Peavey Blues Classic User's Manual
Contents
1. or or until the noise is minimized NOTE Should the noise problem continue consult your Authorized Peavey Dealer the Peavey Factory or a qualified service technician THE GROUND SWITCH IS NOT FUNCTIONAL ON 220 240 VOLT MODELS SPEAKER OUTPUTS 16 Speaker output 4 jacks are provided for 16 and 8 ohms When both jacks are engaged amplifier impedance is 8 ohms REMOTE SWITCH JACK 17 Provided for the connection of the optional remote footswitch Footswitch is used to select the Lead or Nor mal channels and defeat reverb When using remote footswitch always insert the plug fully second click to ensure proper operation EFFECTS RETURN 18 Input for returning signals from external effects or signal processing equipment EFFECTS SEND 19 Output for supplying signals to external effects or signal processing equipment BLOCK DIAGRAM rie vom re Es A Te This block diagram shows signal flow within the unit In order to thoroughly understand the units functions please study the diagram carefully SPECIFICATIONS POWER AMPLIFIER SECTION 4 OBQS EL84 s with 12AX7 driver Rated Power amp Load 50 W RMS into 16 or 8 ohms Power Clipping Typically 5 THD 1 kHz 120 V AC line 50 W RMS into 16 or 8 ohms Bias must be reduced to measure Frequency Response 0 2 dB 50 Hz to 15 kHz2. BLUE SIN GLE UNIT WITH EFFECFS EO OPERATING G AA EU wi Kan Ra At AAA Intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons Intended to alert the user to the presence of important operating and maintenance servicing instruc tions in the literature accompanying the product CAUTION Risks of electrical shock DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover No user serviceable parts inside Refer Servicing to qualified service personnel WARNING To prevent electrical shock or fire hazard do not expose this appliance to rain or moisture Before using this appliance read the operating guide for further warnings Este s mbolo tiene el prop sito de alertar al usuario de la presencia de instrucciones importantes sobre la operaci n y mantenimiento en la literatura que viene con el producto Este s mbolo tiene el prop sito de alertar al usuario de la presencia de voltaje peligroso que no tiene aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir riesgo de corrientazo PRECAUCION Riesgo de corrientazo No abra PRECAUCION Para disminu r el riesgo de corrientazo no abra la cubierta No hay piezas adentro que el usuario pueda reparar Deje todo mantenimiento
3. MASTER VOLUME 6 Regler fiir die Gesamtlautst rke des Systems TREBLE MIDDLE AND BASS EQ 7 Passive Klangregler die jeweils die H hen Mitten und B sse bearbeiten REVERB 8 Eingebautes Echo Hall System In Uhrzeigerrichtung drehen um den Effekt zu verst rken Fernbedienungs Fu schalter zum Ein und Ausschalten des Effekts POST GAIN 9 Kontrolliert den gesamten Lautst rke pegel des Hauptkanals Mastervolumen Die endg ltige Lautst rkeregelung sollte vorgenommen werden nachdem der gew nschte Sound eingestellt ist PRE GAIN 10 Kontrolliert den Vorstufenpegel des Lead Kanals NORMAL GAIN ID Regelt den Pegel des Normal Kanals BRIGHT INPUT 12 Dieser Instrumenten Eingang erh ht die Wiedergabe der hohen Frequenzen hnlich wie ein Bright Schalter im Vergleich zum Normal Eingang NORMAL INPUT 13 Eingang f r Signale mit Instrumentenpegel F r brillantere Frequenzwiedergabe in den H hen siche Bright Input No 12 FUSE 14 Die Sicherung befindet sich innerhalb der Kappe des Sicherungshalters Wenn die Sicherung durchbrennt MUSS SIE DURCH EINE DES GLEICHEN TYPS UND MIT DEM GLEICHEN WERT ERSETZT WERDEN UM DAS GER T ZU SCH TZEN UND DIE GARANTIELEISTUNGEN ZU ERHALTEN Wenn am Verst rker wiederholt die Sicherung durchbrennt mu das Ger t in eine qualifizierte Fachwerkstatt WARNUNG SICHERUNGSWECHSEL NUR BEI ABGEZOGENEM NETZKABEL VORNEHMEN LAUTSPRECHERAUSGANGE 15 F r die L
