Home

Patton electronic SmartNode 4960 Series User's Manual

1. TI FI ETH 0 1 Console PRI parts 0 400 10 100 1000Base T port RS 232 port ETH 0 0 RESET 10 100 1000Base T port button Figure 2 SN4960 rear panel SmartNode 4960 overview 16 SmartNode 4960 Getting Started Guide 1 General information Table 4 Rear panel ports Port Description WAN ETH 0 0 Auto MDX Gigabit Ethernet port RJ 45 see figure 2 connects the unit to an Ethernet WAN device for example a cable modem DSL modem or fiber modem Note Only full duplex modes are supported LAN ETH 0 1 Auto MDX GigabitEthernet port RJ 45 see figure 2 connect the unit to an Ethernet LAN for example a PC printer or wireless bridge Note Only full duplex modes are supported PRI 0 0 RJ 45 connector providing El 2 048Mbps or T1 1 533 Mbps PRI interface meet ing all requirements of ITU T recommendations for G 703 Use a shielded El or T1 interface cable for 120 Ohm balanced connections to connect the SmartNode with an NT or ET e g a PBX or LE PRI 0 1 RJ 45 connector providing El 2 048Mbps or T1 1 533 Mbps PRI interface meet ing all requirements of ITU T recommendations for G 703 Use a shielded El or T1 interface cable for 120 Ohm balanced connections to connect the SmartNode with an NT or ET e g a PBX or LE PRI 0 2 RJ 45 connector providing El 2 048Mbps or T1 1 533 Mbps PRI interface meet ing all requirements of ITU T recommendations for G 703 Use a shielded E1 or T1 interface c
2. Model PRI Ports Voice Channels SN4960 1E24V UI 24 SN4960 1E30V UI 30 SN4960 4E24V UI 4 24 SN4960 4E30V UI 4 30 SN4960 4E48V UI 4 48 SN4960 4E60V UI 4 60 SN4960 4E96V UI 4 96 SN4960 4E120V UI 4 120 SmartNode 4960 overview 14 SmartNode 4960 Getting Started Guide 1 General information Table 3 SmartNode 4960 models with integrated G SHDSL interface Model PRI Ports Voice Channels SN4960 1E24VG UI 1 24 SN4960 1E30VG UI 1 30 SN4960 4E24VG UI 4 24 SN4960 4E30VG UI 4 30 SN4960 4E48VG UI 4 48 SN4960 4E60VG UI 4 60 SN4960 4E96VG UI 4 96 SN4960 4E120VG UI 4 120 The SmartNode 4960 Gateway Router performs the following major functions e Up to 120 channels of Voice over IP and local voice switching via 1 or 4 PRI ports PRI ports can be oper ated in user or net mode Any port can be used as clock source Standard compliant VoIP in accordance with SIP or H 323 protocols Internet access and IP Routing with IP Quality of Service QoS support for mixed voice and data traffic Optional integrated G SHDSL bis WAN interface Up to 5 7 Mbps symmetrical throughput supporting ATM QoS Supports multiple PVC and DSLAM interoperability SmartNode 4960 overview 15 SmartNode 4960 Getting Started Guide 1 General information SmartNode 4960 rear panel The SmartNode 4960 rear panel ports are described in table 4 TI FI PRI port 0 0
3. 20 SmartNode 4960 Getting Started Guide 2 Applications overview Introduction Patton s SmartNode VoIP Media Gateway Routers deliver the features you need for advanced multiservice voice and data network applications They combine high quality voice over IP with powerful quality of service routing functions to build professional and reliable VoIP and data networks This chapter describes typical applications for which this SmartNode is uniquely suited Note Detailed configuration information for the applications can be found on the CD ROM cthat was included with your SmartNode device or online from the Patton webserver at www patton com Application Edge intelligence of enterprise communication Enterprises are excited about voice over IP and convergence for the following reasons e Bypassing the PSTN Using Internet telephony service providers ITSPs instead of incumbent carriers dra matically reduces telephony costs P PBXs with their full suite of features and ease of integration into existing IT environments are very appealing Convergence lowers technology ownership costs and enables enterprises to deploy new integrated applications However there are several concerns about migrating the whole telephony infrastructure to VoIP Loss of voice quality Unknown reliability Lack of experience expertise in voice over IP Patton s SmartNode series of VoIP gateways address these concerns enabling enterprises to safely
4. Built in diagnostic tools trace debug Secure Auto provisioning System CPU Motorola MPC8360 series operating at 266 400 MHz Memory 128 Mbytes RAM DDR 266MHz 8 Mbytes Flash Physical Dimensions 11 9W x 1 71H x 7 16D inch 302W x 44H x 182mm Weight 21 oz 600g Power Consumption 16W Operating temperature 32 104 F 0 40 C Operating humidity up to 9096 non condensing IP services 52 SmartNode 4960 Getting Started Guide B Specifications G SHDSL Daughter Card if applicable Note For information on configuring the G SHDSL daughter card see Chapter 5 G SHDSL Basic Configuration on page 38 Table 12 G SHDSL Daughter Card Specifications Specs Factor DSL e ITU T G 991 2 and Amendment 2 e ITU T G 991 2 Annex A B F G Upgradable to ITU T G shdsl bis Annex F and G e G 991 2 2 4 1 2 pair operation G 994 1 G hs per G 991 2 e ITU T G 991 2 Section E 9 TPS TC for ATM transport e ITU T G 991 2 Section E 11 TPS TC for PTM transport DSL Connection RJ 11 12 2 wire Management e 1610 OAM FA F5 Management interfaces GUI and Telnet e Software upgrade GUI and TFTP ATM Support Classical IPoA RFC 1577 2225 e PPPoE Client over ATM RFC 2516 e IPoA RFC 2684 1483 e ATM AALS encapsulation Max 8 PVCs User selectable VC MUX and LLC MUX default Configurable auto connection ATM QoS UBR default CBR and VBR rt
5. source code object code or executable code C End User shall mean the person or organization which has valid title to the Designated Equipment D Designated Equipment shall mean the hardware on which the Program s have been designed and pro vided to operate by Patton Electronics Company 2 Title Tide to the Program s all copies of the Program s all patent rights copyrights trade secrets and proprietary information in the Program s worldwide remains with Patton Electronics Company or its licensors 3 Term The term of this Agreement is from the Effective Date until title of the Designated Equipment is transferred by End User or unless the license is terminated earlier as defined in section 6 Termination on page 67 4 Grant of License A During the term of this Agreement Patton Electronics Company grants a personal non transferable non assignable and non exclusive license to the End User to use the Program s only with the Designated Equipment at a site owned or leased by the End User B The End User may copy licensed Program s as necessary for backup purposes only for use with the Des ignated Equipment that was first purchased or used or its temporary or permanent replacement C The End User is prohibited from disassembling decompiling reverse engineering or otherwise attempt ing to discover or disclose the Program s source code methods or concepts embodied in the Program s or having the same done by another
6. us race etre eet eppure talar 41 Using PVC channels in bridged Ethernet mode enne REI ERR 41 Using PVG channels th PPPOE EE MR N EA ERE cis 41 IBI Ta DII MEE 42 Troubleshooting DSL Connections AE er ERE bete bed a eas usen E EE EA Ee 42 6 Contacting Patton for assistance eese esee See Bee Bee Be ee SE EE EE RE AE E ee ee enses senses senses esses ens ens SEE Bee Bee See see se 45 onn ED OE EE ER EE EE 44 Contact Te EA OE RE ELSE den PEU es 44 Patton support headquarters an the USA aii etr o D RD ed ta o edere ged 44 Alternate Patton support for Europe Middle East and Africa EMEA esee 44 Warranty Service and Returned Merchandise Authorizations RMAs se ee se ee Ge ee Re Re RA eerte Ge Re 44 Warranty ERA DA OE EA AA ER OR AE 44 T e a e ER A N O 45 RS EU DENS Tob POU EG hie eO ti dite E one tert E RR tns 45 Return for eredt polig unirnos il OE EN 45 Rada 45 Shipping INSEFRGHONI XE 45 A Compliance information ee es 46 Corap c REEL EET 47 lp 47 Crac E E PEDRO CURE RE RATA M 47 PSTN Besulatoty AE OE RE EE nU e d m eed Des 47 Radiant CV ei oe uu AE EE EA nOn OE EE 47 BCG Part 68 ACTA Se dd I 47 Industry Ca ada Notice EE EA OR EA EE ERE Reve 48 GENRE ET ol Con Ormi ii aaa 48 SmartNode 4960 Getting Star
7. 1 1 if ip WAN ipaddress 172 16 1 99 255 255 255 0 2002 10 29T00 09 40 LOGINFO Link down on interface WAN 2002 10 29T00 09 40 LOGINFO Link up on interface WAN 172 16 1 99 if ip WAN Copy this modified configuration to your new start up configuration This will store your changes in non vol atile memory Upon the next start up the system will initialize itself using the modified configuration 172 16 1 99 if ip WAN copy running config startup config 172 16 1 99 if ip WAN The SmartNode can now be connected to your network 3 Connecting the SmartNode to the network In general the SmartNode will connect to the network via the WAN ETH 0 0 port This enables the Smart Node to offer routing services to the PC hosts on LAN ETH 0 1 port The SmartNode 4960 Series is equipped with Auto MDX Ethernet ports so you can use straight through or crossover cables for host or hub switch connections see figure 8 and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use LAN ETH 0 1 WAN ETH 0 0 Straighi through wired or crossover cable Figure 8 Connecting the SmartNode to the network 3 Connecting the SmartNode to the network 32 SmartNode 4960 Getting Started Guide 4 e Initial configuration You can check the connection with the ping
8. Once the IP PBX is ready you can choose on incoming calls from the PSTN for each extension whether this extension is to be directed to the IP PBX or on the legacy PBX Application Multi service ISDN Internet telephony IAD The SmartNode 4960 Series can be used to make and receive calls to and from the public ISDN network and Internet Telephony services on any ISDN Terminal Phone or PBX see figure 5 Using individually config urable routing tables an outbound call can be directed to the local PSTN connection or to an Internet tele phony service provider ISTP Inbound calls from the Internet and the PSTN can ring the same phone WAN Ethernet external broadband access Internet My LAN to WAN QoS Routing and Security Figure 5 Internet telephony IAD application Broadband network connectivity integrates with any fixed IB DHCP or PPPoE service An integrated Gigabit Ethernet LAN port with advanced routing features such as NAT Firewall ACL DynDNS as well as optional IPSec VPN fulfills the requirements of demanding network users Quality of Service QoS features complete the offering with advanced voice prioritization and traffic manage ment Patton s patent pending DownStreamQoS ensures voice without interruptions even over best effort Internet connections Application Multi service ISDN Internet telephony IAD 22 Application Multi service ISDN Internet telephony IAD 23 Cha
