Panasonic WV-TW310 Installation Guide
Contents
1. Note When using a DHCP server the IP address assigned to the camera can be displayed by click ing the Search button of the IP setting software When a duplicate IP address is used the corresponding camera number will be displayed shaded When the Access Camera button is clicked live images of the selected camera will be dis played It is possible to change the Camera list display between IPv4 addresses and IPv6 addresses in accordance with the protocol in use The information displayed can be sorted by clicking the title of each displayed item Complete each network setup item and click the Save button Network Settings Network Settings StaticiP O DHCP Note O Auto SutolP e In the camera settings Auto IP is deactivated even Port No 80 when it is selected for the connection mode ADS 192 In the camera settings the Primary DNS and Secondary DNS settings are deactivated Subnet Mask Default Gateway DNS Primary DNS Secondary DNS IMPORTANT It may take for about 2 minutes to complete to upload the settings to the camera after clicking the Save button The settings may be invalidated when the LAN cable is disconnected before completing the upload In this case perform the settings again When using a firewall including software allow access to all UDP ports The Wearable Camera Agent Software and Panasonic IP setting software cannot be used on the same PC at the sam2. 14 F to 113 F Note e Locations subject to condensation as the result of severe changes in temperature Shielded STP LAN cables must be used with this unit to ensure compliance with EMC standards E models only Radio disturbance When this product is used near TV radio anten na strong electric field or magnetic field near a motor a transformer or a power line images may be distorted and noise sound may be pro duced PoE Power over Ethernet Use a PoE hub device that is compliant with IEEE802 3af standard Time amp date setting It is necessary to set the time amp date before putting this product into operation Because the time amp date of this product is set to the time and date of the connected computer make sure that the time and date settings of the computer are correct before connecting the camera Major operating controls lt Camera gt WV TW310 Connecting cable Connector Lens cover Mic hole Clip SDHC memory card slot Initial set button REC button Recording start button About the initial set button After turning off the power of the camera while recharging the battery turn on the power of the camera while holding down this button and wait for about 5 seconds or more without releasing this button Wait about 3 minutes after releasing the button The camera will start up and the settings i
3. Wearable Camera Viewer from the presently installed programs and click the Remove button Uninstall the software by following the instructions displayed on the monitor How to operate the Wearable Camera Viewer Software Refer to the WV TW310 Viewer_en chm file for the details 27 Troubleshooting Before asking for repairs check the symptoms with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below A Reference When using DC power supply e Is 12 V DC power supply connected to the power supply terminal Check whether the connection is appropriately established e Is the AC adaptor in use compliant with the Specifications Check the Specifications regarding AC adaptor When using a PoE device for power supply 23 e Are the PoE device and the network connector on the rear of the camera connected using a LAN cable 4 pair Check whether the connection is appropriately established e Depending on the PoE device the power supply will stop when the demanded power exceeds its total power limit for all POE ports gt Refer to the operating instructions of the PoE device in use Power is not turned on Camera search cannot Click Services and Applications select be performed with Wearable Camera Agent under Panasonic IP Setting Services and then right click an
4. card option Manufactured by Panasonic SDHC memory card 32 GB Class 10 1 Refer to Notes on Windows Internet Explorer versions included in the CD ROM for fur ther information about system requirements for a PC and precautions when using Microsoft Windows 7 Microsoft Windows Vista or Internet Explorer 2 When using IPv6 for communication use Microsoft Windows 7 or Microsoft Windows Vista Standard accessories Installation Guide this document Warranty Card e E le o CDROM diia 1 P models only 2 The CD ROM contains the operating instructions and the software Optional accessories WW TB311 Conversion BOX cit acia WW TC312 User License Accessory For H 264 eeren BB HCAS8A P model BB HCA8CE E model Korea 31 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products packaging and or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste For proper treatment recovery and recycling of old products and used batteries please HERE take them to applicable collection points in accordance with your national legislation and the Directives 2002 96 EC and 2006 66 EC By disposing of these products and batteries correctly you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could
