Patton electronic DIAMONDLINK 3201 User's Manual
Contents
1. PATTUN gm rz HE Electronics To DiamondLink Model 3201 amp 3241 G SHDSL Router Quick Start Guide Power Console Ethernet DiamondLink ul PATTON UNSL Router TE m Model 3201 G SPDS Electronics To c gt P d Ca AG Ss 2 SE I V 0 Important This is a Class device and is intended for use in a light industrial environment It is not intended nor approved for use in an industrial or residential environment Document Number 03321U7 001 Rev B Sales Office 1 301 975 1000 Part Number 07M3201 QS Technical Support 1 301 975 1007 E mail support patton com Revised October 15 2008 WWW www patton com This device contains no user serviceable parts The equipment A shall be returned to Patton Electronics for repairs or repaired by qualified service personnel WARNING The external power adapter shall be a listed Limited Power Source The mains outlet that is utilized to power the devise shall be within 10 feet 3 meters of the device shall be easily accessible and protected by a circuit breaker e f an AC power adapter is used ensure that the power cable used meets all applicable standards for the country in which it is to be installed and that it is connected to a wall outlet which has earth ground Hazardous network voltages are present in WAN ports regard less of whether power to the unit is ON or OFF To avoid electric shock use caution when near WAN ports When detaching the2. cables detach the end away from the device first e Do not work on the system or connect or disconnect cables during periods of lightning activity 1 0 Power up the router the proper application with respect to voltage current anticipated temperature flam mability and mechanical serviceability The interconnecting cables shall be acceptable for external use and shall be rated for CAUTION Your G SHDSL router comes with one of the following power supply options e External AC adaptor with included power cord e External DC power supply 1 1 Models with external AC adaptor 1 Connect female plug of the AC power cord to the AC adaptor provided 2 Connect the barrel type connector of the AC adaptor to the Power connector on the DiamondLink router 3 Insert the male plug of the AC power cord into an AC power outlet 100 240 VAC 2 DiamondLink 3201 amp 3241 Quick Start Guide Terminal block Figure 1 48VDC power supply 1 2 Models with external DC power supply l Strip insulation 1 4 inch from the electrical wires that will connect the DC power source to the 48VDC power supply terminal block see figure 1 2 Connect the negative terminal from the power source with to the negative terminal on the power supply 3 Connect the positive terminal from the power source with to the positive terminal on the power supply 4 Connect the 48VDC output barrel type plug to the Power connector on the Diamo
3. ddress for the LAN port according to your network requirements gt ip set interface ipl ipaddress 10 10 10 5 255 255 255 0 Note The above IP address 10 10 10 5 24 is only an example You must choose an IP address on the same subnet as your PC 3 Verify the new address is correct and save it in system boot memory gt ip list interfaces lt enter gt gt system config save lt enter gt 4 DiamondLink 3201 amp 3241 Quick Start Guide 3 0 Connect to the local IP network Now you can connect the DiamondLink to your local IP network and complete the remaining configuration from your PC using a standard web browser Connect the DiamondLink s green Ethernet port to the same Ethernet segment as your PC see figure 3 Press the MDI X switch until the Ethernet Link LED turns on Figure 3 Connecting the DiamondLink to the local IP network You can check the network connection with the ping command For example you would ping 10 10 10 5 from your PC 4 0 Log onto the web management interface You will now access the web management Graphical User Interface GUI to configure the DiamondLink using a standard web browser such as Internet Explorer or Netscape browser 1 At your PC open a web browser and enter the IP address you assigned to the DiamondLink s Ethernet LAN port in step 2 of section 2 2 Modify the IP address on page 4 2 Login to the web management home page using the username superuser and the pa
4. it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service If trouble is experienced with this equipment for repair or warranty information please contact our company If the equipment is causing harm to the telephone network the telephone company may request that you discon nect the equipment until the problem is resolved Connection to party line service is subject to state tariffs Contact the state public utility commission public ser vice commission or corporation commission for information DiamondLink 3201 amp 3241 Quick Start Guide 7 2 3 Industry Canada Notice This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications This is con firmed by the registration number The abbreviation IC before the registration number signifies that registra tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met It does not imply that Industry Canada approved the equipment This Declaration of Conformity means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s sati
5. ndLink 1 3 Power up indication The Power LED blinks as the DiamondLink is powering up When the Power LED stops blinking and remains lit the DiamondLink is ready for you to configure 2 0 Configure the IP address The DiamondLink is shipped with a factory configured IP address assigned to the Ethernet LAN port green out line The address is 192 168 200 10 24 In most cases you must change the address to be on the same subnet as your PC as described in the procedures below If you are not sure which IP address to use for your installa tion contact your network administrator DiamondLink 3201 amp 3241 Quick Start Guide 3 2 1 Connect a PC and login 1 Using the included combination RS232 Ethernet cable and DB9 RJ45 adapter connect a PCs serial port to the on the DiamondLink s red Console port see figure 2 PC with terminal emulator E Serial port Connect to Console port red port Figure 2 Connecting DiamondLink to the PC s serial port 2 Start a HyperTerminal session on the PC using the settings 9600 bps 8 data bits 1 stop bit no parity no flow control 3 Log in to the DiamondLink using the factory default login and password Login superuser Password superuser Login successful 2 2 Modify the IP address 1 Display current IP interface settings for the DiamondLink Ethernet LAN port gt ip list interfaces lt enter gt IP Interfaces ID Name IP Address 2 Modify the IP a
