Peerless Industries 16D User's Manual
Contents
1. gY i fig 2 4 fig 2 3 Boara landscape 8 of 9 ISSUED 08 02 05 SHEET 202 9010 1 Mounting and Removing Flat Panel Screen Note Security screw may need to be loosened to avoid interference with wall plate Hook interface bracket BB onto wall plate AA Then slowly swing screen in as shown Turn security screw using security allen wrench FF clockwise at least six times to prevent screen from being removed as shown in detail 1 Screen can be adjusted horizontally if desired Note To lock the screen down tighten security screw to wall plate using security allen wrench as shown in detail 1 To remove screen from mount loosen security screw swing screen away from mount and lift screen off of mount e Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television DETAIL 1 t sgl 9 of 9 ISSUED 08 02 05 SHEET 202 9010 1 2005 Peerless Industries Inc All rights reserved SmartMountis a trademark and Peerless is a registered trademark of Peerless Industries Inc Allother brand and product names are trademarks or registered trademarks of their respective owners2. 2 5 64 mm Insert anchors DD in holes flush with DD wall as shown right Place wall plate over anchors and secure with 14 x 2 5 screws CC Level then tighten all fasteners Tighten screws so that wall plate is firmly attached but do not overtighten Overtightening can damage screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Always attach concrete expansion anchors directly to load bearing concrete Never attach concrete expansion anchors to concrete covered with plaster drywall or other finishing mate rial If mounting to concrete surfaces covered with a finishing surface is unavoidable the finishing surface must be counterbored as shown below Be sure concrete anchors do not pull away from concrete when tightening screws If plaster drywall is thicker than 5 8 custom fasteners must be supplied by installer UZ A ae LE Oq INCORRECT CORRECT concrete ua O o MANNY AONA F drywall ee drywall CUTAWAY VIEW 6 of 9 ISSUED 08 02 05 SHEET 202 9010 1 Installing Interface Bracket to PLP Adapter Plate To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Place screen face side down Attach the interface bracket BB to the PLP adapter plate sold separately
3. for other types of mounting situations CS center of screen rt Sy E i a ey a 64 a gt L_e 1S lIe 9 ISO O aMSOS SaMO j ijy D CoO CD fig 1 1 fig 1 2 4of9 ISSUED 08 02 05 SHEET 202 9010 1 Installation to Double Wood Stud Wall e Installer must verify that the supporting surface will safely support the combined weight of all attached equipment and hardware Wall plate AA can be mounted to two studs that are 16 apart Use a stud finder to locate the edges of the studs Use of an edge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center Place wall plate on wall as a template The top mounting slots should be 2 5 above the desired screen center as shown in figure 1 3 Level plate and mark the center of the four mounting holes Make sure that the mounting holes are on the stud centerlines Drill four 5 32 4 mm dia holes 2 1 2 65 mm deep Make sure that the wall plate is level secure it using four 14 x 2 5 wood screws CC as shown in figure 1 4 Skip to step 2 on page 7 Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in Ib 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly rec
4. anchor 590 0097 EE M10 x 1 5 x 15mm socket head screw 520 9262 FF 4mm security allen wrench 560 1146 3 0f 9 ISSUED 08 02 05 SHEET 202 9010 1 Installation to Single Wood Stud Wall e Installer must verify that the supporting surface will safely support the combined weight of all attached equipment and hardware Use a stud finder to locate the edges of the stud Use of an edge to edge stud finder is highly recommended Based on its edges draw a vertical line down the stud s center Place wall plate AA on wall as a template making sure that the three mounting holes are over the stud centerline The top mounting hole should be 2 5 above the desired screen center as shown in figure 1 1 Level plate and mark the center of the three holes Drill three 5 32 4 mm dia holes 2 1 2 65 mm deep Make sure that the wall plate is level secure it using three 14 x 2 5 wood screws CC as shown in figure 1 2 Skip to step 2 on page 7 Tighten wood screws so that wall plate is firmly attached but do not overtighten Overtightening can damage the screws greatly reducing their holding power Never tighten in excess of 80 in lb 9 N M Make sure that mounting screws are anchored into the center of the stud The use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Installers are responsible to provide hardware
5. ommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs Install ers are responsible to provide hardware for other types of mounting situations CS center of screen CL C O Oe ISOS aoo S aMSOSOS j ijy fig 1 4 5 of 9 ISSUED 08 02 05 SHEET 202 9010 1 Installation to Solid Concrete or Cinder Block e When installing Peerless wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block Cinder block must meet ASTM C 90 specifica tions It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity Concrete must be 2000 psi density minimum Lighter density concrete may not hold concrete anchor e Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components template to mark four mounting holes The top ley Make sure that wall plate AA is level use itas a mounting hole should be 2 5 above the desired screen center as shown in figure 1 1 on page 4 Drill four 1 4 6 mm dia holes to a minimum depth of
6. peer less Solid Solutions Solid Support Installation and Assembly Smart Mount Dedicated Flat Wall Mount for Flat Panel Screens Models SF 16D Features e Ultra slim design holds the screen flat against the wall e Integrated security features provide effective theft deterrence Max Load Capacity 200 Ib 90 7 kg 3215 W North Ave Melrose Park IL 60160 800 729 0307 or 708 865 8870 Fax 708 865 2941 www peerlessmounts com ISSUED 08 02 05 SHEET 202 9010 1 Note Read entire instruction sheet before you start installation and assembly Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings please call Peerless customer care at 1 800 729 0307 This product should only be installed by a qualified professional Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard ware and components Never exceed the Maximum Load Capacity of 200 Ib 90 7 kg If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do no
7. t overtighten Overtightening can damage the items greatly reducing their holding power Tools Needed for Assembly stud finder edge to edge stud finder is recommended drill 1 4 bit for concrete and cinder block wall 1 2 bit for metal stud wall 5 32 bit for metal or wood stud wall 3 8 socket wrench socket with extended driver recommended level 6mmallen wrench Accessories Metal Stud Fastener Kit ACC 415 Table of Contents PS ASE AAE AEE E E AEE ETE AAE AE I A A E A E E EE 3 l stall tionto Single Wood Stud Wallerian ee ee ee i Re ee 4 Installation to Double Wood Stud Wall sic tne ile ee WE ee ee 5 Installation to Solid Concrete or Cinder BlOCK niinen aa anaa anaa E EER Ea E ART 6 Installing Interface Bracket to PLP Adapter Plate 0 0 ccccccceeeseeeeeeceeeceeceeeeeeeeeeeeaaeeeeaaaeeeeceeeeseaaeeseaeeeeeeeeeessaaeeseneeeeeeneees 7 Installing Interface Bracket to LC Adapter Plate c ccceccceeeeeeeeeeeenaeeeeeaeeeeeeeeeeeeaaaeeecaaaeeeeceeeeeeseeeesecaeeseseeeeeesiaaeesenieeeseeaaees 8 Installing Flat Panel Screen to Wall Plate ceccccccseeececeeeeeeeeeeeeeeaaeeeeeaaeeeeaeeeeceaaaeeeaaaaeseaaaeeseseaaeesaaaeeeegeeeeessaaeesseeeesenaeees 9 For customer care call 800 729 0307 or 708 865 8870 20f 9 ISSUED 08 02 05 SHEET 202 9010 1 Parts List Description Qty Part AA wall plate 200 1797 BB interface plate 200 0860 CC 14 x 2 5 wood screw 5S 1 015 C03 DD Alligator
8. using four M10 x 15 mm socket head screws EE as shown in figures 2 1 portrait or 2 2 landscape Tighten screws so adapter brackets are firmly attached Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become detached Tighten to 40 in lb 4 5 N M maximum torque GENERIC PLP ADAPTER PLATE GENERIC PLP B B ADAPTER PLATE fig 2 2 paren landscape 7 of 9 ISSUED 08 02 05 SHEET 202 9010 1 Installing Interface Bracket to LC Adapter Plate To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Place screen face side down Attach the interface bracket BB to the LC adapter plate sold separately using four M5 screws provided with plate as shown in figures 2 3 portrait or 2 4 landscape Tighten screws so adapter brackets are firmly attached Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become detached Tighten to 40 in lb 4 5 N M maximum torque GENERIC LC GENERIC LC ADAPTER PLATE ADAPTER PLATE BB x M5 SCREWS a A M5 SCREWS
Download Pdf Manuals
Related Search