Home

Panasonic WV-CP500 Operating Instructions

1. 18 Set the detection areas 19 Setting of scene change detection 20 Configure frame display 20 Configure alarm notification eeen 21 Camera system setting SYSTEM SETUP 22 10 Synchronization method selection SYNC 22 Setting of the power supply synchronization LL MOG 5s leleine 22 11 Alarm input output terminal setting ALARM IN OUT 23 Configure the alarm input terminal settings 23 Configure the settings relating to the alarm output terminali e ae rp e di kek ot 24 12 Privacy zone setting PRIVACY ZONE 24 13 Image stabilizer setting STABILIZER 25 14 Electronic zoom setting EL ZOOM 26 About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit Perform the settings for each item in accordance with the conditions of the camera shooting area The following is an example of setup procedure when LANGUAGE is set to ENGLISH Setup menu list Setup item Description kon CAMERA ID This item specifies the camera title The camera title that indicates the camera loca tion and other information about the camera is created with alphanumerics and sym 7 bols and is displayed on the screen CAMERA Performs the camera operation settings 8 SCENE1 SC
2. The area setting screen appears Step 3 Move the cursor to POSITION and press the setting button Step 4 Use the up down right and left buttons to determine the left upper position of the area to be set and press the setting button Step 5 Use the up down right and left buttons to determine the right lower position of the area and press the setting button Note e To delete an area move the cursor to DEL and press the setting button e The area to be brighter becomes circular e The bright level of an area cannot be specified e Only one area can be set When not using the SUPER D5 function Follow the procedure below Step 1 When the SUPER D5 function is set to OFF bright areas of an image are masked to facilitate the visibility of dark areas Move the cursor to MASK SET and press the setting button The mask setting screen appears ALC CONT screen Mask setting screen Area setting screen ALC CONT 1 BACK LIGHT COMP a e a m Ou UIL A SPUSR Sn Su l a SUPER D5 OFF MASK SET I pitt tt RET TOP END LEVEL MANUAL ABS I RET TOP END Step 2 Mask bright areas Use the up down right and left buttons to select an area to be masked and press the setting button When the selected area Is masked the masked area will start blinking between stripes and white screen When selecting another area after masking the masked area will be edisplayed in white Repeat the above
3. 5 Camera function 1 7 6 Camera function 1 7 7 Camera function 1 7 8 Camera function 1 7 9 Camera function 1 8 0 Camera function 1 8 1 Camera function 1 8 2 Camera function 1 8 3 Camera function 1 8 4 Camera function 1 8 5 Camera function 1 8 6 Camera function 1 9 0 Camera function 1 9 1 Camera function 1 9 2 Camera function 1 9 3 Camera function 2 0 1 Camera function 2 0 2 Camera function 2 0 7 Camera function 2 O 8 Camera function 2 O 9 Camera function 2 1 0 Camera function Setting contents Super Dynamic ON i VMD Super Dynamic ON Super Dynamic OFF Black and white control BW ON Black and white control BW OFF Black and white control BW AUTO 1 Camera title CAMERA ID ON Camera title CAMERA ID OFF Electronic zoom ON Electronic zoom OFF Black and white control BW AUTO 2 Iris of lens IRIS OPEN Iris of lens IRIS CLOSE Electronic shutter SHUTTER ON Electronic shutter SHUTTER OFF Electronic shutter soeed 1 step faster Electronic shutter soeed 1 step slower Gain adjustment AGC ON Gain adjustment AGC OFF Electronic sensitivity up SENS UP FIX ON Electronic sensitivity up SENS UP FIX OFF Electronic
4. When a continuously moving object is detected within a specified period an alarm signal is issued OFF default ON 5 s ON 10 s ON 20 s ON 30 s ON 40 s ON 50 s ON 1 min Detect objects that move into the specified direction Move the cursor to DIRECTION and select the direction from the following An alarm signal will be sent out when an object moves to the specified direction OFF default ON F ON ON PYON amp VON ON W ON 62 ON Ye Step 4 Move the cursor to AREA and select an area for which the motion detection is to be set All the alarm actions selected in step 3 will be applied to this area ALL default All areas will be set as the detection area SETUP When the setting button is pressed after selecting SETUP up to 2 areas can be set as the detection area Refer to pages 20 for how to configure the settings Step 5 Move the cursor to SENSITIVITY and press the setting button The SENSITIVITY screen appears Step 6 set the detection sensitivity and the minimum size of objects detected Perform the setup while viewing the detection result dis played on the screen Set the detection sensitivity Move the cursor to SENSITIVITY and select one of the following options for the detection sensitivity LOW default MID HIGH Set the minimum size of objects detected Move the cursor to MIN SIZE and select the minimum size of objects detected from the following The size options
5. Panasonic Operating Instructions Color CCTV Camera Model No WV C P500 WV CP504 This illustration represents WV CP500 Lens Option Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use No model number suffix is shown in this manual Preface About the user manuals The operating instructions of the camera consist of 2 sets these operating instructions PDF and Installation Guide This document explains how to configure the settings of the camera Refer to the installation guide for further information about how to install the camera Adobe Reader is required to read PDF When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and registered trademarks Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Contents 2 0 ee ee Ca ferret a a pen a ii 2 Back focus setting BACK FOCUS SETUP 27 About the user manuals 2 Special menu setting SPECIAL SETUP 29 Trademarks and registered trademarksS 2 Chroma level adjustment CHROMA GAIN 29 About the setup MENUS ii 4 Aperture level adjustment AP GAIN 29 SST I
6. A language for the setup menu is selected from the following The language selection can be made on the LANGUAGE SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen JAPANESE ENGLISH default FRANCAIS ESPANOL DEUTSCH ITALIANO PYCCKUV LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END To change the language to be used use the right or left button to select the target language move the cursor to SET and press the setting button Note e Vhen the language is changed the specified camera title is cleared 32 Shortcut operation Use of a system controller with the camera function button allows users to perform the shortcut settings with use of the numeric keypad and camera function button The available shortcut operations with this unit are shown as follows System controller operation 8 3 Camera function 8 4 Camera function 8 5 Camera function 9 0 Camera function 9 1 Camera function 9 2 Camera function 9 3 Camera function 9 4 Camera function 9 8 Camera function 9 9 Camera function 1 6 8 Camera function 1 6 9 Camera function 1 7 0 Camera function 1 7 1 Camera function 1 7 2 Camera function 1 7 3 Camera function 1 7 4 Camera function 1 7