9. amp 3 are connected together Figure 17 EIA 561 RJ 45 8 pin port Note N C means no internal electrical connection Ethernet Table 14 RJ45 socket 10 100Base T 1 2 3 RX 6 Note Pins not listed are not used Introduction 61 SmartNode 4960 Getting Started Guide D Port pin outs Table 15 RJ45 socket 1000BaseT TRDO TRDO TRD1 TRD 1 TRD2 TRD2 TRD3 TRD3 oo NI Oi AY Os Gy N PRI port Table 16 R 45 socket RX Ring RX Tip RX Shield TX Ring TX Tip TX Shield S Gy KY GI N Note Pins not listed are not used G SHDSL port Table 17 RJ 11 connector No connection Tip Ring S oj N No connection Note Pins not listed are not used PRI port 62 Appendix E SmartNode 4960 factory configuration Chapter contents IU io T RED TCU ENTE Um ira HE N THEE 64 63 SmartNode 4960 Getting Started Guide E SmartNode 4960 factory configuration Introduction The factory configuration settings for SmartNode 4960 are as follows L EE EE EE EE ET EE EE EE DEE DEE EE EE EE EE 4960 Series Factory configuration file EE dns relay sntp client sntp client server primary 129 132 2 21 port 123 version 4 system ic voice 0 low bitrate codec g729 profile napt NAPT WAN profile dhcp server DHCPS LAN network 192 168 1 0 255 255 255 0 include 1 192 168 1 10 1
10. migrate to VoIP SmartNodes enable system administrators to gradually introduce VoIP using it as the edge communica tion device for all worlds connecting PSTN legacy PBX ITSPs and an IP PBX SmartNode 4960 Legacy PBX PSTN Internet y IP PBX Figure 4 Edge intelligence of enterprise communication application Introduction 21 SmartNode 4960 Getting Started Guide 2 Applications overview How it works 1 Connect the SmartNode to the PSTN and legacy PBX and configure the call router to pass all calls from the PBX to the PSTN and vice versa This first step will not affect any uses in the enterprise 2 Choose your ITSPs and configure as many on the SmartNode as you need Use the intelligent call router in the SmartNode to decide which call is forwarded to which ITSP and which calls should go to the PSTN This may be based upon least cost routing criteria or for example on calling party number The latter is ideal if you want to test calls to an ITSP before enabling it for all users within the enterprise 3 Voice over IP can be switched off instantly on one single box the SmartNode to revert the system back to as it was before 4 Build up an IP PBX system that uses the SmartNode as PSTN gateway For all calls from this IP PBX you can direct them to the PSTN or to ITSPs Numbering plan adaptations are handled through regular expression matching by the SmartNode No need to change anything on the PBXs 5
11. modem detection Codec fallback for modem bypass T 38 Fax Relay Gr 3 Fax 9 6 k 14 4 k G 711 Fax Bypass Voice signalling SIPv2 H 323v4 MGCP IUA SIP call transfer redirect Overlap or en bloc dialing DTMF in band out of band Configurable progress tones Voice routing session router Local switching hairpinning Least cost routing Interface huntgroups Call Distribution groups Number blocking Call Routing Criteria Interface e Calling called party number Time of day day of week date ISDN bearer capability Various other information elements IEs of the ISDN setup e Wildcard and regular expression matching Regular expression number manipulation functions Replace numbers e Add remove digits e Pattern matching and replacement Fax and modem support 51 SmartNode 4960 Getting Started Guide B Specifications IP services IPv4 router RIPv1 v2 RFC 1058 and 2453 Programmable static routes ICMP redirect RFC 792 Packet fragmentation DiffServe ToS set or queue per header bits Packet Policing discards excess traffic 802 1p VLAN tagging IPSEC AH amp ESP Modes Manual Key IKE AES DES 3DES Encryption Management Web based GUI Industry standard CLI with local console RJ 45 RJ 231 9600 bps 8 N 1 and remote Telnet access fully documented HTTP web management and firmware loading TFTP configuration amp firmware loading SNMP v1 agent MIB II and private MIB
12. not responsible for equipment returned without a Return Authorization Return for credit policy Less than 30 days No Charge Your credit will be issued upon receipt and inspection of the equipment 30 to 60 days We will add a 20 restocking charge crediting your account with 80 of the purchase price Over 60 days Products will be accepted for repairs only RMA numbers RMA numbers are required for all product returns You can obtain an RMA by doing one of the following Completing a request on the RMA Request page in the Support section at www patton com By calling 1 301 975 1007 and speaking to a Technical Support Engineer By sending an e mail to returns patton com All returned units must have the RMA number clearly visible on the outside of the shipping container Please use the original packing material that the device came in or pack the unit securely to avoid damage during shipping Shipping instructions The RMA number should be clearly visible on the address label Our shipping address is as follows Patton Electronics Company RMA xxxx 7622 Rickenbacker Dr Gaithersburg MD 20879 4773 USA Patton will ship the equipment back to you in the same manner you ship it to us Patton will pay the return shipping costs Warranty Service and Returned Merchandise Authorizations RMAs 45 Appendix A Compliance information Chapter contents A uie E E E A dme A O eed 47 ie RR is 47 SIC m 47 A eet e e e Lee ETE
13. of direct routing has at least one active VolP connection Off indicates the unit is not configured or registered or has no active direct routed VolP connection Flashing green indicates that the unit is attempting to register or has failed to register Ethernet Link On when the Ethernet connection on the corresponding port has a link indication Ethernet Speed 10 100 When the Ethernet Link LED is on then On when the Ethernet is connected to a 100Mb network Off when the Ethernet is connected to a 10Mb network Ethernet Speed 1000 Ethernet Activity On when the Ethernet is connected to a 1000Mb network Flashes when data is received or transmitted at the corresponding Ethernet port PRI Link Status On in frame no errors Flash Error Fast Flash Signal detected but no frame synchronization or aquisition is in process Slow Flash Framing synchronized Signaling not established G SHDSL ACT Rear panel Flashes when data is received or transmitted Off No activity G SHDSL LINK Rear panel On when the G SHDSL connection on the corresponding port has a link indication Off 2 No G SHDSL connection SmartNode 4960 overview 19 Chapter 2 Applications overview Chapter contents oduct A MA EE N OE AE EE EO ID 21 Application Edge intelligence af enterprise commuhblicatigbe oie eer EER GER E AEA 21 Application Multieservace ISDN Interner telephony Abin po
14. symmetrical throughput supporting ATM QoS Supports option multiple PVC and DSLAM interoperability The G SHDSL LEDs are located on either side of the DSL port ACT when lit or blink ing shows Activity and LINK when lit shows that the DSL port is connected SmartNode 4960 overview 17 SmartNode 4960 Getting Started Guide 1 General information SmartNode 4960 front panel Figure 3 shows SmartNode 4960 front panel LEDs the LED definitions are listed in table 5 SN4960 1E PATTON SmartNode 4960 VoIP IAD T1 E1 PRI Media Gateway Router Bhemet 00 Ethemet oi amp Power As ves sos Ethernet 0 1 7 VolP Activity T1 E1 Port 0 Ethernet 0 0 Ethernet 0 0 Ethernet 0 1 V Ethernet 0 1 li 1000 Link 1000 ink Ethernet 0 0 Ethernet 0 0 Ethernet 0 1 100 Activity 100 SN4960 4E PEITOS SmartNode 4960 VoIP IAD d pool pre SET T1 E1 Port 0 T1 E1 Port 3 T1 El Port TI El Port 2 Figure 3 SmartNode 4960 front panel SmartNode 4960 overview 18 SmartNode 4960 Getting Started Guide 1 General information Table 5 SN4960 Front and Rear panel LEDs LED Description Note If an error occurs all LEDs will flash once per second Power When lit indicates power is applied Run When lit the unit is in normal operation Flashes once per second during boot startup VoIP Link On indicates the gateway is registered to an H 323 gatekeeper SIP server or in the case
15. y Erase from 0x60030000 0x6010b3ba iie 92 MERKER ES RES He ss Program from 0x00011eec 0x00011ef4 at 0x60030000 Program from 0x01800100 0x0199b4b2 at 0x60030008 eee Program from 0x00011eec 0x00011ef4 at 0x60030000 Image successfully written to flash RedBoot gt fis list 1 Id Address Length State Description Entry Load Addr Version 1 0x60030000 1693438 valid SmartWare R2 10 BUILD28015 0x01800100 0x01800100 V2 10 RedBoot gt go Starting SmartWare R2 10 BUILD28015 at 0x01800100 via 0x01800100 Load a new application image SmartWare via the serial link The Bootloader supports the X Modem and Y Modem protocols to download application images via the serial link of the console Do the following to initiate the download Step Command Purpose 1 RedBoot gt load r v m Downloads an application image into the volatile memory xmodem ymodem b RAM from where the SmartNode could directly execute it base address xmodem or ymodem Specify the protocol to be used X Modem or YModem base address memory location where to store the application image Use the default address 0x1800100 Execute the above RedBoot command first then start the trans fer from the terminal program with the command Send file via X Modem or similar 5 RedBoot fis delete n 1 Deletes the first application image Reply with y to the confirmation request 6 RedBoot gt fis create Store
16. 47 Radiorand T V T ORE AA GP RETI IUD dtd 47 REC Par INE ETA SERE AS A morer RERO mere 47 Industry Canada NOU eene nene nente een ERE RUNI OECD Ra EI EE E 48 OER o ETR ie Conai 48 46 SmartNode 4960 Getting Started Guide A Compliance information Compliance EMC e FCC Part 15 Class A EN55022 Class A EN55024 Safety UL 60950 1 CSA C22 2 NO 60950 1 EC EN60950 1 e AS NZS 60950 1 PSTN Regulatory e FCC Part 68 e CS 03 TBR 12 amp 13 El e AS ACIF S016 2001 E1 e AS ACIF S043 2003 G SHDSL card Radio and TV Interference The SmartNode router generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception The SmartNode router have been tested and found to comply with the limits for a Class A comput ing device in accordance with specifications in Subpart B of Part 15 of FCC rules which are designed to pro vide reasonable protection from such interference in a commercial installation However there is no guarantee that interference will not occur in a particular installation If the SmartNode router does cause interference to radio or television reception which can be determined by disconnecting the unit the user is encouraged to try to correct the interference by one or more of the following measures moving the computing equipment away from the receiver
