Panasonic WV-CW334 Operating Instructions
Contents
1. 11 Major operating controls and their functions 13 Dip switch Y Li This illustration shows the camera without the inner dome Q Camera fixing screw 2 Heater output connector P nq Panning table Focus lock knob Zoom lock knob 2 Video output cable Azimuth adjuster cot 4 9 i i Jl Tilting table Tilting lock screw left and right Monitor output connector RCA Panning lock screw LOCK Power cord Supplies 24 V AC or 12 V DC from an external power source 2 Video output cable Transmits composite video signals If this unit is connected to the multiplex unit the multiplexed VD2 that is prioritized over INT is automatically selected Dome cover Panning lock screw LOCK Fixes the panning table Panning table Rotate this table to adjust the panning angle of the camera Tilting table Adjusts the tilting position of the camera Tilting lock screws left and right Fixes the tilting position Azimuth adjuster Adjusts the azimuth angle of the camera Zoom lock knob Fixes the zoom position after adjusting Focus lock knob Fixes the focus position after adjusting 4 Camera fixing screw Fixes the attachment on the camera body 12 Heater output connector Connects to the optional heater unit 13 Dip switch Turns ON OFF the day night mode adap tive black stretch backlight compens2. Mounting base ex N Z oS a F p p o Center of mounting base ANY S Female thread for conduit e ri For use of the hole For use of the hole B 85 mm 138 mm e 3 11 32 inches 5 7 16 inches 138 mm 5 7 16 inshes Note e Only the same type of holes amp or B shall be used for mounting 17 18 Previously run the cables from the wall or ceiling through the cable access hole Mount the attachment onto the mount bracket Recommended tightening torque 0 78 N m 0 58 Ibf ft Note e For wall mounting Installation shall be performed in such a manner that f TOP of the camera attachment faces upward Except for the case of connecting the conduit from the top page 27 For ceiling mounting The front side model number indication face of the camera shall be aligned in the direction of the arrow in LFRONT on the camera attachment e Ensure that any one of the arrows on the mount bracket is aligned with the arrow of f TOP on the attachment Camera installation Mount the camera lt To mount the camera on a two gang junction box gt CD Connect the power cord and the video output cable s page 28 2 Align the OP EN mark of the camera with the protrusion of the camera attachment G Engage the attachment mounting screw of the camera with the camera mounting hole of the camera attachment and rotate the camera i
3. EC en 2004 108 EC Vi erklaerer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standarder eller andre normative dokumenter i folge bestemmelserne i direktivene 2006 95 EC og 2004 108 EC Vi deklarerar h rmed v rt fulla ansvar f r att den produkt till vilken denna deklaration h nvisar r i verensst mmelse med de standarder eller andra normativa dokument som framst lls i direktiv nr 2006 95 EC och 2004 108 EC IImoitamme yksinomaisella vastuullamme ett tuote jota tama ilmoitus koskee noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja jotka noudattavat direktiivien 2006 95 EC ja 2004 108 EC s d ksi Vi erkl rer oss alene ansvarlige for at produktet som denne erkl ringen gjelder for er i overensstemmelse med f lgende normer eller andre normgivende dokumenter som f lger bestemmelsene i direktivene 2006 95 EC og 2004 108 EC Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Clean only with dry cloth 6 Do not block any ventilation openings Install in accordance with the manufacturer s instruc tions 7 Do not install near any heat sources such as radiators heat registers stoves or other appara tus including amplifiers that produce heat 8 Do not defeat the safety purpose of the polarized or grounding t
4. Keep the product out of direct sunlight Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particu lar environment e Make sure that the installation area is strong enough to hold the product such as a concrete ceiling e Install the camera in the foundation area of the architecture or where sufficient strength iS assured f a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced Avoid installing this product in the follow ing locations Locations where a chemical agent is used Such as a swimming pool Locations subject to steam and oil smoke Such as a kitchen Locations near flamma ble gas or vapor Locations where radiation or x ray emis sions are produced e Locations where corrosive gas is pro duced Locations where it may be dam aged by briny air such as seashores Locations where the temperature is not within 10 C to 50 C 14 F to 122 F When using the optional heater unit the product can be used at temperatures with in 30 C to 50 C 22 F to 122 F and humidity below 90 e Locations subject to vibrations This prod uct is not designed for on vehicle use Avoid moist or dusty places to install this system Otherwise lifetime of the internal parts may be shortened Avoid installing the camera in a place with a high level of noise Instal
