Pelco c2408M-F(4/03) User's Manual
Contents
1. 80 required It is also configured with 2 6 FL Flickerless OFF the shutter speed set at 1 60 w L AE Automatic exposure IB SWITCH POSITION NTSC or 1 50 PAL and AGC 8 Notused set at 6 dB of gain To enable automatic exposure Turn on switch 7 and then turn on off switch 4 for electronic shutter control switch 5 for backlight compensation and switch 6 for flickerless motion To manually set and lock AWB Place a white background in front of camera and turn off switch 1 For gamma correction Switch to accurately reproduce scene brightness when turned on y 7 0 6 and when turned off y 1 0 For gain control Switch 3 On increases gain by 6 dB and switch 3 Off increases gain by 18 dB To enable auto iris and manually set shutter speed Turn off switch 7 set switches 4 5 and 6 for the desired shutter speed CAUTION Do not change the shutter speed unless you understand how changing the settings will affect the scene detail Shutter Switch Number and Position Speed 7 6 5 4 1 60 NTSC 1 50 PAL en On en 1 100 Off On On 1 250 off On Off On 1 500 Off Off On 1 1000 On On Off 1 2000 Off On Off 1 4000 On Off Off 1 10000 Off Off Off Pelco Manual C2408M F 403 7 Switch Settings for Fixed Focal Length Lens with Auto Iris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used u2. is on use caution when adjusting the camera To adjust the focus 1 Loosen the locking screw on the bottom of the lens To ADJUSTMENT loosen the screw it may be necessary to remove the SCREW heater board Refer to the figure below and the accom panying steps Move the screw in the slot to bring the picture into focus Retighten the locking screw Replace the heater board if it was removed BOTTOM VIEW OF CAMERA WITH HEATER BOARD REMOVED ao oco m Reconnect the four pin heater connector if it was unplugged 6 Reinstall the camera if it was removed To remove the heater board if the heater connector is unplugged already go to step 4 1 Remove the camera from the mounting bracket 2 Disconnect the four pin heater connector red orange and black wiring in the base 3 Wait for the heater elements to cool if they are hot 4 Apply pressure and press on the corner of the board the proper hole of the mounting bracket If the camera is not installed in the correct WARNING To prevent damage to the camera or lens the camera must be installed in hole the window of the enclosure may be forced against the lens MOUNT CAMERAS WITH MOUNT CAMERAS WITH 2 9 AND 3 6 MM LENSES 6 8 AND 12 MM AND VARIFOCAL LENSES Pelco Manual C2408M F 403 9 SPECIFICATIONS Electrical Input Voltage 12 VDC or 24 VAC 10 Construction Aluminum base and cover Power steel camera mounting bracket Consu
3. to an adapter plate or conduit adapter two 6 32 x 1 25 inch tamper resistant screws are supplied with the adapters Use the 1 8 inch hollow screwdriver bit supplied with the Camclosure For waterproof installation a De sure the notch in the baseis pointed down Apply sealant around notch Pelco Manual C2408M F 403 5 O Adjust Camera Bees Turn on power to the camera and monitor Release one or both locking rings swivel the enclosure until the angle of the camera is correct and tighten the locking rings If you have a varifocal lens remove the cover with the supplied 1 8 inch hollow screwdriver bit Loosen the focal length and focus locking screws Adjust according to scene detail Retighten the screws Reseat the O ring on the cover and reinstall the cover CAUTION Heater elements could be hot When camera power is on use caution when adjusting the camera This applies to all models VARIFOCAL LENS o gt LOCKING SCREWS ADJUSTMENTS Color Camera Only If you have a color camera it is set up at the factory and normally requires no adjustments Sometimes however adjustments may be necessary 1 Remove the cover using the supplied 1 8 inch hollow screwdriver bit 2 Adjust the vertical phase iris level focus or switch settings refer to procedures below 3 Reseat the O ring on the cover and reinstall the cover Vertical Phase FIXED LENS 24 VAC Operation Only Adjust
4. MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video roducts One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liabi
