Panasonic CZ-CLNC1U Installation Manual
Contents
1. This network configuration determines the minimum interval that is secured for output network variables The network variables that are affected by this configuration are the following nvoOnOff_0 nvoOption1_0 nvoAlarmIn_0 nvoHeatCool_0 nvoAlarm_0 nvolnState_0 nvoSetpoint_0 nvoOption2_0 nvoSpaceTemp_0 Contents The valid range is 0 0 seconds to 6553 5 seconds The minimum time secured for transmission is independent for each network variable It is not valid between different network variables Pana_CZ CLNC1U_Engindd 14 3 14 2011 11 11 eu i 8 Locations Where Neuron ID is Applied The Neuron ID is applied in the following 3 locations 1 Packaging box 2 Top panel lid 3 On the main circuit board Neuron chip Neuron ID Nodeo 00 03 18 69 95 01 Node1 00 03 18 69 96 01 Node2 00 03 18 69 97 01 Node3 00 03 18 69 98 01 Main circuit board Neuron ID 00 03 18 69 95 01 Indoor unit Address Setting SW enabling SW SW i Pana_CZ CLNC1U_Engindd 15 5 15 2011 11 11 aasal Pana_CZ CLNC1U_Engindd 16 Printed in Japan 2011 11 11 vou2. For 17 or more groups of indoor units connect additional interface units e Install a remote controller or system controller etc which can control the A C units to an inter unit control wiring other than the LonWorks Interface unit e Before making the connection to the LonWorks Interface unit set the central control addresses in the indoor units i Pana_CZ CLNC1U_Engindd 2 5 2011 11 11 aaa Functions Settings for Temp setting 1 A C anit senings each group of rom the LonWorks indoor units Option 1 settings 2 Option 2 settings 2 Settings for all units Emergency stop i Option 1 settings 2 unit status notifications made to the LonWorks Option 2 settings 2 i 4 i i ings 7 3 Configuration properties Minimum time secured for transmission 8 Alarm status 3 6 1 When a temperature above the upper limit of the temperature which can be set by the indoor units has been specified it will be set to the upper limit conversely when a temperature below the lower limit has been specified it will be set to the lower limit 2 Two options can be selected using the setting switch from among remote controller prohibit fan speed setting air direction setting and filter sign 3 When indoor units are under group control an alarm is determined to have occurred when the alarm occurs at one or more of the units 4 The number of the indoor unit at which the alarm h
3. This input network variable is used to stop the indoor units in an emergency Remote controller prohibit start stop prohibit is enabled for the stopped indoor units The remote controller prohibit temperature setting operating mode status remains the same as before the units were stopped When emergency stop is canceled remote controller prohibit start stop prohibit status returns to the status prior to emergency stop however the unit itself remains stopped If this function is not used then it is not necessary to use this network variable 0 Cancel value Not used 1 Emergency stop Contents state nc49 Transmission interval setting network input config SNVT_time_sec nciSndHrtBt This network configuration sets the interval for automatic data output When the set time has elapsed data is output automatically The network variables that are affected by this configuration are the following nvoOnOff_0 nvoOption1_0 nvoAlarmIn_0 nvoHeatCool_0 nvoAlarm_0 nvolnState_0 nvoSetpoint_0 nvoOption2_0 nvoSpaceTemp_0 Contents The valid range is 0 0 seconds to 6553 5 seconds If 0 0 seconds is set automatic data update is disabled The transmission interval setting is the same for all network variables When the set time has elapsed above all network variables are output nc52 Setting of minimum time secured for transmission network input config SNVT_time_sec nciMinOutTm
4. i INSTALLATION INSTRUCTIONS Panasonic LonWorks Interface Model No CZ CLNC1U Contents 1 LonWorks Interface Overview 2 Product Overview System Diagram Functions 2 Installation Instructions of LonWorks Interface 4 Safety Precautions Included Parts Installation Method Wiring Specifications LonWorks Interface Structure Power Board Initial Settings 5 Power Board Wiring Wiring Procedure Main Circuit Board Indoor Unit Enabling Switches 6 Setting Switches Address Switches Communications LED Green 7 Data LED Red Diagram of External Dimensions D Product Specifications gt 3 Assigning Central Control Addresses 8 4 LonWorks Interface Test Run 9 5 Checking the LonWorks Interface Version 10 6 List of LonWorks Network Variables 11 Ta Details of LonWorks Network Variables 12 8 Locations Where Neuron ID is Applied 15 Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause har