5. m feet R Resistance of copper wire O m O ft Va DC output voltage of power supply unit DC current consumption A See speci fications Important When using 12 V DC power supply the heater is unavailable 29 Optional Heater Unit WV CW5H option Installing the heater unit enables the camera to operate in a low temperature environment below 30 C 22 F The heater turns on automatically when the temperature inside the camera drops below 10 C 50 F and turns off when the temperature rises A small fan inside the unit will mini mize condensation on the surface of the dome cover caused by changes in ambient temperature unless temperatures change too rapidly Important e When using 12 V DC power supply the optional heater unit is unavailable e Turning the heater on and off may disturb the camera images e The power supply of the camera shall be turned off when mounting or dismounting the heater When servicing pay attention to high temperature on the surface of the heater unit Disconnect the harness and wait until the heater unit cools e When the camera is installed and operated in low temperatures below 10 C 14 F normal images may not be obtained immediately after startup In such a case wait around 60 minutes or more How to install the heater unit Remove the camera s dome cover and mount it in the specified position with the supplied screw 2 Connect the heater unit cable to
6. vent water from being stored in the dehumidifying device If water remains inside the dehumidifying device cannot function properly Installation work shall be such that there is no intrusion of water into the architecture through the conduits having been joined 27 28 Make a connection Cautions e FOR UL LIST POWER SUPPLY Be sure to connect the grounding lead to the GND terminal ED MODEL S ONLY CONNECT THIS TO 24 V AC OR 12 V DC CLASS 2 Power cord Video output connection The video output connector is connected to the monitor or other system devices with a coaxial cable locally procured The maximum extensible length is shown in the BNC connector table Type of coaxial RG 59 U RG 6 U RG 11 U RG 15 U cable 8C 2V 6C 2V 7C 2V 10C 2V Recommended m 250 500 600 800 maximum cable length feet 825 1650 1980 2640 Power connection Precaution The following connections should be made by qualified service personnel or system installers in accordance with local electrical code NEC 725 51 for NTSC model Brown Live To 24 V AC 12 V DC Blue Neutral power supply Green Yellow GND To GND only for 24 V AC When using 12 V DC power supply the optional heater unit is unavailable BNC connector BNC connector To VIDEO IN e Wire colors amp functions Camera power cord Wire col
7. A 4 The model number and serial number of this product may be found on the surface of the unit You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006 95 EC and 2004 108 EC Wir erkl ren in alleiniger Verantwortung da das Produkt auf das sich diese Erklarung bezieht mit den folgenden Normen oder normativen Dokumenten bereinstimmt Gem den Bestimmungen der Richtlinie 2006 95 EC und 2004 108 EC CAUTION An ALL POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building Nous d clarons sous notre propre responsabilit que le produit auquel se r f re la pr sente d claration est conforme aux normes sp cifi es ou tout autre document normatif conform ment aux dispositions des directives 2006 95 CE et 2004 108 CE Turn the power off at the mains to disconnect the main power for all unit Nosotros declaramos bajo nuestra nica responsabilidad que el producto a que hace referencia esta declaraci n est conforme con las normas u
8. otros documentos normativos siguiendo las estipulaciones de las directivas 2006 95 CE y 2004 108 CE FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY WARNING This apparatus must be earthed IMPORTANT The wires in this mains lead are coloured in accor dance with the following code Green and yellow Earth Blue Neutral Brown Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be con nected to the terminal in the plug which is marked with the letter N or coloured black The wire which is coloured brown must be con nected to the terminal in the plug which is marked with the letter L or coloured red Noi dichiariamo sotto nostra esclusiva responsabilit che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive 2006 95 CE e 2004 108 CE Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende normen of andere normatieve documenten overeenkomstig de bepalingen van Richtlijnen 2006 95
9. the screws supplied with this product Important e Prepare the mounting screw according to the material of the area where the camera attach ment accessory is to be installed In this case wood screws and nails should not be used For mounting a camera on a concrete ceiling use an anchor bolt M4 or an AY plug bolt M4 for securing Recommended tightening torque M4 1 6 N m 1 18 Ibf ft e When using the provided camera attachment make sure that either of the arrow marks faces upward Required pull out capacity of a single screw bolt is 196 N 44 06 Ibf or more e f a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced When using an optional mounting bracket refer to the operating instructions of the bracket in use The mounting conditions of the camera mount bracket are described as follows Installation Applicable mount Recommended Number Minimum pull out place bracket screw of screw strength per 1 pc Ceiling wall Two gang junction box M4 or equivalent 4 pcs 196 N 44 06 Ibf Ceiling wall Mounting base M4 or equivalent 4 pcs 196 N 44 06 Ibf approx 350 g 0 77 lbs Ceiling WV Q169 i approx 700 g 1 55 Ibs Make sure that the installed mount bracket can support more than 5 times of the weight of the camera 15 Using a two gang junction box e When the camera is installed using the two gang junction box m
10. LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPE CIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PROD UCT PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REA SON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE 7 LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE 2 3 Contents Important safety instructions Limitation of liability Disclaimer of wartanly taii dtm trt ictum edita cepi et d eds ied ds Pr faogu iai erar nie ne oi nico A niin Ini ILI Features eer ek ee oe Hern eel ee ee e 7 PRECAUTIONS ordo b
11. Panasonic Operating Instructions Color CCTV Camera model no WV CW334S WV CW334SE WV CW364S WV CW364SE Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual WARNING This apparatus must be earthed Apparatus shall be connected to a mains sock et outlet with a protective earthing connection The mains plug or an appliance coupler shall remain readily operable All work related to the installation of this prod uct should be made by qualified service per sonnel or system installers For PERMANENTLY CONNECTED APPARATUS provided neither with an all pole MAINS SWITCH nor an all all pole circuit breaker the installation shall be carried out in accordance with all applicable installation rules The connections should comply with local electrical code For U S and Canada WV CW334S WV CW364S For Europe and other countries WV CW334SE WV CW364SE UL listed model No WV CW334S WV CW364S For Canada 4 This Class A digital apparatus complies with Canadian ICES 003 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrow head symbol withi
12. ation and white balance Simple day night mode selector D N for WV CW334S ON Selects the black white mode if the picture is dark it selects the color mode if the picture is bright enough OFF default Displays the color picture normally Note The simple day night function is estab lished by using the SENSE UP function for black white images The IR filter is secured Day night mode selector D N for WV CW364S ON Selects the black white mode if the picture is dark it selects the color mode if the picture is bright enough When set to ON the camera switches from color to black white images when the ambient brightness illuminance of the camera is approximately O 6 Ix or less OFF default Displays the color picture normally Note To obtain color images a sufficient level of illuminance approximately 30 Ix or more is required The switching illuminance level varies depending on subjects and light sources The switching illuminances described above are reference values The switching illuminance shall be decided based on the actual installation environment 13 14 Adaptive black stretch selector B S ON default Corrects the dark area of an object automatically to lighten it OFF Does not compensate Note e When set to ON noise may be increased in the dark area of the object In addition darkness and br
13. d waterproof process are done properly Camera Image sensor Effective pixels Scanning area Scanning system Scanning lines Scanning frequency Synchronization Resolution Minimum illumination Signal to noise ratio 1 3 type interline transfer CCD NTSC 768 H x 494 V PAL 752 H x 582 V 4 9 mm H x 3 7 mm V 3 16 inches x 5 32 inches 2 1 interlace NTSC 525 lines PAL 625 lines Horizontal 15 734 kHz NTSC 15 625 kHz PAL 59 94 Hz NTSC 50 00 Hz PAL Internal multiplexed vertical drive VD2 Horizontal 540 TV lines at center Vertical 350 TV lines NTSC at center 400 TV lines PAL at center WV CW364S 0 6 Ix C L 0 05 Ix B W F1 3 WIDE WV CW334S 0 6 Ix C L 0 4 Ix B W F1 3 WIDE 50 dB equivalent to AGC Off weight On Vertical Switch Function e Lens Type Focal length F number Focus range Angle of view Adjusting angle Simple day night mode selector for WV CW334S day night mode selector for WV CW364S ON OFF adaptive black stretch selector ON OFF backlight compensation selector ON OFF white balance selector ATW AWC 3 6x variable focal lens 2 8mm 10 0 mm F1 3 WIDE F3 1 TELE 1 2 m WV CW364S Horizontal 100 50 WIDE 27 39 TELE Vertical 73 51 WIDE 20 45 TELE WV CW334S Horizontal 100 18 WIDE 27 39 TELE Vertical 73 33 WIDE 20 45 TELE Panning range 180 to 140 Til