17. 51 Voice POUL Ee AR EA O An 51 lr 3 D E 52 Management AE AE OE USER ON EE EE CPR 52 SE AR ER EG 52 BE ies ME N ER EE ER O RO m M M RO See 52 GSEDSE auster Crd OF applicable reos 59 Tdenuhiestiomot the Smart Node devices St Decem ee er episode ee oe ase sheen e TT 54 49 SmartNode 4960 Getting Started Guide B Specifications Note Refer to the software feature matrix for the most up to date specifications DSP One or two 60 channel DSPs Voice connectivity 1 or 4 PRI T1 E1 ports on RJ48C connectors Net User configurable per port Each port can be slave or master clock Each port can be used to synchronize to an external clock master Data connectivity Two 10 100 1000Base Tx Gigabit Ethernet ports All ports full duplex autosensing auto MDX Voice processing signalling dependent Four or eight full duplex channels with Voice CODECS e G 711 A Law p Law 64 kbps e G 726 ADPCM 16 24 32 40 kbps G 723 1 5 3 or 6 3 kbps e G 729ab 8 kbps Transparent ISDN data G 168 echo cancellation 128 ms Up to 120 simultaneous voice or 1 38 fax calls DTMF detection and generation Carrier tone detection and generation Silence suppression and comfort noise Adaptive and configurable dejitter buffer Configurable tones dial ringing busy Configurable transmit packet length RIP RTCP RFC 1889 DSP 50 SmartNode 4960 Getting Started Guide Fax and modem support B Specifications Automatic fax and
18. 92 168 1 99 lease 2 hours default router 1 192 168 1 1 domain name server 1 192 168 1 1 context ip router interface WAN ipadress dhcp use profile napt NAPT WAN tcp adjust mss rx mtu tcp adjust mss tx mtu interface LAN ipadress 192 168 1 1 255 255 255 0 tcp adjust mss rx mtu tcp adjust mss tx mtu context ip router dhcp server use DHCPS LAN port ethernet 0 0 medium auto encapsulation ip bimd interface WAN router no shutdown port ethernet 0 1 medium auto encapsulation ip bind interface LAN router no shutdown Introduction 64 Appendix F End user license agreement Chapter contents End User license Mareementa mitos ce DA EE UU IRR EOS 66 ER ii LR SUA DR RR RR N RR AK ER ORE S 66 Slide dU E EE Me 66 Duero eee sce N oe Ee DA ED ek ee N e AE p ete Ee RU d 66 A Nata trap Te a one mene EU UR NO 66 RUIT ECC OTO PUTET 66 G Bees sued eee t eet een DE pe reer ee onera RR HIE 67 E RIA UICE NECI UNO DDR ET EA 67 65 SmartNode 4960 Getting Started Guide F End user license agreement End User License Agreement By opening this package operating the Designated Equipment or downloading the Program s electronically the End User agrees to the following conditions 1 Definitions A Effective Date shall mean the earliest date of purchase or download of a product containing the Patton Electronics Company Program s or the Program s themselves B Program s shall mean all software software documentation
19. E RA ORE NUDO EE 27 Connecting the 10 100 1000Base T Ethernet LAN and WAN cables eene 27 Enstaline the DSE WAN gable canna E E ER DU RETE ee e A en py es te powersupply eene AA EMI 28 AG EE EIE ei EG ree URDU TUE 29 IT T TEE 30 It onnecane tie pare Nodeto ou EDU eere TT e EA dee 30 SmartNode 4960 Getting Started Guide Table of Contents 2 Configurime thedesired IP e ee deo iio 31 Factory default IP Settings 2 optet EE OO Deu IC oT ON HE 31 I E 31 Changing the WAIN IP address seas EE ad 31 3 Gonnecting the SmartNode tothe NetWork esse se SE Eo cai ties 32 Loading the conhguration optional neri EL e eee E ege ae gee lia 33 Bootloader M 34 ET ele ore ide donando Ie 34 Start up with factory configuration ponia lisas 34 Load a new application image SmartWare via TETP iii 34 Load a new application image SmartWare via the serial link iii 36 Additional information ssa iaa il ia 37 5 G SHDSL Basic Configuration see see sesse ese ese ese see eee See Bee eese ee Se tns GE RE AE BEE ee ee Ee Re BEE BEE EE Bee essen sens entia sensns see se 38 Introduction o eae siepe Oe be E N AR ET RE petu p OE EE 39 Line Te uile ER NANAS 39 Contiguiing PPPoE illa OE etre te rati OE p Prud ada pap OR a 39 OTT LE ig RENE ladina lia ia 40 Setting tip permanent victual cueuits PV
20. End user license agreement on page 65 or go to www patton com Patton Electronics warrants all SmartNode router components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of the shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If the product fails to perform as warranted your sole recourse shall be repair or replacement as described above Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics specifically disclaims all other warran ties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user Summary Table of Contents iosa 13 AQ TIE EE DEO CON title iii AE EE DA PRP 20 E e ETT EE TER EE TU T TE 24 AR antie configurano irritanti 29 5 GSHDSE Basic Conk purati Ona 38 E E A Ratton for T EE E 43 A Compliance Information AE irea IEEE EAEE EE ETERO RENES 46 BS T E T EE E E E E 49 GE ins e TT 55 ID LESE EL ii 60 E SmartNode 4960 factory con tamed tian coca e esse see tesi tenue ee retis Re oe des Ce eese esse ged ge ee ape ee El oge
21. P PATTON E Ea ElectronicsTo SmartNode 4960 Series T1 E1 PRI VoIP Router Getting Started Guide Sales Office 1 301 975 1000 Technical Support 1 301 975 1007 E mail support patton com WWW www patton com Document Number 13223U1 001 Rev B Part Number 07MSN4960 GS Revised November 15 2006 Patton Electronics Company Inc 7622 Rickenbacker Drive Gaithersburg MD 20879 USA Tel 1 301 975 1000 Fax 1 301 869 9293 Support 1 301 975 1007 Web www patton com E mail support patton com Trademark Statement The terms SmartNode and SmartWare are trademarks of Patton Electronics Company All other trademarks presented in this document are the property of their respective Owners Copyright O 2005 2006 Patton Electronics Company All rights reserved The information in this document is subject to change without notice Patton Elec tronics assumes no liability for errors that may appear in this document Important Information To use virtual private network VPN and or AES DES 3DES encryption capabilities with the SmartNode 4960 you may need to purchase additional licenses hardware software network connection and or service Contact sales patton com or 1 301 975 1000 for assistance Warranty Information The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license For information about the license see Appendix E
22. VBR nrt UBR per VC queuing Auto configuration TR 037 amp ILMI 4 0 Interworking Interoperability G SHDSL Interoperability Alcatel NEC lucent Anymedia lucent Stinger BRAS Interoperobility Cisco Redback G SHDSL Daughter Card if applicable 53 SmartNode 4960 Getting Started Guide B Specifications Identification of the SmartNode devices via SNMP All SmartNode devices have assigned sysObjectID iso org dod internet mgmt mib 2 system sysObjectd D numbers see table 13 Table 13 SmartNode Models and their Unique sysObjectlD SmartNode Model SysObjectlD SNA4960 1E15V UI iso org dod internet private enterprises patton products sn49xx 1 1 3 6 1 4 1 1768 100 4 10 1 SN4960 1E24V UI iso org dod internet private enterprises patton products sn49xx 2 1 3 6 1 4 1 1768 100 4 10 2 SN4960 1E30V UI iso org dod internet private enterprises patton products sn49xx 3 1 3 6 1 4 1 1768 100 4 10 3 SN4960 4E15V UI iso org dod internet private enterprises patton products sn49xx 4 1 3 6 1 4 1 1768 100 4 10 4 SN4960 4E24V UI iso org dod internet private enterprises patton products sn49xx 5 1 3 6 1 4 1 1768 100 4 10 5 SN4960 4E30V UI iso org dod internet private enterprises patton products sn49xx 6 1 3 6 1 4 1 1768 100 4 10 6 SN4960 4E48V UI iso org dod internet private enterprises patton products sn49xx 7 1 3 6 1 4 1 1768 100 4 10 7 SN4960 4E60V UI iso org do
23. able for 120 Ohm balanced connections to connect the SmartNode with an NT or ET e g a PBX or LE PRI 0 3 RJ 45 connector providing El 2 048Mbps or T1 1 533 Mbps PRI interface meet ing all requirements of ITU T recommendations for G 703 Use a shielded El or T1 interface cable for 120 Ohm balanced connections to connect the SmartNode with an NT or ET e g a PBX or LE Console Used for service and maintenance the Console port see figure 2 an RS 232 RJ 45 connector connects the product to a serial terminal such as a PC or ASCII terminal also called a dumb terminal 100 240 VAC 50 Electricity supply socket for mains power cable see figure 2 60 Hz Reset The reset button see figure 2 has three functions Restart the unit with the current startup configuration Press for less than 1 second and release the Reset button to restart the unit with the current startup configuration Restart the unit with factory default configuration Press the Reset button for 5 seconds until the Power LED see figure 3 on page 18 starts blinking to restart the unit with factory default configuration Restart the unit in bootloader mode to be used only by trained SmartNode tech nicians Starting with the unit powered off press and hold the Reset button as you apply power to the unit Release the Reset button when the Power LED starts blinking so the unit will enter bootloader mode G SHDSL port Provides up to 5 7 Mbps
24. at sources Protect the unit from moisture vapors and corrosive liquids Typographical conventions used in this document This section describes the typographical conventions and terms used in this guide General conventions The procedures described in this manual use the following text conventions Table 1 General conventions Convention Meaning Garamond blue type Indicates a cross reference hyperlink that points to a figure graphic table or sec tion heading Clicking on the hyperlink jumps you to the reference When you have finished reviewing the reference click on the Go to Previous View button in the Adobe Acrobat Reader toolbar to return to your starting point Futura bold type Commands and keywords are in boldface font Futura bold italic type Parts of commands which are related to elements already named by the user are in boldface italic font Italicized Futura type Variables for which you supply values are in italic font SmartNode 4960 Getting Started Guide Table 1 General conventions Convention Meaning Futura type Indicates the names of fields or windows Garamond bold type Indicates the names of command buttons that execute an action Angle brackets indicate function and keyboard keys such as lt SHIFT gt lt CTRL gt C and so on lt gt Elements in square brackets are optional a b c Alternative but require
