Panasonic WV-CF300 Installation Guide
Contents
1. 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REASON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE Preface This product is a 1 3 type CCD color CCTV camera Connection of this product to a video monitor allows users to use this product as a monitoring camera e WV CF374E with color black and white mode switch function e WV CF354E with easy black and white mode switch function and focus adjustment function e WV CF344E with easy black and white mode switch function About notations The following notations are used when describing the functions limited for specific models The functions without the notations are supported by all models EP The functions with this notation are available when using the model WV CF374E EZ The functions with this notation are available when using the model WV CF354E GED The functions with this notation are available when using the model WV CF344E Introduction of newly developed high resolution CCD The introduction of the newly developed CCD with2. SCENE1 ALC ELC ALC SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATWI DNR HIGH DSN ELE OFF VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN LDC RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN eec I 16 AP GAIN sa PEDESTAL PIX OFF I CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH 30 Troubleshooting Before asking for repairs confirm the causes with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below Cause solution Reference page C N C N Are the power cord and coaxial cable connected appropriately p Check whether the connection is 19 16 appropriately established J b s the adjustment monitor connected p Confirm whether the monitor is con 18 nected ja No image displayed e Is the monitor brightness appropriately adjusted or is the contrast appropriately p adjusted Check whether the monitor settings are L appropriate J e Is the cushioning material in the spherical cover removed Confirm whether the cushioning material has been removed pa e Is the spherical cover dirty or damaged Verify the state of
3. Subject with less contrast such as white wall Subject with remarkable depth Subject with heavy flicker e Subject with horizontally parallel lines such as a shutter Adjustment on WV CF354E gt D Loosen the zoom knob and adjust to the best view angle between TELE and WIDE Note The focus may not be adjusted smoothly when the zoom adjustment ring is extremely close to the end of W direction T direction At this time slightly adjust the zoom adjustment ring towards the T direction W direction and then adjust the focus Q Tighten the zoom knob 3 Rotate the front of the lens and adjust to the best view angle between NEAR and FAR Press the AF button on the side of the camera which will automatically focus Note The AF function is not available over the entire focus range Be sure to perform approxmate adjustment of the view angle before manual focusing and then press the AF button to enable the AF function For the following subjects select ELC control method and then manually adjust the focus Fast moving subject e Subject with significant illuminance change e Subject with low illuminance such as high beam light Too bright or reflective subject e Subject behind a window ess contrasty subject such as white wall e Subject with remarkable depth Subject with flicker Subject with parallel lines such as a shutter Blurred or dirty spherical cover 21 Atta
4. facing the direction opposite to the TOP arrow of the installation mark BFRONT direction of the installation template label in the accessories When attached to the wall Install the camera with the TOP arrow of the installation mark facing upward 17 18 Connect the 23 5 mm miniature plug mono channel to the adjustment monitor output jack Important e This video output is intended for confirmation of view angle etc during installation or repair service and not for recording or monitoring Note e Video cannot be output through the video output cable after connecting the adjustment monitor Pan tilt and azimuth adjustment Important e When adjusting pan tilt or azimuth do not hold the lens of the camera CD Adjustment of panning position Original position mark Loosen the panning table lock screw and rotate the table to determine the panning position adjustable range 350 Panning table e The panning position can be adjusted between 180 clockwise and 1 70 counter clockwise After the panning position is determined fix the panning table with the panning table Counter i lock screw clockwise 170 Clockwise 180 Recommended torque 0 39 N m Panning table lock screw LOCK Q Adjustment of tilting position Turn the tilting table to adjust the tilting position of the camera adjustable range 90 e
