Pelco IP3701H-2 User's Manual
Contents
1. 86 m from the transformer would require a minimum wire gauge of 20 AWG NOTE Wire gauges are standard AWG or metric sizes Distances are calculated in feet values in parentheses are meters C2941M C 6 08 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS 1 2 3 5 Set the lens mode selector switch to AIV Switch the electronic shutter control ESC and automatic gain control AGC OFF Refer to the lens instructions and adjust the lens for the optimum picture video output level of 1 Vp p Focus the lens a Completely open the iris by covering the lens with a suitable neutral density ND filter b If the viewed scene is 6 5 ft 2 m away or farther set the lens focus to infinity far C Use the back focus adjustment ring refer to Back Focus Adjustmenton page 15 and focus on he selected scene d Remove the ND filter and set the lens focus as required Set the AGC switch to ON as required Most scenes benefit from AGC NOTE For best results outdoors use an ND3 filter DIRECT DRIVE DC AUTO IRIS LENS 1 2 3 5 Set the lens mode selector switch to AID default setting Set the ESC and AGC switches to OFF Use an appropriate screwdriver to completely turn the lens level potentiometer clockwise Slowly adjust the potentiometer counterclockwise until the optimum picture is obtained video output level of 1 Vp p Focus the lens a Completely open the iris by covering the lens2. Image flickering Flickerless setting e Verify DIP switch settings e Verify power supply specifications e Replace camera with a working camera If the new camera does not work contact Pelco Product Support at 1 559 292 1981 or 1 800 289 9100 Unable to sync to an Endura system manager or NTP server after changing networks Network connectivity issues e Disconnect the power cable either PoE or 24 VAC and then reconnect it to the camera Power is indicated by the LED The LED will flash green five times per second for approximately two minutes if the camera has power e Reset the camera s factory defaults Refer to Reset Button on page 9 20 C2941M C 6 08 Specifications GENERAL Construction Finish Imaging Device Picture Elements 1P3701H 2 1P3701H 2X Sensing Area Horizontal Resolution Iris Control Minimum Illumination ESC Signal to Noise Ratio Backlight Compensation Scanning System 1P3701H 2 1P3701H 2X Auto Iris Lens Type Unit Weight ELECTRICAL Ports Cabling Type Input Voltage Power Consumption MECHANICAL Lens Mount Camera Mount VIDEO Signal System Compression Video Streams Video Resolutions ACIF 2CIF CIF QCIF Bit Rate Configurable Video Access from Web Browser Users Minimum Web Browser Requirements RAM Ethernet Card Web Browser Screen Resolution C2941M C 6 08 Black polyester powder coat 1 3 inch imager 768 H x 494 V 752 H
3. x 582 V 6 mm diagonally 480 TV lines Electronic passive 0 5 lux f 1 2 40 IRE AGC on 75 reflectance 1 60 to 1 100 000 second 52 dB AGC off Selectable by DIP switch setting 525 lines 2 1 interlace 625 lines 2 1 interlace DC video control selectable by DIP switch position 2 2 lb 1 0 kg RJ 45 connector for 100Base TX Auto MDI MDI X Autonegotiate manual setting Cat5 or better for 100Base TX 24 VAC 18 30 or PoE IEEE802 3af 7 W maximum C CS mount adjustable Use 1 4 20 screw top or bottom of camera housing NTSC or PAL MPEG 4 MJPEG in Web viewing mode 3 simultaneous NTSC PAL 704 x 480 704 x 576 704 x 240 704 x 288 352 x 240 352 x 288 176 x 120 176 x 144 20 kbps to 2 Mpbs per stream implements EnduraView Camera live view for up to 10 video sources 10 simultaneous users unlimited number of users using multicast PC Pentium 4 microprocessor 1 6 GHz with Windows 98 Windows 2000 Windows XP or later or Mac OS X 10 3 9 or later 512 Mby 100 Mbi Internet Explorer 5 5 or later or Firefox 1 5 or later 1024 x 768 pixels or higher 16 or 32 bit pixel color resolution o 21 22 ENVIRONMENTAL Operating Temperature Storage Temperature PHYSICAL Dimensions Weight without lens 14 to 122 F 10 to 50 C 14 to 158 F 10 to 70 C 4 54 D x 2 64 W x 3 06 H 11 53 x 6 71 x 7 77 cm 1 01 Ib 0 46 kg Design and product specifications subje