4. REVERB 8 Reverberation is an echo effect Rotate clockwise to increase the effect Remote footswitch can control On Off POST GAIN 9 Controls the overall volume level of the Lead channel The final level adjustment should be made after the desired sound has been achieved PRE GAIN 10 Controls the input volume level of the Lead channel NORMAL GAIN 11 Controls the volume level of the Normal channel BRIGHT INPUT 12 Input for instrument level signals This input produces enhanced high frequency response treble similar to a bright switch when compared to the normal input NORMAL INPUT 13 Input for instrument level signals For brighter frequency response highs see Bright Input No 12 FUSE 14 The fuse is located within the cap of the fuseholder If the fuse should fail IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PRE VENT VOIDING THE WARRANTY If the amp repeatedly blows fuses it should be taken to a qualified service center for repair WARNING THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE GROUND SWITCH 15 Three position rocker type switch which in most applications should be operated in its center or zero posi tion There may be some situations when audible hum and or noise will come from the loudspeaker If this situation arises position the ground switch to either positive or negative
5. MASTER VOLUME Volumen de maestra 6 Controla el nivel global de volumen del sistema TREBLE MIDDLE AND BASS EQ Ecualizador de tiples medias y agudas 7 Controles de tono pasivo que regulan las frecuencias altas medias y agudas respectivamente REVERB Reverberaci n 8 La reverberaci n es un efecto de eco Haga girar a la derecha para aumentar el efecto El encendido apagado on off se puede controlar con el pedal interruptor de control remoto POST GAIN Control de ganancia posterior del preamplificador 9 Controla el volumen general del canal solista El ajuste final de nivel debe hacerse despu s de que se haya obtenido el sonido deseado PRE GAIN Control del preamplificador 10 Controla la entrada de volumen del canal solista NORMAL GAIN Ganancia normal 11 Controla el nivel de volumen del canal Normal BRIGHT INPUT Entrada de brillo 12 Esta entrada es para las se ales a nivel de instrumentos Esta entrada produce una respuesta de frecuencias agudas tiple semejante al interruptor de brillo cuando se compara con la entrada normal NORMAL INPUT Entrada normal 13 Entrada para se ales de nivel de instrumento Para obtener respuestas de frecuencia m s brillantes altas ver Entrada de Brillo N mero 12 Sie 17 18 ae FUSE Fusible 14 El fusible se encuentra localizado dentro de la c psula del portafusible Si el fusible se quema o falla SE DEBERA REEMP
6. a los t cnicos calificados ADVERTENCIA Para evitar corrientazos o peligro de incendio no deje expuesto a la lluvia o humedad este aparato Antes de usar este aparato lea m s advertencias en la gu a de operaci n Ce symbole est utilis pour indiquer Putilisateur qu il ou qu elle trouvera d importantes instructions sur l utilisation et l entretien service de l appareil dans la litt rature accompagnant le produit Ce symbole est utilis pour indiquer l utilisateur la pr sence l int rieur de ce produit de tension non isol e dangereuse pouvant tre d intensit suffisante pour constituer un risque de choc lectrique ATTENTION Risques de choc lectrique NE PAS OUVRIR ATTENTION Afin de r duire le risque de choc lectrique ne pas enlever le couvercle Il ne se trouve l int rieur aucune pi ce pouvant tre r par e par l utilisateur Confier l entretien un personnel qualifi AVERTISSEMENT Afin de pr venir les risques de d charge lectrique ou de feu n exposez pas cet appareil la pluie ou l humidit Avant d utiliser cet appareil lisez les avertissements suppl mentaires situ s dans le guide d utilisation Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen die Handhabung und Wartung des Produkts betreffen Dieses Symbol soll den Anwender vor unisolierten gef hrlichen Spannungen innerhalb des Geh uses warnen die von Aus
