Peavey XRD 680S User's Manual
Contents
1. sulated dangerous voltage within product s enclosure of electric shock to persons Intended to alert the user of the presence of imporiant operating and maintenance servicing instructions in the literature accompanying the product Intended to alert the user to the presence of un that may be of sufficient magnitude to constitute a ri isk of electrical shock DO NOT To reduce the risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel WARNING To prevent electrical shock or fire hazard do not expose this appliance to rain or moisture Before using this appliance read the operating guide for further warnings WARNING For optimum performance and reliability DO NOT PRESENT EACH either of the two AMPLIFIER WITH A SPEAKER LOAD OF LESS THAN 4 OHMS OR A COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS THAN 4 OHM Using one speaker it must be rated at 4 ohms minimum Using two speakers they must be rated each at 8 ohms minimum Thank you for purchasing the Peavey XRD 6805 mixer with built in stereo digital effects and stereo amplifiers This is a powerful easy to use portable eight channel mixing con sole Your XRD 6808 features a rugged heavy gauge cold rolled steel and aluminum chassis finished in oven cured epoxy for toughness and screen printed utilizing the latest photo graphic film and U V cured2. SPEAKER alo XRD 6808 external EQ amp internal power amp for mains mono Internal EQ amp power amp for monitors XRD 6808 gt Lux jo ra Master Graphic Equalization THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY Ces clauses de garantie ne sont vaiables qu aux Etats Unis et au Canada Dans tour les autres pays les clauses de garantie et de maintenance sont fixees par le distributeur national et assuree par lul selon legislation envigueur Diese Garantie ist nur in den USA and Kanada gultig Alle Export Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen Esta garantia es valida solamente cuando el producto es comprado en E U continentales o en Canada Todos los productos que sean comprados en el extranjero estan sujetos a las garantias y servicio que distribuidor autorizado determine y ofrezca en los diferentes paises PEAVEY ONE YEAR LIMITED WARRANTY REMEDY PEAVEY ELECTRONICS CORPORATION PEAVEY warrants his product EXCEPT covers footsvitches paichcords tubes and meters to be free trom detecte in material and workman
3. 0 dBu 778 Volts RMS All specs are referenced to nominal output le 0 dBY unless otherwise noted measurements are wideband 20 Hz to 20kHz unless otherwise stated All control settings are nominal 50 rotation unless otherwise noted CHANNEL Equivalent Input Noise 114 5 dBV 40 dB max gain Frequency Responsi to speaker outputs 1 dB 10 Hz to 23 000 Hz Distortion 1 kH2 Less than 015 Input Impedan Low Z Bal 1 7 kilohms Line Input 13 kilohms High EQ 15 dB 10 kHz minimum center detent flat 2 dB Mid EQ 15 dB 600 Hz minimum Center detent flat 2 dB Low EQ 15 dB 50 Hz minimum Center detent flat 2 dB Nominal Channel Gain LowZ 20dB Line 0dB Minimum Channel Gain LowZ 69dB Line 89dB Maximum Channel Gain LowZ 40dB Line 20dB Nominal Input Level Z 20dBV Line Minimum Input Level Low Z 40dBV Line 204 Maximum Input Level Low Z 46dB Line 26dB Phantom Power 48 DC GRAPHIC EQUALIZER Filter Bandwidth 1 octave Filter Frequencies ISO Stds 63 Hz 125 Hz 250 Hz 1 kHz 2 kHz 4 kHz 8 kHz 16 Hz Filter Q 157 Maximum Boost amp Cut Noise 102 dBV Distortion IKHz Less than 005 Frequency Response 1 dB 7 Hz to 40 kHz Input Level OdBV 1 0 V RMS Max 19 dBV 9 V RMS Output Level Nom OdBV 1 0 V RMS Max 19
4. GR our po m FX RETURN TARE AU ne LTAPE OUT g e ec ee L TREN o Soo 00606 BALANCED LOW IMPEDANCE INPUT 1 For use with low impedance microphones or low level sources equipped with an XLR connector LINE INPUT For use with line level signal or compatible high Z microphones equipped with a 1 4 phone plug NOTE It is possible to use both the mic and line inputs on a single channel simultaneously It is however unlikely that the gain matching of the mic and line will allow this hookup to be useful This practice is not recommended LEVEL 3 Controls the channel output level Maximum output level is obtained by rotating this control fully clockwise Minimum output level is obtained by rotating this control fully counterclockwise PAN 4 Provides an individual channel pan L to R fa lity Center position delivers equal L amp R stereo image balance MONITOR 5 Controls the channel monitor mix level This is independent of all other channel controls Maximum channel monitor mix level is obtained by rotating this control fully clockwise Minimum channel monitor mix level is obtained by rotating this control fully counterclockwise LOW EQ 6 Controls the channel low EQ level An active tone control shelving type 15 dB that varies the low frequency range Maximum low EQ boost is obtained by rotating this control fully clockwise Maximum low EQ cut is o