4. 400 Series LCD monitors e Two years on standard motorized or fixed focal length lenses e Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products e Two years on Spectra III Spectra Mini Esprit ExSite and PS20 scanners including when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Two years except lamp and color wheel on Digital Light Processing DLP displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty e Two years on Intelli M elDC controllers e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negli
5. lens The camera is factory set for a CS mount lens but is easily adjusted for a C mount lens 1 mount lens only Completely rotate the back focus adjustment counterclockwise before installing the C mount lens refer to Back Focus Adjustment on page 15 2 Set the lens mode selector switch on the side of the camera to AIV auto iris video drive lens or AID auto iris DC drive lens Refer to Switch Settings on page 16 Switch settings are determined by the type of lens used 3 Screw the lens onto the lens mount Be careful to prevent dust from entering the space between the lens and the CCD element If necessary use clean compressed air to remove any foreign matter 4 Connect the auto iris lens to the 4 pin connector located on the side of the camera Pin connections for the iris drive connector are as follows 4 d PIN DC AID AUTO IRIS LENS VIDEO AIV AUTO IRIS LENS 1 Control coil negative Lens positive supply 2 Control coil positive Not used 3 Drive coil positive Video drive signal 1 2 4 Drive coil negative Ground CAMERA MOUNTING Use a standard 1 4 20 screw provided with a maximum thread length of 3 8 inch 10 mm for mounting to the top or bottom of the camera C2941M C 6 08 Wiring Tables CAT5 CABLE Connect a Cat5 cable to the RJ 45 network connector The 8 pin connector includes video and PoE for the camera PoE IEEE 802 3af injects power over the same cabling
6. may be subject to a 20 percent restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid 1 8 08 REVISION HISTORY Manual Date Comments C2941M 8 07 Original version C2941M A 1 08 Added Open Source Software Notice C2941M B 4 08 Removed referenced to JRE per CN21185 C2941M C 6 08 Changed static IP address to new default 192 168 0 20 per CN 21530 Pelco the Pelco logo Camclosure DigitalSENTRY Endura Esprit ExSite Genex Intelli M Legacy and Spectra are registered trademarks of Pelco Inc Spectra Ill is a trademark of Pelco Inc O Copyright 2008 Pelco Inc All rights reserved DLP is a registered trademark of Texas Instruments Incorporated Microsoft Windows and Internet Explorer are registered trademarks of Microsoft Corporation Firefox is a registered trademark of the Mozilla Foundation Pentium is a registered trademark of Intel Corporation PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Australia Finland France Germany Italy Macau The Netherlands Russia Singapore South Africa Spain Sweden United Arab Emirates United Kingdom United States
7. that carries the network data eliminating the need for a separate power supply This simplifies the installation and operation of the camera without any degradation of network performance Refer to Table B for pin descriptions Table B Pin Descriptions Pin Function 1 TX 2 TX 3 RX 4 PoE 1 2 5 PoE 1 2 6 RX 7 PoE 3 4 8 PoE 3 4 24 VAC AND BNC CONNECTIONS OPTIONAL If PoE is not used the camera includes a 24 VAC power connector Connect the power cable to the 2 pin power connector on the back of the camera using the terminal block connector provided Refer to Table C for the recommend wire gauge and wiring distances The power supply connector is shown in Figure 6 Use only a Class 2 isolated power supply Refer to Specifications on page 21 for power consumption CLASS 2 ISOLATED POWER SUPPLY Figure 6 Power Supply Connections C2941M C 6 08 11 The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices Table C Recommended Wire Gauge and Wiring Distances Total 20 18 16 14 12 10 VA 0 5 mm 1 0mm 1 5mm 2 5mm 4 0 mm 6 0 mm 10 283 451 716 1142 1811 2880 86 137 218 348 551 877 For example a camera that requires 10 VA and is installed 283 ft
