Panasonic WV-CP300 Installation Guide
Contents
1. sise 29 Staridard accessories s sess ripe Re b poke kte b d ko akse b k ki EE 30 Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other appara tus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over 13 Unplug this apparatus during lightning storms2. Adjust the focus position so that the indicator value goes close to the PEAK HOLD position 6 When the indicator value goes to the best focus position BEST FOCUS will be displayed in reverse at the lower right corner of the screen Press the SET button again to close the FOCUS ADJUSTMENT menu No operation for 3 minutes also closes the menu 66 21 22 Important e If the view angle changes during adjustment press the SET button to close the FOCUS ADJUSTMENT screen once the view angle changes the PEAK HOLD and INDICATOR values will also change and repeat from step 3 after the view angle is fixed When shooting in the following place or following subjects press the S ET button again to close the FOCUS ADJUSTMENT screen Adjust to the best focus position while viewing the image Frequently moving subject Subject with large illuminance change Subject with low illuminance e Too bright or reflective subject Subject through a window Place where the lens easily becomes dirty e Subject with less contrast such as white wall Subject with remarkable depth Subject with heavy flicker Subject with horizontally parallel lines such as a shutter Performing each setting item in the setup menu should be completed in advance to use this unit Perform the settings for each item in accordance with the installation conditions and customer requirements List of setup men
3. AWG 16 24 Single core twisted Important Check whether the cord core is fully inserted into the power cord plug Ratings Power cord 24VAC 12VDC plug accessory PEN e GND 7 1 L e 1 8 to 1 4 inches 19 Tighten the screw of the power cord plug 4 Connect the power cord plug to the power supply terminal on the rear side of the camera Important Make sure that the power cord plug is inserted fully into the power supply terminal Cable length and wire gauge 24 V AC The recommended cable length and wire gauge are shown in the table for reference The voltage supplied to the power terminals of the camera should be within 19 5 V AC and 28 V AC The recommended wire size for 24 V AC power cord is shown below Copper wire 24 22 20 18 size AWG 0 205 mm 0 325 mm 0 519 mm 0 833 mm Length approx feet 66 100 150 250 395 12V DC Calculation of the relation among the cable length resistance and power supply The voltage supplied to the camera shall be between 10 8 V DC and 16 V DC 10 8V DC VA 2 RxIxL 16 V DC L Cable length m R Resistance of copper wire Q m VA DC output voltage of power supply unit DC current consumption A See specifications Resistance of copper wire at 20 C Copper wire 24 22 20 18 16 size AWG 0 205 mm 0 325 mm 0 519 mm 0 883 mm 1 307 mm 20 Resistance 0 083
4. Continuous SEITEC EINEN NENET Ble use of the damaged cord connector during use or plug may cause electric shock or di fire Disconnect the power plug immediately The temperature of power and request repair from your dealer cord rises or falls when the p power cord is bent or stretched during use Pp p Specifications General WV CP310 WV CP300 WV CP314 WV CP304 Power source 120 V AC 60 Hz 24 V AC 60 Hz 12 V DC Power consumption 1 9 W 24 V AC 2 3 W 12 V DC 210 mA Image sensor 1 8 type interline transfer CCD Effective pixels 976 H x 494 V Scanning area 4 8 mm H x 3 6 mm V 3 16 inches H x 5 32 inches V Scanning system 2 1 interlace Scanning line 525 lines Horizontal scanning frequency 15 734 kHz Vertical scanning frequency 59 94 Hz Synchronization Internal INT multiplexed vertical drive VD2 Horizontal resolution 650 TV lines Vertical resolution 350 TV lines Video output 1 0 V p p NTSC composite video signal 75 Q Signal to noise ratio 52 dB AGC OFF 0 08 Ix color mode Minimum illumination 0 008 Ix 0 05 Ix 0 008 Ix 0 05 Ix black and black and black and black and white mode white mode white mode white mode ALC lens drive DC drive Lens mount CS mount Ambient operating temperature 10 C to 50 C 14 F to 122 F Ambient operating humidity Less t