14. dication Zoom and focus adjustment At the same time as adjusting the pan and tilt Step 2 adjust the zoom and focus This illustration represents WV CW364S Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appropriate angle of view Tighten the zoom lock knob 2 Loosen the focus lock knob and move the knob between FAR and NEAR to obtain the optimum focus Tighten the focus lock knob Note e To change the angle of view by moving the zoom lock knob also move the focus lock knob to adjust the focus Mount the dome cover and inner dome Tighten the screws that have been loos ened in Step 2 in page 22 using the sup plied driver bit Recommended tightening torque 0 78 N m 0 58 Ibf ft Important e Attach the inner dome in accordance with the lens direction to not to change the lens direction Check if the tabs of the inner dome are firmly fit e Remove the protection sheet from the out side of the dome Cutout for Groove for mounting 26 Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when the camera with exposed cables is installed by means of the mounting base or it is installed under the eaves The camera body is waterproof but the cable ends are not waterproof Be sure to use the supplied butyl tape at the connection parts of the power cord and video output cable to apply waterproof
15. e contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further infor mation Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal For U S and Canada Panasonic System Networks Company of America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 2T3 Canada 905 624 5010 www panasonic ca O Panasonic System Networks Co Ltd 2011 Ns0211 0 For Europe and other countries Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg F R Germany STRO06876AZA Printed in China
16. ei eme tecto nsi remis 8 Precautions for installation recie eiecit o aded consucavadkesdouccesdedeatceeats 10 Major operating controls and their functions cccceeccceeesnseeeeeeneeeeeeseeeeeeeseaaeeeseeseeeesesneeeeessaes 12 PY P AN ATONNS c A 15 Camera installation ee EE EEE 19 Mak CONNECTION E EE EIE TED REO 000 MS 28 MPOUBIES MO OUING eee EPA 31 SPECINCANON Sse st cer eve PEE 32 Standard aceessories ndn cie de iilis r den ins seen e PE Pere ve Pep deselected 34 Optional 666S50N6S ME 35 This product is surveillance color CCTV camera equipped with a 1 3 type CCD solid state image sensor with 768 horizontal pixels NTSC 752 horizontal pixels PAL This camera can be mounted on a ceiling or a wall without any difficulty This product is provided with the adaptive black stretch function high resolution of 540 TV lines horizontal and minimum illuminance of 0 6 Ix C L 0 05 Ix B W for WV CW364S 0 4 Ix B W for WV OW3348 F1 3 WIDE thanks to the adoption of the newly developed digital signal processor Optional heater unit can be connected When using the optional heater unit the product can be used at temperatures within 30 C to 50 C 22 F to 122 F and humidity below 90 96 Precautions The following points as well as the con tents of Warning and Caution shall be observed Refer installation work to the dealer Installation wo
17. ightness may be emphasized in the vicinity of the bound ary between the dark and bright areas Backlight compensation selector BLC ON Compensates the background auto matically if it is brighter than the object OFF default Uses this mode when the front of the object is extremely bright Note e Under some conditions such as extremely strong backlight the desired compensa tion effect may not be achieved even if the mode is set to ON to detect the backlight level White balance selector ATW AWC ATW default Activates the automatic color temperature tracking mode The camera continuously measures the color temperature of the light source and automaticaly adjusts the white balance The adjustment of the color temperature ranges from approximate ly 2700 K to 6000 K AWC Activates the automatic white bal ance control mode This adjustment is suitable for a location where a light source is stable The adjustment of the color temperature ranges from approx imately 2000 K to 10000 K Monitor output connector RCA Connects the LCD monitor and such devices for checking images 5 Inner dome When installing the camera on a wall or a ceiling there are two methods as specified below Next page e Using a two gang junction box e Using the mounting base Refer to all work related to the installation of this product to qualified service personnel or system installer e The mounting base is supplied Use
18. lation near an air conditioner an air clean er a vending machine or the like causes noise Be sure to remove this product if it is not in use Keep the camera cable away from the lighting cable Failure to observe this may cause noise Radio interference When this product is used near TV radio anten na strong electric field or magnetic field near a motor or a transformer images may be dis torted and noise sound may be produced In such a case run the camera cable through specialized steel conduit tubes Locally procure the screws Screws are not supplied with this product Pre pare the screws according to the material structure strength and other factors of the mounting area and the total weight of objects to be mounted Screw tightening e The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area Do not use an impact driver Failure to observe this may cause overtightening and consequently damage to the screws e When a screw is tightened make the Screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure tightening is enough and there is no backlash Do not remove or loosen the screws Do not remove or even loosen the screws 7 pieces on the rear of the camera Otherwise water exposure may cause damage or malfunction of camera or camera dropping may result in injury