7. Move the cursor to PUSH SW of ZOOM and press the setting button The zoom setting screen appears Step 3 Adjust the angular field of view by changing the electronic zoom factor up to 2x using the up or down button Note e Vhen the zoom factor is incremented resolution will be deteriorated Step 4 Move the cursor to PUSH SW of PAN TILT and press the setting button The pan tilt setting screen appears Step 5 Use the up down right and left buttons to determine the image position and press the setting button The position can be changed in the range of zoom factor set in the EL ZOOM screen Note e To reset to the default hold down the right and left buttons simultaneously for approx 2 seconds while the zoom setting screen or pan tilt setting screen is displayed Back focus setting BACK FOCUS SETUP Selects the back focus setting type and performs fine adjustment The following setting can be configured on the BACK FOCUS SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen The lens adjustment Installation Guide shall be performed before the back focus adjustment lt Back focus adjustment gt The back focus adjustment is performed by changing the distance between the lens and focal point Follow the procedure below Important e The auto back focus function is used for back focus adjustment at installation and for focus correction at switching between the
8. amp amp 12 SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATWI L DNR HIGH BW MODE AUTO1 1 VMD RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC INT ALARM IN OUT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF RET TOP END BACK FOCUS SETUP screen BACK FOCUS SETUP ABF PUSH SW MANUAL ADJ C Le B W AUTO SETUP SW LOCK OFF INDICATOR XXXX RET TOP END SPECIAL SETUP CHROMA GAIN ee AP GAIN PEDESTAL HUE PIX OFF COMMUNICATION COAX CAMERA RESET gt PUSH SW SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END Camera title setting CAMERA ID This item specifies the camera title The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols and is displayed on the screen The camera title is named with up to 16 characters Follow the procedure below to specify the camera title Top screen CAMERA ID screen Display positioning screen MODEL WV CP500 SERIES CAMERA ID ON L CAMERA SYSTEM BACK FOCUS l SPECIAL CAMERA ID 0123456789 FLOOR 1 ABCDEFGHIJKLM NOPQRSTUVWXYZ LANGUAGE sat m SPACE POSI RET TOP END RESET END SETUP ENABLE Editing area Step 1 select ON for CAMERA ID and then
9. direction the image becomes brighter and when the level indicator moves in the direction the image becomes darker Be sure to view a waveform monitor or a monitor when the adjustment is performed Chroma phase hue adjustment HUE Use the right or left button to adjust the pedestal level of the camera Be sure to view a vector chromaticity indicator or a monitor when the adjustment is performed Note e Holding down the right and left buttons for more than 2 seconds simultaneously restores the settings of CHROMA GAIN AP GAIN PEDESTAL and HUE to the default settings 29 Flaw compensation PIX OFF Flaws in the displayed camera image are corrected Up to 16 points can be corrected Follow the procedure below SPECIAL SETUP screen PIX OFF screen Pixel compensation positioning screen SPECIAL SETUP PIX OFF CHROMA GAIN AP GAIN 2 3 PEDESTAL 6 7 HUE COMMUNICATION COAX CAMERA RESET PUSH SW 000 000 SER NO XXXXXXXX RET TOP END RET TOP END Step 1 Move the cursor to PIX OFF and press the setting button The PIX OFF screen appears Step 2 Select a number 1 to 16 with which a pixel compensation point is registered and press the setting button The pixel compensation positioning screen appears Step 3 Use the up down right and left buttons to move the crosshair cursor to the center of the flaw to be corrected and press the set ting button The flaw is corr
10. RET TOP END Note e lf the top screen of the setup menu is called up with the operation buttons while a camera image is displayed the setup mode is always DISABLE to prevent opera tion errors To configure the settings in the setup menu change the setup mode to ENABLE e The cursor is a reversely highlighted part Step 1 Press the up or down button to move the cursor to END Step 2 Press the right button to move the cursor to SETUP and press the setting button to change the setup mode from DISABLE to ENABLE Step 3 Move the cursor to the item to be set and press the setting button Step 4 Perform the settings for each item e Selection of setting item Press the up or down button to move the cursor e Change of settings Press the right or left button e Display of advanced setup screen Press the setting button when is attached to the tar get setting item e Return to previous setup screen Move the cursor to RET and press the setting button e Return to the top screen Move the cursor to TOP and press the setting button Step 5 To return to the camera image screen move the cursor to END and press the setting button Screen transition diagram Top screen MODEL WV CP500 SERIES CAMERA ID OFF CAMERA SYSTEM BACK FOCUS SPECIAL LANGUAGE END SETUP ENABLE CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ
11. TOP END 1 Register a scene file SCENE1 SCENE2 It is possible to register 2 patterns of scene file For example when different settings are to be applied between day and night SCENE1 can be applied in the daytime and SCENE2 at night Change between the scene files can be made on the ALARM IN setting or shortcut operation e Pages 23 and 24 SCENE1 is set as the default setting Screen when SCENE1 is selected Screen when SCENE2 is selected CAMERA SETUP SCENE1 ALC ELC ALCI SHUTTER OFF AGC ON HIGH SENS UP OFF ATWI T HIGH CAMERA SETUP SCENE2 ALC ELC SHUTTER AGC ON HIGH SENS UP OFF ATWID HIGH AUTO1 L AUTO1 COPY SCENE1 RET TOP END RET TOP END Step 1 After confirming that SCENE1 is selected configure the settings of ALC ELC through i VMD e Pages 9 20 When using while changing the scene files go to step 2 Step 2 Move the cursor to SCENE1 and use the right or left button to select SCENE2 The COPY SCENE1 screen will be displayed Step 3 To configure the settings of SCENE2 using the settings of SCENE1 press the setting button after moving the cursor to COPY SCENE1 The settings of SCENE1 will be copied to SCENE2 ALC CONT 1 Scene file Step 4 BACK LIGHT COMP mD l l l SUPER D5 ON Edit the settings to be changed and saved as the settings of SCENE2 The number displayed at the right side of the title on each setting scre