25. ation image mask len is the length of the network address or the number of 1 s within the subnet mask See Note below Bootloader 34 SmartNode 4960 Getting Started Guide 4 Initial configuration Step Command Purpose 2 RedBoot ip address g gateway Sets the IP address of the default gateway optional 3 RedBoot gt ping h ipserver ip address Tests the connectivity to the TFTP server optional 4 RedBoot load r v h host b Downloads an application image into the vola base address file name tile memory RAM from where the SmartNode could directly execute it host IP address of the TFTP server base address memory location where to store the application image Use the default address 0x1800100 file name path and name of the file on the TFTP server Note use the image file that con tains the whole application not the image paris 5 RedBoot gt fis delete n 1 Deletes the first application image Reply with y to the confirmation request 6 RedBoot gt fis create Stores the downloaded application image to the permanent memory flash Reply with y to the confirmation request 7 RedBoot gt fis list l Checks whether the image has been success fully stored whether it is the desired Release and Build and whether it is valid 8 RedBoot gt go Starts the application image that was down loaded into the volatile memory RAM Note With the Bootloader
26. ation images e g SmartWare via the serial link of the console Start Bootloader To start the Bootloader power on the SmartNode while pressing the reset button Open a Telnet session to the SmartNode via one of the Ethernet interfaces or open a CLI session via the console port if available on the SmartNode The login display will appear Using the credentials admin patton log in to the SmartNode The following prompt will be displayed RedBoot Type help to display an overview of the available commands Start up with factory configuration Step Command Purpose 1 RedBoot fis load Copies the SmartWare application image from the persistent memory flash to the volatile memory RAM from where it will be executed 2 RedBoot go s factory config Starts the SmartWare application telling it to use factory config as startup configuration You can also start up with any other configuration available in the persistent memory nvram by pro viding its name instead of factory config Load a new application image SmartWare via TFTP The following procedure downloads the application image SmartWare for the mainboard See the note below on how to download the respective CLI description file Step Command Purpose 1 RedBoot gt ip address Sets the IP address and subnet mask of the optional ocal ip address mask len Ethernet interface 0 0 which shall be used to receive the new applic
27. be connected to a serial terminal over its serial console port as depicted in figure 10 and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use Serial Terminal Note A Patton Model 16F 561 RJ45 to DB 9 adapter is included with each SmartNode 4960 Series device Figure 10 Connecting a serial terminal Note See section Console port on page 61 for console port pin outs Introduction 56 SmartNode 4960 Getting Started Guide C Cabling Ethernet Ethernet devices 10Base T 100Base T 1000Base T are connected to the SmartNode over a cable with RJ 45 plugs All Ethernet ports on the SN4960 are Auto MDX use any straight or crossover cable to connect to hubs switches PCs or other devices and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use Straight through cable RJ 45 male RJ 45 male 1 gt 1 2 2 3 6 6 Note Other pins are not used Figure 11 Typical Ethernet straight through cable diagram for 10 100Base T RJ 45 male RJ 45 male l DV Z KYDVV L co N UI aio Co N N uU A Og Co N Figure 12 Typical Ethernet straight through cable d
28. be used to connect the PRI Each port can be configured as NT clock master or TE clock slave For details on the PRI port pin out and ISDN cables refer to Appendix C Cabling on page 43 and Appen dix D port pin outs on page 47 Connecting the 10 100 1000Base T Ethernet LAN and WAN cables The SmartNode 4960 has automatic MDX auto crossover detection and configuration on all Ethernet ports Any of the ports can be connected to a host or hub switch with a straight through or cross over wired cable 1 Connect to the subscriber port of the broadband access modem DSL cable WLL to ETH 0 0 Note TheSmartNode Ethernet ports operate in Full Duplex mode only Do not connect to Half Duplex ports For best results use auto negotiation Auto negotiation is mandatory when using 1000BaseT Gigabit Ethernet 2 Connect port ETH 0 1 to your LAN Installing the DSL WAN cable The SmartNode Model 4960 comes with an option for a G SHDSL WAN interface Use a straight through RJ 11 cable to connect the G SHDSL port For details on the Ethernet port pinout and cables refer to Appendix C Cabling on page 55 and Appendix D Port pin outs on page 60 Installing the gateway router 27 SmartNode 4960 Getting Started Guide 3 SmartNode installation Connecting the power supply Do the following to connect the main power to the Model 4960 Note Do not connect the power cord to the AC power outlet at this time l Insert the female e
29. chapter 4 Initial configuration on page 29 Placing the SmartNode Place the unit on a desktop or similar sturdy flat surface that offers easy access to the cables The unit should be installed in a dry environment with sufficient space to allow air circulation for cooling Note For proper ventilation leave at least 2 inches 5 cm to the left right front and rear of the unit Installing cables Do not work on the system or connect or disconnect cables during periods of A lightning activity WARNING Installing the gateway router 26 SmartNode 4960 Getting Started Guide 3 SmartNode installation Connect the cables in the following order and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use 1 Connect the T1 E1 cables to the PRI T1 E1 ports see Appendix C on page 55 and Appendix D on page 60 2 Connect the 10 100 1000Base T Ethernet LAN and WAN see section Connecting the 10 100 1000Base T Ethernet LAN and WAN cables on page 27 3 Connect the power mains cable see section Connecting the power supply on page 28 Connecting the PRI The SmartNode comes with one or four PRI ports These ports are usually connected to a PBX or switch local exchange LE Each PRI T1 E1 port is a RJ 48C receptacle In most cases a straight through RJ 45 can
30. command from the SmartNode to another host on the network 172 16 1 99 if ip WAN fping IP Address of the host Note If the WAN address is not set to DHCP to ping a device outside your local LAN you must first configure the default gateway For information on con figuring the default gateway refer to section Set IP addresses in Appendix C Command Summary of the SmartNode Series SmartWare Software Con figuration Guide 4 Loading the configuration optional Patton provides a collection of configuration templates on the CD ROM that came with the SmartNode device and also on the support page at www patton com voip one of which may be similar enough to your application that you can use it to speed up configuring the SmartNode Simply download the configuration note that matches your application to your PC Adapt the configuration as described in the configuration note to your network remember to modify the IP address and copy the modified configuration to a TETP server The SmartNode can now load its configuration from this server Note Note Patton regularly adds new configuration templates to the collection at www patton com voip so if you do not see your application on the CD ROM it may have been added to the website If your application is unique and not covered by any of Patton s configura tion templates you can manually configure the SmartNode instead of load ing a configuration file template In tha
31. d Guide Precautions Notes cautions and warnings which have the following meanings are used throughout this guide to help you become aware of potential problems Warnings are intended to prevent safety hazards that could result in per sonal injury Cautions are intended to prevent situations that could result in property damage or impaired functioning Note A note presents additional information or interesting sidelights important information The alert symbol and IMPORTANT heading calls attention to IMPORTANT ard Strictly follow the instructions to avoid property damage T The alert symbol and CAUTION heading indicate a potential haz The shock hazard symbol and CAUTION heading indicate a IN potential electric shock hazard Strictly follow the instructions to avoid property damage caused by electric shock The alert symbol and WARNING heading indicate a potential safety hazard IN Strictly follow the warning instructions to avoid personal injury shock hazard Strictly follow the warning instructions to avoid injury caused j The shock hazard symbol and WARNING heading indicate a potential electric by electric shock Safety when working with electricity returned to Patton Electronics for repairs or repaired by qualified This device contains no user serviceable parts The equipment shall be A service personnel WARNING standards for the country in which it is to be installed If it is not refer to chapte
32. d internet private enterprises patton products sn49xx 8 1 3 6 1 4 1 1768 100 4 10 8 SN4960 4E96V UI iso org dod internet private enterprises patton products sn49xx 9 1 3 6 1 4 1 1768 100 4 10 9 SN4960 4E120V UI iso org dod internet private enterprises patton products sn49xx 10 1 3 6 1 4 1 1768 100 4 10 10 Note The SysObjectIDs for the SN4960 G SHDSL models are the same as the corresponding non G SHDSL models listed above According to table 13 an SNMP get request to iso org dod internet mgmt mib 2 system sysObjectID of a Smart Node 4960 1E15V UI device reads out a numeric OID of 1 3 6 1 4 1 1768 100 4 10 1 which represents a SmartNode 4960 1E15V UI device The mapping of the sysObjectID to each of the SmartNode model is real ized with the SmartNode product identification MIB SNMPv1 compliant SNMP version 2 SNMPv2 and SNMP The SNMP agent running in SmartWare is SNMP version 1 A version 3 SNMPv3 are not currently supported IMPORTANT Identification of the SmartNode devices via SNMP 54 Appendix C Cabling Chapter contents TER EO UE DLO D core eere recte eem terere cb e En E D ente termes ES AE EE OR ES OE EE IE T T E E E N EE 55 SmartNode 4960 Getting Started Guide C Cabling Introduction This section provides information on the cables used to connect the SmartNode and the interface cards to the existing network infrastructure and to third party products Console The SmartNode can