5. 976 horizontal pixels has led to a horizontal res olution of as high as 650 TV lines High sensitivity achieved because of noise reduction function Sensitivity at the following minimum illuminations has been accomplished for color images because of the introduction of low noise circuit design Lens built in F1 3 0 08 Ix color 0 008 Ix black and white GD 0 08 Ix color 0 05 Ix black and white GD GD Day Night conversion function equipped ZZ No setup change is required at night because the image automatically changes from the color mode to the black and white mode at low illuminance Bright images can be captured even at night because of automatic switching of IR filters at low illuminance Focus adjustment function equipped ED Auto focus is achieved at installation of the camera or through menu operation Motion detection function VMD equipped The motion of an object is detectable The acts of covering the camera with a cloth a cap or other acts and changing the camera direction during surveillance can be detected Note e The VMD function is not the dedicated function to prevent thefts fires etc We are not responsible for any accidents or damages caused by applying the function for the above purposes About the user manuals The operating instructions of the camera consist of 2 sets this book and operating instructions PDF This book explains how to install the camera Refer to the Operation Inst
6. AE PA e DA ek rade venete 24 zie M M EET 25 Screen transition diagram amp Q9 ssssssssssssseeeeneeee nennen nnne 2f Screen transition diagram GB 28 Screen transition diagram EDP in eeni aieeaa ainina ae enea E TT E EAEE ENE ATENE 29 MOUDIESASOUNO 222527 sip T M 30 SPSCMICAUNONS TES 31 Standard accessories nun eee aaa aaa aaa aaa taa aaa aa aa aaatooooottotetetaaeaaooooooooooeoeteeeeeeoooooooooooeoeeeooooe 32 Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 10 Only use attachments accessories specified by the manufacturer 11 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 12 Refer all servicing to qualified service personnel Servicing is re
7. Synchronization Internal INT Horizontal resolution 650 TV lines Vertical resolution 400 TV lines Video output 1 0 V p p PAL composite video signal 75 Q Signal to noise ratio 52 dB AGC OFF Minimum illumination 0 09 1x Color mode 0 008 Ix 0 05 Ix black and white mode black and white mode Lens 3 6x vari focal lens Focal length 2 8 mm to 10 0 mm Aperture ratio F1 3 WIDEto F3 1 TELE F1 3 WIDB to F3 0 TELE F1 3 WIDE to F3 1 TELE View angle WIDE HxV 100 8 x73 8 TELE HxV 27 6 x20 7 WIDE HxV 100 3 x73 4 TELE HxV 27 8 x20 9 WIDE HxV 100 3 x73 5 TELE Hx V 27 6 x20 7 Adjustable angle range Pan 180 to 170 Tilt 90 Azimuth 100 Ambient operating temperature 10 C to 50 C Ambient operating humidity Less than 90 Dimensions 2108 mm x 94 mm H Mass 320 g Camera title Chinese up to 8 characters English letter numbers and symbols up to 16 characters Light control mode setting ALC ALC ELC Back light compensation ON OFF Auto black stretch ABS ON OFF Shutter speed OFF 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 1 120000 5 Auto gain control ON HIGH MID LOW OFF Sensitivity up OFF AUTO x2 x4 x6 x10 x16 x32 FIX x2 x4 x6 x10 x16 x32 x64 x128 x256 x512 White balance ATW1 ATW2 AWC Digita
8. or water splash e Locations where a chemical agent is used Such as a swimming pool e Locations subject to steam and oil smoke Such as a kitchen ocations near flammable gas or vapor Locations where radiation or x ray emissions are produced e Locations where corrosive gas is produced Locations where it may be damaged by briny air such as seashores Locations where the temperature is not within 10 C to 50 C e Locations subject to vibrations This product is not designed for on vehicle use e Locations subject to condensation as the result of severe changes in temperature In case of installing the product in such locations the dome cover may become foggy or condensation may be caused on the cover Avoid moist or dusty places to install this system Otherwise lifetime of the internal parts may be shortened Avoid installing this product in a place with a high level of noise Installation near an air conditioner an air cleaner a vending machine or the like causes noise Avoid installing and connecting during a lightning storm Otherwise an electric shock or fire may be caused Be sure to remove this product if it is not in use Do not damage the power plug or cable Keep the camera cable away from the lighting cable Failure to observe this may cause noise Radio interference When the camera is used near TV radio antenna strong electric field or magnetic field near a mot
9. the spherical cover Se v s the focus adjusted correctly 20 21 Blurred image Check if the focus is adjusted correctly s the lens of the camera soiled with dirt or dust Check whether the lens of the camera is clean Vv Vv w Yy va w Si EY d s the connected system controller set to multiplexed vertical drive VD2 9 Check whether the connected system controller is set correctly Black line in image f Damaged power cord sheathing lt e The power cord or connector is damaged Continuous use of the damaged cord or connector may cause electric shock or fire B Turn off the power supply immediately and request repair from your dealer jo Heated portion of power line consisting of power cord and connector during use b The temperature of power cord rises or falls when the power cord is bent or stretched during use v vv Yy Specifications WV CF374E WV CF354E WV CF344E Power source 24 V AC 50 60 Hz 12 V DC Power consumption 24 V AC 2 1 W 12 V DC 180 mA Image sensor 1 8 type interline transfer CCD Effective pixels 976 H x582 V Scanning area 4 8 mm H x3 6 mm V Scanning system 2 1 interlace Scanning line 625 lines Horizontal scanning frequency 15 625 kHz Vertical scanning frequency 50 00 Hz