12. be displayed after the number and the area setting will be saved Note e To delete the area select the area number and press the setting button after moving the cursor to DEL e To change the settings of the area select the area number and repeat from step 3 19 Setting of scene change detection This function detects a change in the subject state that occurs by covering the camera with a cloth a cap or others or by changing the camera direction largely Follow the procedure below CAMERA SETUP screen VMD SETUP screen CAMERA SETUP i VMD SETUP 1 SCENE1 MOTION DET ALC ELC ALC I OBJECT DET OFF SHUTTER OFF SCENE CHANGE OFF ON HIGH OFF INDICATOR OFF ATWI ALARM CONT HIGH AUTO1 RET TOP END RET TOP END Step 1 Move the cursor to i VMD and press the setting button The i VMD SETUP screen appears Step 2 Move the cursor to SCENE CHANGE and select from the following ON Provides an alarm signal when scene change is detected OFF default Disables scene change detection Configure frame display Follow the procedure below CAMERA SETUP screen VMD SETUP screen CAMERA SETUP i VMD SETUP 1 SCENE1 MOTION DET ALC ELC ALC I OBJECT DET OFF SHUTTER OFF SCENE CHANGE OFF AGC ON HIGH SENS UP OFF INDICATOR OFF ATWI ALARM CONT HIGH AUTOL RET TOP END RET TOP END Step 1 Move the cursor to i VMD and press the setting button The i VMD SETUP screen appe
13. brightness level 29 HUE Adjusts the chroma phase hue 29 PIX OFF Corrects image defects such as flaws 30 COMMUNICATION Performs the communication setting of the system with a receiver into which this unit 31 IS integrated CAMERA RESET Restores the settings in the setup menu to the default settings 31 SER NO Displays the serial number of this unit 31 LANGUAGE selects a language to be used in the setup menu 32 Basic operation The description below explains how to operate the setup menu basically The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor Refer to the installation guide for further information about the operation buttons The operations in the setup menu can also be performed through the system controller option Hold down the setting button for approx 2 seconas to call up the top screen of the setup menu MODEL WV CP500 SERIES CAMERA ID OFF CAMERA SYSTEM L BACK FOCUS SPECIAL LANGUAGE END SETUP DISABLE The setup mode changes to ENABLE and the setup menu becomes ready to be set MODEL WV CP500 SERIES CAMERA ID OFF CAMERA SYSTEM BACK FOCUS SPECIAL LANGUAGE END SETUP ENABLE The selected setup screen in the setup menu appears on the screen CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATWI J DNR HIGH BW MODE AUTO1 i1 VMD I
14. will be dis played in a green frame in the center of the screen In OFF position any object will be detected regardless of its size Perform the setup while viewing the detection result displayed on the screen OFF default SMALL MEDIUM LARGE Note e The detection sensitivity and minimum size selected in this step will be applied to all the alarm actions selected in step 3 e The detection areas set in step 4 will be displayed as a white frame on the SENSITIVITY screen e When a motion is detected a blue frame appears and changes to a red frame after a given time approx 1 sec on the SENSITIVITY screen In operation an alarm signal is provided when the frame changes to red 17 18 Perform the settings relating to the detection of appearance disappearance of stationary objects Perform the settings relating to the detection of appearance disappearance of stationary objects as follows Up to 4 appearanc es disappearances of stationary objects can be simultaneously detected However use of the scene change detection function decreases the maximum simultaneous detectable appearances disappearances of stationary objects to 3 Follow the procedure below CAMERA SETUP screen i VMD SETUP screen OBJECT screen SENSITIVITY screen CAMERA SETUP i VMD SETUP 1 OBJECT DET 1 SENSITIVITY 1 SCENE1 MOTION DET REMOVAL AND LEFT BEHIND MIN SIZE OFF ALC ELC ALC 1 OBJECT DET ON i SHUTTER OFF SCENE CHANGE OFF DURATION T
15. 00 and 1 10 000 When the SUPER D5 function is set to ON or ON i VMD OFF 1 60 default 1 100 Note e When ALC ELC is set to ELC or ALC e page 9 appears and the electronic shutter function cannot be activated e f the controller WV CU254 or WV CU204 is used SW LED and the status of SHUTTER are not correctly displayed 4 Gain control setting AGC select a gain control setting from the following ON HIGH default ON MID ON LOW Automatically increases the gain to make the screen brighter when the illuminance of the subject becomes darker HIGH MID and LOW indicate the gain level OFF Does not increase the gain Note e Vhen SENS UP is set to the AUTO mode AGC cannot be set to OFF 5 Electronic sensitivity enhancement setting SENS UP Use of the electronic sensitivity enhancement function increases the quantity of light stored on the CCD and accordingly the image becomes brighter The magnification is unchanged for selection of FIX and the magnification is changeable in accor dance with the illuminance of a photographic subject for selection of AUTO The magnification of the electronic sensitivity is selectable from the following The setting of the SUPER D5 function restricts the available setting range When the SUPER D5 function is set to OFF OFF default X2 AUTO X4 AUTO X6 AUTO X10 AUTO X16 AUTO X32 AUTO OFF X2 FIX X4 FIX X6 FIX X10 FIX X16 FIX X32 FIX When the SUPER
16. D5 function is set to ON or ON i VMD OFF default X2 AUTO X4 AUTO X6 AUTO X10 AUTO X16 AUTO X32 AUTO Note e When ALC ELC is set to ELC or ALC 1e page 9 or SHUTTER is set to 1 100 i page 11 only the AUTO mode is enabled When SHUTTER is set to OFF or other than 1 100 the electronic sensitivity enhancement setting cannot be performed appears and OFF is selected It is impossible to select AUTO for SENS UP and 1 100 for SHUTTER using the following system controller Use the operation buttons for the setting WV CU300 WV CU354 WV CU204 WV CU254 e When the magnification of SENS UP is increased the screen becomes coarser more whitish or more flawed However this phenomenon is normal If the controller WV CU254 or WV CU204 is used SW LED and the status of SENS UP are not correctly displayed 6 White balance setting WHITE BAL The white balance adjustment is selectable from the following ATW1 default Activates the automatic color temperature tracking mode The camera continuously measures the color tem perature of the light source and automatically adjusts the white balance The adjustment of the color temperature ranges from approx 2 700 K to 6 OOO K Note lf the situation meets one of the following or other color may not be accurately reproduced e The subject is mostly highly colored e The photographic atmosphere is under the bright blue sky or at nightfall e The illu
