Pelco C1992M-A User's Manual
Contents
1. THE INTERIOR OF THIS UNIT THIS ACTION MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE Refer all servicing to qualified service personnel REMOVAL OF BACK COVER BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS Unplug the unit immediately and notify the service technician If liquid has been spilled into the display or the display has been exposed to rain or water If the unit has been dropped or the cabinet damaged If fuses continue to blow If the power cord is damaged or frayed If a distinct change from normal operation is apparent moomr When replacement parts are required be sure that the service technician uses components specified by the manufacturer which have the same characteristics as the original parts UNAUTHORIZED SUBSTI TUTIONS MAY RESULT IN FIRE ELECTRICAL SHOCK OR OTHER HAZARDS Upon completion of any service or repairs ask the technician to perform safety checks to determine that the equipment is in safe operating condition WARNING SERIOUS SHOCK HAZARDS EXIST WHIN THE COVERS OF THIS MONITOR DO NO 7 OPEN THE COVERS UNDER ANY CIRCUMS TANCES THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE 2 Pelco Manual C1992M A 12 03 DESCRIPTION The PMC10A is high resolution 10 inch 25 4 cm color monitor The unit has a resolution of 350 TV lines producing an excellent quality picture The monitor s power input of2. Wait 30 seconds for the picture tube to warm up and the power LED indicator to light 3 If required adjust the picture using the control knobs on the front panel Front Panel Adjustments TINT Color phase adjustment Turn clockwise to increase the greenish tones in the picture Turn counterclockwise to increase the reddish tones in the picture COLOR Color saturation level Turn the control knob clockwise to increase the saturation level and counterclockwise to decrease the saturation level CONT Contrast adjustment Proper adjustment will allow maximum gradations between the darkest and lightest picture contrast Turn the control clockwise to increase picture contrast and counterclockwise to decrease contrast BRIGHT Brightness display adjustment Turn the control clockwise to increase brightness and counterclockwise to decrease brightness SHARP Sharpness adjustment Adjust control knob to obtain the clearest picture VOLUME Audio adjustment Turn the control clockwise to increase volume and counterclockwise to decrease volume Table A Video Coaxial Cable Requirements RG59 U T50 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum cable requirements 75 ohms impedance All copper center conductor All copper braided shield with 95 braid coverage Pelco Manual C1992M A 12 03 5 MAINTENANCE If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel
3. inspect all system connections and cable runs To reduce the risk of electrical shock do not remove the cover or the back No user serviceable parts are inside Refer servicing to qualified personnel or contact the Pelco Customer Service Department for as sistance Refer to the Warranty and Return Information section SPECIFICATIONS ELECTRICAL Input Voltage 100 240 VAC 50 60 Hz automatic switching Power Consumption 49 watts Horizontal Resolution 350 TV lines Visual Picture Size 10 inch diagonal Sweep Linearity 10 Speaker Output 1 0 watt 3 dBV GENERAL Input Output Video 1 BNC input 75 ohms or Hi Z 1 looping output Audio 1 RCA input Hi Z 1 looping output S Video 1 DIN input 1 looping output Construction Steel cabinet Finish Black Dimensions 10 25 W x 10 63 H x 11 62 D inches 26 03 x 27 00 x 29 51 cm Weight 19 Ib 8 6 kg ENVIRONMENTAL Operating Temperature 32 to 106 F 0 to 41 C Humidity 0 to 90 non condensing Design and product specifications subject to change without notice 6 Pelco Manual C1992M A 12 03 REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance wi
4. 100 240 VAC 50 60 Hz is automati cally detected upon power up All image adjustment controls are conveniently located on the front panel of the monitor Pelco Manual C1992M A 12 03 3 INSTALLATION The monitor may be placed on any flat surface desk or table or rack mounted To rack mount the moni tor follow the instructions supplied with the rack mount kit 1 Video Cable Connection Refer to Table A for video coaxial cable requirements a Connectthe video cable to the BNC video input labeled V1 IN on the back panel of the monitor b Looping Operation Only Connect a video cable to the BNC connector labeled V1 OUT 2 Impedance Switch Setting a Terminating Operation Only Set the termination switch to the 75W position b Looping Operation Only Set the impedance switch to the Y C HI position looping 3 Plug the power cord provided into the AC INLET connection on the back panel Plug the other end of the cord into a power receptacle 6660020 VOLUME SHARP BRIGHT CONT COLOR TINT FRONT YIC HI S VIDEO IN 8 ol 750 AU1 OUT S VIDEO OUT Figure 1 Model PMC10A 10 inch Color Monitor Front and Back Panels 4 Pelco Manual C1992M A 12 03 OPERATION 1 Setthe video format switch located on the front panel to one of the following settings VIDEO Composite Video NTSC mode S VIDEO Use if the S VIDEO input jack on the rear of the monitor is used 2 Turn the monitor ON
5. PELLO Installation Operation PMC10A High Resolution Color Monitor C1992M A 12 03 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 IMPORTANT SAFEGUARDS AND WARNINGS Operate this unit only from the type of power source indicated on the label Do not block or cover ventilation openings on the back or bottom of the monitor cabinet Do not place this monitor near a radiator or heating vent Do not push objects of any kind through cabinet openings This may result in fire or electrical shock Before adding attachments always ask a service technician to perform routine safety tests to deter mine that equipment is in safe operating condition Ground potential tests should be part of the rou tine safety check made by the service technician Do not place monitor on an unstable cart stand or shelf where it may fall and injure personnel or damage equipment Route power cords so that they cannot be walked upon or tripped over Do not allow anything to rest on the power cord Do not install monitor in wet areas or where it may be exposed to rain or water Do not spill liquid of any kind on the unit Unplug the power cord from the unit before cleaning the display Use only a damp cloth Do not use alcohol spirits or ammonia to clean the display DO NOT ATTEMPT TO CLEAN
6. aler to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state f a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified w
7. arranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products e ne year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight repaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s iability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the De
8. ith the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2000 Pelco All rights reserved REVISION HISTORY Manual Date Comments C1992M 11 00 Original version 1 01 Revised to include ETL cETL and CE certifications and warnings C1992M A 12 03 Revised monitor dimensions for height to 10 63 inches 27 00 cm 8 Pelco Manual C1992M A 12 03
9. th the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particu lar installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the in terference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Pelco Manual C1992M A 12 03 7 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year w
Download Pdf Manuals
Related Search