8. 03 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada C2941M C 6 08 Description The IP3701H 2 Series is a high resolution color video camera with a built in 100Base TX network interface for live streaming to a standard Web browser Microsoft Internet Explorer or Firefox The camera features open architecture connectivity for third party software recording solutions and is also Endura Enabled to record manage configure and view multiple live streams The camera also includes built in Power over Ethernet PoE which supplies power to the camera through the network If PoE is not available the camera is prewired for 24 VAC Before installing your camera thoroughly familiarize yourself with the information in this manual MODELS 1P3701H 2 1P3701H 2X High resolution 480 TV lines SuperHAD CCD minimum illumination of 0 5 lux at f 1 2 and 40 IRE NTSC High resolution 470 TV lines SuperHAD CCD minimum illumination of 0 5 lux at f 1 2 and 40 IRE PAL C2941M C 6 08 Basic System Configurations IMPORTANT NOTE PLEASE READ The network implementations in this document are shown as general representations only and are not intended to show detailed network topologies Your actual network will differ requiring changes or perhaps additional network equipment to accommodate the systems as illustrated Please contact your local Pelco Representative to discuss your specific require
9. 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference o radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You may also find helpful the following booklet prepared by the FCC How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission s rules This Class B digital apparatus complies with Canadian ICES 0
10. INSTALLATION IP3701H 2 Series IP Color Camera C2941M C 6 08 Contents important Safety Instructions st e abad Aa au 4 Open Source Software Notice 4 Regulatorn Notices mini aa Dati i Pa a o 35 du pa 33 a i da die de 5 Vid o Quality Cautions esa A a 5 Frame Rate Notice Regarding User Selected Options ccm 5 DESCUIDO acacia le Sate e aaa daf t aut mara e acut d a i iu ba add n e inta 6 Models ceo cai A a Icar Pi oa e gl Sans 6 Basic System Configure aa a ea a aa dev e dat e ea a i Aaa ia ds 7 Camera La volt Mot 2 pai Da tesa Oita ainda A 3 0 piata A 7 tad Boa SaaS a 9 Reset Button eto A ad dad 9 Installation ze ocazia a dba ea aaa Beare das 0 A O on Rt ay a e 0 Camera Mountings ona tas 0 Wiring Tables toca a tna hoe tate we Gada el fated ei ead ed ceed 1 E ana Amini ie d ba vided ea i aa fe Saye Baw pane E Ea 1 24 VAC and BNC Connections optional 1 Lens Setup and Focus Procedures 0 20 00 0 occ cece cece corr 3 Video Drive Auto Iris Lens 2 0 0 0 ccc cece cee e earren eens 3 Direct Drive DC Auto Iris Lens 13 Fed ans A fe cee soe Cass oo Oe fede BONG os Oh pie wena dee pe ae muon aes 3 Ma nual lris lens n 2 220 net ena ned ta ase kieed SO ais 4 LO OS it o a A Pena 2 data ap rac nt an dete tinge e 4 Back Focus Adjustment 2 221 035 e eee Senay bade ceded scab eed nn beac Da a ia 5 Switch Settings A oh Ue say oh Oh dees wags bleed Ede n a 6 Dynamic Range nd EDRE iire rito
11. US ADJUSTMENT LOCKING SCREW BNC VIDEO SERVICE CONNECTOR LENS CONNECTOR DIP SWITCHES COVER REMOVED Figure 5 Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following modes Table A Reset LED Status Mode Function Unit Status Indicator Light Configuration Starts reset LED Flashes green selection sequence Reboot Restarts the unit Flashes green and red simultaneously when entering this mode The LED flashes green when mode is selected and during reboot Reset Resets unit to factory Flashes red when entering this mode Flashes red when default settings and mode is selected and then flashes green when camera then restarts unit restarts Camera is offline during reset mode Cancel Cancels any Is not lit configuration or reset action To access one of these modes 1 Press and hold the reset button The unit starts cycling through the modes hold the button for four seconds to access cycle through each mode The unit status indicator flashes the color for the current mode refer to Table A 2 When the color of the desired mode appears release the button NOTES e If there is no configuration activity for 15 minutes the camera will automatically exit the reset mode e The LED is not lit during normal operation C2941M C 6 08 9 Installation LENS MOUNTING The camera can be used with a fixed iris manual iris or auto iris