19. n an equilat eral triangle is intended to alert the user to the presence of uninsulated dangerous volt age within the product s enclo sure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruc tions in the literature accompa nying the appliance For U S A 4 NOTE This equipment has been tested and found to comply with the limits for a Class A digi tal device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction man ual may cause harmful interference to radio com munications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter ference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment For U S
20. n the direction of the arrow to the LOCK position camera to the camera attachment without any backlash to secure the Attachment mounting screw 19 20 lt To use the mounting base gt Attach the camera onto the camera attachment while aligning the OPEN mark of the camera with the projection of the camera attachment Important e When mounting the camera body cables shall be run between the camera attachment and mounting base as indicated by the arrow in the illustration Cable running as indicated by the arrow is an example Cable running shall be varied with installation environment 2 Engage the attachment mounting screw of the camera with the camera mounting hole of the camera attachment and rotate the camera in the direction of the arrow to the LOCK position to secure the camera to the camera attachment without any back lash 3 Connect the power cord and the video output cable at the side of the mounting base amp page 28 Apply waterproof treatment to the con nected section rs page 26 Make cable connections Accommodate the connected cables inside the cable guide of the mounting base Important e To prevent the cables from being caught when the cover is attached keep the cables inside the cable guide Connected cable Cable guide 21 5 Mount the supplied base cover on the mounting base Important o prevent the cables fr
21. om being caught when the base cover is attached keep the cables inside the cable guide 6 Use the bit for tamperproof screw acces Sory to tighten the fixing screws provided on both sides of the base cover Recommended tightening torque 0 78 N m 0 58 Ibf ft Remove the dome cover from the main body by loosening the three fixing screws Loosen the three fixing screws by using the provided bit for tamperproof screw Important Do not hold the inner dome when carrying the camera Otherwise the camera part may fall and it may damage the camera Note Perform the same procedure when replac ing with the optional dome cover WV CW4S 22 Base cover Base cover fixing screw Secure the camera to the bracket with the camera fixing screw red 1 position Important e The camera fixing screw shall be securely tightened Otherwise water exposure may cause damage or malfunction of camera or camera dropping may result in injury Recommended tightening torque 0 78 N m 0 58 Ibf ft Camera fixing screw red 23 Adjust the camera Pan tilt and azimuth adjustment Important Do not touch the iris motor Failure to observe this may cause trouble Do not hold the camera by the lens unit when adjusting panning tilting or azimuth Detach the inner dome from the camera by picking the front and rear sides Pick the portion marked in the illustration as well as the oppo
22. or 24 V AC 12V DC Brown 24 V AC L Positive Blue 24V AC N Negative Green yellow To GND Cautions Be sure to connect the GND grounding lead of the camera and grounding terminal of the power supply when using a 24 V AC power source Shrinking the cable entry seal is a onetime procedure Do not shrink the cable entry seal until it has been ascertained that unit is functioning Cord length and wire gauge 24 V AC The recommended cord length and copper wire size are shown in the table for reference The voltage supplied to the camera should be between 19 5 V AC and 28 V AC Recommended wire gauge for 24 V AC line Copper wire size 24 22 20 18 AWG 0 22 mm 0 33 mm 0 52 mm 0 83 mm Lengthof m 20 30 45 75 cable approx feet 66 100 150 250 12VDC The recommended resisance and copper wire size are shown in the table for reference The voltage supplied to the camera should be between 10 8 V DC and 16 V DC Resistance of copper wire 20 C 68 Copper wire size 24 22 20 18 AWG 0 22 mm 0 33 mm 0 52 mm 0 83 mm Resistance 0 m 0 078 0 050 0 03 0 018 T eS Resistance 0 ft 0 024 0 015 0 009 0 005 Use the formula below to calculate the power cord and power supply L R Va Il shall satisfy the inequalitty below 10 8 V DC lt Va 2 R xIx L lt 16 V DC L Cord length