5. ink technology for razor sharp hard wearing control and calibration graphics Every on board component has been carefully chosen to deliver the highest possible perfor mance Precision professional reliability and minimal operating noise characteristics are only the initial criteria used during the process of selecting the components that ensure that your XRD 6805 becomes an indispensable addition to your live performance equipment All printed circuit boards are constructed from rugged U S military spec material using the latest automated assembly technology wave solder and computer controlled all faults analyzed and corrected Q A procedures Each channel features front panel output and monitor level controls as well as high mid low equalization and effects emphasis controls Every input channel has a studio quality low impedance XLR type input microphone input as well as a 1 4 line input Switchable 48 V phantom power is provided The unit features stereo 150 watt power amplifiers une DIGITAL EFFECTS MADE IN U S A 1 Ta 8 e o popa pa pa ss fel MALL ROOM REVERE MEDIUM ROOM REVERE LARGE ROOM REVERS X LARGE ROOM REVERE GATED REVERS DELAYS ECHOS MULT EFFEC e gt XRD 6805 ovreurs PHANTOM GRAPHIC
6. should fail IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PRE VENT VOIDING THE WARRANTY If the amp repeatedly blows fuses it should be taken to a qualified service center for repair LD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNEC TED ROM ITS POWER SOURCE SWITCH 34 Center position is OFF Two ON positions are provided one of which will properly ground the amplifier Switch to the ON side that yields the lowest amount of residual hum or popping noise when the instrument is touched 220 and 240 volt models have a two way On Off switch only LINE CORD 120 V PRODUCTS ONLY 35 For your safety we have incorporated a 3 wire line mains cable with proper grounding facilities It is not advisable to remove the ground pin under any circumstances If it is necessary to use the equipment without proper grounding facilities suitable grounding adaptors should be used Less noise and greatly reduced shock hazard exist when the unit is operated with the proper grounded receptacles EXTERNAL SPEAKER JACKS 36 Provided for connection of external speaker cabinets Minimum total impedance is 4 ohms for each amplifier LINE MAINS CORD RETAINERS 37 Allow storage of mains cable for travel NOTE The line cord should be removed from the cord retainers before use SPECIFICATIONS NOTE specifications are typical unless otherwise noted dBV 1 Volt RMS
7. ECTOR control determines which particular digital bank is selected for use As will be seen from the front panel illustration digital effect banks are available from small room reverbs through extra large rooms gated reverbs delays echos and multi effects Rotating the EFFECT SELECTOR control deter mines which particular stereo digital effect is drawn from whichever bank has been selected by means of the BANK SELECTOR switch NOTE Refer to the chart printed on the faceplate and select one of the 128 effects using the BANK and SE LECT switches There are 16 effects settings for each BANK Use the BANK switch to choose the type of effect and the SELECT switch to choose which variation of this effect to use STEREO 9 BAND GRAPHIC EQ 12 Provides 12 dB equalization at each center frequency EQ boost is obtained by moving a particular EQ band s slide control above the center line EQ cut is obtained by moving a particular EQ band s slide control below the center line OPERATION NOTE This equalizer is designed to provide room equalization feedback control and system tone control No amount of equalization will correct the response curve of a poor loudspeaker Always begin with all sliders in the 0 position and avoid excessively cutting large segments of the audio passband which would limit the system s dynamic range MASTER GAIN 13 Controls the overall volume level of the main system The signal from this control is available at the