5. Press the button and check that the display on the remote controller has been cleared remote controller For example in this case Indoor unit address 1 8 Central address 17 Pana_CZ CLNC1U_Engindd 8 Assigning Central Control Addresses 1 Turn the power switch S001 on the LonWorks Interface power board to OFF 2 Turn the setting switch S006 2 to OFF so that central control addresses are set with the DIP switches MULL S006 OFF 3 Set the first central control address with the address switch S005 When assigning serial numbers a consecutive series of numbers is assigned for the central control addresses lt Example gt If the first central control address is 5 then this circuit board assigns central control addresses 5 6 7 and 8 4 Make the enable disable settings with the indoor unit enabling switches S004 lt Example gt If central control addresses 6 and 8 do not exist enable only 5 and 7 5 is set as the central control 1234 address for indoor unit group 0 I I I I and 7 is set as the central S004 control address for indoor unit OFF group 2 SO X 5 Turn the power switch S001 on the LonWorks Interface power board to ON 2011 11 11 aaa i 4 LonWorks Interface Test Run Before performing a test run of
6. 8 PO L QL SL L B L L ce Ll v v9 Le v tv9 61 6 v9 6E 6 4 013 64 Product Specifications LonWorks network Connects to FTT 10 A transceiver device Power 100 120 200 240 V 50 60 Hz 1 PH Power 11 W max consumption Service environment conditions Temp 32 to 104 F humidity 20 to 80 Indoor use only External dimensions 3 7 64 in H x 19 11 16 in W x 8 15 32 in D Weight Approx 7 27 Ib 2011 11 11 aoa 3 Assigning Central Control Addresses e Before assigning central control addresses for the LonWorks Interface use the remote controller to make central control address settings for A C units e Follow only the steps for Assigning Central Control Addresses when a system controller or other central controller is already provided Setting Central Control Addresses 1 Press and hold both the and buttons for 4 seconds or longer Check that the SETTING display on the remote controller is flashing 2 Set the 03 item code by pressing the Ca and Cv temperature setting buttons 3 Set the desired central control address by pressing the and v J timer buttons 4 Press the button and check that the SETTING display stops flashing and illuminates instead The setting data cannot be changed unless the button is pressed 5
7. perform a test run to check for operating trouble As you do use the central control device Operating Instructions and explain operating procedures to the customer Then request that the customer store this manual together with the central control device Operating Instructions e Be sure to arrange installation from the dealer where the system was purchased or using a professional installer Electric shock or fire may result if an inexperienced person performs any installation or wiring procedures D incorrectly e Please install and ensure construction according to Installation Instructions of LonWorks Interface e Only a qualified electrician should attempt to connect this system in accordance with the instructions in this manual If the electrical circuit capacity is insufficient a danger of electric shock and fire may be present e Use the specified cables type and wiring diameter for the electrical connections and connect the cables securely Run and fasten the cables securely so that external forces or pressure placed on the cables will not be transmitted to the connection terminals Overheating or fire may result if connections or attachments are not secure Depending on the installation conditions and location an earth leakage breaker may be required If an earth leakage breaker is not installed there is a danger of electric shock or fire Included Parts Installation Instructions Pana_CZ CL