23. ount the camera attachment accessory to the embedded box installed on the wall or ceiling as a first step Mounting position on wall or ceiling 1 13 16 inches y Two gang junction box SR Jd fa 83 5 mm 3 9 32 inches r A Camera attachment accessory Note e For wall mounting Installation shall be performed in such a manner that f TOP of the camera attachment faces upward For ceiling mounting The front side model number indication face of the camera shall be aligned in the direction of the arrow in FRONT on the camera attachment Using the mounting base When installing the camera with the mounting base attach the mounting base to the wall or ceiling in the first place next page Mount the camera attachment accessory by using the screws supplied with mounting brack et rs next page Recommended tightening torque 0 78 N m 0 58 Ibf ft Note e When installing the camera on the wall or ceiling where cable holes are already provided or when installing the camera with exposed wiring the mount bracket shall be used The female screws for piping conform to ANSI NPSM parallel pipe threads 3 4 inches The female screws for piping shall be removed with a hexagon wrench To connect conduit from the top refer to page 27 16 Install the mounting base on the wall ceiling 27 mm 1 1 16 inches Cable access hole For use of the hole p DA p 51 mm 2 inches 4 po
24. ower cord and connector is dam aged Use of the damaged cord or con nector may cause electric shock or fire Turn off the power immediately and request Warmed power cord or loos repair to your dealer ened connection by bending or stretching during use Heated portion of power line consisting of power cord gt during use 31 Specifications e Basic Power source Power consumption Ambient operating temperature Ambient operating humidity Water resistance Shock resistance Video output Dimensions Mass Finish NTSC 24 V AC 60 Hz 12 V DC PAL 24V AC 50 Hz 12 V DC 24 V AC 2 9 W without heater unit 13 1 W with heater unit 12 V DC 250 mA With Heater 30 C to 50 C 22 F to 122 F Without Heater 10 C to 50 C 14 F to 122 F Less than 90 no condensation Camera IEC60529 IP66 50J IEC60068 2 75 1 0 V p p 75 Q NTSC PAL composite BNC connector 9164 mm x 146 mm H 191 5 mm Base Cover 6 7 16 inches x 5 3 4 inches H 7 9 16 inches W Base Cover Main body 1 05 kg 2 31 Ibs including camera attachment 100 g 0 22 Ibs Mounting base 350 g 0 78 lbs Ceiling Mount Bracket 700 g 1 55 Ibs Main body Aluminum die cast light gray Dome cover Clear polycarbonate resin When using 12 V DC power supply the optional heater unit is unavailable Heater unit WV CW5H option Applicable only when the installation an
25. rk requires technique and experi ences Otherwise injury or damage to this product may result Be sure to consult the dealer Do not insert any foreign objects This could permanetly damage this product Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Stop operation immediately when some thing is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product con tinued use will result in fire injury or damage to the product Turn the power off immediately and contact qualified service personnel for service Select an installation area that can sup port the total weight Selecting an inappropriate installation surface may cause the product to fall down or topple over resulting in injury Installation work shall be started after sufficient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents Consult the dealer for the inspections This product shall be installed in a vibra tion free place Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury Install this product high enough to ensure that people don t hit
26. s such as a heater Handle this camera with care Do not drop this camera nor apply shock or vibration to this camera Failure to observe this may cause trouble Do not touch the dome cover with your bare hands A dirty dome cover causes deterioration of pic ture quality Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight the color filter of the CCD may have deteriorated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period the discoloration may remain Do not aim this product at strong light sources A light source such as a spot light causes a blooming light bleeding or a smear vertical lines Smear Blight subject Blooming Cleaning this product body Turn the power off when cleaning this product Do not use strong abrasive detergent when cleaning this product Otherwise it may cause discoloration Precautions for installation The following points as well as the contents of Warning and Caution shall be observed Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this docu mentation Installation work shall be performed in accordance with the technology standard of the electric installation This product is designed to be installed under eaves
27. site side Note Do not touch the lens At the same time as the pan and tilt adjust ments make the zoom and focus adjustments in Step 2 24 CD Rotate the panning table to adjust the pan ning position of the camera Range 320 The adjusting range is from 180 clock wise to 140 counterclockwise e Tighten the panning table lock screw after adjusting Panning lock screw Indication A CCD up side CW 180 CCW 140 Panning table 2 Rotate the tilting table to adjust the tilting position of the camera Range 75 This lens can also be rotated in the reverse direction but the image azimuth is reversed In such a case turn the panning table to the 180 side to correct the azi muth image When used at an angle that is close to hor izontal it must be noted that the shadow of the dome cover may be projected Fasten the tilting lock screws of both sides after adjusting 8 Tilting lock d T teu 3 UN screw x2 E Variable tilt angle x75 Note e When the zoom lock knob is adjusted to the WIDE side and the tilt angle is approx 75 1 3 part of the screen may be hid den Important e Tighten the panning table lock screw and tilting lock screw Recommended tighten ing torque 0 59 N m 0 44 Ibf ft 3 Rotate the azimuth adjuster to adjust the azimuth angle of the image Range 100 Azimuth adjuster In