8. ROVIDED HOWEVER THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESSED LIMITED WARRANTIES AS HEREINABOVE STATED HAVE BEEN COMPLIED WITH IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE YEAR OR NINETY DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THESE LIMITED WARRANTIES ARE THE ONLY EXPRESSED WARRANTIES ON THIS PRODUCT AND NO OTHER STATEMENT REPRESENTATION WARRANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY Inthe event of any modification or disclaimer of expressed or implied warranties cr any limitation of remedies contained herein conflicts with applicable law then such modification cisciaimar or limitation as the may be shall be deemed to be modified to the extent necessary to comply with such law Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to equipment purchased in the United States of America INSTRUCTIONS WARRANTY REGISTRATION CARD 1 Mail the completed WARRANTY REGISTRATION CARD to PEAVEY ELEC
9. S into 4 ohms each channel both channels driven 113 watts RMS into 8 ohms cach channel both channels driven 225 waits RMS into 4 ohms one channel driven 130 watts RMS into 8 ohms one channel driven Intermodulation Distortion Less than 0 1 10 mW to rated power 250 Hz amp 7 kHz 4 ohms Total Harmonic Distortion Less than 0 1 DDT Dynamic Range Greater than 26 dB DDT Maximum Distortion Below 0 5 THD for 6 dB overload Below 1 THD for 20 dB overload Hum amp Noise 92 dB below 150 watts Slew Raie 15 V uSec 1 V RMS For 150 watts 4 ohms Input Impedance 19 kilohms Power Requirements 800 watts 120 V AC 60 Hz XRD 6808 LEVEL CHART XRD 680S internal EQ and power amp for mains External EQ and power amp for monitors XRD 680s e eo XRD 6805 internal EQ amp external y ponar amas ar mains ere MONITORS EQs amp internal power amp for monitors TAPE RECORDER XRD 6805 external EQs amp power amps for mains Internal EQ amp power amps for monitors XRD 6805 internal EQ amp power amp for mains mono External EQ amp internal power amp for monitors e
10. TRONICS CORPORATION POST OFFICE BOX 2808 MERIDIAN MISSISSIPPI 39302 2895 Keep the PROOF OF PURCHASE In the event warranty service is roquired during the warranty poriod you will need this document There will be no identification card issued by Peavey Electronics Corporation 2 IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESSES Completion and mailing ot WARRANTY REGISTRATION CARDS Should notification become necessary for any condition that may require correction Tho REGISTRATION wil ensure that you are contacted and property notified b Notice of address changes If you move from the address shown on the WARRANTY REGISTRATION CARD you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of information or correction 3 You may contact Peavey direclly by telephoning 601 489 5305 IMPORTANT SAFETY INSTRUCTIONS WARNING When using electric products basic cautions should always be followed including the following 1 safety and operating instructions before using this product 2 All safety and operating instructions should be retained for future reference 2 Obey all cautions in the operating instructions and on the back of the unit structions should be followed 4 All operating 5 This product sh
11. as fallen or been spilled into the unit v The unit does not operate correctly d The unit hay been dropped or the ei 16 The user should not attempt to service this equipment All service work should be done b arts can be cleaned with a damp rug The vinyl covering used on some units can be cleaned with damp rag or an ammonia from power supply before cleaning losure damaged jualified service technician 17 This product should be used only with a cart or stand that is recommended by Peavey Electronics 18 Exposure to extremely high noise levels may cause a permanent hearing loss Individuals vary considerably in susceptibility to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently Intense noise for a su The U S Government s Occupational Safety and Health Administration OSHA has specified the following permissible noise level exposures Duration Per Day In Hours Sound Level JBA Slow Response 8 90 6 92 4 95 3 97 2 100 102 1 105 12 110 114 oF Tess 15 According to OSHA any exposure in excess of the above permissible limits could result in some hearing loss Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to preven permanent hearing loss if exposure is in excess of the limits as set forth above To ensure against potentially dangerous exposure to high sound pressure le