5. or DOWN button to move the cursor to END Step 2 Press the RIGHT button to move the cursor to SETUP and press the SET button to change the setup mode from DISABLE to ENABLE Step 3 Move the cursor to the item to be set and press the SET button Screenshot 3 The selected setup screen in the setup menu appears on the screen CAMERA SETUP SCENE1 ALC ELC SHUTTER AGC SENS UP ALC OFF ON HIGH OFF ATWI L HIGH AUTO11 OFF RET TOP END Note e f the top screen of the setup menu is called up with the operation buttons while the camera is operated the setup mode is always DISABLE to prevent operation errors To perform settings in the setup menu change the setup mode to ENABLE The cursor is a reversely highlighted part Step 4 Perform the settings for each item Selection of setting item Press the UP button or DOWN button to move the cursor Change of settings Press the RIGHT button or LEFT button Display of advanced setup screen Press the SET button when is attached to the target setting item Return to previous setup screen Move the cursor to RET and press the SET button Return to the top screen Move the cursor to TOP and press the SET button to display the top screen of the setup menu Step 5 Move the cursor to END and press the SET button to return to the camera image screen or wait ab
6. or less Optional dedicated lens Lens type Model No ALC lens for 1 3 type CCD cameras 2x vari focal WV LZA61 2S WV LZA62 2 A Connect the lens cable to the ALC lens connector of the camera ALC lens connector EEN ral a 6 3 Pin No 1 Dump Dump Drive Drive Q AJOJN 13 Installation of safety wire The following example shows the installation of safety wire Important Be sure to install safety wire between the camera and the installation position to prevent unex pected injury caused by fallen camera Ensure that the safety wire is installed Consult the dealer about installation Attach the safety wire lug accessory to the screw hole of the mount base with screw accessory Loosen one screw in the front portion of the accesso Important n camera upper case Either left or right Wire lug fixing Wire engaging hole Q Be sure to attach the safety wire lug accessory Sere m e with the wire lug fixing screw M2 5 x 8 mm Screws of T 5 16 inches provided in the accessories upper case ja Safety wire lug EN I MEUBLE LAM CN A e Be sure to attach the safety wire lug accessory with the screw provided in the accessories Using screw of different length may cause camera drop or damage Do not install the safety wire lug at places other than the two screw holes of the upper case Do not install the safety wire lug o
7. 0 052 0 033 0 020 0 0138 m 10 Adjust the camera angle by loosening the screw of the camera mount bracket while viewing the video monitor Be sure to loosen the screw of the camera mount bracket when the camera angle is adjusted If the camera angle is changed when the screw is tight excessive force is applied to the cam era mount bracket and camera and accordingly they may be damaged Be sure to tighten the screw securely after camera angle adjustment 11 Adjust the focus To use a fixed focal lens When adjusting the focus with a fixed focal lens use the back focus adjustment knob Adjust the focus with the focus assist function The view angle and aperture can be adjusted according to the distance of the photographic subject Adjust the view angle and focus when adjusting the camera angle D Loosen the zoom lock knob Adjust the view angle with the zoom and focus ring according to the FOCUS ADJUSTMENT photographic subject Tighten the zoom lock knob Press the SET button The FOCUS ADJUSTMENT screen will appear The focus assist function will be activated to perform INDICATOR 1135 BEST the optimum adjustment eie acu ke When the focus ring is positioned near the best focus position the position will automatically be memorized as the PEAK HOLD position the high er the value is the closer it is to the focus point 6 When the focus ring is moved the current focus position will be indicated on INDICA TOR
8. OSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY NY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION EING A PHOTOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF HAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME EASON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE A B 1 R Preface This product is a 1 3 type CCD color CCTV camera Connection of this product to a video monitor allows users to use this product as a monitoring camera WV CP310 120 V AC power supply with color black and white mode switch function e WV CP314 24 V AC 12 V DC power supply with color black and white mode switch function WV CP300 120 V AC power supply with easy black and white mode switch function e WV CP304 24 V AC 12 V DC power supply with easy black and white mode switch function About notations The following notations are used when describing the functions limited for specific models The functions without the notations are supported by all models D The functions with this notation are available when using the model WV CP310 and WV CP314 GD Th