12. ct to change without notice Green Directive 2002 95 EC The materials used in the manufacture of this document and its components are compliant to the requirements of This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment C2941M C 6 08 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on fiber optic products and TW3000 Series unshielded twisted pair UTP transmission products e Three years on Spectra IV products e Three years on Genex Series products multiplexers server and keyboard e Three years on DX Series digital video recorders DVR5100 Series digital video recorders DigitalSENTRY Series hardware products DVX Series igital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products e Three years on Camclosure and Pelco branded fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty e Three years on PMCL200 300
13. e EDR OFF default setting Disables the EDR mode EDR Enables the EDR mode to help balance a scene with a large dynamic range Use this feature to improve the picture in washed out areas This feature adds 12X the dynamic range but also increases dark area picture noise Refer to Dynamic Range and EDR on page 17 for further details 110 Automatic white balance AW1 AW2 AW1 default setting Automatically processes the viewed image to retain color balance over a wide color temperature range AW2 Processes the viewed image to retain color balance in a restricted color temperature range Use only when AW1 causes an unbalanced color picture C2941M C 6 08 Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene A scene that ranges from bright sunlight to deep shadows has a high dynamic range while indoor scenes with less contrast have a low dynamic range The extended dynamic range EDR feature will help capture the entire range of the scene This feature can achieve 12X the improvement in dynamic range In scenes with very high dynamic range the EDR feature will exhibit a higher noise level than when the feature is turned off This is normal and is not a malfunction NOTE Depending on the scene contrast it may or may not be possible to capture the entire range with any camera Careful camera placement should be considered in extreme cases 18 C2941M C 6 08 Troubleshoo
14. e used to improve picture quality in a fixed scene Automatic gain control AGC OFF Disables the AGC mode AGC default setting Enables the AGC mode Automatically adjusts the image to compensate for changes in light levels Most scenes benefit from AGC operation Optima OPT OFF default setting OPT Boosts the video by 3 dB Only use this feature if the video signal appears weak on your monitor Electronic shutter control ESC OFF Disables the ESC mode ESC default setting Enables the ESC mode The ESC function automatically changes the sensitivity of the camera by varying the electronic shutter speed according to the amount of incident light Electronic shutter speed range is 1 60 to 1 100 000 This feature should only be used with AID or manual iris lenses Do not use with an AIV type lens Auto iris lens mode selector AIV AID AIV Video controlled auto iris lens Disable the ESC mode when using an AIV type lens AID default setting DC controlled auto iris lens NOTE The switch setting is determined by the type of lens used Not Used Normal sharpness and sharpness NOR SHP NOR default setting Sets the camera to normal sharpness mode SHP Enables the Sharpness mode Enhances picture detail by increasing the aperture gain of the camera sharpening the edges in the picture In some scenes the SHP mode will increase edge noise on your monitor C2941M C 6 08 Not Used O Extended dynamic rang
15. gence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment PO number sales order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS To expedite parts returned for repair or credit please call Pelco at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair and designated return location All merchandise returned for credit