12. btained by rotating this control fully counterclockwise MID EQ 7 Controls the channel mid EQ level An active tone control peak notch that adjusts the mid frequency range Maximum mid EQ boost is obtained by rotating this control fully clockwise Maximum mid EQ cut is obtained by rotating this control fully counterclockwise HIGH EQ 8 Controls the channel high EQ level An active tone control shelving type 15 dB that varies the high fre quency range Maximum high EQ boost is obtained by rotating this control fully clockwise cut is obtained by rotating this control fully clockwise EFFECTS SEND 9 Controls the channel effects drive level Maximum effects signal is obtained by rotating the control fully clock wise Minimum signal level is obtained by rotating this control fully counterclockwise MASTER SECT EFFECT LED 10 When blinking this LED indicates that the effects system is within 6 dB of clipping when fully illuminated indicates that the effects system s sound will be distorted as clipping will be taking place If the EFFECT LED becomes fully illuminated use the EFFECTS MASTER control 15 to reduce the effects system operating level so the EFFECT LED is no longer illuminated or only blinks occasionally A decrease in the effects level in the main mix can be compensated for by inereasing the gain of the EFFECTS RETURN 16 EFFECT SELECTOR AND BANK SELECTOR 11 Rotating thc BANK SEL
13. dBV 9 V RMS Input Impedance 10 kilohms Output Impedance 100 ohms 20dB 1548 Monitor 15 dB 15 dB Tape Effects Maximum Output Level Main 18 dBV 8 0 V RMS Monitor 18 dBV 8 0 Y RMS Tape 18dBV 8 0 V RMS Effects 18 dBV 8 0 V RMS Nominal Headroom Main 18 dB Monitor 18 dB 18 dB Effects 18 dB Output Impedance Main 100 ohms Monitor 100 ohms Tape 10k ohms Effects 100 ohms Output Noi Residual 101 dBV Master Levcl Down Bus 94 dBV Master Nominal All Channel Levels Full CCW Effects Returns Down Nominal 86 dBV All Controls Nominal Low Z Input Terminated 150 Ohms Aux Input Impedance 120 kilohms Aux Input Level Nom 0dBV 47 dBV Min 1 Tape Input Level Nom 44dBV Max 11 dBV Min 10dBV DIGITAL EFFECTS PROCESSOR Reverberation Settings 32 reverb positions 1 bypass setting 13 warm reverbs 13 bright reverbs 2 gated reverbs 2 reverse reverbs Frequency Response 20 Hz to 11 kHz Quantization 16 Bit Linear PCM Signal To Noise R 95 dB Minimum Headroom 648 Limit LED Illumination POWER AMP SECTION 300 SC Module with DDT Frequency Response 0 1 dB 10 Hz to 40 kHz Rated Power Rated Power 150 watts RMS into 4 ohms both channels driven 100 watts RMS into 8 ohms both channels driven Power 8 Clipping 1 THD 1 kHz 120 VAC line typical 160 waits RM
14. er This is a TRS ti A stereo 14 plug inserted here will have the Left signal on the Tip and the Right signal on the Ring Do not use mono plug on this output unless a mono plug is also plugged into the Graphic Input 22 ring sleeve jack FOOTSWITCH 24 This 1 4 jack provides access for connection of a footswitch optional and is used to activate defeat digital effects AUXILIARY INPUTS 25 These 1 ks provide inputs to the Left and Right Main mixing buses and the Monitor mixing bus for patch ing returns from external effects devices extra mixing channe If the auxiliary signal is mono plug a mono 1 4 plug into the L MONO jack If the auxiliary signal is stereo plug the Left signal into the L MONO jack and the Right signal into the R jack POWER AMP INPUTS 26 These 1 4 jacks provide access to connect external line level signals to the Left and Right power amplifiers OPERATION NOTE These jacks permit the two internal power amplifiers to be switched away from their level signals normal inputs and to accept external line TAPE SECTION TAPE OUT STEREO LEVEL 27 Controls the signal level at the tape out jacks 31 Operation is independent of the main master level control 13 and the graphic equalizer 12 TAPE AUX IN LEVEL 28 When external signals are patched into the tape in jacks 30 or the auxiliary inputs 25 TAPE AUX IN LEVEL 28 provides control over the level of signals sent from these
15. ers footswiches patchcords tubes or meters repair the defect In material or workmanship or replace the product at Peavey s option and provided however that n any case all costs of shipping if necessary are paid by you the purchaser THE WARRANTY REGISTRATION CARD SHOULD EE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN 14 DAYS FROM THE DATE OF YOUR PURCHASE In order to obtain service under these warranties you must Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product Ifthe DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will bo to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such servico OR b Ship tho detective prapald to PEAVEY ELECTRONICS CORPORATION Intemational Service Center 325 Hwy 13 amp BO East MERIDIAN MS 39301 including therewith a complete detailed description of the problem together with legible copy of he original PROOF OF PURCHASE and a complete return address Upon Peavey s receipt of these items defect 5 remedial under these limited warranties and the other terms and conditions expressed herein have been complied with Peavey will provide the necessary warranty ser
16. his switch selects phantom power ON or OFF for all channels Phantom power is on when the switch is in the down position and off when the switch is in the up position MASTER OUTPUTANPUT SECTION MAIN OUTPUT 19 These 1 4 jacks provide a stereo signal from the mai to feed an auxiliary amplifier speaker system See wiring diagram vstem mix before the graphic equalizer Used primarily MONITOR OUTPUT 20 This 1 4 jack provides a signal from the MONITOR mix for an external monitor amplifier speaker system The level is determined by the channel monitor and master monitor controls EFX OUTPUT 21 This 1 4 jack provides signal from the EEX mix for external effects or signal processing equipment GRAPHIC INPUT 22 This 1 4 jack provides an input to the internal graphic equalizer power amp This is a TRS tip ring sleeve switching jack and a signal inserted here interrupts the normal signal path from the main bus into the equalizer OPERATION NOTE This jack permits the equalizer to be switched away from its normal input and accept an external signal to be equalized If a stereo signal is to be equalized the Left signal should be connected to the Tip and the Right signal should be connected to the Ring of a stereo 1 4 plug If a mono 1 4 plug is used signal will only go to the Left graphic The Right graphic will get no signal GRAPHIC OUT 23 This 1 4 jack provides access to the output of the internal graphic equaliz
17. inputs to the main Lefi and Right mixes Maxi mum TAPE AUX to main mix signal level is obtained by rotating this control fully clockwise Minimum TAPE AUX to main mix signal level is obtained by rotating this control fully counterclockwise NOTE It is possible to use both the Aux and Tape inputs simultaneously It is however unlikely that the gain matching of the Aux and Tape will allow this hookup to be useful This practice is not recommended TAPE AUX TO MON 29 Allows the TAPE AUX to be assigned to the monitor TAPE OUT TAPE IN CAUTION Before placing connected tape decks in the record mode set the TAPE AUX IN level control to 0 or off Most tape decks feed the input signal directly to the ouput when in record mode This creates a closed loop condition from the tape out to tape in jack which can affect the operational level or sonic quality of the system TAPE IN JACKS 30 These two jacks provide an input for stereo tape decks CD players etc TAPE OUT JACKS 31 These two jacks provide left and right main outputs to the left and right inputs of a stereo tape deck Output level is determined by the TAPE OUT 27 level control POWER INDICATOR PILOT LIGHT LED 32 Tlluminates when AC power is being supplied to the amp IE L5 m A C POWER AND POWER AMPLIFIER OUTPUT FUSE 33 The fuse is located within the cap of the fuseholder If the fuse
18. main output 19 Under normal conditions this signal is also internally patched through the graphic EQ and power amplifiers so that this control sets the volume of the speakers connected to the external speaker jacks 36 Maximum master signal level is obtained by rotating this control fully clockwise Minimum master signal level is obtained by rotating this control fully counterclockwise MASTER MONITOR 14 Controls the overall monitor mix level Maximum monitor signal level is obtained by rotating this control fully clockwise Minimum monitor signal level is obtained by rotating this control fully counterclockwise EFFECTS MASTER 15 Controls the effects level supplied to the internal effects and the effects out jack Maximum effects signal level is obtained by rotating this control fully clockwise Minimum effects signal level is obtained by rotating this control fully counterclockwise EFX RETURN 16 Controls the level of the stereo EFX in the main system mix Maximum effects return signal level is obtained by rotating the control fully clockwise Minimum effects return signal level is obtained by rotating this control fully counterclockwise EFX TO MONITOR 17 Controls the level of the EFX in the monitor system Maximum monitor effc rotating this control fully clockwise Minimum monitor effects signal level fully counterclockwise signal level is obtained by obtained by rotating this control PHANTOM POWER ON OFF 18 T
19. ould not be used near water i e bathtub sink swimming pool wet basement etc 6 This product should be located so that its position does not interfere with its proper ventilation It should not be placed flat against a wall or placed in a built in enclosure that will impede the flow of cooling air 7 This product should not be placed near source of heat such as a stove radiator or another heat producing amplifier 8 Connect only to power supply of the type marked on the unit adjacent to the power supply cord formation on grounding write for our free booklet Shock 9 Never break off the ground pin on the power supply cord For mor Hazard and Grounding 10 Power supply cords should always be handled carefully Never walk or place equipment on power supply cords Periodically check cords for cuts or signs of stress especially at the plug and the point where the cord exits the unit 11 The power supply cord should be unplugged when the unit is to be unused tor long periods of time 12 product is to be mounted in an equipment rack rear support should be provided 13 based household cleaner if necessary Disconnect un 14 Care should be taken so that objects no fall and liquids are not spilled into tbe unit through the ventilation holes or any other openings 15 This unit should be checked by a qualified service technician if The power supply cord or plug has been damaged b Anything h
20. ship for a period of ono 1 year from dato of purchase PROVIDED howovor ina this limited warranty is extended only to the original totail purchaser and is eubjact to the conditions exclusions an limitations horeinafter set forth PEAVEY 90 DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters Peavey warrants the tubes or meters contained in the product to be free from detects in material and workmanship for e period of ninety 80 days date of purchase PROVIDED however thet this limited warranty is extended only to the original retail purchaser and is also subject to conditions exclusions and limitations hereinafter set forth CONDITIONS EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect i The first purchase of the product is for the purpose of resale or b The original retail purchase is made from an AUTHORIZED PEAVEY DEALER or The product has been damaged by accident or unreasonable use neglect improper service or maintenance other causes not arising out of defect in material or workmanship or d The numbor affixed to the product is aliered defaced or removed In the event of a defect in material and or workmanship covered by this limited warranty Poavoy wil In tho case of tubes or motore replace tho dafsctive component without charge b In other covered cases cases invoking anything other than cov
21. vels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such this amplification system be protected by hearing protectors while this unit is in operation SAVE THESE INSTRUCTIONS ER I A Peavey Electronics Corporation 711 A Street Meridian MS 39301 U S A 601 483 5365 Fax 486 1278 1993 590302043 Printed in U S A 2 96
22. vice to repair or replace the product and will return il FREIGHT COLLECT to you the purchaser Peavey s liability to the purchaser for damages from any cause whatsoever and regardless of the torm of action including negligenco is limited to the actual damages up to the greater of 500 00 or an amount equal to the purchase price of tho product that caused the damage or tat i the subject of or is directly related to the cause of action Such purchase price will bo that in effect for the specif product when the cause of action arose This limitation of liability will not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey s negligence Peavey does not assume lability for personal injury or property damage arising out of or caused by non Paavey alteration or attachment nor does Peavey assume respanabilty for damage to interconnected non Peavey equipment that may result from tne normal functioning and maintenance of the Peavey equipment UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS LOST SAVINGS ANY INCIDENTAL DAMAGES OR ANY CONSEQUEN TIAL DAMAGES ARISING CUT OF THE USE OR INABILITY TO USE THE PRODUCT EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED CR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE P
Download Pdf Manuals
Related Search