10. C INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN LDC RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN sess I1 160 AP GAIN aa ss 32 PEDESTAL ewo LS PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END Screen transition diagram ED Top screen CAMERA ID screen MODEL WV CF354 CAMERA ID CAMERA ID OFF L 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPORSTUVWXYZ SPECIAL LANGUAGE SPACE POSI RET TOP END RESET END SETUP DISABLE CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC 1 SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATW1 DNR HIGH DSN ELE OFF VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN LDC i FOCUS ABF gt PUSH RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN eO I 16 AP GAIN sa PEDESTAL PIX OFF CAMERA RESET PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH 28 Screen transition diagram ED Top screen CAMERA ID screen MODEL WV CF344 CAMERA ID CAMERA ID OFF L 0123456789 CAMERA L ABCDEFGHIJKLM SYSTEM L NOPQRSTUVWXYZ SPECIAL L 2 HELPS LANGUAGE SPACE POSI RET TOP END RESET END SETUP DISABLE CAMERA SETUP screen CAMERA SETUP
11. Panasonic Installation Guide Color CCTV Camera Model No WV C F3 4 E WV CF354E WV CF344E Panasonic WV CF344 This illustration represents WV CF344E Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004 108 EC Vi deklarerar h rmed v rt fulla ansvar f r att den produkt till vilken denna deklaration hanvisar ar i verensst mmelse med standarddokument eller annat normativt dokument som framst lls i direktiv 2004 108 EC Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende norm of ander normatief dokument overeenkomstig de bepalingen van Richtlijn 2004 108 EC IImoitamme yksinomaisella vastuullamme ett tuote jota tama ilmoitus koskee noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa jotka noudattavat direktiivin 2004 108 EC s d ksi Vi erkleerer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standard eller andre normative dokumenter i f lge bestemmelserne i direktiv 2004 108 EC Vi erkleere
12. The view angle can be adjusted as the cam era uses vari focal lens e Tighten the tilting lock screw after adjustment Recommended torque 0 59 N m Adjustable range 90 Adjustment of azimuth Adjust the azimuth by rotating the azimuth adjuster adjustable range 100 azimuth adjuster Rotation me Rotation angle 100 angle 100 Note e Adjust azimuth so that the image top mark is facing A to display the image properly rather than upside down ASN TIP i Image top mark 19 Zoom and focus adjustment Perform the zoom and focus adjustments at the same time as pan and tilt adjustments Step 2 Note e f the camera is used in near horizontal position the shadow of the dome cover may appear in the image Adjustment on WV CF344E WV CF374E Lens FAR FOCUS ADJUSTMENT Focus knob INDICATOR 1135 BEST PEAK HOLD 1135 FOCUS CD Loosen the zoom knob and focus knob Select photographic subject and choose proper view angle through zooming Adjust the zoom and focus rings to make the image clear approximate adjustment Note The focus may not be adjusted smoothly when the zoom ring is extremely close to the end of W direction T direction At this time slightly adjust the zoom ring towards the T direction W direction and then adjust the focus Q Tighten the zoom knob 3 Press the SET button The FOCUS ADJUSTMENT sc
13. This item specifies the camera title The camera title that indicates the camera location and other information about the camera is created with alphanumeric characters and symbol and then displayed on the screen Performs the camera operation settings Selects a scene file It is possible to register and save the settings as a scene file in case that it is necessary to change the settings such when shooting at night Selects the method of controlling the quantity of light in accordance with the lens to be used Specifies the electronic shutter speed Specifies gain adjustment Specifies electronic sensitivity enhancement Specifies white balance adjustment Selects the level of the digital noise reduction function Performs each setting regarding the black and white mode such as switching between color and black and white images Performs settings regarding VMD Video Motion Detection Performs the settings regarding the camera system such as synchronization and pri vacy zone Only INT method can be used VD2 synchronization cannot be used Hides undesired portions in the camera shooting area Decides whether or not to enable the image stabilizer Switches the electronic zoom on and off Flips the camera images vertically or horizontally Adjusts the lens distortion correction to convert the image so that it matches the square monitor Selects the adjustment method and fine adjustment method for focus Adjusts the chrom