7. nor does Peavey assume any responsbility or damage to interconnected non Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS LOST SAVINGS ANY INCIDENTAL DAMAGES OR ANY CONSE QUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IM PLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE PROVIDED HOWEVER THAT IF THE OTHER TERMS AND CONDI TIONS NECESSARY TO THE EXISTENCE OF THE EXPRESSED LIMITED WARRANTIES AS HEREINABOVE STATED HAVE BEEN COMPLIED WITH IM PLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE YEAR OR NINETY DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THESE LIMITED WARRANTIES ARE THE ONLY EXPRESSED WARRANTIES ON THIS PRODUCT AND NO OTHER STATEMENT REPRESENTATION WAR RANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY In the event o
8. of the product is for the purpose of resale or b The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER or The product has been damaged by accident or unreasonable use neglect improper service or maintenance or other causes not arising out of defects in material or workmanship or d The serial number affixed to the product is altered defaced or removed In the event of a defect in material and or workmanship covered by this limited warranty Peavey will a In the case of tubes or meters replace tho defective component without charge b In other covered cases le cases involving anything other than covers footswitches patchcorde tubes or matere repair the defect in material or workmanship or replace the product at Peavey s option and provided however that in any case all costs of shipping if necessary are paid by you the purchaser THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN 14 DAYS FROM THE DATE OF YOUR PURCHASE In order to obtain service under these warranties you must a Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therowith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product l the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest
9. 40 W RMS into 16 ohms Hum amp Noise Greater than 80 dB below rated power Power Consumption 200 watts 50 60 Hz 120 V AC Domestic PREAMP SECTION 2 ZAX7 S The following specs are measured 1 kHz with the controls preset as follows Pre amp Post lead 0 Reverb Level 0 Bass amp Treble EQ 12 Middle EQ 0 Master Volume 12 Presence 6 Nominal level is with Input Gain 6 Minimum levels is with Input Gain 12 Preamp Normal Input Impedance Very high Z 470 K ohms Lead Channel Post gain 10 Nominal Input Level 40 dBV 10 mV RMS Minimum Input Level 70 dBV 0 3 nV RMS Normal Channel Nominal Input Level 17 dBV 140 mV RMS Minimum Input Level 28 dBV 40 mV RMS Maximum Input Level 0 dBV 10 V RMS TONE SETTING Preamp Bright Input Impedance Very high Z 470 K ohms 12 dB boost 2 kHz Equalization Lead amp Normal Channels Custom bass middle amp treble passive type EQ Effects Send Load Impedance 1 kilohm or greater Nominal Output Level 6 dBV 0 5 V RMS Effects Return Impedance High Z 2 M ohms Designed Input Level 6 dBV 0 5 V RMS Switching jack provides Effects Send to Effects Return connection when not used External Footswitch Function Reverb Defeat when reverb control is raised Normal Lead Channel Select when Lead activated ADJUST TO TASTE wen 1 vi ADJUST TO TASTE TO ET AR ADJUST TO TASTE ROCK ADJUST TO TASTE ME
10. 9 Commande le volume g n ral du canal Lead Le r glage final de niveau doit tre effectu apr s avoir obtenu la sonorit d sir e l aide des autres r glages PRE GAIN 10 Contr le le niveau de volume l entr e sur du canal Lead NORMAL GAIN Gain canal normal 11 Contr le le niveau de volume du canal Normal BRIGHT INPUT Entr e Bright 12 Entr e pour signaux de niveau instrument Cette entr e produit une r ponse accentu e des fr quences aigu s similaire un s lecteur de brillance compar une entr e normale NORMAL INPUT Entr e normale 13 Entr e pour les signaux de niveau instrument Pour une r ponse en fr quence plus brillante hautes voir Bright Input No 12 FUSE Fusible 14 Le fusible se trouve l int rieur de son support Si le fusible grille IL DOIT TRE REMPLAC PAR UN FUSIBLE DE M ME TYPE ET M ME VALEUR POUR VITER TOUT DOMMAGE L APPAREIL ET VITER D ANNULER LA GARANTIE Si le fusible grille de fa on r p t e apportez l appareil un centre de service qualifi pour r paration AVERTISSEMENT LE FUSIBLE NE DOIT TRE REMPLAC QUE LORSQUE LE CORDON D ALIMENTATION EST D BRANCH DE LA SOURCE D ALIMENTATION SPEAKER OUTPUTS Sortie pour haut parleur 15 Les jacks 4 6 35 mm de sortie pour haut parleur sont pr vus pour 16 et 8 ohms Lorsque les deux jacks sont utilis s l imp dance de l amplificateur est d
11. LAZAR CON UNO DEL MISMO TIPO Y VALOR PARA EVITAR DA O AL APARATO Y EL ANULAMIENTO DE LA GARANTIA Si el aparato quema los fusible repetidamente cerci rese de que est conectado a un tomacorriente con el voltaje adecuado si esto es correcto entonces descon ctelo y ll velo a revisi n por un t cnico autorizado ATENCION Antes de reemplazar el fusible quemado cerci rese de que el aparato est completamente desconectado del tomacorriente SPEAKER OUTPUTS Salidas de parlante 15 Se proporcionan enchufes hembras de salida de parlante de 4 de pulgada para 16 y 8 ohmios Cuando se utilizan ambos conectores la impedancia de amplificador es de 8 ohmios REMOTE SWITCH JACK Enchufe hembra de interruptor remoto 16 Se suministra para la conexi n del pedal interruptor de control remoto opcional El pedal interruptor se utiliza para seleccionar los canales solista o normal y desactivar la reverberaci n Cuando utilice el pedal de control remoto inserte siempre la clavija completamente segundo ret n para asegurar el correcto funcionamiento EFFECTS RETURN Retorno de efectos 17 Entrada para el retorno de se ales procedentes de equipos de efectos externos o de equipos procesadores de se al EFFECTS SEND Env o de efectos 18 Salida para enviar se ales a efectos externos o equipos procesadores de se al FRANCAIS Veuillez vous r f rer au front panel line art situ dans la section en langue anglaise de ce manuel P
12. OWER SWITCH Interrupteur d alimentation 1 Mettre en position On pour mettre sous tension STANDBY SWITCH S lecteur attente 2 Permet de s lectionner l tat de l ampli mode Active actif ou mode Standby attente En position Stand by Pamplificateur ne fonctionne pas mais les lampes tubes restent chaudes pour permettre de le remettre en service sans d lai CHANNEL SELECT SWITCH S lecteur de canal 3 Permet de s lectionner les canaux Lead ou Normal NOTE La s lection de canal peut aussi s accomplir distance l aide de la p dale interrupteur Pour que la s lection distance soit possible le canal doit tre en position In Lead PILOT LIGHT LED DEL t moin 4 S allume lorsque l ampli re oit l alimentation CA PRESENCE Pr sence 5 R glage de tonalit actif qui renforce les fr quences extr mes aigu s 6 dB MASTER VOLUME Principal volume 6 Contr le le niveau de volume g n ral du syst me TREBLE MIDDLE AND BASS EQ galisation aigu s moyennes graves 7 R glages de tonalit passif ajustant respectivement les fr quences aigu s moyennes ct graves REVERB R verb ration 8 La r verb ration est un effet d cho Tournez dans le sens du mouvement des aiguilles d une montre pour augmenter l intensit de l effet L interrupteur au pied peut contr ler la mise en circuit ou hors circuit On Off POST GAIN
13. TAL ce NOOO USED FOR BRIGHTER SOUND WITH ENHANCED HIGHS SELECT DESIRED INPUT ADJUST TO TASTE See ADJUST TO TASTE COUNTRY SELECT DESIRED INPUT Tone settings given are general and will vary according to type of guitar type ard guages of strings type of pickup and even type of pick Personal taste playing style and type ol music great contribute to desired tonality ESPANOL Consulte los diagramas del panel delantero en la secci n de ingl s de este manual POWER SWITCH Interruptor de corriente 1 Coloque a la posici n on para encender STANDBY SWITCH Interruptor de condici n de espera 2 Este interruptor le permite a su aparato estar en condici n de espera o la condici n de activo En la condi ci n standby los tubos permanecen calientes pero el amplificador no est en operaci n CHANNEL SELECT SWITCH Interruptor de selecci n de canal 3 Permite la selecci n del canal Lead solista o Normal NOT ambi n se puede lograr la selecci n del canal por medio del pedal interruptor remoto Si desea la selecci n a control remoto el interruptor de canal debe estar en la posici n in hacia adentro canal de solista PILOT LIGHT LED LED indicadora de lampara piloto 4 Se ilumina cuando el amplificador recibe corriente alterna PRESENCE Presencia 5 Control de tono activo que aumenta en 6 dB las frecuencias de los extremos agudos