5. PELLO Installation Operation 300 Series Camclosure Integrated Camera System C2408M F 4 03 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS 000 cece cece eee In 3 DESCRIPTION tura a bt e dd dew re an e wee RE 3 INSTALLATION uri aiit oot A ar c E ere c CE RR Ra ca 3 PREPARE WALE OR GEILING 5 15 ruht ete ae ec c ce e ce xe d 4 CONNECT VIDEO AND POWER 000 c cece RR hn 5 ATTACH BASE nihit canna secu tated edad Mgr da rs i La eU d 5 ADJUST GAMERA unto rro etre atra eec e ROGER ADORTI Gc e Re ew eco P TE d 6 ADJUSTMENTS COLOR CAMERA ONLY sssssssssse Ine 6 VERTICAL PHASE 24 VAC OPERATION ONLY ssssssssses eee 6 AUTO IRIS LEVEL ADJUSTMENT ooo 7 SWITCH SETTINGS FOR VARIFOCAL LENS 0 0 00 cece eee n 7 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS 8 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS 8 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS 9 SPECIFICATIONS Gotas ai alada 10 REGULATORY NOTICES coo A AA PO AO 10 PRODUCT WARRANTY AND RETURN INFORMATION ccc cece Rh 11 2 Pelco Manual C2408M F 4 03 IMPORTANT SAFEGUARDS AND WARNINGS 1 Read these i
6. ed camera drawings to show new design Added instructions for fixed lens with auto iris
7. eturned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco End ura and ExSite are trademarks of Pelco Copyright 2003 Pelco All rights reserved REVISION HISTORY Manual C2408M C2408M C2408M A C2408M B C2408M C C2408M D C2408M E C2408M F Date 11 99 1 00 3 00 7 00 1 01 12 01 1 03 4 03 Comments Original version Revised installation instructions Added FCC notices Added varifocal lens Changed format Viewing window redesigned changed icon Added agency logos for compliance certifications Revised heater element caution Manual revised to reflect product design revisions Revis
8. igned to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to cor rect the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 10 Pelco Manual C2408M F 4 03 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X
9. lity relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods r
10. ment is required if there is vertical roll when switching between two cameras 1 Reverse the 24 VAC connections on one camera If both cameras are connected to the same trans former this should solve the problem 2 If reversing the connections does not solve the problem or if cameras are connected to different transformers turn the adjustment screw on the power board on the back of the camera assembly on one camera while switching as rapidly as possible between the two camera views until the switching is clean and there is no vertical roll If more than two cameras are out of synchronization with each other choose one camera and synchronize all others to it VARIFOCAL LENS VERTICAL PHASE ADJUSTMENT 6 Pelco Manual C2408M F 4 03 Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris you can adjust the iris level setting to increase or decrease brightness FIXED LENS VARIFOCAL LENS IRIS LEVEL ADJUSTMENT ya AUTO IRIS LEVEL E ADJUSTMENT Switch Settings for Varifocal Lens The high resolution camera with 1 AWB Automatic white balance varifocal lens and auto iris is 2 GAM Gamma function FACTORY SETTINGS configured at the factory for a 3 AGC Automatic gain control 12345678 optimal performance in lighting 4 ESC Electronic shutter control E E E NE NE NN conditions where auto iris is 9 5 BLC Backlight compensation 0 OD O000
11. mption 13 watts or less Finish Gray polyester powder coat Video Dimensions 2 71 diameter x 7 79 L inches Connector BNC 6 88 x 19 79 cm Environment Low temperature indoor General outdoor Pan Tilt Operating Adjustment Manual 180 pan 180 tilt Temperature 50 to 122 F 46 to 50 C Rating Meets NEMA Type 3R De ices to 10 F 23 C standards Weight 1 45 lb 0 66 kg Heater Turns on at 50 F 10 C and off at 80 F 27 C Design and product specitications subject to change without notice Regulatory Notices FCC Class A monochrome EIA cameras only NOTE This equipment has been tested and found to comply with the limits of a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment gen erates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to cor rect the interference at his own expense FCC Class B color NTSC cameras only NOTE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are des