9. P END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN e s I 160 AP GAIN PEDESTAL HUE PIX OFF COMMUNICATION COAX CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END 27 28 Troubleshooting Before asking for repairs confirm the causes with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below Cause solution Reference page C N A A Are the power cord and coaxial cable connected appropriately 19 20 P Check whether the connection is a appropriately established s the monitor brightness appropriately No image displayed adjusted or is the contrast appropriately adjusted Check whether the monitor settings are appropriate J a n b gt e Is the lens cap detached Check whether the lens cap is removed J d s C s the lens of the camera soiled with dirt or dust Check whether the lens of the camera is clean Blurred image s r A e Is the focus adjusted correctly Check if the focus is adjusted 21 22 correctly A V J a Oo T Damaged power cord sheathing kb gt D Heated portion of power line DUM The power cord power connector or consisting of power cord fi t d gt power plug is damaged
10. Panasonic Installation Guide Color CCTV Camera voan WV CP310 WV CP314 WV CP300 WV CP304 This illustration represents WV CP300 Lens Option Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual WARNING To prevent fire or electric shock hazard do not expose this apparatus to rain or moisture The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids such as vases should be placed on the appara tus All work related to the installation of this product should be made by qualified service personnel or system installers To prevent injury this apparatus must be securely attached to the floor wall ceiling in accordance with the installation instructions The mains plug or an appliance coupler shall remain readily operable The installation shall be carried out in accordance with all applicable installation rules This product has no power switch When turning off the power turn off a Power Supply or remove a power cable The connections should comply with local electri cal code For Canada This Class A digital apparatus complies with Canadian ICES 003 RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USE
11. R SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral trian gle is intended to alert the user to the presence of uninsulated dan gerous voltage within the prod uct s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte nance servicing instructions in the literature accompanying the appliance For U S A NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly app
12. ains how to install the camera Refer to the Operating Instructions PDF on the provided CD ROM for descriptions of how to perform the unit settings Adobe Reader is required to read PDF When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and registered trademarks Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or othe countries Precautions Refer installation work to the dealer Installation work reguires technigue and expe riences Otherwise injury or damage to this product may result Be sure to consult the dealer Do not insert any foreign objects This could permanetly damage this product Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or elec tric shock Consult the dealer for the repair or inspections Stop operation immediately when some thing is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product continued use will result in fire injury or dam age to the product Turn the power off immediately and contact qualified service personnel for service Select an installation area that can support the total weight Selecting an inappropriate i
13. al 12V IN 24 V IN Only for WV CP304 WV CP314 The power supply of 24 V AC or 12 V DC is connected to this terminal Setup button SET Press the SET button once and the FOCUS ADJUSTMENT screen will be displayed Bottom view WV CP304 WV CP314 gt Hold down the SET button for more than 2 seconds and the setup menu screen will be displayed e LEFT RIGHT Press the RIGHT or LEFT button to move to the right or left in the menu or change the displayed values e UP DOWN Press the UP or DOWN button to move up or down in the menu UP UP LEFT Br RIGHT V DOWN SET The directions of UP DOWN LEFT and RIGHT are as shown when you are directly facing UP SET Press this button in the menu to confirm the selected value or function In addition this button is used to open submenus Installation and connection Important Follow the installation and connection procedure below to ensure safety KI Rotate the lens option clockwise slowly to mount the lens Important e CS mount lens can be used on this camera For use of C mount lens use the C mount adaptor option For prevention of damage to the camera body use a lens with protrusion of 5 5 mm or less from the flange surface Protrusion from mount 920 mm 25 32 inches or less Protrusion from flange 5 5 mm 7 32 inches
