Pelco CM9760-KBD-E35 User's Manual
Contents
1. 559 348 1120 www pelco com INSTALLATION To change the U3 PROM chip on the KBD motherboard 1 Log off of the keyboard and then unplug it note which port you unplugged it from if you plug the cable back into the wrong port after the procedure your screen will be blank and you might draw the wrong conclusion as to the reason why Turn the keyboard over on its back and remove the 9 phillips screws that attach the bottom plate Refer to Figure 1 pay attention to the text references in the figure NOTE The screw towards the middle of the keyboard has a plastic retaining nut on some models This screw must be removed LAST it is referenced as screw 9 in Figure 1 Remove all other screws FIRST then lift the back cover off slightly reach in carefully to locate and hold the nut in place with your finger to keep it from turning and remove the last screw CAUTION After the last screw is removed lift off the bottom plate of the keyboard CAREFULLY and GENTLY in the direction indicated in Figure 2 Of the several wires that have their destination in the boot cover for the joystick are several fine wires that are soldered to the surface of the motherboard Rough handling could cause a wire to detach inadvertently Remove the 9 screws as indicated Remove the ninth screw last because in some models the screw is retained by 9 a plastic nut on the inside cover Follow the applicable step in the installation instructions After logging2. item was received by Pelco RETURNS n order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned or credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Copyright 1999 Pelco All rights reserved
3. off disconnect unit from system by removing cable Figure 1 Removing the CM9760 KBD Bottom Cover Remove the existing U3 PROM chip refer to Figure 2 from its socket using the provided extraction tool Work the chip out slowly to avoid damaging the socket 4 Remove the replacement PROM from the electrostatic bag and inspect it to confirm that the pins are straight 5 Orient the chip using the alignment notch as a guide refer to Figure 2 inset Verify pin to socket alignment and carefully press the chip into its socket until completely seated 6 This completes the installation Replace the cover Plug the cable detached in step 1 back into the same port CIRCUIT BOARD folic U2 U5 Be wary of pulling the bottom cover off too quickly These smaller wires soldered to the surface of the board could be easily detached Notched end of PROM Orient the notched end of the PROM with the notch on the alignment mask that exists on the surface of the board as shown Alignment mask notch Figure 2 Replacing the U3 PROM Chip PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Se
4. MGR version 7 50 000 v Date format entry changed from day month year to month day year vy Preset delete option moved to the Define Preset Menu y Parity byte selection for Coms 1 3 can be changed to none even or odd Button Key Functions Added v MAC Group X v ALT BWD Functions Added Y Options to define PIN in direct control mode Y GPI selection range extended Follow the INSTALLATION instructions starting on page 2 The chip provided in this package is for downgrading new KBD orders to allow them to be used with version 9760MGR 1 16 010 or earlier version of software With this kit the user can add new keyboards to an existing system version 1 16 010 or earlier 9760MGR software without having to upgrade to the latest system and 9760MGR software Of course the feature set available for the keyboard will correspond to that associated with the 1 16 010 version of 9760MGR software The installation of this chip enables the following v The feature set of button key define functions is commensurate with 9760MGR version 1 16 010 or earlier software vy Eliminates problems arising out of conflicts between new 9760KBDs using version 7 5 firmware with 9760MGR version 1 16 010 software Follow the INSTALLATION instructions starting on page 2 PELCO a 3500 Pelco Way Clovis e CA 93612 5699 USA In North America amp Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 e FAX 1
5. SYSTEM 9760 KBD FIRMWARE INSTALLATION INSTRUCTIONS C1500M 9 99 IMPORTANT SAFEGUARDS AND WARNINGS IMPORTANT Performing the System 9760 KBD upgrade does not erase user programmed information in existing keyboards CAUTION Only qualified personnel observing Electrostatic Discharge ESD precautions should perform the procedures described in this document Always wear a grounding strap connected to an approved grounding source when working on or around exposed electronic components Handle circuit boards by their edges DESCRIPTION OF CHANGES The instructions in this manual cover the installation of the following items CM9760 KBD E75 System 9760 KBD Software Upgrade Instructions Package contents 1 System 9760 KBD software U3 PROM chip version 7 50 p n 1C53 0043 2750 1 Chip Extraction Tool Not included but needed 1 Phillips screwdriver OR CM9760 KBD E35 System 9760 KBD Firmware Downgrade Kit Package contents 1 System 9760 KBD software U3 PROM chip version 3 50 p n 1C53 0006 2305 1 Chip Extraction Tool Not included but needed 1 Phillips screwdriver The chip provided in this package is for upgrading KBDs that have version 3 11 or earlier software To enable the full feature set embodied in this package the MGR and system software should be at the corresponding version level 7 50 000 The expanded feature set includes Feature Set vy Feature set of button key define functions commensurate with 9760
6. mages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state Pelco the Pelco logo Camclosure Esprit Genex Legacy System 9760 and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco lf a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned ethod of return shipment shall be the same or equal to the method by which the
7. ries fiber optic products hree years on Genex Series products multiplexers server and keyboard hree years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty wo years on standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series ixed dome products wo years on Spectra Esprit ExSite and continuous motion applications PS20 scanners including when used in wo years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for da
Download Pdf Manuals
Related Search