned CA RA number and freight should be prepaid All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Ship freight prepaid to Pelco 300 West Pontiac Way Clovis CA 93612 5699 PELCO Manual C428M B 2 98
17. ty of the video picture An op tional mirrored lower dome SS3002 is available The SS3000 Series has been engineered for ease of installation serviceability and relocation The lower dome quickly and easily detaches from the upper dome for convenient access to the camera and pan tilt 2 1 MODELS SS30 Full sphere enclosure with black opaque lower dome with smoked viewing window and fixed camera mount S3000 Full sphere enclosure supplied with a black opaque lower dome with smoked viewing window Fixed camera mount not supplied This dome is designed for use with an optional pan tilt assembly PT280 series S3002 Same as SS3000 except supplied with mirrored lower dome with 2 f stop light loss 2 2 OPTIONS PT280 24P Light duty indoor pan tilt 24 VAC PT280 24P PP Same as PT280 24P except has preset position PP option PT280 24SL Light duty indoor pan tilt with continuous 360 operation PT280 24SL PP Same as PT280 24SL except has preset position PP option MRWA Wall mount adapter MRCA Ceiling mount adapter 4 PELCO Manual C428M B 2 98 3 0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned for credit or repair 3 1 CONDUCTOR AND CABLE REQUIREMENTS Before installing the pan and tilt determine the conductor requirements and length of cable you will need to run based on the following Conductor requirements for the pan and tilt are as listed below plus coax cable
Download Pdf Manuals
Related Search