8. NC1U_Engindd 4 Installation Method e The screws used to install the main unit must be provided by the installer E e Install the LonWorks Interface away from any sources of electrical noise Wiring Specifications e For the inter unit control wiring use twin core AWG 20 AWG 14 cables e For the LonWorks communication line cables use twisted pair cables with a wire diameter of 0 51 mm AWG 24 or larger as recommended by Echelon Corp Examples of cables recommended by Echelon Corp Wire diameter Total cable length Cable type JAWG Bus type Free 24 AMG twisted pair 0 51 mm 900 m 450 m TIA568A category 5 24 2953 ft 1476 ft e Do not use the same cable for the inter unit control wiring the gt LonWorks communication lines and the power cable Do not run them through the same conduit or place the cables near one another e Connect the cables so that there is no miswiring Miswiring can cause malfunction LonWorks Interface Structure e This interface contains 4 LonWorks communication boards nodes e Up to 4 indoor unit groups maximum 32 units can be assigned to 1 node Main circuit board Node 3 Main circuit board Node 2 Main circuit oard Node 1 Main circuit board Node 0 Power transformer 2011 11 11 mag Power Board Initial Settings Wiring Procedure Not Install Ordinarily keep this set to Not Install initi
9. VT_temp_p Operating mode nvoHeatCool_00 SNVT_hvac_mode Option 1 status nvoOption1_00 SNVT_switch Output Option 2 status nvoOption2_00 SNVT_switch Alarm status nvoAlarm_00 SNVT_switch Indoor units with active alarms nvoAlarmIn_0O SNVT_switch Room temp nvoSpace Temp_00 SNVT_temp_p Indoor unit status nvolnState_00 SNVT_count Start stop nviOnOff_01 SNVT_switch Temp setting nviHeatCool_01 SNVT_temp_p Input Operating mode nviSetPoint_01 SNVT_hvac_mode Option 1 setting nviOption1_01 SNVT_switch Option 2 setting nviOption2_01 SNVT_switch Start stop status nvoOnOff_01 SNVT_switch Indoor group 1 Temp setting nvoSetPoint_01 SNVT_temp_p Operating mode nvoHeatCool_01 SNVT_hvac_mode Option 1 status nvoOption1_01 SNVT_switch Output Option 2 status nvoOption2_01 SNVT_switch Alarm status nvoAlarm_01 SNVT_switch Indoor units with active alarms nvoAlarmIn_01 SNVT_switch Room temp nvoSpaceTemp_01 SNVT_temp_p Indoor unit status nvolnState_01 SNVT_count Start stop nviOnOff_02 SNVT_switch Temp setting nviHeatCool_02 SNVT_temp_p Input Operating mode nviSetPoint_02 SNVT_hvac_mode Option 1 setting nviOption1_02 SNVT_switch Option 2 setting nviOption2_02 SNVT_switch Start stop status nvoOnOff_02 SNVT_switch Indoor group 2 Temp setting nvoSetPoint_02 SNVT_temp_p Operating mode nvoHeatCool_02 SNVT_hvac_mode Option 1 status nvoOption1_02 SNVT_switch Output Option 2 status nvoOption2_02 SNVT_switch Alarm status nvoAlarm_02 SNVT_switch Indoor units with active alar
10. Waiting for A C unit initial communication X A C unit initial communication in progress Low High LonWorks communication microcomputer error O EEPROM error X gt gt see Low 40 High O IO s s5s X Test run mode Low High Version display in progress O Normal communications in progress X Not lit Low Low speed flashing once second High High speed flashing O Constantly lit Data LED Red Data lllier Communications LED Data LED display meaning No LED lit All LEDs lit Displays the wait time seconds for A C unit initial communication Displays the A C unit communications status No LED lit No LED lit According to the test run mode specifications According to the version display specifications Displays the A C unit communications status D B e Display of A C unit communications status Indoor unit OFF Waiting for initial communication group Low speed flashing Waiting for minimum o3 o0 transmission interval oo4 1 High speed flashing Initial communication in progress oo 3 ON Normal communications in progress Illuminates for 200 ms when data is output to the 007 LonWorks communicator llluminates for 200 ms when data is output to the 008 f indoor outdoor communicator Diagram of External Dimensions Unit in ZE S l