14. a level color density Adjusts the aperture level Adjusts the pedestal brightness level Corrects image defects such as flaws Restores the settings in the setup menu to the default settings Displays the serial number of this product Selects a language to be used in the setup menu Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor The description below explains how to operate the setup menu basically Screenshots of WV CF354E are shown as an example Screenshot 1 Hold down the SET button for about 2 sec Step 1 onds to call up the top screen of the setup Press the UP or DOWN button to move the menu cursor to END Step 2 MODEL WV CF354 CANET GEER Press the RIGHT button to move the cursor REE to SETUP and press the SET button to LANGUAGE change the setup mode from DISABLE to ENABLE END SETUP DISABIE Screenshot 2 Step 3 The setup mode changes to ENABLE and the setup menu becomes ready to be set Move the cursor to the item to be set and press the SET button MODEL WV CF354 CAMERA ID OFF I CAMERA SYSTEM SPECIAL L LANGUAGE L END SETUP ENABLE 25 26 Screenshot 3 The selected setup screen in the setup menu appears on the screen CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER OFF AGC ON HIGH SENS UP D amp N ELE VMD RET TOP END Not
15. ble resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappro priate waste handling Please contact your local authority for further details of your nearest desig nated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal 33 34 35 Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg F R Germany Panasonic System Networks Co Ltd 2012 sC1211 3052 PGQX1143WA Printed in China
16. camera to a wall or ceiling according to the material of the installation area Do not use wood screws and nails For mounting a camera on a concrete wall or ceiling use an anchor bolt M4 for securing Recommended tightening torque M4 1 6 N m Required pull out strength of a single screw bolt is 196 N or more e f a ceiling board such as plaster board is too weak to support the total weight the installation area shall be sufficiently reinforced e The protection sheet attached to the dome section should be peeled off after installation The mounting conditions of the camera are described as follows Installation Applicable mount Recommended Number Minimum pull out place bracket screw ofscrew strength per 1 pc Ceiling wall ia ne DX Ma 2 pcs 196N Ceiling wall Direct mounting MA 2 pcs 196 N Ceiling WV Q174E approx 310 g 1 Make sure that the installed mount bracket can support more than 5 times of the weight of the cam era H Remove the dome cover D Peel off the protection sheet from the dome cover Don t remove completely as this protects the dome during installation Q Loosen the dome cover fixing screw veso SIuoseued 3 Adjust the mark on this unit to on the dome cover and turn the dome cover counterclockwise to remove it Note The clear dome cover and the inner dome are joined into a single unit Therefore never try to remove them 13 14 ll Ab
17. ching the dome cover Align the mark with on the dome cover Melle and then install the dome cover Adjust the orientation of the dome cover Turn the enclosure clockwise so that the mark aligns with Turn the dome cover to the left or right while viewing the monitor so that the light is not blocked Mark I Important e Be sure to align the mark with when adjusting the dome cover Do not apply excessive force or you may cause damage Turn the dome cover clockwise so that the mark aligns with Fix the dome cover and camera body with the dome cover fixing screw M3 Recommended torque 0 59 N m After finishing the installation completely peel off the protection sheet that had been retained on the camera A Press the AF button again to adjust the focus GD For more information refer to page 21 fixing screw M3 AF button 23 24 Performing each setting item in the setup menu should be completed in advance to use this unit Perform the settings for each item in accordance with the conditions of the camera shooting area List of setup menu Setup item CAMERA ID CAMERA SCENE 1 SCENE 2 ALC ELC SHUTTER AGC SENS UP WHITE BAL DNR D amp N IR ELE VMD SYSTEM SYNC PRIVACY ZONE STABILIZER EL ZOOM UPSIDE DOWN LDC FOCUS GD SPECIAL CHROMA GAIN AP GAIN PEDESTAL PIX OFF CAMERA RESET SER NO LANGUAGE Description
18. e e f the top screen of the setup menu is called up with the operation buttons the setup mode is always DISABLE to prevent operation errors To perform settings in the setup menu change the setup mode to ENABLE The cursor is a reversely highlighted part Step 4 Perform the settings for each item Selection of setting item Press the UP or DOWN button to move the cursor Change of settings Press the RIGHT or LEFT button Display of advanced setup screen Press the SET button when j is attached to the target setting item Return to previous setup screen Move the cursor to RET and press the SET button Return to the top screen Move the cursor to TOP and press the SET button to display the top screen of the setup menu Step 5 Move the cursor to END and press the SET button to return to the camera image screen or wait about 5 minutes and the setup menu will automatically close Screen transition diagram ED Top screen CAMERA ID screen MODEL WV CF374 CAMERA ID CAMERA ID OFF 0123456789 CAMERA ABCDEFGHIJKLM SYSTEM NOPQRSTUVWXYZ SPECIAL Q0 amp di LANGUAGE 5 SPACE POSI RET TOP END RESET END SETUP DISABLE CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC L SHUTTER OFF AGC ON HIGH SENS UP OFF WHITE BAL ATWI 1 DNR HIGH D amp N IR AUTO1 VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYN
19. h the camera with 2 screws M4 locally procured Recommended screw M4 2 pcs 885 Installation template m label accessory deem Side cable SA SEAT access hole a Cable mounting hole q in ceiling or wall A fe C Screws M4 locally procured Bl Connections Connect the video output Video output connector Power cord Important Be sure to turn off the power of each device before connecting Be sure to secure the coaxial cable connectors Connect a coaxial cable locally procured to the video output connector O3 5 Connect the power supply B Connect the two color conductor cable of the camera to the power supply The colors and functions of the conductors are shown below Color 12V DC 24 V AC Brown Positive Live Blue Negative Neutral 15 16 Important e The power supply of 24 V AC 12 V DC shall be insulated against 220 to 240 V AC e The power supply is automatically switchover either 24 V AC or 12 V DC No setting is required with this camera Connection of power cord When connecting the power cord use connectors that are designed for the power cord and be careful not to let the power cord fall off In addition waterproofing work is needed at the joint e g wrapping waterproof tape around the joint Cable length and wire gauge 24 V AC The recommended cable length and wire gauge are shown in the table for reference The voltage s
20. l be carried out in accordance with all applicable installation rules This product has no power switch When turning off the power turn off a Power Supply or remove a power cable The connections should comply with local electrical code Contents Important safety IAStAUCHUONS swivi exei nere ka kaki pit nk ii ak A kip it n ti a Wi ak to ni a ta ki ki k 4 HUAI OF OT NAN I AE 5 Disclaimer OF WAAN ecn wi a ai ini ei all dalle ak t k 5 IE TREE EI 6 ADOUE NOTIONS nennen kk won pani ka ek a n e e l ak yo e n e a e a n ki a n i cas te evanken adnate danse 6 EGQAUAOS vi kin pike ki 6 About the user TMANVALS sex ne cori enc l a pan e ed eee DA pec b de tus 7 Trademarks and registered trademarks Precautlons eeepc Precautions for installation Major operating controls and their functions Preparations cicer b erede Remove the dome cover About the side cable access hole Installationgmetho d OF CAMBENA sio civ x terre tira eere pea ak ka de andante AERAN EEP EA AAAA X ES SEMEN kad 4 GONNSCHONS e 15 IAS TENTION NT 17 ACUSEMEN raven kk 18 Attaching the dome COVE tags day vwa cest iuret o EE Dre em kr EE e an d an ea de ke zo se sad 22 SOU PANNO NM me r eet kipa 24 LIST OF SOTANANE NW ken ep kai la kk ka e mol it k e te a pop pt l e ER pe Yo ee
21. l noise reduction LOW HIGH 31 32 WV CF374E WV CF354E WV CF344E Day amp Night IR AUTO1 AUTO2 ON OFF GD Day amp Night Electric AUTO OFF CD GD Video motion detection OFF MOTION DETECTION SCENE CHANGE Number of scene file 2 Privacy zone ON 1 ON 2 OFF Image stabilizer ON OFF Electronic zoom ON up to 2x OFF Upside down ON OFF Lens distortion correction O to 255 Focus G gt ABF MANUAL x Values of weight and dimensions are approximate The specification is subject to change without notice Standard accessories Installation Guide this book nnee 1 pc The CD ROM contains the operating installations and installation guide PDF The following is used during installation procedures Installation template label ennen 1 pc Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis E Alternatively in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product Disposing of this product correctly will help to save valua
22. onds and the setup menu will be displayed e LEFT RIGHT Press the RIGHT or LEFT button to move to the right or left in the menu or change the displayed values e UP DOWN Press the UP or DOWN button to move up or down in the menu This illustration represents WV CF344E SET Press this button in the menu to confirm the selected value or function In addition this button is used to open submenus 9 Adjustment monitor output jack Connect the adjustment monitor small LCD monitor etc to the adjustment monitor output jack to adjust the camera angle Panning table lock screw LOCK Locks the panning position after adjustment Azimuth adjuster Adjusts the azimuth angle of the camera 2 Tilting table Adjusts the tilting position of the camera 3 Panning table Adjusts the panning position of the camera Cable access hole 5 Power cord Supplies 24 V AC or 12 V DC from an external power source Dust guard cap A rubber cap which prevent dust go into the camera through the cable access hole Fingerplate This is where to put your fingers when removing the dome cover When installing the camera on a wall or ceiling there are three methods as specified below e Use the one gang junction box e Installing the camera directly on a wall or ceiling e Using the optional ceiling mount bracket WV Q174E for embedded installation on a ceiling Important e Procure 2 screws M4 to secure the
23. or or a transformer images may be distorted and noise sound may be produced In such a case run the camera cable through Specialized steel conduit tubes Locally procure the screws Screws are not supplied with this product Prepare the screws according to the material structure strength and other factors of the mounting area and the total weight of objects to be mounted Screw tightening e The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area e Do not use an impact driver Failure to observe this may cause overtightening and consequently damage to the screws When a screw is tightened make the Screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure tightening is enough and there is no backlash 11 Major operating controls and their functions Video output connector Transmits composite video signals Mark This mark is used when the dome cover is installed G Lens Focus knob with lock function GD GD Locks the focus position after focus adjustment Zoom knob with lock function Locks the zoom position after zoom adjustment 6 Tilting lock screw Fixes the tilting position AF button AF EY ie page 21 Setup button SET Press the SET button once and the FOCUS ADJUSTMENT screen will be displayed GD GED Hold down the SET button for more than 2 Sec
24. out the side cable access hole If you choose not to drill hole in the wall or ceiling but to wire the camera with the cable exposed cut the cable access hole on the side of the dome cover to provide a cable entry Precautions when wiring from the side e Remove the dust guard cap Run the cable through the cable access hole and bend it inward then reinstall the dust guard cap Move the cable to one side as shown Be careful not to pinch the cable with the dome cover B Installation method of camera Using a gang junction box locally procured When using a gang junction box 101 6 mm x 60 3 mm procure one locally that meets the dimensions in the figure Next locally procure 2 camera mounting screws suitable for the installation surface and structure of the wall ceiling or gang junction box D Attach the gang junction box to the wall or ceiling Attach the camera to the gang junction box with the 2 screws locally procured 3 Tighten all mounting screws Side cable access hole Installation mark 83 5 mm Screws M4 locally procured Gang junction box locally procured Installing the camera directly on a wall or ceiling Affix the installation template label accessory to the ceiling or wall and use a pen to mark the positions of the screws and cable mounting hole in the ceiling or wall Remove the installation template label and attac
25. over resulting in injury Installation work shall be started after sufficient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents Consult the dealer for the inspections This product shall be installed in a vibration free place Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury Install this product in a location high enough to avoid people and objects from bumping the product Failure to observe this may cause a drop resulting in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause injury or fire Turn the power off when do wiring of this product Failure to observe this may cause electric shock A short circuit or wrong wiring may cause fire Do not use this product in an atmosphere of flammable gases Failure to observe this may cause injury by explosion Avoid installing this product in locations where it is subject to damage by salt or corrosive gas Otherwise the mounting fixtures will deteriorate causing the product to fall down and leading to accidents Tighten screws and mounting fixtures to the specified torque Failure to observe this may cause a drop resulting in injury or accidents Precautions for use This product is designed to be used indoors This prod
26. quired when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPECIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 3 UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT
27. r oss alene ansvarlige for at produktet som denne erkleeringen gjelder for er i overensstemmelse med folgende norm eller andre normgivende dokumenter som folger bestemmelsene i direktiv 2004 108 EC RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral trian gle is intended to alert the user to the presence of uninsulated dan gerous voltage within the prod uct s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte nance servicing instructions in the literature accompanying the appliance WARNING To prevent fire or electric shock hazard do not expose this apparatus to rain or moisture The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids such as vases should be placed on the apparatus All work related to the installation of this product should be made by qualified service personnel or System installers To prevent injury this apparatus must be securely attached to the floor wall ceiling in accordance with the installation instructions The installation shal