16. ments CABLE MODEM ROUTER SWITCH WITH DHCP SERVER vlelelelvlvlviviclunne TCP IP INTERNET CAMERA CAMERA WEB 3rd PARTY BROWSER RECORDING SOLUTION E EEE SAA NOTE FOR A SECURE NETWORK PELCO RECOMMENDS DHCP NETWORK PLACING THE IP3701H CAMERA BEHIND A FIREWALL Figure 1 DHCP Network Example ENDURA CAMERA WEB BROWSER eee Figure 2 Endura Network Example C2941M C 6 08 NETWORK SWITCH OMOOOOMMOO ax CAMERA IF NOT DHCP CAMERA IS ASSIGNED DEFAULT IP ADDRESS 192 168 0 20 ON NETMASK 255 255 0 0 WEB BROWSER Se PRIVATE NETWORK B PC ACTS AS SERVER CAMERA Figure 3 Private Network Example CABLE MODEM ROUTER SWITCH DHCP SERVER DISABLED e o o o o o DODOOOOODa CAMERA 1 FIXED BUT El UNIQUE IP ADDRESS SAME SUBNET MASK AS COMPUTER CAMERA TCP IP INTERNET a CAMERA 2 FIXED BUT UNIQUE IP ADDRESS E LL SAME SUBNET MASK AS COMPUTER CAMERA WEB 3rd PARTY BROWSER RECORDING SOLUTION EI ESA STATIC NETWORK FIXED BUT UNIQUE IP ADDRESS NOTE FOR A SECURE NETWORK PELCO RECOMMENDS SAME SUBNET MASK AS CAMERAS PLACING THE 1P3701H SERIES CAMERA BEHIND A FIREWALL Figure 4 Static Network Example 8 C2941M C 6 08 Camera Layout TOP MOUNT LENS LEVEL ADJUSTMENT NETWORK CONNECTOR POWER CONNECTOR LEDs 0 RESET BUTTON O BACK FOCUS ADJUSTMENT RING BACK FOC
17. nd view a distant object 3 Adjust the back focus adjustment ring until the object is in focus refer to Back Focus Adjustment on page 15 4 Zoom in completely and adjust the lens focus until the object is again focused 5 Repeat these steps until the full zoom range may be viewed with the minimum loss of focus NOTE For best results outdoors use an ND3 filter 14 C2941M C 6 08 Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case To adjust the back focus 1 Loosen the two back focus locking screws one on each side 2 Turn the back focus ring until the object is in focus 3 When the back focus adjustment is satisfactory tighten the locking screws Do not overtighten the locking screw or force the back focus adjustment ring wise oC oun c BACK FOCUS ADJUSTMENT BACK FOCUS LOCKING SCREW ADJUSTMENT 7 RING goc Figure 7 Back Focus C2941M C 6 08 15 Switch Settings Figure 8 DIP Switch Default Settings NOTES 90 White indicates the switch setting Under most conditions you will not be required to set any switches Backlight compensation BLC OFF default setting Disables the BLC mode BLC When in the ON position BLC is enabled If a bright backlight is present the objects in the picture may appear dark or as a silhouette BLC enhances objects in the center of the picture and can b
18. o dark Installation error black image Make sure the lens cover in not installed Make sure camera is not located in an environment with zero light Use a service connector to check camera operation Connect one en connector to the BNC serv d of the service ice connector on the camera Connect the other end of the service connector to a monitor Replace camera with a wo rking camera If the new camera does not work contact Pelco Product Support at 1 559 292 1981 or 1 800 289 9100 C2941M C 6 08 Problem Possible Cause Suggested Remedy Image too light Installation error e Verify DIP switch settings e Use a service connector to verify camera operation Connect one end of the service connector to the BNC service connector on the camera Connect the other end of the service connector to a monitor e Replace camera with a working camera If the new camera does not work contact Pelco Product Support at 1 559 292 1981 or 1 800 289 9100 Image only displays in black white Color level setting e Verify DIP switch settings e Use a service connector to verify camera operation Connect one end of the service connector to the BNC service connector on the camera Connect the other end of the service connector to a monitor e Replace camera with a working camera If the new camera does not work contact Pelco Product Support at 1 559 292 1981 or 1 800 289 9100
19. re Notice This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License GPL GNU Library Lesser General Public License LGPL and different and or additional copyright licenses disclaimers and notices The exact terms o to the exact terms GPL LGPL and some other licenses are provided to you with this product Please refer of the GPL and LGPL at http www fsf org Free Software Foundation or http www opensource org Open Source Initiative regarding your rights under said license You may obtain a complete corresponding machine readable copy of the source code of such software under the GPL or LGPL by sending your request to digita support pelco com the subject line should read Source Code Request You will then receive an e mail with a link for you to download the source code This offer is valid or a period of three 3 years from the date of the distribution of this product by Pelco C2941M C 6 08 Regulatory Notices This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference eceived including interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part