33. d keywords are grouped in braces and are separated by vertical bars screen Terminal sessions and information the system displays are in screen font node The leading IP address or nodename of a SmartNode is substituted with nede in boldface italic font SN The leading SN on a command line represents the nodename of the SmartNode An hash sign at the beginning of a line indicates a comment line 12 Chapter 1 General information Chapter contents Smar No de A IGOK EI on 14 ST OT T ME UD EO AE EO de 16 A EE ee el ER EE EE EE cir 18 13 SmartNode 4960 Getting Started Guide 1 General information SmartNode 4960 overview The SmartNode 4960 T1 E1 PRI VoIP Router see figure 1 combines IP routing VPN Security and Quality of Service with high quality Voice over IP VoIP delivered on 1 to 4 Primary Rate Interfaces PRI T1 EI This combination allows you to leverage low cost Internet Telephony on existing ISDN Phones and PBX equipment for complete SoHo and branch office voice and data connectivity Figure 1 SmartNode 4960 The SmartNode 4960 series consists of several models They differ in the number of PRI ports and voice chan nels supported All models come equipped with two 10 100 1000Base T Ethernet ports The SmartNode 4960 PRI ports and voice channels are listed in table 2 The SmartNode 4960 G SHDSL models are listed in table 3 Table 2 SmartNode 4960 PRI Ports and Voice Channels
34. e Check if show pppoe detail 3 shows State opened This indicates that the PVC is valid and a that you reached a PPPOE server through it e Check if show ppp networks detail 3 shows State opened for both the LCP and the CHAP sec tion If LCP is not working there is probably no compatible authentication protocol configured Make sure authentication chap and authentication pap are included in the subscriber setup If only CHAP failed there may be an error with the username or password Run the debug command nodet debug dsl setup See table 11 above Troubleshooting DSL Connections 42 Chapter 6 Contacting Patton for assistance Chapter contents lieduion na 44 Contact ee ee ee Ad OE teers ee AR EE UNE ped Dicas 44 Ratton sun mie USA EU ao a 44 Alternate Patton support for Europe Middle East and Africa EMEA o ona 44 Waranty Service and Returned Merchandise Authorizations RMAS nes rester rere CREER TUER E REST 44 KET Ai AE AE ME ELE OER EE PR 44 uto EE SES teen ent ENTER ee REDE HO eens 45 Bus oh oe AE TETTE EROS CT EE RI 45 Rotura tor credit policy por AO AE EA RA AE RE 45 AUT TT ann 45 Shippin T coe e AE RE p Ee deed 45 43 SmartNode 4960 Getting Started Guide 6 Contacting Patton for assistance Introduction This chapter contains the following information e Contact information describes how to contact Patton technical support for assistance Warranty Service and Retu
35. e following sections to change the addresses and network masks Note For configuring the IP address of the integrated WAN interface G SHDSL please refer to Chapter 5 G SHDSL Basic Configuration on page 38 Login To access the SmartNode start the Telnet application Type the default IP address for the router into the address field 192 168 1 1 Accessing your SmartNode via a Telnet session displays the login screen Type the factory default login administrator and leave the password empty Press the Enter key after the password prompt login administrator password lt Enter gt 192 168 1 1 gt After you have successfully logged in you are in the operator execution mode indicated by gt as command line prompt With the commands enable and configure you enter the configuration mode 192 168 1 1 enable 192 168 1 1 configure 192 168 1 1 cfg Changing the WAN IP address Select the context IP mode to configure an IP interface 192 168 1 1 cfg context ip router 192 168 1 1 ctx ip router 2 Configuring the desired IP address 31 SmartNode 4960 Getting Started Guide 4 e Initial configuration Now you can set your IP address and network mask for the interface ETH 0 0 WAN Within this example a network 172 16 1 0 24 address is assumed The IP address in this example is set to 172 16 1 99 you should set this the IP address given to you by your network provider 192 168 1 1 ctx ip router finterface WAN 192 168
36. ee 63 F Enduser TT sas veossassceroctencessctcelseiealtoccestecensersectocsestsacusettncsscsssetseese SESE 65 Table of Contents Summary Table of ECL ERROR QD CC OIL E 3 Table OF Go pac e EE EE beet eo crei PE GTI I EUER TISSU ee ee 4 O oo M x M A B E R EE istinti 8 boute gade RE TEORIA EE DEDISSE sinti 9 Un EE EE AE e 9 vues m AA EA AE AR AE nda e con OR ag a la Ian 9 lac lulu PM E 10 S TEE TT E eE Ea EE R E e E AE EE 10 E ee ee EE AAR iii eni inci lle Lili eer 11 Typoccaphlealivenventions used micia documento RE AE ER TEES 11 Gud con endisse n Tos 11 MG tal KT T E cat Tar E TEEST VEEE SEVES SERERE EENES Ee 13 SE O E IO 14 SmartNode 20 GD rear paneles oeste taedet GR O O ET 16 SmartNode Sesde T De data 18 2 Tad iiti IM o CA UEBER rire cer E OE EH HOHEM 20 Joris per EAM EE 21 Application Edge intelligence of enterprise communication ann 21 Applicacion Mulf service ISON Interner telephony IAD oe EE EE E E 22 SR Sua rede iris lA EE EEE TESSE 24 Benn teel ER o T ER PR EU a a o 25 T M r eee 25 Network inlorno one RE ei ni eri 25 bleek Be ia OG d EE EE DA 25 ME alt be ani on EI nas 25 brun Ci 26 vos qu EE 2 EO EE at autres SR 26 AAA mounta Fequi EIE eo o a EE ater FE EE ee TU ee EE eere 26 Tcstalling the ea rewaye ae AA an a OE Ra EE AE EE EE VO Eu 26 Placing the Smar Node m DE ES EE A OR Ne costae Move eR AE ro 26 MR o eene eee AE EU Ed cu 26 Connscungtbe PRI cu EE E
37. ee eee SEE See DAE Bee Bee Be ee Ee EE RE RE ae Bee ee ee ensem sens ee ee ee se 63 Mis p RC RD EE RE EE N RE 64 F End user license agreement o 65 End User License nt AA OE pero De de a RU RE EE 66 hino m 66 DAD a 66 ME 66 Ed AE P 66 OE TRE D J 66 Navi IM ETE 67 T Other Deenses AAN 67 List of Figures cod EV HAND m e AA A A HA NO dl Cy Mi HS O EES SAN A960 LI OE AE OE UE ET 14 ME EE oe Ee LE OE LE pe dele ME TIME A 16 SmarNode 4960 front panel osse testo nue Seem eR Y RED EE HEES DEER WOES IE MS DUET 18 Edge mielligenee af enterprise communication application cec roo EE a its AE SE AE ER O aoe 21 Internet telephony IAD application DEERE REEDE IE DS e a sae 22 Power LED GmarntNode ACO shown Geta EA EE DE EE A ene E E 28 Connecting the SmaniNederto your laptop PC a ara T Te TE R Sea Pa qe ERG EDE ne CSS 30 Connecting the SmareNo de torte Eve ati oats makes ruentes SEE odes eo 32 Conhguime the G SHUSL cantor PPPoE oues es SEE EE wots US NEMPE DUERME RIS 39 onnet voer alie tial cesan meene DO EE Git RE E GE serene 56 Typical Ethernet straight through cable diagram for 10 100Base T eese mpi HE NE ERR DRA ra ARE as sd Typical Ethernet straight throuchcable diagram tor JODOBSse T ei ae etam clea sito eat
38. en EE wan DI Connecting an E PRI port tan NTI usino rtl enne EE RE SR DR amd E 58 ERR portetossouvetcdbled EE a cea at EDE in 58 Gonnscanga 1 1 PRI porto an NT device ace apra E Sig Go OE E a ES EDE EE OG De E 59 pZ EE ee Cable cai AO AE AA EE IRE DA LU ME OE N Le 59 ETIA 561 RJ 45 G pin port oer bRR T PERROS pos PRE ED ER EAA OES GE GE EE T GE DE ED 61 List of Tables NO 0 N CN VA KR Q N E uem EE hh N DO UL HQ b General conventions A ana ATA 11 SmarNods 4960 PRI Pors and Voice Cannes a O ad 14 SmartNode 4960 models with integrated G SHDSL interface escaner aus E pa ipa sa Ra a 15 Ratel sn e rr AE p ILE LUCA EE T EE 17 SN4960 Brenpand Rear panel LEDS se ER ERA ER peed ce SU ENSE E ERU EIER 19 Sample sl uude a re Dac pr ELEM NR a ER eee yee 25 Factory default DP addressand network mask configuration ses rE owes Ee rt 31 RASC OOO scetur c cct d ca urs RE dc 4l VC channelsimbridedd Ethemet mauler SEER O OS AE SERE USE ERIS 4l PVG channels in PPPOE Mods EE se REDE MES RE SA eo SEND NER UE SEE NE MER ERES 4l IR is osa pes ER OI EE OO AN EE EE tees 42 GSHIDSL Dausliter Card Specifications sees verset Reb pi DEE DS OOS ER DES RS EE 53 SmarcNode Models aud their Unique T DIE AE ER ete e EE Ee EE 54 Pi oc MO OD EP EE ee EA M MU tec a T M 61 EES ole OE Ed dere e t ctf E EUM dM OR 62 ESS ERRE RA EO EO OR EA 62 Re AE cce Lem EE ER AA EE ee e ee 62 About this guide This guide describes the SmartNode 4960 hardware instal
39. gh cables for host or hub switch connections see figure 7 LAN connect to ETH 0 1 Ethernet Laptop PC Figure 7 Connecting the SmartNode to your laptop PC The SmartNode comes with a built in DHCP server to simplify configuration Therefore to automatically configure the PC for IP connectivity to the SmartNode the laptop PC must be configured for DHCP The SmartNode will provide the PC with an IP address You can check the connection to the SmartNode by exe cuting the ping command from the PC command window as follows ping 192 168 1 1 Introduction 30 SmartNode 4960 Getting Started Guide 4 e Initial configuration 2 Configuring the desired IP address Factory default IP settings The factory default configuration for the Ethernet interface IP addresses and network masks are listed in table 7 Both Ethernet interfaces are activated upon power up LAN interface ETH 0 1 LAN provides a default DHCP server the WAN interface uses DHCP client to automatically assign the IP address and network mask Table 7 Factory default IP address and network mask configuration IP Address Network Mask WAN interface Ethernet O ETH 0 0 DHCP DHCP LAN interface Ethernet 1 ETH 0 1 192 168 1 1 255 255 255 0 DHCP address range 192 168 1 10 192 168 1 99 255 255 255 0 If these addresses match with those of your network go to section 3 Connecting the SmartNode to the net work on page 32 Otherwise refer to th