17. ENE2 Selects a scene file It is possible to register and save the settings as a scene file in case that it is necessary to change the settings such when shooting at night or on hol 8 idays ALC ELC Selects the method of controlling the quantity of light in accordance with the lens to 9 be used SHUTTER Specifies the electronic shutter speed 11 AGC Specifies gain adjustment 12 SENS UP Specifies electronic sensitivity enhancement 12 WHITE BAL Specifies white balance adjustment 12 DNR Selects the level of the digital noise reduction function 14 BW MODE Performs each setting regarding the black and white mode such as switching 14 between color and black and white images I VMD Performs settings regarding intelligent VMD Video Motion Detector such as motion 15 detection and object abandonment removal detection SYSTEM Performs the settings regarding the camera system such as synchronization alarm 22 input output and privacy zone SYNC specifies the synchronization type 22 ALARM IN OUT Performs the settings of the ALARM IN connector and the ALARM OUT connector 23 PRIVACY ZONE Hides undesired portions in the camera shooting area 24 STABILIZER Decides whether or not to enable the image stabilizer 25 EL ZOOM Toggles the electronic zoom on and off 26 BACK FOCUS selects the back focus setting type and performs fine adjustment 27 SPECIAL CHROMA GAIN Adjusts the chroma level 29 AP GAIN Adjusts the aperture level 29 PEDESTAL Adjusts the pedestal
18. ER D5 function all the time See below In addition to the SUPER D5 function the motion detection function also works OFF Deactivates the SUPER D5 function re Page 11 Note e When ON or ON i VMD is selected for SUPER D5 the following settings will be restricted SHUTTER Only OFF and 1 100 are available Page 11 SENS UP Only OFF and AUTO become available re Page 12 e When ON or ON i VMD is selected for SUPER D5 a shadow black line may appear at the boundary between a bright er area and a darker area This is not a malfunction e When ON or ON i VMD is selected for SUPER D5 the SUPER D5 function will become more effective by slightly incre menting LEVEL However flickering or noise may be observed frequently when LEVEL is too much incremented e When flickering or noise is observed frequently due to the illumination of light select OFF 1 When flickering or color deterioration is observed 2 When noise is produced in a bright area on the screen e When ON i VMD is selected for SUPER D5 performance of the motion detection will vary depending on the i VMD set tings s Steps 4 6 on page 17 When using the SUPER D5 function Follow the procedure below Step 1 Move the cursor to LEVEL and use the right or left button to adjust the level Step 2 The dark area of the object is automatically corrected to lighten it Move the cursor to MANUAL ABS and press the setting button
19. IME AGC ON HIGH AREA SENS UP INDICATOR OFF SENSITIVITY WHITE BAL pi ALARM CONT AUTOLl RET TOP END RET TOP END RET TOP END RET TOP END Step 1 Move the cursor to i VMD and press the setting button The i VMD SETUP screen appears Step 2 Move the cursor to OBJECT DET and press the setting button The OBJECT DET screen appears Step 3 Move the cursor to DURATION TIME and select the wait time of appearance disappearance of stationary objects from the fol lowing 10 s default 20 s 30 s 40 s Step 4 Move the cursor to AREA and select the area for which the detection of appearance disappearance of stationary objects is to be set ALL default All areas will be set as the detection area SETUP When the setting button is pressed after selecting SETUP up to 2 areas can be set as the detection area Refer to pages 18 for how to configure the settings Step 5 Move the cursor to SENSITIVITY and press the setting button The SENSITIVITY screen appears Step 6 Move the cursor to MIN SIZE and select the minimum size of objects detected from the following The size options will be dis played in a green frame in the center of the screen In OFF position any object will be detected regardless of its size Perform the setup while viewing the detection result displayed on the screen OFF default SMALL MEDIUM LARGE Note e The detection areas set in step 4 will be displayed as a
20. MO MU list 4 Pedestal level adjustment PEDESTAL 29 Basic operation 5 Chroma phase hue adjustment HUE 29 Screen transition diagram 6 Flaw compensation PIX OFF 30 Camera title setting CAMERA ID 7 Communication setting COMMUNICATION 31 Camera operation setting CAMERA SETUP 8 Default resetting CAMERA RESET 31 1 Register a scene file SCENE1 SCENE2 8 Serial number viewing SER NO 31 2 Light quantity control method selection ALC ELC 9 Language selection LANGUAGE SETUP 32 SUPER D5 super dynamic function 9 Shortcut operation 33 SUPER D5 Settihg ieocmncnasi fok kan ka y a 9 3 Electronic shutter setting SHUTTER 11 4 Gain control setting AGC i 12 5 Electronic sensitivity enhancement setting SENS UP fe l bon klate si aba aa pa ae fa a 12 6 White balance setting WHITE BAL 12 Manual fine adjustment of white balance 14 7 Digital noise reduction function setting DNRL 14 8 Black and white mode setting BW MODE 14 9 i VMD setting i VMD 16 Perform the settings relating to the detection of appearance disappearance of stationary objects
21. Page 16 BW Automatically activates the black and white mode when the terminal input is active SCENE2 Operates the camera with the settings of SCENE2 when the terminal input is active When no terminal input is received the camera will work with the settings of SCENE 1 23 Configure the settings relating to the alarm output terminal select the alarm output operation Follow the procedure below SYSTEM SETUP screen ALARM IN OUT screen SYSTEM SETUP ALARM IN OUT SYNC INT ALARM IN OUT ALARM IN OFF ALARM OUT OFF PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF RET TOP END RET TOP END Step 1 Move the cursor to ALARM IN OUT and press the setting button The ALARM IN OUT screen appears Step 2 Move the cursor to ALARM OUT and select the alarm output terminal operation from the following OFF default Does not perform terminal output ALARM The alarm output will be performed upon a i VMD detection The alarm output will also be performed when receiving an alarm input while operation with setting ALARM for ALARM IN BW Activates the output terminal while an image is displayed in the black and white mode 12 Privacy zone setting PRIVACY ZONE When undesired portions in the camera shooting area on the screen exist those portions privacy zone are hidden Up to 8 portions can be specified for the privacy zone ON 1 Grays the zone ON 2 Mosaics the zone OFF default Displays
22. VMD The intelligent motion detection function allows the camera to detect motion and appearance disappearance of an object or scene change with the camera Detection of motion and appearance disappearance of an object or scene change with the camera can be announced by issuing an alarm signal or displaying a frame on the screen Important e The following circumstances may result in detection failure or false detection Adjusting the detection area and sensitivity may cause detection failure Not enough difference in brightness between the background and the moving photographic subject or significant changes in brightness Dirt or water drops on the lens Insufficient brightness for example when shooting at night The subject is moving straight at the camera The subject is moving too fast or too slow The subject is too small or too large There are too many moving objects Light reflected through a window or from a road surface The camera is shaking Entry of outside light such as sunlight or the headlights of a car Flickering fluorescent light e Scene change detection may fail in the following cases The lens is partially covered or covered with a transparent item The photographic subjects before and after changing the camera direction are similar e False detection may occur for approx 1 minute after turning on the power after completing settings in the SETUP menu or after changing the camera view angle Perform the settings r
23. amera to a 2 input oscilloscope and move the cursor to COARSE Step 3 Adjust the oscilloscope to the vertical rate and extend the vertical synchronizing part of the oscilloscope Move the cursor horizontally with use of the right or left button to roughly adjust the vertical phase The phase can be adjusted in 16 steps by 22 5 degrees 1 1 16 O 2 1 16 22 5 94 16 01 16 337 5 Step 4 Move the cursor to FINE and fine adjust vertical phases 11 Alarm input output terminal setting ALARM IN OUT Configure the settings relating to the alarm input output terminal as follows Configure the alarm input terminal settings Select the operation of the alarm input terminal Follow the procedure below SYSTEM SETUP screen ALARM IN OUT screen SYSTEM SETUP ALARM IN OUT SYNC INT ALARM IN OUT I ALARM IN OFF ALARM OUT OFF PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF RET TOP END RET TOP END Step 1 Move the cursor to ALARM IN OUT and press the setting button The ALARM IN OUT screen appears Step 2 Move the cursor to ALARM IN and select the alarm input terminal operation from the following OFF default No terminal input is accepted ALARM Activates the alarm action when the terminal input is active for more than 100 ms VMD PERMIT Activates the intelligent VMD function when the terminal input is active It is necessary to set actions to be taken in the i VMD section in advance e
24. ars Step 2 Move the cursor to INDICATOR and determine whether or not to display a frame around the screen from the following OFF default Does not display a frame ON ALL Displays a frame ON OBJ Display the appearance disappearance frame only Configure alarm notification Follow the procedure below CAMERA SETUP screen VMD SETUP screen CAMERA SETUP i VMD SETUP 1 SCENE1 MOTION DET ALC ELC ALC OBJECT DET OFF SHUTTER OFF SCENE CHANGE OFF AGC ON HIGH SENS UP INDICATOR OFF ALARM CONT AUTOL RET TOP END RET TOP END Step 1 Move the cursor to i VMD and press the setting button The i VMD SETUP screen appears Step 2 Move the cursor to ALARM and configure alarm notification CONT default Continues to send alarm signals upon detection 1TIME Sends an alarm signal only once 100 ms at detection start 21 22 Camera system setting SYSTEM SETUP Performs the settings relating to the camera system such as synchronization alarm input output terminal and privacy zone The following settings can be configured on the SYSTEM SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen SYSTEM SETUP screen SYSTEM SETUP 10 SYNC INT 1 ALARM IN OUT I 12 PRIVACY ZONE OFF 13 4 STABILIZER OFF 14 EL ZOOM OFF RET TOP END 10 Synchronization method selection SYNC This unit supports the following 3 types of synchron
25. ching between color and black and white images PRESET Performs the preset movement to each specified back focus position when switching between color and black and white images The preset position is the back focus position specified last time which was automatically memorized for each of color images and black and white images FIX Fixes the position after adjusting the back focus either automatically ABF or manually Step 4 Moving the cursor to SETUP SW LOCK and selecting ON allow users to disable the back focus adjustment with the operation buttons default OFF Important e The following are recommendation for back focus setting in accordance with subjects For such case subject conditions Select this recommendation CIL gt B W switching Normal subject ABF AUTO Frequently moving subj Fine adjustment with MANUAL ADJ PRESET or FIX Subj with remarkable illuminance _ after ABF or MANUAL ADJ change Subj with low illuminance Too bright or reflective subj Subj through a window e Place where the lens easily becomes dirty Subj with less contrast such as white wall Subj with remarkable depth Subj with heavy flicker Subj with horizontally parallel lines such as a shutter e We shall not responsible for any inconvenience loss or damage caused by the settings or results of the back focus func tion Special menu setting SPECIAL SETUP The special menu setup is per
26. color and black and white modes after installation This function is not a function that is supposed to be operated contin uously such as the auto focus function e Vhen focus missing occurs due to secular change in the lens and installation environment or peripheral temperature change the back focus adjustment is required again Note e The back focus adjustment can be also performed through the operation buttons Installation Guide BACK FOCUS SETUP screen BACK FOCUS SETUP ABF PUSH SW MANUAL ADJ I C Le B W AUTO SETUP SW LOCK OFF INDICATOR XXXX FOCUSING RET TOP END Step 1 Move the cursor to PUSH SW of ABF and press the setting button The auto back focus function provides back focus adjustment to automatically focus on a subject located in the center of the screen Step 2 To fine adjust the back focus move the cursor to MANUAL ADu press the setting button and use the right or left button to adjust the back focus manually Note e Pressing the right and left buttons simultaneously for more than 2 seconds resets the back focus position to the CS mount default position e The value of INDICATOR is a guide to adjust the back focus The larger the value is the sharper the image becomes 21 28 Step 3 Move the cursor to C L B W and select the back focus adjustment type from the following AUTO default Adjusts the back focus function automatically and corrects out of focus when swit
27. ected and the pixel compensation point is registered The PIX OFF screen appears again the right side of the number when registration is completed The coordinate is expressed in figures ki Is attached at Note e To clear the registered pixel compensation point move the cursor to the number with which the target pixel compensation point is registered on the PIX OFF screen and press the setting button The pixel compensation positioning screen appears and then hold down the right and left buttons for more than 2 seconds simultaneously The PIX OFF screen appears the pixel compensation point is cleared and at the right side of the number disappears 30 Communication setting COMMUNICATION The required communication configuration is performed to use this unit integrated into the system with a receiver COAX RCV Select COAX RCV when using our receiver e g WV RC100 or WV RC 150 COAX default Does not use any receiver Default resetting CAMERA RESET The settings in the setup menu are restored to the default settings The default settings are restored by moving the cursor to PUSH SW of CAMERA RESET and holding down the right left and setting buttons for more than 2 seconds simultaneously Note e The data of the back focus setting and registered pixel compensation points is not cleared Serial number viewing SER NO The serial number of this unit appears 31 Language selection LANGUAGE SETUP
28. elating to the motion detection Perform the settings relating to the motion detection as follows It is possible to detect only objects that moves to the direction specified in advance or objects that keeps on moving for a certain duration Up to 4 motions can be simultaneously detected Follow the procedure below CAMERA SETUP screen VMD SETUP screen MOTION DET screen SENSITIVITY screen CAMERA SETUP i VMD SETUP 1 MOTION DET 1 SENSITIVITY 1 OFF SCENE1 MOTION DET I MOTION SENSITIVITY LOW ALC ELC ALC I OBJECT DET OFF LOITERING OFF MIN SIZE OFF SHUTTER OFF SCENE CHANGE OFF DIRECTION OFF AGC ON HIGH SENS UP OFF INDICATOR OFF AREA ALL WHITE BAL ATWI ALARM CONT SENSITIVITY DNR HIGH BW MODE AUTOT i VMD I RET TOP END RET TOP END RET TOP END RET TOP END Step 1 Move the cursor to i VMD and press the setting button The i VMD SETUP screen appears Step 2 Move the cursor to MOTION DET and press the setting button The MOTION DET screen appears Step 3 The setting of the motion detection mode is performed This unit has 3 types of motion deteciton modes Detect motion of objects Move the cursor to MOTION and select from the following ON Provides an alarm signal when motion is detected OFF default Does not detect motion Detect objects that move continuously within a specified period Move the cursor to LOITERING and select the duration from the following
29. en inidicates a scene file number MANUAL ABS RET TOP END Step 5 Move the cursor to SCENE1 and press the right or left button to select SCENE1 to resume normal operation Important e When SCENE2 is set for ALARM IN the SCENE X EXT indication will be displayed and it is impossible to change the scene file X indicates 1 or 2 2 Light quantity control method selection ALC ELC The method of controlling the quantity of light is selected from the following in accordance with the lens to be used ALC default The iris of the lens is automatically adjusted in accordance with the brightness of a subject Select ALC when using the SUPER D5 function or when using an ALC lens Refer to the following when configuring the SUPER D5 settings ALC Controls the quantity of light with a combination of the electronic shutter and auto iris This selection is suitable at shoot ing a bright subject such as an outdoor subject with auto iris lens Be aware that flicker may occur when a subject is under fluorescent lighting ELC Controls the quantity of light with the electronic shutter This selection is suitable for use of a lens with fixed iris or manual iris Subject in the dark Subject in the bright SUPER D5 super dynamic fu nction area is hard to notice area is hard to notice If there is high contrast between the bright and dark areas in a shooting zone the a dark area becomes less visible because the camera adj
30. formed including the setting of the camera image quality and the communication configuration when a receiver is used The following settings are to be configured on the SPECIAL SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen SPECIAL SETUP CHROMA GAIN AP GAIN PEDESTAL HUE PIX OFF COMMUNICATION COAX CAMERA RESET PUSH SW SER NO XXXXXXXX RET TOP END Chroma level adjustment CHROMA GAIN Use the right or left button to adjust the color density of the camera image When the level indicator moves in the direction the color becomes deeper and when the level indicator moves in the direction the color becomes lighter Be sure to view a vector chromaticity indicator or a monitor when the adjustment is performed Aperture level adjustment AP GAIN Use the right or left button to adjust the image quality When the level indicator moves in the direction the image becomes sharper and when the level indicator moves in the direction the image becomes softer Be sure to view a monitor when the adjustment is performed Note e Moire interference fringes may be observed when shooting a subject with fine pattern such as a carpet or a curtain In such a case move the indicator in the direction to reduce moire Pedestal level adjustment PEDESTAL Use the right or left button to adjust the pedestal level of the camera When the level indicator moves in the
31. ization methods and one of the following is selected 1 Multiplexed vertical drive signal VD2 2 Synchronization is performed on the basis of the power supply frequency 3 Internal synchronization INT default Input of a multiplexed vertical drive signal VD2 automatically switches to the VD2 synchronization even if the camera is set to other than the VD2 synchronization method When other than the VD2 synchronization is selected either the power supply synchronization or internal synchronization can be selected Note e The power supply synchronization LL setting is changeable only in the 60 Hz areas The power supply synchronization LL cannot be setup in the 50 Hz areas Setting of the power supply synchronization LL mode The adjusting video signal of the camera and the criterial external synchronizing input signal power are connected to a 2 input oscilloscope and the phase is adjusted Note e Movement of the camera or presence of a spike noise in the power line may cause vertical phase change In such a case adjust the phase again Follow the procedure below SYSTEM SETUP screen SYNC screen SYSTEM SETUP SYNC SYNC LL ALARM IN OUT PRIVACY ZONE 1 1 16 STABILIZER EL ZOOM RET TOP END RET TOP END Step 1 set SYNC to LL and press the setting button The SYNC screen appears Step 2 Connect the video output signal and external synchronizing input signal of the c
32. k and white images is per formed from the following LOW Switches from color to black and white images when the ambient brightness illuminance of the camera is approx 0 1 x or less HIGH default Switches from color to black and white images when the ambient brightness illuminance of the camera is approx 0 2 Ix or less Note e To obtain color images a sufficient level of illuminance approx 30 Ix or more is required e The switching illuminance level varies with subjects light sources and lenses e The switching illuminance level varies in accordance with AGC setting Page 12 e The switching illuminances described above are reference values The switching illuminance shall be decided based on the actual installation environment Step 4 Move the cursor to DURATION TIME and select a time for switching between color and black and white images from the fol lowing default 10 seconds 2 sec 10 sec 30 sec 60 sec S L Step 5 Move the cursor to BURST BW and decide whether or not to provide a burst signal output in the black and white mode ON default Provides a burst signal output OFF Does not provide any burst signal output Note e Images may not be displayed appropriately without burst signals when camera images are displayed in the black and white mode depending on a monitor or VCR model to be used In such a case set the burst signal output to ON 15 16 9 i VMD setting i
33. mination of the light illuminating the subject is insufficient ATW2 Activates the sodium lamp automatic color temperature tracking mode The camera automatically achieves an optimal white balance under the sodium lamp The adjustment of the color temperature ranges from approx 2 000 K to 6 000 K AWC Activates the automatic white balance control mode This adjustment is suitable for a location where a light source is sta ble The adjustment of the color temperature ranges from approx 2 000 K to 10 000 K When AWC is selected the white balance needs to be adjusted When AWC is selected follow the steps below to adjust the white balance CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER OFF AGC ON HIGH SENS UP OFF AWC PUSH SW HIGH AUTO1 RET TOP END Step 1 set WHITE BAL to AWC and press the left button to change to AWC gt PUSH SW Step 2 Press the setting button and adjust the white balance PUSH SW is reversely highlighted during adjustment When the reversely highlighted display is restored the white balance adjustment is completed Step 3 Press the right button to select AWC Refer to the following for fine adjustment of the white balance Note e The adjustment of the color temperature ranges from approx 2 000 K to 10 000 K If the correct range is out of this adjust ment range or lighting directed to a subject is too dark the white balance may not completely adj
34. mpany Panasonic Puerto Rico Inc AVE 65de Inf Km 9 5 Carolina PR 00985 787 750 4300 N0409 1069 31R005979BZB Printed in China
35. nt e When BW is set for ALARM IN the EXT indication will be displayed for BM MODE and it is impossible to change the setting Page 23 CAMERA SETUP screen BW MODE screen CAMERA SETUP BW MODE 1 SCENE1 ALC ELC AUTO1 SHUTTER LEVEL HIGH AGC DURATION TIME S L SENS UP BURST BW ON AUTO1 RET TOP END RET TOP END Step 1 Move the cursor to BW MODE and select the black and white control from the following AUTO1 default Automatically toggles between color and black and white images in accordance with the screen brightness illuminance The black and white mode is selected for dark images and the color mode is selected for bright images AUTO2 Uses a near infrared light source at nighttime ON Displays black and white images OFF Displays color images Note e The auto back focus function also allows users to correct out of focus when changing between color and black and white images Page 27 e f a subject is always moving or the screen is occupied with a uniform color brightness determination may be not performed successfully because the brightness is merely determined by information from the CCD image sensor When AUTO2 is selected the wave length of the light source shall be 800 nm or longer Step 2 Press the setting button The BW MODE screen appears Step 3 Move the cursor to LEVEL and select a brightness level at which switching between color and blac
36. press the setting button The CAMERA ID appears Important e When CAMERA ID is set to OFF the camera title does not appear even after setting the camera title Step 2 Move the cursor to the target item with use of the up down right and left buttons and press the setting button to enter the character The entered characters are displayed in the editing area lt Character entry gt e To revise a character move the arrow T in the entry range to a wrong character with use of the right or left button and enter a correct character e To enter a blank move the cursor to SPACE and press the setting button e To delete all the entered characters move the cursor to RESET and press the setting button Step 3 Move the cursor to POSI and press the setting button after title entry The display positioning screen appears Step 4 Use the up down right and left buttons to decide the title position and press the setting button The camera title and title position are specified Camera operation setting CAMERA SETUP The following describes the camera operation settings The following settings can be configured on the CAMERA SETUP screen displayed from the top screen Refer to page 5 for how to call up the screen The settings configured on the CAMERA SETUP screen will be saved as a scene file CAMERA SETUP screen CAMERA SETUP ALC I OFF ON HIGH OFF ATWI l HIGH AUTO1 RET
37. procedure to mask other areas as necessary Note e To cancel the masking select the masked area to be canceled and then press the setting button e To cancel all the masking press the right and left buttons simultaneously for 2 seconds or more Step 3 Hold down the setting button for approx more than 2 seconds after completion of masking The ALC CONT screen ELC CONT or ALC CONT screen appears again Step 4 Move the cursor to LEVEL and use the right or left button to adjust the level Step 5 The dark area of the object is automatically corrected to lighten it Move the cursor to MANUAL ABS and press the setting button The area setting screen appears Step 6 Move the cursor to POSITION and press the setting button to select an area The setup procedure is the same as the setting operation in the process of SUPER D5 function re Steps 4 5 on page 10 3 Electronic shutter setting SHUTTER The variation in electronic shutter soeed allows users to perform the following e Increased shutter soeed prevents blurring fast moving subjects e f flicker is observed under fluorescent lighting of 60 Hz selection of 1 120 for the speed can reduce flicker The electronic shutter speed is selectable from the following The setting of the SUPER D5 function restricts the available setting range 11 When the SUPER D5 function is set to OFF OFF 1 60 default 1 100 1 250 1 500 1 1 000 1 2 000 1 4 0
38. sensitivity 1 step up FIX Electronic sensitivity 1 step down FIX Electronic sensitivity up SENS UP AUTO ON Electronic sensitivity up SENS UP AUTO OFF Electronic sensitivity 1 step up AUTO Electronic sensitivity 1 step down AUTO Power supply synchronizing phase adjustment FINE 1 step up Power supply synchronizing phase adjustment FINE 1 step down BW AUTO switching time 2 sec BW AUTO switching time 10 sec BW AUTO switching time 30 sec BW AUTO switching time 60 sec Image stabilizer STABILIZER ON Image stabilizer STABILIZER OFF Motion detection MOTION ON Motion detection MOTION OFF Object abandonment removal detection ON Object abandonment removal detection OFF 33 34 System controller operation 2 1 2 Camera function 2 1 3 Camera function 2 1 4 Camera function 2 1 5 Camera function 2 1 6 Camera function Setting contents scene change ON scene change OFF scene file 1 scene file 2 Gain AGC 1 step up Gain AGC 1 step down Panasonic System Solutions Company Unit Company of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way 2H 2 Secaucus New Jersey 07094 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 2T3 Canada 905 624 5010 http www panasonic ca Panasonic Corporation 2009 Panasonic Sales Co
39. stalled on a power pole or other poles ON Enables the image stabilizer OFF default Disables the image stabilizer Important e When ON is selected for the image stabilizer the view angle becomes narrower and the resolution becomes lower When ON is selected for the image stabilizer check the view angle and resolution at camera installation e The image stabilizer function may not work for the following subjects or conditions e Dark subject e Less contrasty subject e g white wall e Short cycled image shaking such as mechanical vibration e Large amplitude image shaking 25 14 Electronic zoom setting EL ZOOM select On or Off to determine whether or not to use the electronic zoom When ON is selected the zoom factor and the panning tilting settings can be configured ON Uses the electronic zoom OFF default Does not use the electronic zoom Follow the procedure below SYSTEM SETUP screen EL zoom setting screen Zoom setting screen Pan tilt setting screen SYSTEM SETUP EL ZOOM EL ZOOM EL ZOOM SYN IN ALARM IN OUT PUSH SW PUSH SW PUSH SW ZOOM ZOOM ZOOM PAN TILT PUSH SW PAN TILT PUSH SW PAN TILT PUSH SW PRIVACY ZONE OFF STABILIZER OFF EL ZOOM ON U ZOOM D U TILT D L PAN R RET TOP END RET TOP END RET TOP END RET TOP END Step 1 Move the cursor to EL ZOOM select ON and press the setting button The EL ZOOM screen will be displayed Step 2
40. the zone normally Follow the procedure below Note e The privacy zone function is disabled at initializing the unit i e right after turning on the power SYSTEM SETUP screen Zone setting screen SYSTEM SETUP ZONE NUMBER 1 8 SYNC INT ALARM IN OUT I POSITION PUSH SW PRIVACY ZONE ON L UPPER LEFT STABILIZER OFF EL ZOOM OFF DEL RET TOP END RET TOP END Step 1 Move the cursor to PRIVACY ZONE select ON 1 or ON 2 and press the setting button The zone setting screen appears Step 2 Move the cursor to the number at the right of the title and select the zone number using the right or left button Step 3 Move the cursor to POSITION and press the setting button Step 4 Use the up down right and left buttons to determine the left upper position of the zone to be set and press the setting button Step 5 Use the up down right and left buttons to determine the lower right position of the zone to be set and press the setting button The asterisk mark will be displayed after the number and the zone setting will be saved Note e To delete a zone select the zone number and press the setting button after moving the cursor to DEL e To change the settings of a zone select the zone number and repeat from step 3 13 Image stabilizer setting STABILIZER Whether or not to enable the image stabilizer is determined This function is effective for the case that the camera is in
41. usted In such a case PUSH SW stays reversely highlighted 13 14 Manual fine adjustment of white balance The white balance is manually fine adjusted after white balance automatically adjustment in the automatic color temperature tracking mode ATW1 ATW2 or automatic white balance control mode AWC Follow the procedure below CAMERA SETUP screen Fine adjustment screen CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER OFF AGC ON HIGH SENS UP WHITE BAL DNR BW MODE AUTOT i VMD ATW1 1 RET TOP END RET TOP END Step 1 set WHITE BAL to ATW1 ATW2 or AWC and press the setting button The fine adjustment screen appears Step 2 Move the cursor to R and B and use the right or left button to fine adjust the level for each When the level indicator moves in the direction the color becomes deeper and when the level indicator moves in the direction the color becomes lighter 7 Digital noise reduction function setting DNR The digital noise reduction function reduces noise automatically under the condition of low illuminance The effect level of the noise reduction function is selectable from the following LOW Low level of noise reduction small residual image HIGH default High level of noise reduction large residual image 8 Black and white mode setting BW MODE The settings relating to the black and white mode can be configured Follow the procedure below Importa
42. usts the iris in accordance with the bright area Conversely adjusting the lens brightness for the darker areas causes the brighter areas to become washed out The SUPER DYNAMIC function digitally combines an image that is set up for a clear view of the brighter areas with an image that is set up for a clear view of the darker areas creating a final image that preserves overall detail Creates a clearer image by digitally combining images SUPER D5 setting When ALC ELC is set to ALC the SUPER D5 function is available Follow the procedure below CAMERA SETUP screen ALC CONT screen Area setting screen CAMERA SETUP ALC CONT 1 SCENE1 BACK LIGHT COMP ALC ELC ALC AREA 1 POSITION gt PUSH SW SHUTTER OFF SUPER D5 ON AGC ON HIGH SENS UP WHITE BAL DNR UPPER LEFT BW MODE AUTOT i VMD MANUAL ABS I DEL RET TOP END RET TOP END RET TOP END Step 1 Set ALC ELC to ALC and press the setting button The ALC CONT screen appears Note e When ALC ELC is set to ELC or ALC and the setting button is pressed the ELC CONT screen or ALC CONT screen appears e When ELC or ALC is selected the SUPER D5 function is disabled appears and OFF is selected 10 Step 2 Move the cursor to SUPER D5 and select the item from the following ON default Activates the SUPER D5 function all the time See below ON i VMD Activates the SUP
43. white frame on the SENSITIVITY screen e When appearance disappearance of a stationary object is detected a red frame will be displayed on the SENSITIVITY screen Set the detection areas Set the detection areas for motion detection and the detection of appearance disappearance of stationary objects Up to 2 detection areas can be set Follow the procedure below MOTION DET screen OBJECT DET screen Area setting screen MOTION DET 1 MOTION OFF LOITERING OFF DIRECTION OFF OBJECT DET 1 AREA 1 2 1 REMOVAL AND LEFT BEHIND POSITION PUSH SW DURATION TIME 10s AREA SETUP UPPER LEFT AREA SETUP SENSITIVITY SENSITIVITY DEL RET TOP END RET TOP END RET TOP END Step 1 Move the cursor to AREA and select SETUP and then press the setting button The AREA screen appears Step 2 Move the cursor onto the number to select the area number using the right or left button Step 3 Move the cursor to POSITION and press the setting button Step 4 Use the up down right and left buttons to determine the left upper position of the area to be set and press the setting button Note e The area corresponding to the selected number will be displayed in a green frame while the other set areas are shown in a white frame Step 5 Use the up down right and left buttons to determine the right lower position of the area to be set and press the setting button The asterisk mark will

Panasonic WV-CP500 Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents