Pelco MLZ6DT User's Manual
Contents
1. PELLO MLZ6DT Motorized Zoom Lens Control Installation Operation Manual C517M Rev C 6 92 1 0 WARNINGS CAUTION RISH OF ELECTRIC SHOCK Prior to installation and use of this product the following WARNINGS should be observed DO NOT OPEN This symbol indicates that there are important operating and mainte nance instructions in the literature accompanying this unit 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture The product bears the following marks Only use replacement parts recommended by Pelco After replacement repair of this unit s electrial components conduct resistance measurements between line and exposed parts to verify the exposed parts have not been connected to line circuitry This symbol indiates that dangerous voltage constituting a risk of electric shock is present within this unit Please thoroughly familiarize yourself with the infor mation in this manual prior to installation and opera tion CAUTION TO REDUCED THE RISK OF ELECTRIAL SHOCK DO NOT REMOVE COVER NO USER SERVICE ABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Pelco 3500 Pelco Way Clovis CA 93612 5699 e USA www pelc2. or 230 VAC 50 60 Hz Output Voltage 2 12 VDC Power Consumption 3 6 watts Power Supply 24 VAC CT 400 mA wall mount transformer MLZ6DT Output Connector AMP CPC type 14 pin mate sup plied Circuit Full wave power supply with solid state drive Cable Requirements Four 4 conductors plus ground one 1 additional conductor for manual override ZOOM FOCUS IRIS TELE NEAR UPEN SPEED WIDE FAR CLOSE Cable Distances The following distances are approxi mate maximum recommended under the following conditions Based on a 35mA load 9 VDC Single lens function activation Single common conductor in lens cable 10 loss in voltage 22 Awg 797 feet 243 m 20 Awg 1 267 feet 386 m 18 Awg 2 015 feet 614 m GENERAL Construction Cover Steel black polyester powder coat Chassis Steel zinc plated Panel Aluminum black polyester powder coat with white silkscreen Dimensions See Figure 6 Weight Unit Shipping MLZ6DT Series 3 Ibs 1 35kg 5 lbs 2 25 kg MLZA6DT Series 4 lbs 1 8kg 6 lbs 2 7 kg Rating NEMA 1 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 6 MLZ6DT Dimension Drawing Pelco Manual C517M Rev C 6 92 9 0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this wa
3. to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment Pelco Manual C517M Rev C 6 92
4. e individual con the connector by twisting the locking collar until it ductors item 3 snaps into position Refer to Figure 2 for wiring diagram threaded end of cable clamp gt STRIP 1 8 s lt STEPS 3 7 TOT CRIMP INSULATION OUTSIDE JACKET OF CABLE ITEM 5 DETAIL 26 FRONT VIEW 16 PIN CONNECTOR FRONT VIEW FRONT VIEW 37 PIN CONNECTOR 28 PIN CONNECTOR THE MOST COMMONLY USED CONNECTOR PIN OUT CONFIG URATIONS ARE SHOWN HERE REFERENCE THE CONNECTOR _ DRAWING APPLICABLE TO n 1 ae YOUR SITUATION FRONT VIEW FRONT VIEW 14 PIN CONNECTOR 9 PIN CONNECTOR Figure 1 Connector Assembly Pelco Manual C517M Rev C 6 92 3 MANUAL IRIS _ 5 BLUE LENS COM ZOOM CONTROL P3 OUTPUT LENS INPUT NO CONNECTION REQUIRED EXCEPT WHEN USED WITH A1700 ALLOWS MANUAL IRIS CONTROL Figure 2 Wiring Diagram for Output Pin Assignments 4 Pelco Manual C517M Rev C 6 92 5 0 OPERATION AND SYSTEM TEST 1 Hook up the control cable between the output con nector on MLZ6DT and the input connector on the lens see Figure 3 Check that the video is connected from the camera to the monitor Plug the mating connector of the wall mount trans former into the back of the MLZ6DT and plug the transformer into a 120 VAC source The power in dicator LED will light when power is applied For manual operati
5. is warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned
6. nits can be mounted side by side in one desk top chassis Rack mount kit for up to three 3 control modules Pelco Manual C517M Rev C 6 92 4 0 INSTALLATION 4 The contact pins supplied with the mating connec tor are the crimp type which may also be sol 4 1 CONNECTOR ASSEMBLY dered if you so desired item 4 Installation and or testing will require you to assemble 5 After crimping or soldering the contact pins to the the connector parts provided Fabricate the intercon conductors push them into the proper holes in the necting cable according to the following steps refer connector until they snap in place ence Figure 1 NOTE Contacts cannot be removed from the 1 Slide part A of the cable clamp item 1 over the end connector without the use of the appropriate of the cable item 1 part C with the threaded end AMP extraction tool which is available from of the cable clamp facing the connector item 5 Pelco 2 If the cable has a diameter less than 1 2 inch 1 3 6 Slide part A of the cable clamp toward the connec cm slide the rubber boot item 2 over the end of tor and screw the parts together Attach part B item the cable and pull through the cable clamp to so that 1 onto part A and connect both parts with the the boot encases the cable and forms a good seal screws provided 3 Strip back the cable jacket approximately 1 1 4 7 Connect the cable assembly to the unit and seat inches 3 2 cm and separate th
7. o com 800 289 9100 or 1 559 292 1981 FAX 800 289 9150 or 1 559 292 3827 International customers call 1 559 292 1981 or FAX 1 559 348 1120 2 0 SCOPE The information contained within this manual covers the MLZ6DT Motorized Zoom Lens Control with the 24 VAC wall mount transformer power supply 3 0 DESCRIPTION The MLZ6DT is a desk top zoom lens control which provides remote control of zoom focus and iris func tions for all Pelco motorized zoom lenses The MLZ6DT can also be used with lenses equipped with the AI700 AI701 auto iris servo assembly The servo in the AI700 AI701 detects the slightest change in video level and drives the iris motor to open or close the iris to maintain proper faceplate illumina tion The MLZ6DT control allows for manual override of the auto iris functions for scenes requiring manual iris adjustment Front panel switches provide control of zoom and fo cus functions with optional manual control of the iris Speed is adjustable through the front panel knob con trol 3 1 OPTIONS AI701 CO6HWC DT200 R300 Auto iris servo for motorized zoom lenses with ND and MS in suffix Allows for fully automatic iris opera tion with manual override when used with MLZ6DT lens control Pre wired 6 foot 1 82 m intercon necting with 14 pin control connec tor and butt splices on mating end Compatible only when notused with the AI701 UL Dual desk top mount kit two u
8. on put the switch in the MANUAL position Observing the monitor test for proper operation of zoom focus and iris func tions with related switches on the front panel Test for fast and slow speeds of all functions by observing their operation as the LENS SPEED knob on the front panel is adjusted WALL MOUNT TRANSFORMER NOTE AUTO operation only works in con junction with AI700 or AI701 auto iris servo units If the lens is equipped with AI700 or AI701 use the following guidelines to test auto operation see Figure 4 6 Connect the AI700 or AI701 as shown in Figure 4 Put the power switch in the AUTO ON position The IRIS switch should not operate ZOOM and FO CUS switches should operate normally Observing the monitor test operation of ZOOM and FOCUS switches Next turn the lens toward a dark area and observing the monitor check that the iris opens Move the lens back toward a lighter area and ob serving the monitor check that the iris closes 6 0 MAINTENANCE Under normal operating conditions and usage mainte nance of this equipment is not necessary However if maintenance should be required consult Pelco or a qualified service technician COAX CABLE Figure 3 Basic System Configuration WALL MOUNT TRANSFORMER COAX CABLE e CONTROL CABLE AI700 REQUIRES EXTERNAL POWER SUPPLY Figure 4 System Configuration Using AI700 or AI701 Auto Iris Servo Pelco Man
9. rranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners includ ing when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications thatis preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under th
10. ual C517M Rev C 6 92 7 0 SCHEMATIC hp VNL lt 84O NSZ 33n000L LO T evLyN LY NSZ 3n000L cO SOOFPNL SOOPNL i 8d SOOPNL SOOPNL M Za LONI OWA r Id 9a K sq L q31 A 2 MZ L AL ozH SI I SN904 WOOZ S N NOWWOS SN31 SIHI OLNVY AD OL MEILT LLY A esau RN e za SYL6NL A va 8L so Z O MEIL OLY SYL6NL ta bd ed 84 bdOLPZLOW Ln ZLSONZ id MOL vlY T ozs gly kq NMOHS SNOI1VOO1 NI SYadWnr WHO Otz3Z TIVLSNI 618 aor ku LIAN qa3dS L GALYSAN l TYWYON ASZ x qaadS qQ3SO1O N3dO dvd UVAN ddim 3131 O1nV TWONVI YMS Figure 5 MLZ6DT Schematic Pelco Manual C517M Rev C 6 92 8 0 SPECIFICATIONS CONTROLS Zoom Paddle switch TELE WIDE Focus Paddle switch NEAR FAR Manual Iris Paddle switch OPEN CLOSE Auto Iris Paddle switch AUTO MANUAL Video Level Knob adjustment MLZA6DT only Speed Knob adjustment On Off Rocker switch Pilot Lamp Light emitting diode LED MLZ6DT Long life neon MLZA6DT ELECTRICAL Input Voltage 120
Download Pdf Manuals
Related Search