11. al setting Install Free topology terminal resistor 51Q for the LonWorks communication lines Install lt gt Not Install N 7 4C o S002 i Power switch s001 E oFF Power board CNOO06 when AC 200 240V power is connected e Connect the power supply lines to the L and N power supply terminals the power suplly neutral to the N terminal e Connect an earth ground line to the screw lt OS Lon communication wiring VY AN ra N HAD AWIANLA when AC 100 120V power is connected VW UY oO 100 120 200 240 V 50 60 Hz 1 PH Power transformer primary side Conduit Power cables When AC 200 240V power is connected connect the power transformer primary side to CNO06 When AC 100 120V power is connected connect the power transformer primary side to CN005 It is connected to CNOO6 when the unit is shipped from the plant Inter unit control wiring Power Board Wiring Main Circuit Board LD001 LD008 lines 2 LON communication j line 2 reserve KA CN003 H LON communication w lines 1 Power board LON communication e line 1 reserve Inter unit control lines Inter unit control line reserve Earth for power wiring D La ia V iz LON communication s C i Neuron ID label COM Data oO jo00000 g s C m A S005 Address SW S006 Setting SW e The LonWorks communication lines can be connected to either 1 or 2 in the above figure The result
12. as occurred is notified This makes it possible to identify at which indoor unit of the indoor unit group the alarm has occurred When indoor units are under group control the room temperature of the main unit in the group is notified A When an alarm occurs at one or more indoor units the alarm code is notified as the indoor unit status All the data which can be output is output at the set interval The same data is not output continuously at the set interval 5 6 C7 8 i Pana_CZ CLNC1U_Engindd 3 5 2011 11 11 aa i 2 Installation Instructions of LonWorks Interface Safety Precautions The following is intended for the installer responsible for installation and test operations of the LonWorks Interface and should be carefully read before beginning The precautions given in this manual consist of specific Warnings and Cautions They provide important safety related information and are important for your safety the safety of others and trouble free operation of the system Be sure to strictly observe all safety procedures The labels and their meanings are as described below This symbol refers to a hazard or unsafe procedure or practice which can result in severe personal injury or death This symbol refers to a hazard or unsafe procedure or practice which can result in personal injury or product or property damage After installation is completed
13. fied it will be set to the upper limit conversely when a temperature below the lower limit has been specified it will be set to the lower limit Contents Valid range Auto heat cool mode 17 27 C 62 80 F Heat mode 16 26 C 60 78 F Cool mode 18 30 C 64 86 F Dry mode 18 30 C 64 86 F Fan mode Temp setting not used Temperature settings are made in units of 1 0 C 1 8 F Values after the decimal point are discarded Be aware that the temperature setting ranges may vary according to the models of the outdoor and indoor units nv4 Temperature setting status notification network output SNVT_temp_p nvoSetpoint_01 network output SNVT_temp_p nvoSetpoint_01 network output SNVT_temp_p nvoSetpoint_02 network output SNVT_temp_p nvoSetpoint_03 These output network variables are output when the temperature setting status is changed They are also output when the status has been changed from an A C unit side with the remote controller They are output when the LonWorks Interface or the A C unit power is reset Contents Valid range Output range Temp unit 16 30 C 60 86 F 1 0 C 1 8 F Be aware that the temperature setting ranges may vary according to the models of the outdoor and indoor units nv5 Operating mode setting command network input SNVT_hvac_mode nviHeatCool_00 network input SNVT_hvac_mode nviHeatCool_01 network input SNVT_hvac_mode nviHeatCool_02
14. m x 2 value 0 at all times state Contents Value 0 when no alarms are active nv13 Room temperature notification network output SNVT_temp_p nvoSpaceTemp_00 network output SNVT_temp_p nvoSpaceTemp_01 network output SNVT_temp_p nvoSpaceTemp_02 network output SNVT_temp_p nvoSpaceTemp_03 These output network variables are output when the indoor unit room temperature changes They are output when the LonWorks Interface or A C unit power is reset When indoor units are under group control the room temperature of the main unit in the group is output Contents Valid range Output range 35 0 92 5 C 31 198 F Temp units 0 5 C 0 9 F Be aware that the output temperature range may vary according to the models of the outdoor and indoor units When indoor units are under group control the status is output from the main unit nv14 A C unit status notification network output SNVT_count nvoInState_00 network output SNVT_count nvoinState_01 network output SNVT_count nvolnState_02 network output SNVT_count nvoinState_03 These output network variables are output when the A C unit status changes They are output when the LonWorks Interface or A C unit power is reset Normal communications in progress no alarms According to alarm code table Indoor unit not connected initial communication in progress nvi5 Emergency stop network output SNVT_switch nviAllInOff