20. s cada d ta cara la ee sual Weel dee we alate add teks 8 TrOUDIESHOOLING cc Geechee hea gk he eee ee Boats ei ek ute Sed sed ee ee ee 9 SECC a A aed e o 21 C2941M C 6 08 3 Important Safety Instructions 1 Read these instructions instructions Do not use this apparatus near water Do not block any ventilation openings Install in accordance with the manufacturer s instructions Only use attachments accessories specified by the manufacturer Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 2 Keep these 3 Heed all warnings 4 Follow all instructions 5 6 7 8 9 In stallation should be done only by qualified personnel and conform to all local codes 0 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 1 Use only installation methods and materials capable of supporting four times the maximum specified load 2 Use stainless steel hardware to fasten the mount to outdoor surfaces 3 Only use replacement parts recommended by Pelco 4 After replacement repair of this unit s electrical components conduct a resistance measurement between the line and exposed parts to verify the exposed parts have not been connected to the line circuitry Open Source Softwa
21. ting Problem Possible Cause Suggested Remedy No video PoE power issue Verify Cat5 cable connection Verify PoE is enabled Disconnect the Cat5 cable reconnect the cable Powe from the PoE and then ris indicated by the LED The LED will flash green five times per second for approximately two minute power s if the camera has Power issue 24 VAC Network connectivity issues Verify the 24 VAC power s upply connection Disconnect the network cable and then reconnect it to the camera Power is indicated by the LED The LED will flash green five times per second for approximately two minute power s if the camera has Verify network cable connections Disconnect the network cable and then reconnect it to the camera Power is The LED will flash green approximately two minute power Replace network cable wi indicated by the LED ive times per second for s if the camera has h new cable If new cable does not work contact Pelco Product Support at 1 559 292 198 or 1 800 289 9100 Defective camera Use a service connector to verify camera operation Connect one en connector to the BNC serv d of the service ice connector on the camera Connect the other end of the service connector to a monitor Replace camera with a wo rking camera If the new camera does not work contact Pelco Product Support at 1 559 292 1981 or 1 800 289 9100 Image to
22. with a suitable ND filter b Select the scene to be viewed c If the viewed scene is 6 5 ft 2 m away or more set the lens focus to infinity far d Use the back focus adjustment ring refer to Back Focus Adjustment on page 15 and focus on the selected scene e Remove the ND filter and set the lens focus as required When finished set the ESC and AGC switches to ON NOTE For best results outdoors use an ND3 filter FIXED LENS NO IRIS 1 2 Set the ESC and AGC switches to ON default settings Focus the lens a Setthe lens focus to infinity and view an image more than 6 5 ft 2 m away b Focus the image with the back focus adjustment ring refer to Back Focus Adjustment on page 15 c Set the lens focus as required C2941M C 6 08 13 MANUAL IRIS LENS 1 Set the ESC and AGC switches to ON default settings 2 Focus the lens a Open the iris fully and set the lens focus to infinity b View an image more than 6 5 ft 2 m away c Focus the image with the back focus adjustment ring refer to Back Focus Adjustment on page 15 d Adjust the lens focus and set the iris if equipped for the best picture quality The largest aperture gives the best light sensitivity the smaller the aperture the greater the depth of field ZOOM LENS 1 Set the lens focus to infinity far and completely open the iris by covering the lens with a suitable ND filter 2 Zoom out to the widest field of vision a
Download Pdf Manuals
Related Search