6. phone support e Standard 1 301 975 1007 USA Monday Friday 8 00 am to 5 00 pm EST 1300 to 2200 UTC GMT e Alternate 41 0 31 985 25 55 Switzerland Monday Friday 8 00 am to 5 00 pm CET 0900 to 1800 UTC GMT Fax 1 253 663 5693 USA or 41 0 31 985 25 26 Switzerland 6 DiamondLink 3201 amp 3241 Quick Start Guide B O Compliance Information B 1 Compliance EMC e FCC Part 15 Class A e EN55022 Class A e EN55024 Safety e UL 60950 1 SA C22 2 NO 60950 1 e EC EN60950 e AS NZS 60950 1 PSTN Regulatory e FCC Part 68 e 5 03 e AS ACIF 043 2003 B 2 FCC Part 68 ACTA Statement This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA On the bottom side of this equipment is a label that contains among other information a product identifier in the format US AMEQZZTXXXX If requested this number must be provided to the telephone company The method used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone com pany will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe
7. se Marcham Road Abingdon Oxon 0X14 1UD UK DiamondLink 3201 amp 3241 Quick Start Guide Copyright statement Copyright 2008 Patton Electronics Company All rights reserved The information in this document is subject to change without notice Patton Electronics assumes no liability for errors that may appear in this document Trademarks statement The term Diamondlink is a trademark of Patton Electronics Company All other trademarks presented in this doc ument are the property of their respective owners Warranty Trademark amp Compliance Information For warranty trademark and compliance information refer to the DiamondLink 3201 3241 User Manual located on the CD ROM that came with your router or available online at www patton com Electrical and Electronic Equipment WEEE ensure that at end of life you separate this product from other waste and scrap and deliver to the WEEE collection system in your country for recycling In accordance with the requirements of council directive 2002 96 EC on Waste of BE 10 DiamondLink 3201 amp 3241 Quick Start Guide DiamondLink 3201 amp 3241 Quick Start Guide DiamondLink 3201 amp 3241 Quick Start Guide
8. sfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension cord The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations Repairs to some certified equipment should be made by an authorized maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the ground connections of the power utility telephone lines and internal metallic water pipe system are connected together This protection may be particularly important in rural areas B 4 Radio and TV Interference FCC Part 15 This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television recep tion This equipment has been tested and found to comply with the limits for a Class computing device in accor dance
9. ssword superuser Patton Home Page 7 fal o Home Patton Electronics Company Model 3201 G SHDSL Ho status Router Software gt Quick Start Status of 3201 G SHDSL Router mE System Q E v Configuration DsL Link Status i Normal Operation Fail G SHDSL Status d DSL Link Rate Timeslot 36 r E a i S Local IP Address 192 168 200 144 ction ann 3 Up Time 00 2649s Figure 4 DiamondLink web management home page DiamondLink 3201 amp 3241 Quick Start Guide 5 5 0 Connect the G SHDSL port 1 Obtain single twisted pair cable with an RJ 11 plug connector at each end 2 Plug one end of the cable into the RJ 11socket yellow colored port labeled LINE on the DiamondLink Router 3 Plug the other end of the cable into the RJ 11 wall socket that provides your G SHDSL service 4 When a DSL link is established the front panel WAN Link LED will turn on 6 0 Additional Information Refer to the DiamondLink User Manual located on the CD ROM shipped with your Model 3201 or 3241 and available online at www patton com manuals for detailed information about e Installing configuring operating and troubleshooting e Warranty trademark amp compliance A O Customer and Technical Support Toll Free VolP support call sip support patton com with a VolP SIP phone Online support www patton com E mail support support patton com answered within 1 business day Tele
10. with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection from such interference in a commercial installation However there is no guarantee that interference will not occur in a particular installation If the equipment causes interference to radio or television reception which can be determined by disconnecting the cables try to correct the interference by one or more of the fol lowing measures moving the computing equipment away from the receiver re orienting the receiving antenna and or plugging the receiving equipment into a different AC outlet such that the computing equipment and receiver are on different branches B 5 EC Declaration of Conformity Product Description DiamondLink Models 3201 amp 3241 We certify that the apparatus identified above conforms to the requirements of Council Directive 1999 5 EC on the approximation of the laws of the member states relating to Radio and Telecommunication Terminal Equip ment and the mutual recognition of their conformity The safety advises in the documentation accompanying the products shall be obeyed The C conformity to the above directive is indicated by the CE sign on the device The signed Declaration of Conformity can be downloaded from www patton com certifications 8 DiamondLink 3201 amp 3241 Quick Start Guide B 6 Authorized European Representative DRM Green European Compliance Services Limited Avalon Hou
Download Pdf Manuals
Related Search