5. norma u otro documento normativo siguiendo las estipulaciones de la directiva 2004 108 CE Noi dichiariamo sotto nostra esclusiva responsabilit che il prodotto a cui si riferisce la presente dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle disposizioni della direttiva 2004 108 CE Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende norm of ander normatief dokument overeenkomstig de bepalingen van Richtlijn 2004 108 EC Vi erkleerer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standard eller andre normative dokumenter i folge bestemmelserne i direktiv 2004 108 EC Vi deklarerar harmed vart fulla ansvar for att den produkt till vilken denna deklaration h nvisar r i verensst mmelse med standarddokument eller annat normativt dokument som framst lls i direktiv 2004 108 EC For U S A The model number and serial number of this product may be found on the surface of the unit You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No Ilmoitamme yksinomaisella vastuullamme ett tuote jota tama ilmoitus koskee noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa jotka
6. otherwise arise from inappropriate waste handling For more information about collection and recycling of old products and batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples Cd This symbol might be used in combination with a chemical symbol In this case it complies with the requirement set by the Directive for the chemical involved For U S and Canada For Europe and other countries Panasonic System Communications Panasonic Corporation Company of North America http panasonic net Unit of Panasonic Corporation of North America Importer s name and address to follow EU rules www panasonic com business z For customer support call 1 800 528 6747 Panasonic Testing Centre Three Panasonic Way Secaucus Panasonic Marketing Europe GmbH New Jersey 07094 U S A Winsbergring 15 22525 Hamburg
7. Abbreviations The Wearable Camera is refer to as the camera in this manual Copyright Distributing copying disassembling reverse compiling and reverse engineering of the software provided with this product are all expressly prohibited In addition exporting any software provided with this product violating export laws is prohibited Network security As you will use this unit connected to a network your attention is called to the following security risks Leakage or theft of information through this unit Use of this unit for illegal operations by persons with malicious intent Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks e Use this unit in a network secured by a firewall etc e lf this unit is connected to a network that includes PCs make sure that the system is not infect ed by computer viruses or other malicious entities using a regularly updated anti virus pro gram anti spyware program etc e Protect your network against unauthorized access by restricting users to those who log in with an authorized user name and password e Apply measures such as user authentication to protect your network against leakage or theft of information including image data authentication information user names and passwords e After the unit is accessed by the ad
8. F R Germany Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2012 Cs0212 3042 PGQX1132WA Printed in China
9. ONAL INFORMATION MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM About the stabilization Excessively rough movements during recording reduces the effectiveness of distortion correction About the batteries The capacity of the battery is reduced each time it is used In particular recharging or using the battery in high temperature locations increases deterioration 11 12 Precautions for Installation Panasonic assumes no responsibility for injuries or property damage resulting from fail ures arising out of improper installation or operation inconsistent with this documenta tion Installation place Do not place the unit in the following places e Locations where a chemical agent is used such as a swimming pool e Locations subject to humidity dust steam and oil smoke e Locations in a specific environment where a solvent or a flammable atmosphere exists e Locations where a radiation an X ray a strong radio wave or a strong magnetic field is generated e Locations where corrosive gas is pro duced Locations where it may be dam aged by briny air such as seashores e Locations where the temperature is not within 10 C to 50 C 14 F to 122 F e Locations subject to vibrations This prod uct is not designed for on vehicle use IMPORTANT e When attaching the camera to your body use it environments with ambient tempera tures of 10 C to 45 C
10. Panasonic Installation Guide Wearable Camera moderno WV TW310L WV TW310S WW TW310LEAWW TW310SE Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual WARNING e Batteries battery pack or batteries installed shall not be exposed to excessive heat such as sunlight fire or the like e The installation shall be carried out in accor dance with all applicable installation rules e The connections should comply with local electrical code For WV TB311 Optional 4 Caution Do not open crush disassemble or dispose of batteries in fire with temperatures above 60 C 140 F Mishandling may cause burns fire or explosions Dispose of used batteries according to local ordinances and or regulations For U S and Canada WV TW310L WV TW310S For Europe and other countries WV TW310LE WV TW310SE For Canada This Class A digital apparatus complies with Canadian ICES 003 For U S A NOTE This equipment has been tested and found to comply with the limits for a Class A digi tal device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate rad
11. RY ARISING OUT OF OR RELATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 3 ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER REGARDLESS OF THE CAUSE OF THE MALFUNCTION OR TROUBLE 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REASON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE 7 LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE WV TW310 series Wearable Cameras are battery powered cameras that are used to record images by being worn on a human body They have Fisheye lens which enables shooting with super wide angles It is also possible to record H 264 images on the SDHC memory card of the camera WV TW310 e Image capture size 1280 x 960 Aspect ratio of 4 3 e There are 2 models WW TW310L and VWW TW310S depending on the length of the connecting cable e WV TW210 series includes 2 PC software applications Wearabl
12. age device used with this product may lead to personal information leakage When it is necessary to dispose or give this product to someone even when for repair make sure that there is no data on this product Cleaning this product body Be sure to turn off the power before cleaning Do not use strong abrasive detergent when cleaning this camera Otherwise it may cause discoloration When using a chemical cloth for cleaning read the caution provided with the chemical cloth product Do not touch the lens cover with your bare hands A dirty lens cover causes deterioration of pic ture quality Cleaning the lens cover Use a lens cleaning paper used to clean cam era lenses or lenses of spectacles When using solvent use an alcohols solvent and do not use a thinner or a glass cleaner Transmission interval Image transmission interval may become slow depending on the network environment PC per formance shooting subject access number etc About SDHC memory card e Before inserting the SDHC memory card turn off the power of this product first Otherwise it may cause malfunction or damage data recorded on the SDHC memory card e When using an unformatted SDHC memo ry card format it using this camera Recorded data on the SDHC memory card will be deleted when formatted If an unfor matted SDHC memory card or an SDHC memory card formatted with other devices is used this product may not work properly or performance
13. c from different directions top bottom left or right by changing the direction it is attached to the camera To change the direction of the camera clip loosen the camera clip screws rotate the clip to the desired direction and then retighten the camera clip screws Recommended tightening torque 0 78 N m 0 58 lbf ft Fixing screw for clip 21 Fix the camera to your clothing lt WV TW310L gt lt Front view gt lt Rear view gt Connecting cable Camera Battery container optional lt WV TW310S gt lt Lens angular field of view gt IMPORTANT e Attach the camera so that it is securely fixed e Attaching the camera to loose clothing reduces the effectiveness of distortion correction 22 Connection Caution e ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY or LIMITED POWER SOURCE Before starting the connection turn off the power for this camera and the devices to be connected and then prepare the required devices and cables Connection example when connecting to a network using a PoE hub PoE Hub LAN cable category 5 or better straight STP PC lt Required cable gt LAN cable category 5 or better straight STP E models only IMPORTANT e Use a switching hub or a router which is compliant w
14. d select Software gt Stop After using Panasonic IP Setting 24 Software follow the above procedure to select Wearable Camera Agent and then right click and the select Start 28 Specifications O Basic Power source 12 V DC PoE IEEE802 3af compliant Power consumption 12 V DC 650 mA PoE 11 W Class O device ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY or LIMITED POWER SOURCE Ambient operating temperature 10 C to 50 C 14 F to 122 F In wearing 10 C to 45 C 14 F to 113 F Ambient operating humidity Less than 90 no condensation Continuous operating time Approx 5 hours at normal temperature at the time of purchase when charged fully Battery WV TB311 Lithium ion battery only Dimensions 45 mm W x 75 mm H x 41 mm D 1 25 32 inches W x 2 15 16 inches H x 1 5 8 inches D Excluding the cable and projection Mass WV TW310L Approx 210 g 0 46 lbs WV TW310S Approx 160 g 0 35 lbs Cable Length WV TW310L 950 mm 37 3 8 inches WV TW310S 600 mm 23 5 8 inches Finish Black Camera Image sensor 1 4 type MOS image sensor Effective pixels Approx 1 3 megapixels Scanning area 3 60 mm H x 2 70 mm V 5 32 inches H x 11 100 inches V Scanning system Progressive Minimum illumination Color 1 5 Ix 1 5 footcandl
15. deterioration may be caused Refer to the Operating Instructions included in the CD ROM for how to for mat an SDHC memory card e When some SDHC memory cards are used with this product the product may not work properly or performance deterioration may be caused Use the SDHC memory cards recommended in page 30 e Frequently overwriting the SD memory card reduces its product life It is recommended to replace the SD memory card once a year Contact service personnel for information about replacement SD memory cards About the MOS image sensor e When continuously shooting a bright light source such as a spotlight the color filter of the MOS image sensor may have deteri orated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period the discolor ation may remain e When shooting fast moving subjects objects crossing the shooting area may look to be bending askew AVC Patent Portfolio License THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO i ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD AVC VIDEO AND OR i DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITI
16. e BW _ 1 0 Ix 1 0 footcandle Gain AGC On High On Mid On Low Off Wide dynamic range On Off Adaptive black stretch On Off Back light compensation On Off Light control mode setting Indoor scene 60 Hz 60 Hz ELC Maximum exposure time 1 30 3 100 3 120 2 100 2 120 1 100 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 Day amp Night electrical Off Auto White balance ATW1 ATW2 AWC Digital noise reduction High Low Lens Focal length 0 82 mm Maximum aperture ratio 1 2 6 Angular field of view Horizontal 180 Vertical 140 29 30 O Network Network Resolution 10BASE T 100BASE TX RJ45 connector Aspect ratio 4 3 H 264 1280x960 JPEG 640x480 Only HTML on PC 5 fps Image compression method H 264 Transmission type Unicast Video bit rate 2048 kbps 4096 kbps 8192 kbps Frame rate priority 15 fps 30 fos Audio compression method G 726 ADPCM 32 kbps Protocol IPv6 HTTP FTP IPv4 HTTP FTP DHCP OS 1 2 Browser Microsoft Windows 7 rosoft Windows Vista icrosoft Windows XP SP3 indows Internet Explorer 8 0 82 bit indows Internet Explorer 7 0 82 bit crosoft Internet Explorer 6 0 SP3 c _ INIICTOS OTL NNIICIOWS e999 indows Internet Explorer 9 0 82 bit j hj Maximum concurrent access number 10 at JPEG 4 at H 264 Compatible SDHC memory
17. e Camera Agent Software and Wearable Camera Viewer Software which are in the provided CD ROM WV TB311 Optional e The WV TB311 is the battery container specified for the WV TW310 series WV TC312 Optional e The WV TC312 is the conversion box specified for the WV TW310 series e The WV TC312 is used to connect the camera and PC e The WV TC312 has a 12 V DC input terminal and 10BASE T 100BASE TX PoE input terminal lt System configuration gt Network Camera View 4S e Wearable Camera Agent Software e Wearable Camera Viewer Software PC installed with software Wearable Camera Wearable Camera IMPORTANT e Wearable Camera Agent Software uses directed broadcasts to search for the camera The router that you use must be configured to allow directed broadcast packets If directed broad Cast packets cannot be configured to be allowed structure your system so that camera and the PC installed with software are on the same network segment e Use UDP port 10668 and 10669 for transmissions between the Wearable Camera Agent Software and the camera The router that you use must be configured to allow UDP port 10668 and 10669 Note e It is necessary to configure the network settings of the PC and its network environment to moni tor images from the camera on the PC It is also necessary to install a web browser on the PC H 264 Recording Images are encoded to H 264 and saved on the SDHC memory card Wide angle The wide an
18. e time To use the Panasonic IP setting software on a PC with Wearable Camera Agent Software installed right click My Computer and select Manage to open the Computer Management screen select and right click Wearable Camera Agent from Services and Applications Services and then select Stop After finishing using the Panasonic IP setting software perform the above steps again select and right click Wearable Camera Agent and then select Start 25 26 Installation of Wearable Camera Agent Software Insert the provided CD ROM into the CD ROM drive of your PC Double click Agent_setup exe in the PC_software folder The installer for Wearable Camera Agent Software will start Follow the on screen instructions If the installation is performed with the standard settings a C Panasonic Wearable folder is created and executable files and other files are installed Configure the exceptional settings of Windows Firewall Procedures for Windows XP Click the Security Center on the Control Panel and click Windows Firewall Exceptions tab 2 Click the Add Program button and click the Browse button Select CamManageService exe in the folder C Panasonic Wearable Agent and click the Open button Select CamManageService exe and click the OK button Perform steps to 4 in the same manner to add AgentGui exe Procedures for Windows Vista Open the Security on the Con
19. een instructions to uninstall the program Procedures for Windows 7 Open Programs and Features from Control Panel Programs 2 Select Wearable Camera Agent from the presently installed programs and click the Remove button Uninstall the software by following the instructions displayed on the monitor How to operate the Wearable Camera Agent Software Refer to the WV TW310 Agent_en chm file for the details Installation of Wearable Camera Viewer Software Insert the provided CD ROM into the CD ROM drive of your PC Double click Viewer_setup exe in the PC_software folder The installer for Wearable Camera Viewer Software will start Follow the on screen instructions If the installation is performed with the standard settings a C Panasonic Wearable folder is created and executable files and other files are installed Uninstallation of Wearable Camera Viewer Software Procedures for Windows XP Select Wearable Camera Viewer from Control Panel Add or Remove Programs 2 Click Delete The uninstall program starts Follow the on screen instructions to uninstall the program Procedures for Windows Vista Select Wearable Camera Viewer from Control Panel Programs Uninstall a program 2 Click Uninstall The uninstall program starts Follow the on screen instructions to uninstall the program Procedures for Windows 7 Open Programs and Features from Control Panel Programs 2 Select
20. gle lens enables wide areas to be recorded Pre recording Depending on the settings pre recording of up to 30 seconds is possible Color mode black amp white mode switching available Images will be displayed clearly even at night since the camera will be automatically switched from the color mode to the black and white mode under low illumination condition Power over Ethernet function When connecting with a PoE Power over Ethernet device power will be supplied by simply con necting a LAN cable IEEE802 3af compliant Upload and save the video image data With Wearable Camera Agent Software included in the CD ROM you can upload the video image data from the camera to a PC and save it Combine the multiple video image data With Wearable Camera Agent Software included in the CD ROM you can combine the multiple video image data in MPEGA4 file format Verifying Integrity check With Wearable Camera Agent Software or Wearable Camera Viewer Software included in the CD ROM you can verify the video image data Image correction With Wearable Camera Viewer Software included in the CD ROM you can view the images with stabilization and distortion correction Playback With Wearable Camera Viewer Software included in the CD ROM you can play video images Snapshot With Wearable Camera Viewer Software included in the CD ROM you can take snapshots About the user manuals There are 2 sets of operating instructions for
21. io frequency energy and if not installed and used in accordance with the instruction man ual may cause harmful interference to radio com munications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter ference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment For Europe 4 We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004 108 EC Wir erklaren in alleiniger Verantwortung daf das Produkt auf das sich diese Erklarung bezieht mit der folgenden Norm oder normativen Dokument bereinstimmt Gem den Bestimmungen der Richtlinie 2004 108 EC Nous d clarons sous notre propre responsabilit que le produit auquel se r f re la pr sente d claration est conforme la norme sp cifi e ou tout autre document normatif conform ment aux dispositions de la directive 2004 108 CE Nosotros declaramos bajo nuestra nica responsabilidad que el producto a que hace referencia esta declaraci n est conforme con la
22. ith 10BASE T 100BASE TX e Power supply is required for each camera When using a PoE device hub 12 V DC power supply is unnecessary 23 Configure the network settings Install the software Before installing the software read the readme file on the provided CD ROM first Software included on the provided CD ROM e Panasonic IP setting software Configure the network settings of the camera Refer to the following for further information e Viewer Software Network Camera View 4S It is necessary to install the viewer software Network Camera View 4S to display images on a PC and to setup the Wearable Camera basic configuration Install the viewer software by dou ble clicking the nwcv4Ssetup exe icon on the provided CD ROM Refer to the WV TW310 Operating Instructions included in the CD ROM for more details e Wearable Camera Agent Software It is necessary to install the Wearable Camera Agent Software to upload the video image data from the cameras e Wearable Camera Viewer Software It is necessary to install the Wearable Camera Viewer Software to play the video image data Configure the network settings of the camera using the Panasonic IP setting software It is possible to perform the network settings of the camera using the IP setup software on the pro vided CD ROM When using multiple cameras it is necessary to configure the network settings of each camera independently If the Panasonic IP setting software does not w
23. ministrator make sure to close the browser e Change the administrator password periodically e Do not install the camera in locations where the camera or the cables can be destroyed or damaged by persons with malicious intent 10 Precautions Follow the instructions of battery Use only the WV TB311 battery container optional for the battery In combination with this product refer to the WW TB311 and WV TC312 Operating Instructions for care and handling of the battery charge Stop the operation immediately when something is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product stop the operation immediately and contact your dealer Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Do not insert any foreign objects This could permanently damage the apparatus Turn the power off immediately and contact qualified service personnel for service Do not use this product in an inflammable atmosphere Failure to observe this may cause an explosion resulting in injury Do not install this product in locations subject to vibration Loosening of mounting screws or bolts may cause a fall of the product resulting in injury Do not strike or give a strong shock to this pr
24. ncluding the network settings will be initialized Before initializing the settings it is recommended to write down the settings in advance 13 lt Battery container Optional gt WV TB311 Optional Indicator lamps lt Rear view gt O O OrO PWR REC SD CHG Clip Connector Power button The connector cover of the battery container optional can be opened in the following way and fixed to the side of the battery container optional When storing the battery container optional in the stand open the connector cover and fix it to the side of the battery container optional Connector cover Connector cover Network charge connector About the battery container s indicators The battery container s indicators light as follows according to the status of the camera Understanding how and when the indicators light can help you troubleshoot problems with the camera Slow blinking Fast blinking Light off ON Power OFF ener bat Remaining bat Activating Remaining bat tery time Long tery time Short tery time None Ea imag Recording ee eal recorded data Not recording Pa and audio images ee eal the SD memory card Pre recording SD memory card error Remaining SD Remaining SD The SD memory card is not inserted recording time recording time The SD memory card is l
25. noudattavat direktiivin 2004 108 EC s d ksi Vi erkl rer oss alene ansvarlige for at produktet som denne erkl ringen gjelder for er i overensstemmelse med f lgende norm eller andre normgivende dokumenter som f lger bestemmelsene i direktiv 2004 108 EC Contents Important safety instructions Limitation of liability Ez Disclaimer of Watios es Nea eee een ees es PICTACC EE O a E told E Adah uel O Main functions ii ea a a ee 6 About the User Manual Sucia ile an pie 7 System requirements fOr a PC cecceeeceeeeneeeeeeeeeeeeesaeeeeaeeeeaaeeeaeeeeaeeseaaeeeaaeesaeeeeaeeeeaeeseaeesenaeetae 8 Trademarks and registered trademarKS ccccccceeeeeeeeeeeeneeeeeeeeeeeeeeseceaaaaeeeeeeeeeeeeeeececeaeeeeeeeeeees 9 Abbreviations s 0 a8 225 acta sana li e ee 9 COPY Elia is 9 Network SeCUr Vii dad AEE 9 PISCINAS a a i ee De ee 10 Precautions for Installation ciar tin 12 Major operating controls Wii A a ee a rE 13 Insert remove an SDHC Memory card eeseeeecceeeeeeeeeeeteeeeeeaeeeeaeeseaeeeeaeeeeaeeseaeeseaeeeeaeeseeeeeneaes 17 Installation icecieie siete ad tiene te de ne ee eee d A O narrate Configure the network settings TroubleshootinQ ccccccccnnncnonccccnnnno Specifications eects Standard accessories Optional ACCESSOMES iii edad da Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Foll
26. ocked Long Short There is no remaining memory A read write error has occurred Green Charging CHG Red Charging ot error detected y lt Conversion box Optional gt WV TC312 Optional Conversion box optional Network charge cable Power indicator Network connector Terminals of the 12 V DC IN connector Pinout 1234 anno CAN 2 135050 3 NC 12 V DC IN connector 4 NC 16 The battery container optional and the camera can be stored in the stand mounted to the conver sion box optional With the battery container optional and the camera stored in the stand the conversion box optional can be connected to 12 V DC or a PoE hub making recharging the bat tery container optional possible a LAN cable can also be connected to the conversion box optional making it possible to view saved images on a computer monitor When removing the stand from the conversion box optional lift up the stand while pressing the 4 tabs on the stand at the same time 2 Conversion box optional Insert remove an SDHC memory card IMPORTANT e Contact an authorized service center for information on replacing SDHC memory cards e Before inserting an SDHC memory card turn off the power of the camera first e When inserting an SDHC memory card make sure the direction e When the SDHC memory card is inserted or removed with the power on data in the SDHC memory ca
27. oduct Failure to observe this may cause fire or injury Do not rub the edges of metal parts with your hand Failure to observe this may cause injury Turn the power off when connecting this product Failure to observe this may cause electric shock In addition short circuit may cause fire Do not directly touch the product with your skin when it has been turned on for an extended period Direct skin contact with high temperature parts of the product for extended periods may cause low temperature burns Turn the power off when cleaning of this product Failure to observe this may cause injury Precautions for use To keep on using with stable performance Do not use this camera in hot and humid con ditions for a long time Failure to observe this causes component degradation resulting in life shortening of this product Do not expose this camera to direct heat sources such as a heater Handle this camera with care Do not drop this camera nor apply shock or vibration to this camera Failure to observe this may cause trouble About the PC monitor Displaying the same image on a CRT type monitor for a long time may damage the moni tor It is recommended to use a screen saver When an error is detected this product will restart automatically This product will be inoperable for about 2 minutes after the restart just as when the power is turned on Product disposal transfer Data saved on this product or a stor
28. on box optional to the network charge con nector of the battery container optional Insert the cable into the connector until a click is heard Ensure that they are connected in the correct direction Battery container optional Network charge connector 19 20 Connect the connecting cable of the camera to the connector of the battery container optional Then charging starts _ Connecting cable LAN cable IMPORTANT e Recharging will not begin if the temperature of the internal battery pack is outside of the allow able temperature range 0 C to 50 C 82 F to 122 F e Charging begins automatically when the temperature enters the allowable range e Recharging will stop after 6 hours from when the connection was made Under normal conditions recharging finishes within 3 5 hours e Exposing the battery to high temperatures may cause battery deterioration reduced battery capacity and recharging cycle Note e When the camera is connected to a PoE hub without the battery container optional connected the power indicator of the conversion box optional may blink This is not a malfunction Wearing the camera Attach the battery container optional to the belt you are wearing Belt Battery container optional The camera clip can be attached in 4 directions to the camera depending on where you want to fix the camera The camera clip can be fixed to clothing belts pockets et
29. ork configure the network settings of the camera and the PC individually on the Network page of the setup menu Refer to the Operating Instructions included in the CD ROM for further information IMPORTANT e When using Microsoft Windows 7 or Microsoft Windows Vista the Windows Security Alert window may be displayed when starting the IP setup software In this case disable User Account Control from the control panel e For the security enhancement the MAC address IP address of the camera to be configured will not be displayed when about 20 minutes have passed after turning on the power of the camera When the effective period is set to 20min in the IP setup However cameras in the initial set mode are still displayed even after 20 minutes e Panasonic IP setting software is inoperable in other subnets via the same router When config uring the IP address of the camera for the first time configure the PC s IP address to 192 168 0 xxx e This camera cannot be displayed or set with an older version of the IP setup software version 2 xx Start the Panasonic IP setting software by double clicking the EasylpSetup exe icon on the provided CD ROM e The License Agreement will be displayed Read the Agreement and choose accept the term in the license agreement and click OK Sea a See Click the Network Settings button after select ing the MAC address IP address of the camera g l to be configured E E DUDE
30. ow all instructions 5 Clean only with dry cloth 6 Do not install near any heat sources such as radiators heat registers stoves or other appara tus including amplifiers that produce heat 7 Only use attachments accessories specified by the manufacturer 8 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICA ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR TH IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPECIAL CONSEQUENTIAL OR EXEMPLA
31. rd may be damaged e Do not use other screws to tighten the cover Recommended tightening torque T8 0 2 N m 0 14 lbf ft Remove the memory cover after removing the tamperproof screw of the cover on the WW TW310 and insert the SDHC memory card into the SDHC memory card slot Attach the cover and tighten the tamperproof screw Recommended tightening torque T8 0 2 N m 0 14 lbf ft 17 18 Installation Connecting the battery container optional to the camera Align the direction of the mark on the connector on the end of the connecting cable to the direction of the mark on the battery container optional Insert the connector of the connecting cable straight into the connector of the battery container optional and then lock it by rotating the outer ring of the connecting cable clockwise Battery container optional Rotate clockwise Removing the battery container optional from the camera To remove the camera from the battery container optional unlock the connector by rotating the outer ring counterclockwise and then pull the connecting cable straight Rotate counterclockwise Connecting the conversion box optional to the battery container optional Connect the power to the conversion box optional Connect 12 V DC or PoE hub for the power source Connecting cable Network connector By 7 12V DC IN connector LAN cable Connect the network charge cable of the conversi
32. the WV TW310L WV TW310S P model WV TW31 OLE and WV TW310SE E model e Installation Guide Explains how to install and connect devices e Operating Instructions included in the CD ROM Explains how to perform the settings and how to operate this camera Adobe Reader is required to read these operating instructions on the provided CD ROM When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it The model number is abbreviated in some descriptions in this manual The screens or illustrations used in this manual show the case of WV TW310L P model System requirements for a PC CPU Memory Network Interface Audio interface Monitor OS Web Browser Other IMPORTANT Intel Core 2 Duo 2 66 GHz or faster recommended 2 GB or more 10BASE T 100BASE TX 1 port Sound card when using the audio function Image capture size 1024x768 pixels or more Color 24 bit True color or better Microsoft Windows 7 Microsoft Windows Vista Microsoft Windows XP SP3 Windows Internet Explorer 9 0 32 bit Windows Internet Explorer 8 0 32 bit Windows Internet Explorer 7 0 32 bit Microsoft Internet Explorer 6 0 SP3 CD ROM drive It is necessary to read the operating instructions and use the software on the provided CD ROM DirectX 9 0c or later Adobe Reader It is necessary to view the PDF file on
33. the provided CD ROM e When using a PC that does not meet the above requirements displaying of images may become slower or the web browser may become inoperable e Audio may not be heard if a sound card is not installed on a PC Audio may be interrupted depending on the network environment e Microsoft Windows 7 Starter Microsoft Windows Vista Starter and Microsoft Windows XP Professional 64 bit Edition are not supported e When using IPv6 for communication use Microsoft Windows 7 or Microsoft Windows Vista Note e Refer to Notes on Windows Internet Explorer versions included in the CD ROM for further information about system requirements for a PC and precautions when using Microsoft Windows 7 Microsoft Windows Vista or Internet Explorer Trademarks and registered trademarks e Microsoft Windows Windows Vista Internet Explorer ActiveX and DirectX are either regis tered trademarks or trademarks of Microsoft Corporation in the United States and or other countries e Microsoft product screen shot s reprinted with permission from Microsoft Corporation e Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United States and other countries e Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries e All other trademarks identified herein are the property of their respective owners
34. trol Panel and click the Windows Firewall Allow A Program Through Windows Firewall Exceptions tab 2 Click the Add Program button and click the Browse button Select CamManageService exe in the folder C Panasonic Wearable Agent and click the Open button Select CamManageService exe and click the OK button Perform steps to in the same manner to add AgentGui exe Procedures for Windows 7 Open the System and Security on the Control Panel and click the Windows Firewall Allow A Program Through Windows Firewall 2 Click the Allow Another Program button and click the Browse button Select CamManageService exe in the folder C Panasonic Wearable Agent and click the Open button Select CamManageService exe and click the OK button Perform steps to in the same manner to add AgentGui exe Uninstallation of Wearable Camera Agent Software Note e The data uploaded from the camera will not be deleted even when this software is unin stalled Procedures for Windows XP Select Wearable Camera Agent from Control Panel Add or Remove Programs 2 Click Delete The uninstall program starts Follow the on screen instructions to uninstall the pro gram Procedures for Windows Vista Select Wearable Camera Agent from Control Panel Programs Uninstall a program 2 Click Uninstall The uninstall program starts Follow the on scr
Download Pdf Manuals
Related Search