28. the connector of the camera Screw for heater unit supplied with heater unit Heater output connector Two screws including a spare screw are provided as the standard accessories Important e After mounting the heater unit arrange the harness cable as shown in the drawing so as not to be tangled around the dome cover safety wire and equipment inside the camera Troubleshooting Before asking for repairs check the symptoms with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below Reference Symptom Cause solution pages e Are the power cord and coaxial cable connected appropriately Check whether the connection is appropriately established e s the adjusting monitor connected Check whether connection is estab 24 lished s the monitor brightness appropriately adjusted or is the contrast appropriately adjusted Check whether the monitor settings are appropriate No image displayed e s the dome cover free from contamina tion and or flaws Check the dome cover s the focus adjusted correctly p Check if the focus is adjusted correct 25 ly s the lens of the camera soiled with dirt or dust Check whether the lens of the camera is clean Blurred image Damaged power cord sheathing The p
29. their heads Failure to observe this may cause a drop result ing in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause injury or fire Turn the power off when do wiring of this product Failure to observe this may cause electric shock A short circuit or wrong wiring may cause fire Do not use this product in an atmosphere of flammable gases Failure to observe this may cause injury by explosion Avoid installing this product in locations where it is subject to damage by salt or corrosive gas Otherwise the mounting fixtures will deteriorate causing the product to fall down and leading to accidents Use the specified mount bracket Failure to observe this may cause a drop result ing in injury or accidents Do not rub the edges of metal parts with your hand Failure to observe this may cause injury Tighten screws and mounting fixtures to the specified torque Failure to observe this may cause a drop result ing in injury or accidents Precautions for use This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity Recommended operating temperature 35 C 95 F or lower Do not expose this product to direct heat source
30. ting Range 75 Azimuth Range 100 Dimensions and mass indicated are approximate Specifications are subject to change without notice 33 34 Standard accessories Installation Guide this book ees 1 pc Warranty card NTSC models only sssss 1 pc Mounting base Lune Fixing screw for mounting base incl 1 spare screw Camera attachment ie init dert pras 1 pc Bit for tamperproof screw esseeneeene 1 pc B tyl tape neret tet cic ted he eten isen 1 pc Optional accessories Dome cover WV CW4S Heater unit WV CW5H Ceiling mount bracket WV Q169 35 Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product Hei Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappro priate waste handling Pleas
31. treatment in the following procedure Failure to observe this may cause water leakage resulting in malfunction When using power cord When using video output cable lt How to wind the supplied butyl tape gt Stretch the tape by approx twice see the illustration below and wind it around the cable Insuffi cient tape stretch causes insufficient waterproofing LL LL LLI LL LL LLI Stretch the tape to about twice WP P M gg Mg ler ULL LILLA lt gt Dobled length Note To install this product outdoors be sure to waterproof the cables The camera body is water proof IEC IP66 or equivalent only when installation specified in this document and appropriate waterproofing are properly performed The bracket is not waterproof The cable shall be wound with butyl tape in a half overlapping manner Important f open wiring is conducted be sure to use conduits and run the cables inside the tubes to pro tect the cables from direct sunlight When the conduit is connected at the lateral or bottom position either of the arrow marks on the bracket shall be the top position When the conduit is connected from the top the arrow mark on the attachment shall be either of the right or left position To connect conduit from the side or bottom Arrow mark Connecting conduit For installation on the wall do not connect the dehumidifying device at the upper side to pre
32. ype plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 9 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 10 Only use attachments accessories specified by the manufacturer 11 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over 12 Unplug this apparatus during lightning storms or when unused for long periods of time Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE
Download Pdf Manuals
Related Search