Pelco C1303M-B User's Manual
Contents
1. enclosure VAN TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE C1303M B 5 05 MAY BE PRESENT Getting Started Thank you for purchasing Pelco s ExSite Series explosionproof integrated positioning system This manual includes instructions for installing the camera module for the ExSite Series system For complete system installation instructions refer to the installation manual placed in the pan and tilt box WARNING Do not connect the power module to a supply circuit unless all ExSite system components pan and tilt camera module and power module are installed Once the complete system is installed refer to the operation programming manual shipped with the camera module for instructions on how to operate and program your system C1303M B 5 05 Installation To install the camera module do the following 1 Refer to Figure 1 Loosen the set screw at the back of the enclosure with the provided 1 5 mm Allen wrench Figure 1 Loosen Setscrew 2 Use the supplied spanner wrench to loosen the back of the camera enclosure refer to Figure 2 Once the back is loose use your hands to continue to loosen it until it can be removed AN WARNING To avoid thread damage carefully remove the back of the enclosure Never use force to remove the back of the camera enclosure CAMERA ENCLOSURE BACK SPANNER WRENCH Figure 2 Remove Back Cap of Enclosure C1303M B 5 05 3 Slid2. INSTALLATION ExSite Series Explosionproof Camera Module C1303M B 5 05 Important Safety Instructions 8 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not block any ventilation openings Install in accordance with the manufacturer s instructions To reduce the risk of ignition of hazardous atmospheres disconnect the equipment from the supply circuit before opening Keep assembly ightly closed when in operation The maximum ambient temperature range is 76 F to 140 F 60 C to 60 C Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Installation should be done only by qualified personnel and conform to all local codes Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moi
3. TSC PAL Scanning System 2 1 interlace 2 1 Interlace Image Sensor 1 4 inch CCD 1 4 inch EXview HAD CCD Effective pixels NTSC 724 H x 494 V 768 H x 494 V PAL 724 H x 582 V 752 H x 582 V Horizontal Resolution NTSC gt 470 TV lines gt 470 TV lines PAL gt 470 TV lines gt 460 TV lines Lens F1 6 f 3 6 82 8 mm optical F1 6 f 4 88 mm optical Zoom 23X optical 10X digital 22X optical 12X digital Zoom Speed 2 9 4 2 5 8 seconds 2 4 3 9 6 3 seconds Horizontal 54 at 3 6 mm wide zoom 47 at 4 0 mm wide zoom Angle of view 2 5 at 82 8 mm telephoto zoom 2 2 at 88 mm telephoto zoom Focus Automatic with manual override Automatic with manual override Maximum Sensitivity at 35 IRE NTSC 0 08 lux at 1 2 sec shutter color 0 02 lux at 1 2 sec shutter 0 3 lux at 1 60 sec shutter B W PAL 0 013 lux at 1 2 sec shutter B W 0 08 lux at 1 1 5 sec shutter color 0 02 lux at 1 1 5 sec shutter 0 3 lux at 1 50 sec shutter B W 0 013 lux at 1 1 5 sec shutter B W Sync System nternal AC line lock phase adjustable via Internal AC line lock phase adjustable via remote remote control V Sync control V Sync White Balance Automatic with manual override Automatic with manual override Shutter Speed Automatic electronic iris Manual Automatic electronic iris Manual NTSC 1 2 1 30 000 1 2 1 30 000 PAL 1 1 5 1 30 000 1 1 5 1 30 000 Iris Control Automatic Iris Control with manual override Automatic Iris Control with manual override G
4. ain Control Automatic OFF Automatic OFF Video Output 1 Vp p 75 ohms 1 Vp p 75 ohms Video Signal to Noise gt 50 dB gt 50 dB Manual control of camera setup functions can be done with CM6700 CM6800 CM8500 CM9500 CM9740 CM9760 CM9770 CM9780 KBD200A KBD300A and MPT9500 controllers but not with CM7500 MPT9000 or KBD9000 controllers REVISION HISTORY Manual Date Comments C1303M 11 04 Original version C1303M A 2 05 Added maintenance section for camera module replacement C1303M B 5 05 Revised instructions for models with wipers Pelco and the Pelco logo are registered trademarks of Pelco Copyright 2005 Pelco All rights reserved ExSite and LowLight are trademarks of Pelco EXview HAD is a trademark of Sony Corporation C1303M B 5 05 11 PELLO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
5. e the camera module into the enclosure Refer to Figure 3 to position the camera module properly in the enclosure Carefully mate the camera s power connector to the mating connector located inside the enclosure Only models with wipers The tab located inside the enclosure must be pointing down before installing the camera module refer to Figure 3 To position the tab place the wiper located at the front of the enclosure in the center of the viewing window refer to Figure 4 AN WARNING Do not force the camera module into the enclosure ea CENTER NOTCHES CAMERA MODULE CAMERA ENCLOSURE CENTER WIPER Figure 4 Center Wiper C1303M B 5 05 4 Refer to Figure 5 and do the following to install the arm of the wiper a Place the supplied green bushing on the stud located behind the handle of the camera module The bushing should be in the same orientation as shown in Figure 5 b Install the wiper arm Place the ridge of the arm in the notch of the enclosure tab and the slot of the arm over the green bushing 5 Secure the arm of the wiper and the camera module with the supplied 8 32 Phillips flat head screw refer to Figure 5 SET TAB IN CENTER POSITION 8 32 PHILLIPS FLAT HEAD SCREW ARM CAMERA MODULE HANDLE BUSHING Figure 5 Install Wiper Arm A WARNINGS e To avoid thread damage carefully install the back cap to the enclosure e Never force the back cap onto the end