15. mful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Caution To assure continued compliance follow the attached installation instructions Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment LonWorks is a registered trademark of the Echelon Corporation 8546436952601 1 Pana_CZ CLNC1U_Eng indd 1 5 2011 11 11 aa i 1 LonWorks Interface Overview Product Overview This interface is a communications interface for connecting LonWorks to an air conditioner unit control network From the host connected to LonWorks basic settings and status monitoring is possible for up to 16 groups of A C units System Diagram Outdoor Unit tee Indoor Unit Outdoor Unit Indoor Unit LonWorks communication line INV 4 LonWorks Interface _ Boe 97 Inter unit control wiring e Up to 16 groups of indoor units maximum 64 units can be controlled with 1 LonWorks Interface unit
16. ms nvoAlarmIn_02 SNVT_switch Room temp nvoSpaceTemp_02 SNVT_temp_p Indoor unit status nvolnState_02 SNVT_count Start stop nviOnOff_03 SNVT_switch Temp setting nviHeatCool_03 SNVT_temp_p Input Operating mode nviSetPoint_03 SNVT_hvac_mode Option 1 setting nviOption1_03 SNVT_switch Option 2 setting nviOption2_03 SNVT_switch Start stop status nvoOnOff_03 SNVT_switch Indoor group 3 Temp setting nvoSetPoint_03 SNVT_temp_p Operating mode nvoHeatCool_03 SNVT_hvac_mode Option 1 status nvoOption1_03 SNVT_switch Output Option 2 status nvoOption2_03 SNVT_switch Alarm status nvoAlarm_03 SNVT_switch Indoor units with active alarms nvoAlarmIn_03 SNVT_switch Room temp nvoSpaceTemp_03 SNVT_temp_p Indoor unit status nvolnState_03 SNVT_count Indoor groups 0 3 Input Emergency stop nviAlllnOff SNVT_switch Transmission intervals settings nciSndHrtBt SNVT_time_sec Minimum time secured for transmission nciMinOutTm SNVT_time_sec 11 2011 11 11 eu 7 Details of LonWorks Network Variables nv1 Unit start stop command network input SNVT_switch nviOnOff_00 network input SNVT_switch nviOnOff_01 network input SNVT_switch nviOnOff_02 network input SNVT_switch nviOnOff_03 These input network variables are used to change the start stop status of the indoor unit If start stop is only done from an A C unit side as with the remote controller then it is not necessary to use these network variables state C
17. n be selected remote controller prohibit fan speed setting air direction setting and filter sign reset Make changes using the DIP switches on the main circuit board They are output when the LonWorks Interface or A C unit power is reset State Wall Start stop Temp Operating operation setting mode EE i pw x 1 so o Remote controller prohibit O Permitted x Prohibited a ver Fan speed setting Air direction setting LG i Pana_CZ CLNC1U_Engindd 13 13 2011 11 11 aasal nv11 Alarm notification network output SNVT_switch nvoAlarm_00 network output SNVT_switch nvoAlarm_01 network output SNVT_switch nvoAlarm_02 network output SNVT_switch nvoAlarm_03 These output network variables are output when an alarm occurs at an indoor unit and when the alarm is reset at an indoor unit They are output when the LonWorks Interface or A C unit power is reset 0 Normal jvalue 0 at all times 1 Alarm Contents state nv12 Indoor unit number with active alarm notification network output SNVT_switch nvoAlarmin_00 network output SNVT_switch nvoAlarmin_01 network output SNVT_switch nvoAlarmin_02 network output SNVT_switch nvoAlarmIn_03 These output network variables are output when an alarm occurs at an indoor unit They are output when the LonWorks Interface or A C unit power is reset Indoor unit number with active alar