28. reen will appear The focus assist function will be activated to perform the optimum adjustment When the focus ring is positioned near the best focus position the position will automatically be memorized as the PEAK HOLD position the higher the value is the closer it is to the focus point amp When the focus ring is moved the current focus position will be indicated on INDICATOR Adjust the focus position so that the indicator value goes close to the PEAK HOLD position amp When the indicator value goes to the best focus position BEST FOCUS will be displayed in reverse at the lower right corner of the screen Press the SET button again to close the FOCUS ADJUSTMENT menu No operation for 3 minutes also closes the menu Important e f the view angle changes during adjustment press the SET button to close the FOCUS ADJUSTMENT screen once the view angle changes the PEAKHOLD and INDICATOR values will also change and repeat from step 4 after the view angle is fixed 20 Important e When shooting in the following place or following subjects press the SET button again to close the FOCUS ADJUSTMENT screen or adjust to the best focus position while viewing the image Frequently moving subject e Subject with large illuminance change e Subject with low illuminance Too bright or reflective subject Subject through a window Place where the lens easily becomes dirty
29. ructions PDF on the provided CD ROM for descriptions of how to perform the unit settings Adobe Reader is required to read PDF When the Adobe Reader amp is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and registered trademarks Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Precautions Refer installation work to the dealer Installation work requires technique and experiences Otherwise injury or damage to this product may result Be sure to consult the dealer Do not insert any foreign objects This could permanetly damage this product Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Stop operation immediately when something is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product continued use will result in fire injury or damage to the product Turn the power off immediately and contact qualified service personnel for service Select an installation area that can support the total weight Selecting an inappropriate installation surface may cause the product to fall down or topple
30. t Do not use strong abrasive detergent when cleaning this product Otherwise it may cause discoloration Synchronous mode setting Image synchronous mode of this camera indicates internal synchronization INT only Set the multiplexed vertical drive VD2 as OFF when the camera is connected to the system controller of the company 10 Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation This product is designed to be used indoors This product is not operable outdoors Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner Otherwise it may cause deformation discoloration and malfunction Keep the product away from water and moisture Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment Make sure that the installation area is strong enough to hold the product such as a concrete ceiling e Install the camera in the foundation area of the architecture or where sufficient strength is assured e f a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced Avoid installing this product in the follow ing locations e Location where it may get wet from rain
31. uct is not operable outdoors This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity Recommended operating temperature 35 C or lower Do not expose this product to direct heat sources such as a heater Handle this product with care Do not drop this product nor apply shock or vibration to this product Failure to observe this may cause trouble Do not touch the dome cover with your bare hands A dirty dome cover causes deterioration of picture quality Noise on monitor This product is equipped with a super sensitive CCD Therefore noise may appear on the monitor This phenomenon is not trouble Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight the color filter of the CCD may have deteriorated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period the discoloration may remain Do not aim this product at strong light sources A light source such as a spot light causes a blooming light bleeding or a smear vertical lines Smear Bright subject Blooming Cleaning this product body Turn the power off when cleaning this produc
32. upplied to the power terminals of the camera should be within 19 5 V AC and 28 V AC The recommended wire size for 24 V AC power cord is shown below Copper wire 24 22 20 18 16 size AWG 0 205 mm 0 325 mm 0 519 mm 0 883 mm 1 307 mm Length approx 12V DC Calculation of the relation among the cable length resistance and power supply The voltage supplied to the camera shall be between 10 8 V DC and 16 V DC 10 8 VDC lt VA 2 RxIxL x 16V DC L Cable length m R Resistance of copper wire Q m Va DC output voltage of power supply unit DC current consumption A See specifications Resistance of copper wire at 20 C Copper wire 24 22 20 18 16 size AWG 0 205 mm 0 325 mm 0 519 mm 0 833 mm 1 307 mm Resistance 0 083 0 052 0 023 0 020 0 013 O m Installation Installation of camera Turn off the power of all related devices before installation Remove the dome cover Connect all cables If necessary bind the cable with cable tie locally procured Install the camera The illustration below shows installation using a gang junction box locally procured Mount the camera with 2 screws M4 locally procured Installation Screws M4 locally procured Important e Be sure to avoid twisting the cables when tightening the screws Note e When attached to the ceiling Install the camera with its front Model number indication face
Download Pdf Manuals
Related Search