40. iagram for 1000Base T Ethernet 57 SmartNode 4960 Getting Started Guide C Cabling E1 PRI The E1 PRI is usually connected to a PBX or switch local exchange LE Type and pin outs of these devices vary depending on the manufacturer In most cases a straight through RJ 45 to RJ 45 can be used to connect the PRI with a PBX A cross over cable is required to connect to an NT device as illustrated in figure 13 on page 58 cable detach the end away from the SmartNode or interface card first to avoid possible electric shock Network hazardous voltages may be present on the WARNING device in the area of the PRI port regardless of when power is turned OFF T Hazardous network voltages are present in the PRI cables If you detach the To prevent damage to the system make certain you connect the A PRI cable to the PRI port only and not to any other RJ 45 socket WARNING Cross over cable Figure 13 Connecting an El PRI port to an NT RJ 48C male RJ 48C male RX Ring 1 1 RX Ring RX Tip 2 2 RXTip RX Shield 3 3 RXShield TX Ring 4 4 TXRing TX Tip 5 5 KTip TX Shield 6 6 TY Shield N C 7 7 M N C 8 8 NC N C No connection Figure 14 E1 PRI port crossover cable E1 PRI 58 SmartNode 4960 Getting Started Guide C Cabling T1 PRI The T1 PRI is usually connected to a PBX or switch local exchange LE Type and pin outs of these devices vary depending on the manufacturer In most cases a straight through RJ 45
41. in session MyISP i i Subscriber PPP L MySubscriber WAN interface context ip Figure 9 Configuring the G SHDSL card for PPPoE 192 0 2 0 24 SmartNodes with built in modems cannot use this subnet in any other way T The Modem setup uses IP messages within its own subnet CAUTION Note For information about the specifications of the G SHDSL daughter card see Appendix B Specifications on page 49 Line Setup There is no line modulation setting The modems automatically adapt to the bit rate and modulation used The status LED on the back of the device is blinking while the modem attempts to connect and lit when the link is established If the modem keeps blinking check the cabling Configuring PPPoE Figure 9 explains how to configure PPPoE on the SmartNodes built in G SHDSL card To configure the DSL port for PPPoE first you need to log in to the SmartNode via the CLI and enter configuration mode login administrator password enter SN4xxx gt enable SN4xxx gt configure Introduction 39 SmartNode 4960 Getting Started Guide 5 G SHDSL Basic Configuration Next you will need to create a WAN profile create a WAN interface and create a subscriber Then you can configure the DSL port port dsl 0 0 for PPPoE Follow this example profile napt WAN context ip router interface WAN ipaddress unnumbered point to point use profile napt WAN tcp adjust mss rx mtu tcp adjust mss tx mtu subscriber p
42. is equipment for repair or warranty information please contact our company If the equipment is causing harm to the telephone network the telephone company may request that you dis connect the equipment until the problem is resolved Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications This is confirmed by the registration number The abbreviation IC before the registration number signifies that regis tration was performed based on a Declaration of Conformity indicating that Industry Canada technical speci fications were met It does not imply that Industry Canada approved the equipment This Declaration of Conformity means that the equipment meets certain telecommunications network protec tive operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be con nected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of certified connector assembly teleph
43. lation and basic configuration For detailed software configuration information refer to the Smart Ware Software Configuration Guide and the available Configura tion Notes Audience This guide is intended for the following users Operators Installers Maintenance technicians Structure This guide contains the following chapters and appendices e Chapter 1 on page 13 provides information about router features and capabilities e Chapter 2 on page 20 contains an overview describing router operation and applications Chapter 3 on page 24 provides hardware installation procedures Chapter 4 on page 29 provides quick start procedures for configuring the SmartNode router e Chapter 5 on page 38 provides information on G SHDSL basic configuration Chapter 6 on page 43 contains information on contacting Patton technical support for assistance Appendix A on page 46 contains compliance information for the router Appendix B on page 49 contains specifications for the routers Appendix C on page 55 provides cable recommendations e Appendix D on page 60 describes the router ports and pin outs Appendix E on page 63 lists the factory configuration settings for SmartNode 4960 Appendix F on page 65 provides license information that describes acceptable usage of the software pro vided with the SmartNode 4960 For best results read the contents of this guide before you install the router SmartNode 4960 Getting Starte
44. nd of the AC power to the mains port see figure 2 on page 16 input voltage from 100 to 240 VAC 50 60 Hz Verify that the proper voltage is present before plugging the power cord into the receptacle Failure to do so could result in equipment damage The internal power supply automatically adjusts to accept an CAUTION 2 Verify that the AC power cord included with your router is compatible with local standards If it is not refer to Contacting Patton for assistance on page 43 to find out how to replace it with a compatible power cord 3 Connect the male end of the AC power cord to an appropriate AC power outlet PRTTUE SmartNode 4960 VoIP IAD T1 E1 PRI Media Gateway Router Ethernet 00 P Ethemet 0 1 SE od d Su 2 sele good CLES o o ooo Ses 6 GAAR Power Figure 6 Power LED SmartNode 4960 shown 4 Verify that the green Power LED is lit see figure 6 Installing the gateway router 28 Chapter 4 Initial configuration Chapter contents DEE M E no 30 1 Consecune the Smart Node your laptop DC reed ER RE Ee Ee E OEC RUE E ee ada 30 PNEU the US Ma RTI 31 Bede ui BD EE E rd E 31 IF EE ol Chatenet dr ED N Re EE DR eU PR EU 31 4 Connecting the Smart ode ta tie n AE AA eI EREMO UI EE EUER 32 ee dig tos configura DEON EA EER eie a ED eed ER AG 33 Boofleader nin MA AE IEEE 34 Start Bootloader ca AA AI idea 34 Start up o ja crop CODI AO cote IO RI n 34 Load amew application image Smart wore
45. one extension cord The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations Repairs to some certified equipment should be made by an authorized maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment mal functions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the ground connections of the power utility telephone lines and internal metallic water pipe system are connected together This protection may be particularly important in rural areas CE Declaration of Conformity This equipment conforms to the requirements of Council Directive 1999 5 EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec ognition of their conformity The safety advice in the documentation accompanying this product shall be obeyed The conformity to the above directive is indicated by CE sign on the device The signed Declaration of Conformity can be downloaded at www patton com certifications Industry Canada Notice 48 Appendix B Specifications Chapter contents S TE 50 buch de M ERE 50 BEL comun L so EE 50 Voice processe smal iS dependent etre dee ee JR REU EE E 50 Fax and modem sSHBDOFE eee a 51 Morcsaienallinte AR OR oo Menu DET e TS
46. only the Ethernet interface 0 0 is available The Boot loader applies the IP address subnet mask and default gateway that were last configured by the Bootloader itself or by another application e g Smart Ware If an application configured the Ethernet interface 0 0 to use DHCP the Bootloader will also use DHCP to learn the interface configuration It can receive and apply the IP address subnet mask default gateway and default TETP server transmitted as basic DHCP information Next server IP address Note This procedure does not download the respective CLI description file Download it after starting up SmartWare with the following command copy tftp tftp server address gt lt server path gt b1 flash Example Downloading and storing a new application image SmartWare RedBoot ip 1 172 16 40 98 19 RedBoot ip g 172 16 32 1 RedBoot ping h 172 16 32 100 Network PING from 172 16 40 98 to 172 16 32 100 pm PING received 10 of 10 expected RedBoot load r v h 172 16 32 100 b 0x1800100 Sn4xxx image bin Bootloader 35 SmartNode 4960 Getting Started Guide 4 Initial configuration Using default protocol TFTP Raw file loaded 0x01800100 0x0199ca6b 1689964 bytes assumed entry at 0x01800100 RedBoot fis delete n 1 Delete image 1 continue y n y Erase from 0x60030000 0x601cc974 cc eet n n n RedBoot fis create Use address 0x01800100 size 1684402 continue y n
47. party D Should End User transfer title of the Designated Equipment to a third party after entering into this license agreement End User is obligated to inform the third party in writing that a separate End User License Agreement from Patton Electronics Company is required to operate the Designated Equipment 5 Warranty The Program s are provided as is without warranty of any kind Patton Electronics Company and its licensors disclaim all warranties either express or implied including but not limited to the implied warranties of mer chantability fitness for a particular purpose or non infringement In no event shall Patton Electronics Com pany or its licensors be liable for any damages whatsoever including without limitation damages for loss of business profits business interruption loss of business information or other pecuniary loss arising out of the use of or inability to use the Program s even if Patton Electronics Company has been advised of the possibil ity of such damages Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages the above limitation may not apply to you End User License Agreement 66 SmartNode 4960 Getting Started Guide F End user license agreement If the Program s are acquired by or on behalf of a unit or agency of the United States Government the Gov ernment agrees that such Program s are commercial computer sofiware or computer software doc