18. network input SNVT_hvac_mode nviHeatCool_03 These input network variables are used to change the indoor unit operating mode If the operating mode setting is only changed from an A C unit side as with the remote controller then it is not necessary to use these network variables Contents 0 Auto heat cool 5 Dry 1 Heat 9 Fan 3 Cool The operating modes that can be set may vary according to the models of the outdoor and indoor units Settings other than the above are ignored nv6 Operating mode status notification network output SNVT_hvac_mode nvoHeatCool_00 network output SNVT_hvac_mode nvoHeatCool_01 network output SNVT_hvac_mode nvoHeatCool_02 network output SNVT_hvac_mode nvoHeatCool_03 These output network variables are output when the operating mode has been changed They are also output when the status has been changed from an A C unit side with the remote controller They are output when the LonWorks Interface or the A C unit power is reset Contents 0 Auto heat cool 5 Dry 1 Heat 9 Fan 3 Cool i Pana_CZ CLNC1U_Engindd 12 3 12 2011 11 11 ao nv7 Option 1 setting command nv9 Option 2 setting command network input SNVT_switch nviOption1_00 network input SNVT_switch nviOption1_01 network input SNVT_switch nviOption1_02 network input SNVT_switch nviOption1_03 network input SNVT_switch nviOption2_00 network input SNVT_switch nviOption2_01 ne
19. ontents 0 Stop value 1 Start Not used nv2 Unit start stop status notification network output SNVT_switch nvoOnOff_00 network output SNVT_switch nvoOnOff_01 network output SNVT_switch nvoOnOff_02 network output SNVT_switch nvoOnOff_03 These output network variables are used to provide notification of the unit s current start stop status and the thermostat ON OFF status They are also output when the status has been changed from an A C unit side as with the remote controller They are output when the LonWorks Interface or the A C unit power is reset When the indoor units are subject to group control thermostat ON is output when 1 or more indoor unit is thermostats ON and thermostat OFF is output when all indoor unit are thermostats OFF state 0 Thermostat OFF 200 Thermostat ON Contents 0 Stop 1 Start value nv3 Temperature setting command network input SNVT_temp_p nviSetpoint_00 network input SNVT_temp_p nviSetpoint_01 network input SNVT_temp_p nviSetpoint_02 network input SNVT_temp_p nviSetpoint_03 These input network variables are used to change the indoor unit temperature setting If the temperature setting is only changed from an A C unit side as with the remote controller then it is not necessary to use these network variables When a temperature above the upper limit of the temperature which can be set by the indoor units has been speci
20. s are the same e Do not run the inter unit control lines the LonWorks communication lines and the power cables through the same conduit or place the cables near one another Doing so can cause the system to malfunction e Before turning the power on follow the instruction in Power Board Initial Settings e When using the spare inter unit cotrol line connect 1 and 8 at CN002 e When using the spare LON communication line connect 1 and 8 or 4 and 6 at CNOO3 S004 Indoor unit enabling SW Pana_CZ CLNC1U_Eng indd 5 5 2011 11 11 N Indoor Unit Enabling Switches Indoor unit group 3 is disabled Indoor unit group 3 is enabled Indoor unit group 2 is disabled Indoor unit group 2 is enabled Indoor unit group 1 is disabled Indoor unit group 1 is enabled Indoor unit group 0 is disabled Indoor unit group 0 is enabled e One main circuit board can control 4 groups indoor unit groups 0 3 e Set to disable if the indoor unit group does not exist Set to enable if the indoor unit group exists Setting Switches O ON OFF R C Remote Controller ana OFF R C prora Fan apaaa R C prohibit Air direction R C prohibit Filter sign Fan speed Air direction P Fan speed Filter sign Air direction Filter sign Not used Be sure to set to OFF OFF Central individual setting is according to the central control device normal setting ON Central individual se