6. of the enclosure e When installation is completed there should be no gap between the back cap and the enclosure 6 Reinstall the back cap on the enclosure by doing the following a Use your hands and turn the back cap clockwise until you can no longer turn it with your hands The back cap should turn easily until it comes in contact with the O ring If it does not turn easily the threads are not aligned and thread damage will occur b Continue tightening the back cap with the supplied spanner wrench There should be no gap between the back cap and the enclosure when the back cap is tightened and properly installed c Once the back cap is installed secure the back cap with the set screw using the supplied 1 5 mm Allen wrench C1303M B 5 05 1 Maintenance CAMERA MODULE REPLACEMENT The ExSite camera module can be replaced only with a camera module with the same model number If a different camera model is installed in an existing system the system will not function and a message to contact the Pelco factory will appear on the screen A DANGER To reduce the risk of ignition of hazardous atmospheres disconnect the equipment from the power supply before opening Keep assembly tightly closed when operating To replace the camera module do the following 1 Remove the back cap of the camera enclosure Refer to Figure 6 and do the following a Loosen the set screw with a 1 5 mm Allen wrench b Use the supplied spanne
7. per C1303M B 5 05 6 Refer to Figure 7 and do the following to reinstall the arm of the wiper a b Reinstall the green bushing on the stud located behind the handle of the camera module Reinstall the wiper arm Place the ridge of the arm in the notch of enclosure tab and the slot of the arm over the green bushing 7 Secure the camera module and the wiper arm with the 8 32 Phillips flat head screw refer to Figure 7 A WARNINGS To avoid thread damage carefully install the back cap to the enclosure Never force the back cap onto the end of the enclosure When installation is completed there should be no gap between the back cap and the enclosure 8 Reinstall the back cap on the enclosure by doing the following a Use your hands and turn the back cap clockwise until you can no longer turn it with your hands The back cap should turn easily until it comes in contact with the O ring If it does not turn easily the threads are not aligned and thread damage will occur Continue tightening the back cap with the supplied spanner wrench There should be no gap between the back cap and the enclosure when the back cap is tightened and properly installed Once the back cap is installed secure the back cap with the set screw using a 1 5 mm Allen wrench C1303M B 5 05 Specifications Camera Day Night 23X Color LowLight 22X Color Signal Format NTSC PAL N
8. r wrench to loosen the back cap of the camera enclosure Once the back is loose use your hands to continue to loosen it until it can be removed CAMERA ENCLOSURE BACK SPANNER WRENCH Figure 6 Remove Back Cap of Camera Enclosure 2 Remove the 8 32 Phillips flat head screw that secures the camera module inside the enclosure refer to Figure 7 SET TAB IN CENTER POSITION 8 32 PHILLIPS FLAT HEAD SCREW ARM CAMERA MODULE HANDLE STUD BUSHING Figure 7 Remove or Install Camera Module 8 C1303M B 5 05 3 For models with wipers also remove the wiper arm and the green bushing from the unit see Figure 7 4 Slide the camera module out of the enclosure A WARNING Never force the camera module into the enclosure 5 Install the new camera module by doing the following Slide the camera module into the enclosure Refer to Figure 8 to position the camera module properly in the enclosure Carefully mate the camera s power connector to the mating connector located inside the enclosure Only models with wipers The tab located inside the enclosure must be pointing down before installing the camera module refer to Figure 8 To position the tab place the wiper located at the front of the enclosure in the center of the viewing window refer to Figure 9 e CENTER NOTCHES CAMERA MODULE CAMERA ENCLOSURE Figure 8 Install Camera Module CENTER WIPER Figure 9 Center Wi
9. sture Use only installation methods and materials capable of supporting four times the maximum specified load Use stainless steel hardware to fasten the mount to outdoor surfaces AN ALL POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building A readily accessible disconnect device shall be incorporated in the building installation wiring CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so Only use replacement parts recommended by Pelco The product and or manual may bear the following marks A This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit CAUTION This symbol indicates that there are important operating and maintenance instructions in the RISK OF ELECTRIC SHOCK literature accompanying this unit DO NOT OPEN A WARNING HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY WARNING To reduce the risk of ignition of hazardous atmospheres disconnect the equipment from the supply circuit before opening Keep assembly tightly closed when operating WARNING To reduce the risk of ignition of hazardous atmospheres conduit runs must have a sealing fitting connected within 2 inches of the
Download Pdf Manuals
Related Search