12. nder varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots ALC ELC switch Always ALC FACTORY SETTINGS o Oo a m l a YIDC switch Always DC Tama ON Auto backlight compensation BLC switch OFF E i E ABL switch ON OFF Manual backlight compensation BLC switch ON d 2 n n ABL switch OFF BB SWITCH POSITION Switch Settings for Fixed Focal Length Lens Without Auto lris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots FACTORY SETTINGS ALC ELC switch Always ELC o Oo 4 pa M a Xx mD YIDC switch Not used ON g Auto backlight compensation BLC switch OFF OFF 9 ABL switch ON 9 8 E E Manual backlight compensation BLC switch ON OUO ABL switch OFF Hl SWITCH POSITION 8 Pelco Manual C2408M F 4 03 Focus Adjustment for Fixed Focal Length Lens with Auto Iris CAUTION A Heater elements could be hot When camera power
13. nstructions Keep these instructions Heed all warnings Follow all instructions Do not block any ventilation openings Install in accordance with the manufacturer s instructions DN A c PP Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 7 Only use attachments accessories specified by the manufacturer 8 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 9 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 10 To reduce the risk of shock do not perform any servicing other that that contained on the operating instructions unless you are qualified to do so 11 Installation should be done only by qualified personnel and conform to all local codes 12 Unless the unit meets NEMA Type 3 3R 3S 4 4X 6 or 6P standards it is designed for indoor use only and must not be installed where exposed to rain and moisture 13 Use only installation methods and materials capable of supporting f
14. our times the maximum specified load 14 Use stainless steel hardware to fasten the enclosure to outdoor surfaces 15 To prevent water leakage when installing an enclosure outdoors apply sealant around the bolt holes between the enclosure and mounting surface and to the notch in the base of the enclosure DESCRIPTION The 300 Series Camclosure integrated camera system is a track light design that mounts to a wall or ceiling The system incorporates a camera and lens package into a small unobstructive medium security enclosure designed for areas subject to vandalism The system is quick and easy to install in a variety of indoor or outdoor applications It is ideal for residential office mall hospital school parking garage correction and detention and other medium security installations subject to vandalism INSTALLATION The following parts are supplied 1 Camclosure integrated camera system 2 9 pin electrical connectors 12 VDC and 24 VAC 1 Hollow screwdriver bit 1 8 inch Pelco Manual C2408M F 4 03 3 O Prepare Wall or Ceiling Prepare the wall or ceiling according to one of the options shown below WALL OR CEILING Mounting directly to wall or ceiling 4S ELECTRICAL BOX WALL OR CEILING Mounting to a 4S electrical box with 404 plaster ring 1CS300 AP ADAPTER PLATE NOT SUPPLIED L5 35x 509 SECURITY SCREW SUPPLIED WITH ADAPTER PLATE WALL OR CEILING Mounting to ICS300 COND cond
15. uit adapter not supplied WALL ORA CEILING Mounting to a two gang electrical box 1CS300 AP ADAPTER PLATE NOT SUPPLIED 6 32 X 500 SECURITY SCREW SUPPLIED WITH ADAPTER PLATE 4 Pelco Manual C2408M F 4 03 Connect Video and Power 1 Some indoor installations do not require a heater If the installation does not require a heater disconnect the heater wiring a Remove the cover with the supplied 1 8 inch hollow screwdriver bit b Remove the camera from the mounting bracket and unplug the four pin heater connector in the base The connector has orange red and black wires c Reinstall the camera d Reseat the O ring on the cover and reinstall the cover 2 Depending on the input voltage wire either the 12 VDC or 24 VAC connector supplied to the input power wires Plug the connector into the mating connector in the base 3 Connect the video cable the proper hole of the mounting bracket If the camera is not installed in the correct WARNING To prevent damage to the camera or lens the camera must be installed in hole the window of the enclosure may be forced against the lens MOUNT CAMERAS WITH MOUNT CAMERAS WITH 2 9 AND 3 6 MM LENSES 6 8 AND 12 MM AND VARIFOCAL LENSES Attach Base LOCKING RING Release the base locking ring for access to the mounting holes Mounting hardware is not supplied if you attach the base directly to a wall or ceiling To attach the base
Download Pdf Manuals
Related Search