48. pp MySubscriber dial out authentication chap identification outbound username password password bind interface WAN router port dsl 0 0 pvc vpi 8 vci 35 pppoe session MyISP bind subscriber MySubscriber no shutdown The line use profile napt WAN defines that the NAPT profile profile will be used on the ip interface name For PPPoE you will only use outbound for identification You will want to use authentication which is why you bind to a subscriber You can use authentication chap or authentication pap The line bind sub scriber MySubscriber binds the PPPoE session to the PPP subscriber in case authentication is required If you do not use authentication then you will not have a subscriber and you will bind directly to the interface Configuration Summary The modems offer multiple bridged Ethernet connections through logical channels within the DSL link A logical connection is called a Permanent Virtual Circuit PVC and is identified by a VPI VCI number pair Consult your provider s configuration instructions for connections used on your DSL link You define those PVCs inside port dsl 0 0 port dsl 0 0 pvc vpi 8 vci 35 lin the mode pvc you define what to do with the bridged Ethernet connection it offers Bind one or more IP interfaces when your providers uses fixed ip addresses or DHCP in the network Enter PPPoE mode and define a PPP session if the provider is using PPPOE Note PPPoA is not su
49. pported Configuration Summary 40 SmartNode 4960 Getting Started Guide 5 G SHDSL Basic Configuration Setting up permanent virtual circuits PVC The modems currently available are using ATM to multiplex traffic over the DSL framing connection ATM allows you to have separate logical connections running in parallel Those connections are called permanent virtual circuits PVC All permanent virtual circuits use AALS framing Step 1 Table 8 PVC Commands Command node prt dsl 0 0 no pvc vpi 8 vci 35 Purpose Creates PVC 8 35 and enters configuration mode for this PVC The no variant deletes the PVC configuration Step 2 node pvc 8 35 encapsulation fllc ve Sets the encapsulation to be used Optionally select either LLC encapsulation or VC multiplex ing for this PVC Default llc Using PVC channels in bridged Ethernet mode The PVC offers a bridged Ethernet connection as specified in RFC1483 which can be used as an IP link e g with DHCP to assign the address DNS server and default gateway To do this you bind an IP interface to the PVC like it would be done to a normal Ethernet port Table 9 PVC channels in bridged Ethernet mode Command Step 1 node pvc vpi vci no bind interface Associates an IP interface configuration with this lt if name gt Purpose Using PVC channels with PPPoE The RFC1483 bridged Ethernet connection can also be used for PPPoE To do thi
50. pter 3 SmartNode installation Chapter contents bl name toes neel N aac t 25 Mic PRIEST 25 Met oe ialo HOU M M ER ED EE en 25 Denon aou eee reet te AR RR p nere E ey 25 DP related mfontmation center RA AA RA RR RS 25 Soltware tale EN EE AE desides eei du itur 26 Ed ss AE nee SD RG ee ata 26 lese ener dn TCU I OR OE ER EE RE 26 Installing the de AE EA RUBBER oie ii ee eer ee 26 Racine de Sparte ee ER entes ne te Rato E ie i Ee 26 Dusculing cables a err Mee E 26 Connecting the PRI EA e UAE alnie p Connecting the 10101001000 kase T Echerner LAN and WAN cables erret p Installing che DSL WAN cable AE EE py Connecting he PONE i Oe M RA oe 28 24 SmartNode 4960 Getting Started Guide 3 SmartNode installation Planning the installation Before installing the gateway router device the following tasks should be completed Create a network diagram see section Network information on page 25 Gather IP related information see section IP related information on page 25 for more information Install the hardware and software needed to configure the SmartNode See section Software tools on page 26 Verify power source reliability see section Power source on page 26 pag After you have finished preparing for gateway router installation go to section Installing the gateway router on page 26 to install the device Site log Patton recommends that you maintain a site log to record all actions relevant to the s
51. r Chapter 6 Contacting Patton for assistance on page 43 for WARNING help in replacing it with a compliant cable T Ensure that the power cable shipped with this devise meets all applicable 10 SmartNode 4960 Getting Started Guide systems without a power switch line voltages are present within the power supply when the power cords are connected The mains outlet that is utilized WARNING to power the device shall be within 10 feet 3 meters of the device shall be easily accessible grounded and protected by a circuit breaker T Mains Voltage Do not open the case when the power cord is attached For power to the SmartNode is ON or OFF To avoid electric shock use caution when near WAN ports When detaching cables detach the end away from the WARNING SmartNode first j Hazardous network voltages are present in WAN ports regardless of whether Do not work on the system or connect or disconnect cables during periods of IN lightning activity ensure that at end of life you separate this product from other waste and scrap and deliver to the WEEE collection system in In accordance with the requirements of council directive 2002 Y 96 EC on Waste of Electrical and Electronic Equipment WEEE E your country for recycling General observations Clean the case with a soft slightly moist anti static cloth Place the unit on a flat surface and ensure free air circulation Avoid exposing the unit to direct sunlight and other he
52. r H 323 based telephony services IP addresses of central TFTP server used for configuration upload and download optional Software tools You will need a PC or equivalent with Windows Telnet or a program such as Tera Term Pro Web included on the SmartNode CD ROM to configure the software on your SmartNode router Power source If you suspect that your AC power is not reliable for example if room lights flicker often or there is machinery with large motors nearby have a qualified professional test the power Patton recommends that you include an uninterruptible power supply UPS in the installation to ensure that VoIP service is not impaired if the power fails Location and mounting requirements The SmartNode router is intended to be placed on a desktop or similar sturdy flat surface that offers easy access to the cables Allow sufficient space at the rear of the chassis for cable connections Additionally you should consider the need to access the unit for future upgrades and maintenance Note Under the rack mount option the chassis can be equipped with rack mount ears that allow for use in a 19 rack Installing the gateway router SmartNode hardware installation consists of the following e Placing the device at the desired installation location see section Placing the SmartNode on page 26 Connecting the interface and power cables see section Installing cables When you finish installing the SmartNode go to
53. re orienting the receiving antenna and or plugging the receiving equipment into a different AC outlet such that the computing equipment and receiver are on different branches FCC Part 68 ACTA Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA On the bottom side of this equipment is a label that contains among other information a product identifier in the format US AAAEQ TXXXxX If requested this number must be provided to the telephone company The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isnt practical the telephone Compliance 47 SmartNode 4960 Getting Started Guide A Compliance information company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service If trouble is experienced with th
54. rned Merchandise Authorizations RMAs contains information about the warranty and obtaining a return merchandise authorization RMA Contact information Patton Electronics offers a wide array of free technical services If you have questions about any of our other products we recommend you begin your search for answers by using our technical knowledge base Here we have gathered together many of the more commonly asked questions and compiled them into a searchable database to help you quickly solve your problems Patton support headquarters in the USA Online support available at www patton com E mail support e mail sent to support patton com will be answered within 1 business day Telephone support standard telephone support is available five days a week from 8 00 am to 5 00 pm EST 1300 to 2200 UTC GMT ty calling 1 301 975 1007 Fax 1 253 663 5693 Alternate Patton support for Europe Middle East and Africa EMEA Online support available at www patton inalp com e E mail support e mail sent to support patton inalp com will be answered within 1 business day Telephone support standard telephone support is available five days a week from 8 00 am to 5 00 pm CET 0900 to 1800 UTC GMT by calling 41 0 31 985 25 55 e Fax 41 0 31 985 25 26 Warranty Service and Returned Merchandise Authorizations RMAs Patton Electronics is an ISO 9001 certified manufacturer and our products are carefully tes
55. s you enter PPPoE mode within the PVC mode All PPPoE commands apply as if the PVC was a regular Ethernet port Step 1 Table 10 PVC channels in PPPoE mode Command node pvc vpi vci pppoe Purpose Enters PPPoE configuration mode for this PVC Step 2 node pppoe session lt name gt Defines a PPPoE session Step 3 node session lt name gt bind sub scriber lt subscriber name gt Links the session to a subscriber definition Step 4 node session lt name gt no shutdown Enables the PPPoE session Note The bridged PVC connections are internally mapped to VLANs on a virtual Ethernet port 0 2 You will therefore see references to this third Ethernet port when displaying PPPoE status information or debug logs Setting up permanent virtual circuits PVC 41 SmartNode 4960 Getting Started Guide 5 G SHDSL Basic Configuration Diagnostics Table 11 Diagnostics commans Command Purpose Step 1 node gt show dsl type Displays the type of modem installed Step 2 nodes show dsl line state Displays information about the state of the DSL link Step 3 nodes show dsl version Display firmware version information for the modem Step 4 node debug dsl setup Lists the configuration interactions between the gateway and the modem module Troubleshooting DSL Connections Link State e Verify that the DSL link is established status LED is continuously on PPPoE access