14. autsprecherausgange stehen klinkenbuchsen f r und 8 ohm zur Verf gung Wenn beide Buchsen belegt sind betr yt die Impedanz des Varst rkers 8 ohm REMOTE SWITCH JACK Remote Switch Jack 16 Vorgesehen f r den Anschlu des als Option erh ltlichen Fu schalters Der Fu schalter kann zum Anw hlen des Normal und Leadkanals sowie zum Schalten des Halls verwendet werden Um eine einwandfreie Funk tion zu gew hrleisten ist beim Anschlu des Fu schalters darauf zu achten da der Stecker vollst ndig bis zum 2 Klick eingesteckt ist ion erh ltlichen Fu schalters Der Fu schalter kann zum Anw hlen des Normal und Leadkanals sowie zum Schalten des Halls verwendet werden Um eine einwandfreie Funktion zu gew hr leisten ist beim Anschlu des Fu schalters darauf zu achten da der Stecker vollst ndig bis zum 2 Klick eingesteckt ist EFFECTS RETURN 17 Eingang f r die von externen Effektger ten zur ruckkommenden Signale EFFECTS SEND 18 Ausgang f r externe Effekte THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY Ces clauses de garantie ne sont vaiables qu aux Etats Unis et au Canada Dans tour les autres pays les clauses de garantie et de maintenance sont fixes par le distributeur national et assure par lul seion la legislation envigueur D
15. e 8 ohms REMOTE SWITCH JACK Prise pour interrupteur distance 16 Sert brancher la p dale interrupteur en option Linterrupteur au pied est utilis pour s lectionner les canaux Lead ou Normal et mettre la r verb ration hors service Afin d assurer un bon fonctionnement lors de Putilisation de l interrupteur au pied ins rez la fiche fond jusquau second cran au second clic EFFECTS RETURN Retour d effets 17 Prise d entr e pour signaux provenant d appareils externes de traitement de signal ou d effets EFFECTS SEND Envoi d effets 18 Prise de sortie servant fournir des signaux des appareils externes de traitement de signal ou d effets DEU CH Siehe Diagramm der Frontplatte im englischen Teil des Handbuchs POWER SWITCH 1 Zum Einschalten diesen Schalter auf on stellen STANDBY SWITCH 2 Erm glicht es den Verst rker mit abgeschaltetem Tonsignal betriebsbereit zu halten In der Standby Betriebsart werden die R hren weiter behcizt das Signal ist jedoch abgeschaltet CHANNEL SELECT SWITCH 3 Zur Umschaltung von Lead auf Normal Kanal MERKE Kanalwahl kann auch mittels dem Fernbedienungsfu schalter ausgef hrt werden Dazu mu der Channel Schalter sich in der in lead Position befinden PILOT LIGHT 4 Leuchtet auf wenn das Ger t eingeschaltet ist PRESENCE 5 Eine aktive Tonkontrolle welche die extrem hohen Frequenzen um 6 dB boostet anhebt
16. f any modification or disclaimer of expressed or implied warranties or any limitation of remedies contained herein conflicts with applicable law then such modification disclaimer or limitation as the case may be shall be deemed to be modified to the extent necessary to comply with such law Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to equipment purchased in the United States of America INSTRUCTIONS WARRANTY REGISTRATION CARD 1 Mail the completed WARRANTY REGISTRATION CARD to PEAVEY ELECTRONICS CORPORATION POST OFFICE BOX 2898 MERIDIAN MISSISSIPPI 39302 2898 a Keep the PROOF OF PURCHASE In the event warranty service is required during the warranty period you will need this document There will be no identification card issued by Peavey Electronics Corporation 2 IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESSES a Completion and mailing of WARRANTY REGISTRATION CARDS Should notification become necessary for any condition that may require correction the REGISTRATION CARD will help ensure that you are contacted and properly notified b Notice ol address changes from the address shown on the WARRANTY REGISTRATION CARD you should notify Peavey of the change of adress so as to faciltate your receipt cf any bulletins or other forms of notification which may become necessar
17. iese Garantie ist nur in den USA and Kanada gultig Alle Export Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen Esta garantia es valida solamente cuando el producto es comprado en E U continentales o en Canada Todos los productos que sean comprados en el extranjero estan sujetos a las garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes palses PEAVEY ONE YEAR LIMITED WARRANTY REMEDY PEAVEY ELECTRONICS CORPORATION PEAVEY warrants this product EXCEPT for covers footswitches patchcords tubes and meters to be free from defects in material anc workmanship for a period ot one 1 yaar from date of purchase PROVIDED however that this Im ten warranty is extended only 10 the original retail purchaser and is subject to the conditions exclusions and limitations horoinaftor sot forth PEAVEY 0 DAY LIMITED WARRANTY ON TUBES AND METERS It this product contains tubes or meters Peavey warrants the tubes or meters contained In the product to be free from defects in material and workmanship for a period of ninety 90 days from date of purchase PROVIDED however that this limited warranty is extended only to the original retall purchaser and is also subject to the conditions exclusions and limitations hereinatter set forth CONDITIONS EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES These limites warranties shall be void and of no effect if a The first purchase
18. inistration OSHA has specified the following permissible noise level exposures Duration Per Day In Hours Sound Level dBA Slow Response 90 92 93 97 100 d 102 105 10 s 115 Tue Y or According to OSHA any exposure in excess of the above permissible limits could result in some hearing loss Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits as set forth above To ensure against potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to equipment capable of produc ing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation SAVE THESE INSTRUCTIONS e Features and specifications subject to change without notice Peavey Electronics Corporation 711 A Street Meridian MS 39301 U S A 601 483 5365 Fax 486 1278 1995 80301946 Printed in U S A 6 95
19. other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service OR b Ship the defective item prepaid to PEAVEY ELECTRONICS CORPORATION International Service Center Highway 80 East MERIDIAN MS 39301 including therewith a complete detailed description of the problem together with a legible copy af the original PROOF OF PURCHASE and a completo return address Upon Peavey s receipt of these items If the defect is remocial under these limited warranties and the other terms and conditions expressed herein have been complied with Peavey will provide the necessary warranty service to repair or replace the product and will return it FREIGHT COLLECT to you the purchaser Peavey liability to the purchaser for damages from any cause whatsoever and regardless of the form of action including negligence is limited to the actual damages up to the greater of 8500 00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action Such purchase price will be that in effect for the specific product when the cause of action arose This limitation of liability will not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey s negligence Peavey does not assume liability for personal injury or property damage arising out of or caused by a non Poavoy alteration or attachment