14. axial cable plays the role of camera drop prevention measures in case Installation sample on a ceiling Installation sample on a wall Camera mount The cable co shall be tied y to the camera A Safety wire swa mount bracket i A OREN by cable tie The cable shall be Safety wire s gt S tied to the camera y mount bracket by cable tie Camera mount bracket locally procured 18 E Turn on the power WV CP300 WV CP310 Use the power cord accessory to connect the power supply Important The included power cord is the dedicated power cord of this product Do not use it with other devices Power cord accessory 120 V AC 60 Hz 7 3431 MI ou o 120V 60Hz VIDEO OUT WV CP304 WV CP314 Caution ONLY CONNECT WV CP304 WV CP314 TO 24V AC OR 12V DC CLASS 2 POWER SUPPLY Important Use 24 V AC or 12 V DC power supply that is insulated from 120 V AC power he power supply is automatically switchover either 24 V AC or 12 V DC No setting is required with this camera Power supply 24 V AC or 12 V DC Loosen the screw of the power cord plug accessory 2 Connect the power supply of 24 V AC or 12 V DC to the power cord plug Strip the end of the wire by 3 mm to 7 mm and twist the stripped part of the wire sufficiently to avoid short circuit Specification of power cord wire
15. card esse ee emen The CD ROM contains the operating instructions and installation guide PDF The following parts are used during installation procedures Power cord only for WV CP300 and WV CP310 Approx 1 8 m 5 9 feet ies 1 pc Power cord plug only for WV CP304 and WV CP314 1 pc Safety wire lid EE OE ak Cea ka ka SR Oe EXEC Re koule 1 pc Safety wire Approx 300 mm 1 feet ese 1 pc Wire lug fixing screws M2 5 x 8 mm 5 16 inches 2 pcs including 1 for replacement Washer ps 1 pc Spring washer 1 pc 30 31 Panasonic System Communications Company of North America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2012 sC0112 1052 PGQX1142YA Printed in China
16. cleaning this product Otherwise it may cause discoloration 10 Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this docu mentation This product is designed to be used indoors This product is not operable outdoors Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner Otherwise it may cause deformation discoloration and mal function Keep the product away from water and moisture Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particu lar environment Make sure that the installation area is strong enough to hold the product such as a con crete ceiling e Install the camera in the foundation area of the architecture or where sufficient strength is assured e If a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced Avoid installing this product in the fol lowing locations Location where it may get wet from rain or water splash Locations where a chemical agent is used Such as a swimming pool e Locations subject to steam and oil smoke Such as a kitchen e Locations near flammable gas or vapor e Locations where radiation or x ray emis sions are produced e Location
17. e This product is designed to be used indoors This product is not operable outdoors This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity Recommended operating tem perature 35 C 95 F or lower Do not expose this product to direct heat sources such as a heater Handle this product with care Do not drop this product nor apply shock or vibration to this product Failure to observe this may cause trouble Noise on monitor This product is equipped with a super sensi tive CCD Therefore noise may appear on the monitor This phenomenon is not trouble Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight the color filter of the CCD may have deteriorated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period the discoloration may remain Do not aim this product at strong light sources A light source such as a spot light causes a blooming light bleeding or a smear vertical lines Smear Bright subject Blooming Cleaning this product body Turn the power off when cleaning this product Do not use strong abrasive detergent when
18. e functions with this notation are available when using the model WV CP300 and WV CP304 Features Introduction of newly developed high resolution CCD The introduction of the newly developed CCD with 976 horizontal pixels has led to a horizontal res olution of as high as 650 TV lines High sensitivity achieved because of noise reduction function Sensitivity at the following minimum illuminations has been accomplished for color images because of the introduction of low noise circuit design F1 4 0 08 Ix color 0 008 Ix black and white p gt 0 08 Ix color 0 05 Ix black and white qm Day Night conversion function equipped EgD No setup change is required at night because the image automatically changes from the color mode to the black and white mode at low illuminance Bright images can be captured at night because of automatic switching of IR filters at low illuminance Motion detection function VMD equipped The motion of an object is detectable The acts of covering the camera with a cloth a cap or other acts and changing the camera direction during surveillance can be detected Note he VMD function is not the dedicated function to prevent thefts fires etc We are not respon sible for any accidents or damages caused by applying the function for the above purposes About the user manuals The operating instructions of the camera consist of 2 sets this book and operating instructions PDF This book expl