21. the LonWorks Interface perform test runs of the A C units and assign central control addresses for A C units LonWorks Interface Test Run Procedure 1 Press and hold touch switch S001 on the main circuit board j a kl la bl sl for 5 seconds or longer Test run mode is enabled for the main circuit board that is currently being controlled LD001 illuminates and LD002 Jl s g LDOO8 turn off PUSH COM if esl Be bilbe 2 Press touch switch S002 The data LEDs appear as shown in the tables below In addition the assigned indoor unit groups start and stop I S002 PUSH as shown in the tables below 3 Be sure to reset the power after the LonWorks Interface test run is completed BE s leIlsI eI zI ls tart stop Start Stop Stop Stop Stop Stop Start Start SIGU Stop i Pana_CZ CLNC1U_Engindd 9 5 2011 11 11 mi 5 Checking the LonWorks Interface Version 1 Press touch switch S002 Version display mode is enabled on that circuit board for a period of 18 seconds LD001 illuminates and LD002 flashes at high speed COM 1 High speed flashing 2 While the version is displayed 18 seconds the display contents are the following Displays the first digit of the main microcomputer BaBa Data i Displays the second digit of the main i microcomp
22. tting is always set to individual OFF Control temperature is used for the room temperature normal setting ON _ Inlet temperature is used for the room temperature Not used Be sure to set to OFF Communicate as a sub central control device Communicate as a main central control device e If there are no central control devices other than this interface set to main ON e To set this interface as the main set only node 0 to main ON e If using in combination with an communication adapter AMY adapter intelligent controller or system controller set to sub OFF e If using in combination with an ON OFF controller set the ON OFF controller as the main if the ON OFF controller s remote controller prohibit function is to be used If this interface s remote controller prohibit function is to be used set this interface as the main Address Switches O ON OFF 4 Central control address ONOa PWN OO000 0000 O0O00 0000 OO00 0000 OO000 0000 oooojoooojooo0oo0ojoo0o0o0 0000 0000 0000 0 000 0 000 0000000 0 0000 i Pana_CZ CLNC1U_Engindd 6 5 2011 11 11 aoa Pana_CZ CLNC1U_Engindd 7 Communications LED Green COM Communications LD002 Display meaning X Power OFF Low High Flash writer writing in progress
23. twork input SNVT_switch nviOption2_02 network input SNVT_switch nviOption2_03 These input network variables are used to make the indoor unit option settings Two of the following 4 option settings can be selected remote controller prohibit fan speed setting air direction setting and filter sign reset Make changes using the DIP switches on the main circuit board When option settings are not made from the LonWorks it is not necessary to use these network variables Start stop Temp operation setting Operating mode Remote controller prohibit a O Permitted x Prohibited ac 100 pee Filter sign is reset when data is updated Not pet Fan speed setting fi oe Air direction Not Ep Fa setting sed Positions F4 and F5 can not be set for cool and dry mode operation Filter sign nv8 Option 1 setting status notification nv10 Option 2 setting status notification network output SNVT_switch nvoOption1_00 network output SNVT_switch nvoOption1_01 network output SNVT_switch nvoOption1_02 network output SNVT_switch nvoOption1_03 network output SNVT_switch nvoOption2_00 network output SNVT_switch nvoOption2_01 network output SNVT_switch nvoOption2_02 network output SNVT_switch nvoOption2_03 These output network variables provide notification of changes in the status of the indoor unit option settings Two of the following 4 option settings ca
24. uter i Next 3 seconds version l I I gaia ja Data First 3 seconds version i Displays the third digit of the main 5 microcomputer Next 3 seconds version Bigeye e Data Displays the first digit of the LonWorks I F microcomputer Next 3 seconds version ed EEE Displays the second digit of the LonWorks I F microcomputer Next 3 seconds version Baag E Data Last 3 seconds __ BIFIEIE e Version display JI sll6 5 BIE HHE LAHE BHn Bias a SEE 4 lt Example gt Main microcomputer LonWorks I F microcomputer 2 Baine Data lt JES JE E Data Bls aiie Data Bi Biais Data SIE SIM Data gaga ie Data i Pana_CZ CLNC1U_Engindd 10 5 3 HELE Version 3 56 Version 2 00 10 2011 11 11 veal 6 List of LonWorks Network Variables i Pana_CZ CLNC1U_Engindd 11 3 A C unit Input output Item Variable name Variable type Start stop nviOnOff_00 SNVT_switch Temp setting nviSetPoint_00 SNVT_temp_p Input Operating mode nviHeatCool_00 SNVT_hvac_mode Option 1 setting nviOption1_00 SNVT_switch Option 2 setting nviOption2_00 SNVT_switch Start stop status nvoOnOff_00 SNVT_switch Indoor group 0 Temp setting nvoSetPoint_00 SN
Download Pdf Manuals
Related Search