20. reichender St rke sind um einen elektrischen Schlag verursachen zu k nnen VORSICHT Risiko Elektrischer Schlag Nicht ffnen VORSICHT Um das Risiko eines elektrischen Schlages zu vermeiden nicht die Abdeckung enfernen Es befinden sich keine Teile darin die vom Anwender repariert werden k nnten Reparaturen nur von qualifiziertem Fachper sonal durchf hren lassen ACHTUNG Um einen elektrischen Schlag oder Feuergefahr zu vermeiden sollte dieses Ger t nicht dem Regen oder Feuchtigkeit ausgesetzt werden Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen ENGLISH FRONT PANEL 3 12 13 Q E wa SH A Fe D I KE 18 1 2 4 5 6 7 8 9 11 POWER SWITCH 1 Switch to on position to turn on STANDBY SWITCH 2 Allows amp to be placed in standby or active mode In standby mode the tubes remain hot but the amplifier is not operational CHANNEL SELECT SWITCH 3 Allows selection of the Lead or Normal Channel NOTE Channel selection may also be accomplished by the remote footswitch If remote selection is desired the channel switch must be in the in Lead position PILOT LIGHT LED 4 Illuminates when AC power is being supplied to the amp PRESENCE 5 An active tone control that boosts the extreme high frequencies by 6 dB MASTER VOLUME 6 Controls the overall volume level of the system TREBLE MIDDLE AND BASS EQ 7 Passive tone controls that regulate high mid and low frequencies respectively
21. s especially at the plug and the point where the cord exits the unit 11 The power supply cord should be unplugged when the unit is to be unused for long periods of time 12 If this product is to be mounted in an equipment rack rear support should be provided 13 Metal parts can be cleaned with a damp rag The vinyl covering used on some units can be cleaned with a damp rag or an ammonia based household cleaner if necessary Disconnect unit from power supply before cleaning 14 Care should be taken so that objects do not fall and liquids other openings nto the unit through the ventilation holes or any re not spilled an if 15 This unit should be checked by a qualified service techni a The power supply cord or plug has been damaged b Anything has fallen or been spilled into the unit e The unit does not operate correctly d The unit has been dropped or the enclosure damaged 16 The user should not attempt to service this equipment All service work should be done by a qualified service technician 17 This product should be used only with a cart or stand that is recommended by Peavey Electronics 18 Exposure to extremely high noise levels may cause a permanent hearing loss Individuals vary considerably in susceptibility to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time The U S Government s Occupational Safety and Health Adm
22. y in connection with any condition that may require dissemination of information or correction 3 You may contact Peavey directly by telephoning 601 483 5365 IMPORTANT SAFETY INSTRUCTIONS WARNING When using electric products basic cautions should always be followed including the following 1 Read all safety and operating instructions before using this product 2 All safety and operating instructions should be retained for future reference 3 Obey all cautions in the operating instructions and on the back of the unit 4 All operating instructions should be followed 5 This product should not be used near water Le a bathtub sink swimming pool wet basement cte 6 This product should be located so that its position does no interfere with its proper ventilation Tt should not be placed flat against a wall or placed in a built in enclosure that will impede the flow of cooling air 7 This product should not be placed near a source of heat such as a stove radiator or another heat producing amplifier 8 Connect only to a power supply of the type marked on the unit adjacent to the power supply cord 9 Never break off the ground pin on the power supply cord For more information on grounding write for our free booklet Shock Hazard and Grounding 10 Power supply cords should always be handled carefully Never walk or place equipment on power supply cords Periodically check cords for cuts or signs of stres
Download Pdf Manuals
Related Search