56. s the downloaded application image to the permanent memory flash Reply with y to the confirmation request 7 RedBoot gt fis list Checks whether the image has been successfully stored whether it is the desired Release and Build and whether it is valid Bootloader 36 SmartNode 4960 Getting Started Guide 4 e Initial configuration Command Purpose RedBoot go Starts the application image that was downloaded to the vola tile memory RAM Note This type of download takes about 25 minutes since it uses a serial link at only 9600 bps Additional information For detailed information about configuring and operating guidance set up procedures and troubleshooting refer to the SmartNode Series SmartWare Software Configuration Guide on the CD ROM Additional information 37 Chapter 5 G SHDSL Basic Configuration Chapter contents Bote RE EA EA EE E EU RE DD DUC RE sees R TRT O nn REGION SA ES EE EE Setting up permanent vittualeitcuits PNO cerent sess Ge TRU BE EP nda E Ee eek edes Usina PVC channelsum bridged Ethernet mode ee ER Ee Eno Usine INE channels mat PPPOE correnti Oe ER EO AR ER tese vied Troubleshooting DSL Comares 38 SmartNode 4960 Getting Started Guide 5 G SHDSL Basic Configuration Introduction The SN4960 model has an option for a built in G SHDSL modem The modem appears in the configuration as port dsl 0 0 mode port di 0 0 pvc vpi8 vi 35 j
57. stem debug bootstrap environment from Red Hat distributed to you pursuant to the eCos license terms http ecos sourceware org license overview html and GNU General Public License GPL terms http www gnu org copyleft gpl html Source code is available upon request End User License Agreement 67
58. t case refer to the SmartNode Series SmartWare Software Configuration Guide for information on configuring the SmartNode device In this example we assume the TFTP server on the host with the IP address 172 16 1 11 and the configuration named SN cfg in the root directory of the TFTP server 172 16 1 99 if ip WAN copy tftp 172 16 1 11 SN cfg startup config Download 100 172 16 1 99 if ip WAN After the SmartNode has been rebooted the new startup configuration will be activated if you want to copy the running configuration to the startup con figuration Since you just downloaded a configuration file to the IMPORTANT startup configuration you must answer this question with NO Otherwise the downloaded configuration will be overwritten and lost When you issue the reload command the SmartNode will ask 4 Loading the configuration optional 33 SmartNode 4960 Getting Started Guide 4 Initial configuration 172 16 1 99 if ip WAN 4 reload Running configuration has been changed Do you want to copy the running config to the startup config Press yes to store no to drop changes no Press yes to restart no to cancel yes The system is going down Bootloader The bootloader ensures that basic operations network access and downloads are possible in case of interrupted or corrupted application image downloads It offers console access to the Bootloader and the capability for downloading applic
59. ted Guide Table of Contents Bi Specifications D 49 ID cri 50 bore MERE 50 Dita con eL nece ep be i irte ds 50 Voice processing signalling dependen ete ERREUR T pan etiem Pio Ee Se ke Rene eil 50 Fagand modem SUPPONE iia a entro tetro e iier e rat ilari 51 Voicesighallino OE RE EE OR OE RE EN 51 Voice toutimp session deus N 51 DID e mH 52 H ET 52 K PPP ETRE odens 5 52 X H 52 GGEDSL Dauphrer Card GF applicable eee pd etre rte erret reed be nae rte ost taedet pad 53 Identification of the SmartNode devices via SINMD e teen ve enti re ePi 54 exe nn n 55 TA OU T AE EE EE OE OE 56 Won EE EA EE EE ERG OE EE ER 56 IE Et SE EE N RA TE E 57 BEE EL EE OE RE AO AE EE EF 58 QUE 59 D Port pinouts osociriroreiini i EEEE SENEN 60 T arci anale iaia 61 Console pollici aeree i io i e el ee 61 2 a 61 PRI ports caio onto atuial 62 SED IS M au 62 E SmartNode 4960 factory configuration eere es
60. ted before ship ment All of our products are backed by a comprehensive warranty program Note Ifyou purchased your equipment from a Patton Electronics reseller ask your reseller how you should proceed with warranty service It is often more con venient for you to work with your local reseller to obtain a replacement Patton services our products no matter how you acquired them Warranty coverage Our products are under warranty to be free from defects and we will at our option repair or replace the prod uct should it fail within one year from the first date of shipment Our warranty is limited to defects in work manship or materials and does not cover customer damage lightning or power surge damage abuse or unauthorized modification Introduction 44 SmartNode 4960 Getting Started Guide 6 Contacting Patton for assistance Outofwarranty service Patton services what we sell no matter how you acquired it including malfunctioning products that are no longer under warranty Our products have a flat fee for repairs Units damaged by lightning or other catastro phes may require replacement Returns for credit Customer satisfaction is important to us therefore any product may be returned with authorization within 30 days from the shipment date for a full credit of the purchase price If you have ordered the wrong equipment or you are dissatisfied in any way please contact us to request an RMA number to accept your return Patton is
61. to RJ 45 can be used to connect the PRI with a PBX A cross over cable is required to connect to an NT device as illustrated in figure 15 on page 59 cable detach the end away from the SmartNode or interface card first to avoid possible electric shock Network hazardous voltages may be present on the WARNING device in the area of the PRI port regardless of when power is turned OFF T Hazardous network voltages are present in the PRI cables If you detach the To prevent damage to the system make certain you connect the A PRI cable to the PRI port only and not to any other RJ 45 socket WARNING Cross over cable Figure 15 Connecting a T1 PRI port to an NT device RJ 45 male RJ 45 male RX Ring 1 1 RX Ring RX Tip 2 2 RXTip RX Shield 3 3 RX Shield TX Ring 4 4 TXRing TX Tip 5 5 TXTip TX Shield 6 6 TXShield N C 7 7 NC N C 8 8 NC N C No connection Figure 16 T1 PRI crossover cable T1 PRI 59 Appendix D Port pin outs Chapter contents ke SEE reno 61 ON 61 A eer e ee M e e RM E E A 61 PREPO ras 62 GS HDSL POR eene URBE Ee ee EE ada E NE MEI TT 62 60 SmartNode 4960 Getting Started Guide D Port pin outs Introduction This section provides pin out information for the ports of the SmartNode Console port Configuration settings 9600 bps 8 bits no parity 1 stop bit no flow control 8 RTS N C 1 CI5 VO 6 TD 5 RD 4 56 3 DTR 2 CD N 0 1 DSR 12345678 Pins 1
62. umentation and that absent a written agreement to the contrary the Governments rights with respect to such Program s are limited by the terms of this Agreement pursuant to Federal Acquisition Regulations 12 212 a and or DEARS 227 7202 1 a and or sub paragraphs a through d of the Commercial Computer Software Restricted Rights clause at 48 C ER 52 227 19 of the Federal Acquisition Regulations as applicable 6 Termination A The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program s B Patton Electronics Company may terminate this Agreement should End User violate any of the provi sions of section 4 Grant of License on page 66 C Upon termination for A or B above or the end of the Term End User is required to destroy all copies of the licensed Program s 7 Other licenses The Program may be subject to licenses extended by third parties Accordingly Patton Electronics Company licenses the Programs subject to the terms and conditions dictated by third parties Third party software identi fied to the Programs includes Arouting license is included at no charge MGCP capabilities will require the purchase of an additional license The LGPL Lesser General Public License open source license distributed to you pursuant to the LGPL license terms http www gnu org licenses lgpl html e RedBoot Red Hat Embedded Debug and Bootstrap embedded sy
63. via TRIP Ee RE ES ar a Sie paso ee EE NHIEU 34 Load anew application image Smart Ware via the senal Dak coe EE eee ES 36 Additional IRIOEDROD s eee ES UO i RAG ter RHENO ERRORS EE 37 29 SmartNode 4960 Getting Started Guide 4 Initial configuration Introduction This chapter leads you through the basic steps to set up a new SmartNode and to download a configuration Setting up a new SmartNode consists of the following main steps Note If you havent already installed the SmartNode refer to chapter 3 SmartNode installation on page 24 Connecting the SmartNode to your laptop PC Configuring the desired IP address Connecting the SmartNode to the network Loading the configuration optional Note The SmartNode CD ROM contains a collection of third party software tools including TFTP servers and Telnet utilities to help you configure operate and monitor the SmartNode device 1 Connecting the SmartNode to your laptop PC First the SmartNode must be connected to the mains power supply with the power cable Wait until the Power LED stops blinking and stays lit constantly Now the SmartNode is ready and shall be rated for the proper application with respect to volt age current anticipated temperature flammability and CAUTION mechanical serviceability The interconnecting cables shall be acceptable for external use The SmartNode 4960 Series is equipped with Auto MDX Ethernet ports so you can use straight throu
64. ystem if you do not already keep such a log Site log entries should include information such as listed in table 6 Table 6 Sample site log entries Entry Description Installation Make a copy of the installation checklist and insert it into the site log Upgrades and maintenance Use the site log to record ongoing maintenance and expansion history Configuration changes Record all changes and the reasons for them Maintenance Schedules requirements and procedures performed Comments Notes and problems Software Changes and updates to SmartWare software Network information Network connection considerations that you should take into account for planning are provided for several types of network interfaces are described in the following sections Network Diagram Draw a network overview diagram that displays all neighboring IP nodes connected elements and telephony components IP related information Before you can set up the basic IP connectivity for your SmartNode 4960 you should have the following infor mation IP addresses used for Ethernet LAN and WAN ports e Subnet mask used for Ethernet LAN and WAN ports Planning the installation 25 SmartNode 4960 Getting Started Guide 3 SmartNode installation IP addresses of central H 323 gatekeeper if used IP addresses and or URL of SIP servers or Internet telephony services if used Login and password for PPPoE Access Login and password for SIP o

Patton electronic SmartNode 4960 Series User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents