Parkside PLS 30 User's Manual
Contents
1. GB IE CY 19 PARKSIDE IAN 33381 KOMPERNASS GMBH Burgstra e 21 D 44867 Bochum by ORFGEN Marketing Last Information Update 06 2009 Ident No PLS30062009 62. SOLDERING GUN WITH HOLDER WI PARKSIDE IE 3 ij GB CED YY Before reading unfold the page containing the illustrations and familiarise yourself with all functions of the device GB IE CY Operation and Safety Notes Table of Content Introduction PrOBERUSE An near Page 7 Features and equipment sse Page 8 Included items 5e eerte eerte eee Page 8 Technical information Page 8 Safety advice 1 Workplace sately 5 oa Deere Page 9 2 Electiicalsalely ted te Page 9 3 Personal safety Page 10 4 Careful handling and use of electrical power tools Page 12 Original accessories Page 13 Before first use Fitting the helical Spring 0 13 Inserting replacing soldering Page 13 Operation Switching on and off Page 14 E 14 Solder sponge Page 14 Soldering 15 Maintenance and Page 15 Service centre Page 16 Warranty esistenti ihe e Page 16 DISS OSE MIN anregt Page 18 Declaration of conformity 19 GB IE CY 5 77 PARKSIDE Introduction The followin
3. e without supervision or in struction by a person responsible for their safety Children must never be allowed to play with the device 10 GB IE CY PARKSIDE b Safety advice Remain alert at all times watch what you are doing and always proceed with caution Do not use the device if you are tired or under the influence of drugs alcohol or medication One moment of carelessness when using the device can lead to serious injury DANGER OF BURNS Never touch the hot soldering A tip or the molten solder You could suffer burn injuries Always let the device cool before you replace components on the device clean it or check its condition After use let the soldering pencil cool down in air only Under no circumstances quench the tip in water CAUTION DANGER OF FIRE Place the soldering pencil down only in the special multifunctional holder or on a fire resistant pad Place the soldering pencil in the multifunctional holder during pauses in your work Keep the device away from combustible material Never leave the device switched on and unattended A CAUTION DANGER OF INJURY Keep your hands away from the hot workpiece The heat from soldering can be conducted through the workpiece For this reason you should use the third hand to hold small workpieces Avoid placing the hot soldering tip in contact with the plastic parts of the multifunctional holder Failure to observe this advice may result in damage to the device If a dange
4. el 0870 787 6177 Fax 0870 787 6168 e mail support uk kompernass com Komperna Service Ireland Tel 1850 930 412 0 082 Min Standard call rates apply Mobile operators may vary e mail support ie kompernass com GB IE CY 17 Disposal Disposal environmentally friendly materials They can be disposed of at your local recycling facility e The packaging and ancillary packing consist wholly of Do not dispose of electrical devices m With the household rubbish In accordance with European Directive 2002 96 EC covering waste electrical and electronic equipment and its transposition into national legislation worn out electrical devices must be collected sep arately and taken for environmentally compatible recycling Contact your local refuse disposal authority for more details of how to dispose of your worn out devices 18 GB IE CY PARKSIDE Declaration of conformity Producer Declaration of conformity Producer C We Komperna GmbH Burgstr 21 D 44867 Bochum Germany hereby declare that this product complies with the following EU directives EU Low Voltage Directive 2006 95 Electromagnetic Compatibility 2004 108 EC Device type description Soldering gun with holder Bochum 30 06 2009 een Hans Komperna Managing Director We reserve the right to make technical modifications in the course of further development
5. g pictograms are used in these operating instructions on the device Read instruction manual Observe caution and safety notes Caution electric shock Danger to life Risk of explosion Risk of fire Warning Hot surfaces Volt AC Watts Effective power Wear a breathing dust mask protective glasses gloves and clothing Keep children away from electrical power tools For indoor use only Check that the device mains lead and plug are in good condition Do not smoke 6 GB IE CY VA PARKSIDE Introduction Y Do not eat Do not drink e Dispose packaging appliance environmentally friendly way Soldering gun with holder Introduction Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle it correctly Please read the operating instructions below Be careful to keep these advice notes and if necessary pass them on to a third party Proper use The device is intended for use soldering electronics and model mak ing Use the device only as described and for the indicated purposes The device is not intended for commercial use Any other use or modifi cation to the device shall be considered as improper use and could give rise to considerable dangers The manvfacturer will not accep
6. ldering grease or soldering fluid as a flux Clean the soldering tip 2 on the moist solder sponge 8 After cleaning the tip 2 it must be tinned coated with solder This is done by melting solder on to the hot soldering tip 2 Guide the soldering tip 2 fo the intended joint site and heat the joint Place the solder with flux between the joint site and the tip 2 to melt it Continue to feed further solder until the whole joint has a covering of solder Then quickly remove the soldering tip in order to avoid overheating the molten solder Allow the solder to harden while not subjecting it to vibration or movement Note The flux is either already contained in the solder or applied separately Ask the advice of the retailer when buying solder in or der to choose the most suitable solder for your intended purpose Maintenance and cleaning VN BLU RISK OF INJURY Before you carry out any work on the device always pull the mains plug out of the mains socket and allow the device to cool GB IE CY 15 77 PARKSIDE Maintenance and cleaning Service centre Warranty o Clean the device after you have finished using it o Usea cloth and a little mild detergent for cleaning the device Inno circumstances use sharp objects or petrol solvents or cleaning agents that might attack plastic Do not allow any liquids to enter the inside of the de
7. lug must not be modified in any way Do not use an adapter plug with devices fitted with a protec tive earth Unmodified plugs and matching sockets reduce the risk of electric shock GB IE CY 9 77 PARKSIDE Safety advice b d e a Keep the device away from rain or moisture Water entering an electrical device increases the risk of electric shock Use a residual current device RCD for protection if operating the electrical power tool in a moist envi ronment is unavoidable The use of an RCD reduces the risk of electric shock 4 Do not use the mains lead for any purpose for which it was not intended e g to carry the device to hang up the device or to pull the mains plug out of the mains socket Keep the mains lead away from heat oil sharp edges or moving parts of the device Damaged or tangled mains leads increase the risk of electric shock Do not operate the device if the mains lead or mains plug is damaged A damaged mains lead presents a serious danger to life from electric shock Always keep the mains lead out of the operating area and run it away from the rear of the device Always pull out the mains plug if you are about to leave the device unattended or wish to carry out any tasks on the device Personal safety Children or persons who lack the knowledge or ex perience to use the device or whose physical sensory or intellectual capacities are limited must never be allowed to use the devic
8. plate Equipment labelled as 230 V may also be used with 220 V Switching on and off Switching on Insert the mains plug into a suitable mains socket Switching off Pull the plug out of the mains socket to switch off the device Third hand CAUTION DANGER OF BURNS The clips 5 on the third hand 6j can become hot while you are soldering the workpiece 1 Fold out the third hand 6 upwards 2 Rotate the clips 5 until they are oriented in the required direction 3 Clamp the workpiece between the two clips 5 Solder sponge A CAUTION The hot soldering tip 2 must never be placed in contact with a dry solder sponge 8 otherwise the solder sponge may be damaged The solder sponge 8 is used to clean soldering tips Moisten the solder sponge 8 before you use it 14 GB IE CY Uhl PARKSIDE o Oo Operation Maintenance and cleaning Soldering The soldering pencil has a rated output of 30 watts and is there fore ideal for electronics soldering The design of the soldering pencil makes it especially suitable for use where access is difficult or for fine soldering work To achieve the best results use electronics solder 1 0 10g elec tronics solder with integrated flux is included or 1 5mm diameter 60 Sn We recommend the use of soldering paste not so
9. rly main tained electrical tools 12 GB IE CY PARKSIDE Safety advice Before first use Original accessories attachments Use only the accessories detailed in the operating instructions The use of attachments or accessories other than those recommended here could lead to you suffering an injury Before first use Fitting the helical spring Insert the narrower end of the helical spring 4 into the opening of the multifunctional holder Ensure that the outwardly bent end of the helix points upwards and insert it into the recess provid ed for it in the multifunctional holder 7 see arrow in Fig C holder 7 in place Push the helical spring 4 into the opening as far as it will go Turn the helical spring 4 clockwise to fix the multifunctional Inserting replacing soldering tips CAUTION DANGER OF BURNS Allow the soldering A pencil to heat up without a soldering tip 1 Insert a soldering tip 2 into the soldering pencil 1 to a depth of half of its shaft length 2 Tighten the clamp screw 3 using a Phillips screwdriver Remove the soldering tip only when the device has been switched off and the soldering tip 2 has cooled Hl PARKSIDE GB IE CY 13 Operation Operation The mains voltage must correspond with that shown on the sander rat ing
10. rous situation arises pull the mains plug immediately out of the mains socket A CAUTION DANGER OF POISONING Do not breathe air contaminated with soldering fumes Q6 When working with the device for long periods do not allow the fumes from soldering to build up They may OD be hazardous to health Always provide adequate GB IE CY 11 Hl PARKSIDE Safety advice ventilation of your working area In addition it is recommended that you wear protective gloves a face mask and a protective apron 8 Do not eat drink or smoke in rooms where soldering is carried out Otherwise your hands may transfer any adhering traces of lead via food or cigarettes into your body m Always wash your hands immediately after soldering m Do not dispose of soldering waste with the household rubbish Soldering waste must disposed of as special waste 4 Careful handling and use of electrical power tools a When not in use always ensure that electrical power tools are kept out of reach of children Do not let any one use the device if he or she is not familiar with it or has not read the instructions and advice Electrical power tools are dangerous when they are used by inexperienced people b Look after the device carefully Check for broken parts or parts that are damaged to the extent they detrimentally affect the functioning of the device Have any damaged parts repaired before you use the device Many accidents have their origins in poo
11. t liability for loss or damage arising from improper use GB IE CY 7 In troduction Features and equipment Soldering pencil Soldering tip Clamp screw Helical spring Clips Third hand Multifunctional holder N Os On amp IS N Solder sponge H Included items Soldering pencil Multifunctional holder Tin solder 10 grams Soldering tips 1x installed Solder sponge Operating instructions Technical information El ectricity supply 230V Frequency 50Hz Power consumption 30W 8 GB IE CY Uhl PARKSIDE Safety advice A Safety advice a b c 2 CAUTION Failure to observe the instructions and advice given below may result in electric shock fire and or serious injury Workplace safety Keep your working area clean and well lit Untidy or poorly lit working areas can lead to accidents Do not work with the device in potentially VA explosive environments in which there are z inflammable liquids gases or dusts Electrical power tools create sparks which can ignite dusts or fumes Keep children and other people away NS while you are operating the electrical tool Distractions can cause you to lose control of the device Electrical safety A To avoid danger to life from electric shock a The mains plug on the device must match the mains sock et The p
12. vice Service centre WN WG Have your device repaired only by qualified specialist personnel using original manu facturer parts only This will ensure that your device remains safe to use If the plug or mains lead needs to be replaced always have the replacement carried out by the manufacturer or his service centre This will ensure that your device remains safe to use Warranty This appliance is guaranteed for 3 years from the date of purchase It has been carefully produced and meti culous ly checked before delivery Please keep your receipt as proof of purchase Contact your service centre by telephone in case of questions pertaining to the warranty Your goods can be transmitted free of cost only in this man ner This warranty applies only to the initial purchaser and is non transferable 16 GB IE CY PARKSIDE Warranty The warranty covers only material or manufacturing faults not normal wear or damage to fragile parts such as switches or rechargeable bat teries The appliance is intended solely for private not commercial use If this product has been subjected to improper or inappropriate handling abuse or interventions not carried out by one of our authorised sales and service outlets the warranty will be considered void This warranty does not affect your statutory rights GB DES Ltd Units 14 15 Bilston Industrial Estate Oxford Street Bilston Great Britain WV14 7EG T
Download Pdf Manuals
Related Search