19. ges vertically or horizontally UPSIDE DOWN LDC Adjusts the Lens distortion correction to convert the image so that it matches the square monitor SPECIAL Adjusts the chroma level color density CHROMA GAIN AP GAIN Adjusts the aperture level Adjusts the pedestal brightness level PEDESTAL HUE Adjusts the chroma phase hue Corrects image defects such as flaws PIX OFF COMMUNICATION Performs the communication setting of the system with a receiver into which this unit is integrated Restores the settings in the setup menu to the default settings CAMERA RESET SER NO LANGUAGE Displays the serial number of this unit Selects a language to be used in the setup menu 23 Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor The description below explains how to operate the setup menu basically Screenshots of WV CP310 are shown as an example Screenshot 1 Hold down the SET button for about 2 seconds to call up the top screen of the setup menu MODEL WV CP310 SERIES CAMERA ID OFF CAMERA L SYSTEM L SPECIAL LANGUAGE END SETUP DISABLE Screenshot 2 The setup mode changes to ENABLE and the setup menu becomes ready to be set MODEL WV CP310 SERIES CAMERA ID OFF L CAMERA L SYSTEM L SPECIAL LANGUAGE END SETUP ENABLE Step 1 Press the UP
20. han 90 Yo 101 mm L x 72 mm W x 55 mm H 81 mm L x 72 mm W x 55 mm H Dimensions 8 31 32 inches L x 2 27 32 inches 3 3 16 inches L x 2 27 32 inches x 2 5 32 inches H W x 2 5 32 inches H Mass Approx 190 g 0 42 Ibi Approx 160 g Power cord excluded 0 35 Ibf Chinese up to 8 characters English letter numbers and symbols Camera title up to 16 characters Light control mode setting ALC ALC ELC Back light compensation ON OFF Auto black stretch ON OFF Shutter speed 1 10000 1 120000 s OFF 1 60 1 100 1 250 1 500 1 1000 1 2000 1 4000 Auto gain control ON HIGH MID LOW OFF Sensitivity up x32 x64 x128 x256 x512 OFF AUTO x2 x4 x6 x10 x16 x32y FIX x2 x4 x6 x10 x16 White balance ATW1 ATW2 AWC Digital noise reduction LOW HIGH Day amp Night IR AUTO1 AUTO2 ON OFF ED Day amp Night Electronic AUTO OFF ED 29 WV CP310 WV CP300 WV CP314 WV CP304 Video motion detection OFF MOTION DETECTION SCENE CHANGE Number of scene file 2 Privacy zone ON 1 ON 2 OFF mage stabilizer ON OFF Electronic zoom ON up to 2x OFF Upside down ON OFF Lens distortion correction O to 255 X Values of weight and dimensions are approximate The specification is subject to change with out notice Standard accessories Installation Guide this book Warranty
21. mounted Screw tightening The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area Do not use an impact driver Failure to observe this may cause overtightening and consequently damage to the screws When a screw is tightened make the Screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure tightening is enough and there is no backlash Power cord only for WV CP300 WV CP310 Connect the power cord securely Run the power cord so that no load is applied to the cord when panning or tilting the camera Failure to observe this may disconnect the power cord and accordingly no image is dis played 11 Major operating controls and their functions 12 Side view 6 o A a Rear view lt WV CP300 WV CP310 gt A Ox o VIDEO OUT ED 120V 60Hz D AC power input terminal 120 V 60 Hz Only for WV CP300 WV CP310 Connect with the supplied power cord Video output connector VIDEO OUT Provides video output to system units Tripod mount base This is used to install the camera onto the mount bracket locally procured ALC lens connector Connects to ALC lens 4 pin Back focus adjustment screw Adjusts the back focus distance and image focal length Power input termin
22. n the projec tions of the upper case Install the safety wire lug between the two projections e Recommended tightening torque 0 39 N m 0 29 lbf ft Engage the safety wire with the wire engaging hole Safety wire Wire engaging hole c D Pass one end of the safety wire eyelet through the wire engaging hole Pass the other end of the safety wire through the eyelet 14 El installation of camera mount bracket locally procured Secure the camera mount bracket locally procured to the installation position and mount the camera on the camera mount bracket Prepare mounting screws according to the material of the area where the camera mount bracket locally procured is to be installed The installation method may be different depending on the material of the area where the bracket is to be installed When installing on steel Fix with bolts and nuts M6 or M8 e When installing on concrete Fix with expansion anchor bolts M6 or M8 Use mount bracket with strength 5 times of the total weight of the camera body and lens The height and length of the camera mount bracket must be appropriate to ensure the use of the safety wire in the accessories The mounting conditions of the camera mount bracket locally procured are described as follows Installation Recommended Screw quantity Minimum pull out position screw strength per 1 pc On ceiling M6 or M8 3 pcs 196 N 44 06 Ibf On wall M8 4
23. nstallation surface may cause the product to fall down or topple over resulting in injury Installation work shall be started after suffi cient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents Consult the dealer for the inspections This product shall be installed in a vibra tion free place Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury Install this product in a location high enough to avoid people and objects from bumping the product Failure to observe this may cause a drop resulting in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause injury or fire Turn the power off when do wiring of this product Failure to observe this may cause electric shock A short circuit or wrong wiring may cause fire Do not use this product in an atmosphere of flammable gases Failure to observe this may cause injury by explosion Avoid installing this product in locations where it is subject to damage by salt or corrosive gas Otherwise the mounting fixtures will deterio rate causing the product to fall down and leading to accidents Tighten screws and mounting fixtures to the specified torque Failure to observe this may cause a drop resulting in injury or accidents Precautions for us
24. or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPECIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 3 UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY TH USER 4 INCONVENIENCE OR ANY L
25. out 5 minutes and the setup menu will automatically close 25 26 Screen transition diagram zip Top screen MODEL WV CP310 SERIES CAMERA ID CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE OFF CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ Q amp dli SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC I OFF ON HIGH OFF ATWI L HIGH D amp N IR AUTO1 VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC PRIVACY ZONE STABILIZER EL ZOOM UPSIDE DOWN LDC RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN seel 160 AP GAIN PEDESTAL HUE PIX OFF COMMUNICATION COAX CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END Screen transition diagram E Top screen MODEL WV CP300 SERIES CAMERA ID CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE OFF I CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ Q amp dli SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC OFF ON HIGH OFF ATWI I HIGH D amp N ELE OFF VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC PRIVACY ZONE STABILIZER EL ZOOM UPSIDE DOWN LDC RET TO
26. pcs 921 N 207 05 lbf Important e Refer to the operating instructions of the camera mount bracket locally procured for the mounting angle of the camera mount bracket for a ceiling or wall When the camera mount bracket is mounted on a wall be sure to observe the mounting height described on the illustration Installation sample on a ceiling Installation sample on a wall Camera mount bracket 7 locally procured Screws _ 8 9 feet FI locally procured a Screws locally procured 15 16 E Mount the camera on the camera mount bracket Follow the instruction of camera mount bracket to mount the camera on the camera mount bracket and aware of the followings Be sure to install the tripod mount base and safety wire before attaching the camera to the camera mount bracket Change the tripod mount base position when attaching the camera to the ceiling mount bracket Observe the following precautions at this time If it is needed to restore the tripod mount base to its original position also observe the fol lowing precautions When attaching an optional tripod mount base on the top or bottom of the camera use the removed screws to attach the tripod mount base Use of longer or shorter screws may cause the camera or tripod to fall causing damage Recommended tightening torque 0 39 N m 0 29 Ibf ft Installation sample on a ceiling Tripod socket Screws hole 1 4 20UNC Tri
27. pod mount base on the mount base should point forward 3 Attach safety wire accessory to the ceiling or wall Attach the safety wire to the foundation or other parts of the building with sufficient strength minimum pull out strength 196 N 44 06 Ibf Prepare screws according to the condition of the attachment position Use the safety wire accessory washer accessory and spring washer accessory When attached to the wall Recommended screw M4 minimum pull outstrength Spring washer Washer 196 N 44 06 Ibf accessory accessory Safety wire accessory Foundation or other parts of the building with Sufficient strength When attached to the ceiling Ceiling ESQ A 15 Washer accessory Spring washer accessory Recommended screw M4 minimum pull out strength 196 N 44 06 lbf Safety wire accessory 17 Connect the video output Important Be sure to turn off the power of each device before connecting Be sure to secure the coaxial cable connectors Connect a coaxial cable locally procured to the video output connector Coaxial cable Ws em To video input oo 120V 60Hz Oo VIDEO OUT Fl Use a cable tie locally procured to attach the coaxial cable to the camera mount bracket Important The cable tie shall be made of metallic or durable material to be strong enough because the co
28. roved by the party responsible for compliance could void the user s authority to operate this equipment For U S A The model number and serial number of this product may be found on the surface of the unit You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No Contents Iraportantsafety InstuCtiO S t 2 swete AE an Y Red un EXER SERT in kr op e cad an p ia sees 4 Leinmnitation OT lol t E 5 DISCIAIMEH of EO RE OE SM ex ee pr e rest npe Rt vnb XL IG 5 stele e P E 6 ADOULINOLALOMS repaso pai espe bu p Page ERR DR OE ER nep EN 6 zu S m 6 ABOUT THe USSR MANUALS N TEE 7 Trademarks and registered trademarks ssssssssssseeeeeeenene nennen nennen nnns 7 eie REM RE N RE OE ER ER EE 8 Pr autionsfor InstellatiOnks esiste oret e ebd a Ee Ee ie kn fab ee De bee bab ARE ee 10 Major operating controls and their functions esse RR AR aea aaia aaa ee ee ee 12 IS ile as elek ea Seile ee 13 ede lt IE via kaka DO List of setup menu aid Basic operation ssss ed Screen transition diagram gg 126 Screen transition diagram Eg sanl Z Troubleshooting sa Specifications
29. s where corrosive gas is produced Locations where it may be damaged by briny air such as seashores Locations where the temperature is not within 10 C to 50 C 14 F to 122 F e Locations subject to vibrations This prod uct is not designed for on vehicle use e Locations subject to condensation as the result of severe changes in temperature Avoid moist or dusty places to install this system Otherwise lifetime of the internal parts may be shortened Avoid installing this product in a place with a high level of noise Installation near an air conditioner an air cleaner a vending machine or the like causes noise Avoid installing and connecting during a lightning storm Otherwise an electric shock or fire may be caused Be sure to remove this product if it is not in use Do not damage the power plug or cable Keep the camera cable away from the lighting cable Failure to observe this may cause noise Radio interference When the camera is used near TV radio antenna strong electric field or magnetic field near a motor or a transformer images may be distorted and noise sound may be pro duced In such a case run the camera cable through specialized steel conduit tubes Locally procure the screws Screws are not supplied with this product Prepare the screws according to the material Structure strength and other factors of the mounting area and the total weight of objects to be
30. u Setup item CAMERA ID Description This item specifies the camera title The camera title that indicates the CAMERA camera location and other information about the camera is created with alphanumeric characters and symbol and then displayed on the screen Performs the camera operation settings Selects a scene file It is possible to register and save the settings as a SCENE 1 SCENE 2 ALC ELC scene file in case that it is necessary to change the settings such when shooting at night Selects the method of controlling the quantity of light in accordance with the lens to be used Specifies the electronic shutter speed SHUTTER AGC Specifies gain adjustment Specifies electronic sensitivity enhancement SENS UP WHITE BAL DNR Specifies white balance adjustment Selects the level of the digital noise reduction function Performs each setting regarding the black and white mode such as D amp N IR T m switching between color and black and white images Performs settings regarding VMD Video Motion Detection VMD Performs the settings regarding the camera system such as SYSTEM synchronization and privacy zone Specifies the synchronization type SYNC PRIVACY ZONE Hides undesired portions in the camera shooting area Decides whether or not to enable the image stabilizer STABILIZER EL ZOOM Switches the electronic zoom on and off Flips the camera ima
Download Pdf Manuals
Related Search