Panasonic BY-HPE11KTCE Operating Instructions
Contents
1. 3 Click Browse select the firmware file then click Open 4 Click Start 5 Click OK when prompted The firmware will be updated and then the adaptor will automatically restart After restarting the updated firmware is used IMPORTANT After you have finished using the maintenance screen restore the computer s IP address and network settings to their original values Do not disconnect the center adaptor from the power outlet until the update is completed After you have updated the firmware confirm the adaptor s firmware version on the Status screen See page 24 Update the firmware for both the camera adaptor and center adaptor Operating Instructions 23 3 Adaptor Maintenance Screen 3 2 2 Confirming the Adaptor s Status You can confirm the information in the table below such as the firmware version and MAC address of the adaptor on the Status screen 1 Access the maintenance screen of the adaptor 2 Click Status BY HPE11H_CE Option Update Firmware Restart Copyright IMPORTANT Status Display the status of this equipment Boot Version Firmware Version Operation Mode Teminal MAC Address of this equipment Another Master Not Detected Link Status Disconnected MAC Address of Master Unregistered PoE Ethemet Link Unknown PoE PoE Switch Unknown PoE PoE Power Supply Unknown Renew The screen shown here depicts the screen shown when access2. screen is set to Link down Confirm that the camera adaptor network camera and other network devices are connected properly that there are no connection problems such as damage or breaks in the cables and that network devices are connected to the power outlet see 3 2 Connections in the Installation Guide The status of the PoE PoE Switch on the maintenance screen is set to OFF Turn the PoE switch on the camera adaptor to ON see page 10 Power cannot be supplied normally from the center adaptor to the camera adaptor The PoE function cannot supply power to devices connected with coaxial cable at distances over 500 m see 3 2 Connections in the Installation Guide The PoE function may not be able to supply power if the line resistance of the coaxial cable is of a high value see 3 2 Connections in the Installation Guide 4 4 Other Issues Problem Cause and Remedy The unit is warm This is normal The unit may seem slightly warmer in summer than compared to winter Ifthe unit gets extremely hot disconnect the power plug and contact an authorized service center Operating Instructions 31 5 Specifications 5 Specifications Center Adaptor BY HPE11H Items Specifications Operating Environment Temperature 0 C to 50 C Humidity 20 85 no condensation Interfaces 10Base T 100Base TX x 1 AUTO MDI MDI X AC inlet BNC connec
3. 3 Adaptor Maintenance Screen 3 Adaptor Maintenance Screen 16 The adaptor s maintenance screen can be displayed on the web browser of a PC connected to the network connector of an adaptor Settings such as the following can be performed in the maintenance screen firmware version updates adaptor status confirmation IP address and password changes IMPORTANT To display the maintenance screen of adaptors that have already been installed or connected directly connect the camera or center adaptor to a PC with a LAN cable In order to access the adaptor s maintenance screen you must temporarily change the IP address assigned to your computer Before you change the IP address of your computer note the IP address and network settings already assigned to your computer After you have finished using the maintenance screen restore the computer s IP address and network settings to their original values If you plan to update the adaptor s firmware download the latest version of the adaptor s firmware from the Panasonic support site http panasonic net pss security products coax index html and save it on the computer before you change the IP address of the computer Operating Instructions 3 Adaptor Maintenance Screen 3 1 Accessing the Maintenance Screen 3 1 1 Temporarily Changing the Computer s IP Address Temporarily change the IP address assigned to your computer to access the adaptor s mainten
4. Straight cable automatic recognition Transmission Rate 10 Mbps 100 Mbps Auto Sensing Number of Ports 1 RJ 45 connector Protocol TCP IP UDP Access Method CSMA CD Items Specifications Number of adaptors that can be communicated with 1 camera adaptor can be connected via coaxial cable for each center adaptor Connectable Devices Center adaptor devices equipped with 10Base T 100Base TX interfaces Camera adaptor Panasonic network cameras see http panasonic net pss security products coax index html for more information Number of devices that can be connected A maximum of 256 center adaptors or camera adaptors can be connected in 1 segment intenance Screen Specifications Items Specifications Compatible Operating Systems Windows XP Windows Vista Windows 7 Web Browser Internet Explorer 6 0 7 0 8 0 or later Operating Instructions 33 5 Specifications Performance Specifications Items Specifications Transmission Speed UDP 45 Mbps or higher when using an RG 6 U coaxial cable at distances under 2 km Transmission Speed TCP 35 Mbps or higher when using an RG 6 U coaxial cable at distances under 2 km Maximum Transmission Distance Without PoE function 2 km With PoE function 500 m when using a Panasonic network camera 300 m when using a ClassO standa
5. be changed e The screen shown here depicts the screen shown when accessing a camera adaptor The screen displayed for the center adaptor and camera adaptor is different Operating Instructions 27 3 Adaptor Maintenance Screen Viewing the center adaptor s MAC address only from the camera adaptor You can access the camera adaptor s maintenance screen and view the MAC address of the center adaptor 1 Access the maintenance screen of the camera adaptor 2 Click Option then click the Terminal List Delete tab BY HPE1IR_CE Option Status IP Address Account Terminal List Delete Update Firmware Porn The list of terminals that are registered in this equipment Select the terminals and then click delete button to deregister the selected terminals Copyright This equipment will restart to reflect the settings with the click delete button To re register the terminal you need to initialize the terminal first For the details please refer to the manuals The center adaptors MAC address is displayed The Delete button Cancel button and check box cannot be used IMPORTANT After you have finished using the maintenance screen restore the computer s IP address and network settings to their original values The MAC address of the center adaptor is written on the underside of the center adaptor 28 Operating Instructions 4 Troubleshooting 4 Troubleshooting Before sending the unit in fo
6. coaxial cables insert objects into the conductor or connect coaxial cables with incomplete relays If water or other objects enter the conductor or coaxial cables with incomplete relays are connected it may result in electric shock or fire Disconnect the AC cord and contact an authorized service center if there is any damage to the coaxial cables Do not damage existing wires or pipes when making holes for mounting or wiring e This may result in earth leakage electric shock or fire Do not install or use the unit near medical equipment e High frequency signals emitted from the unit may affect the operation of medical equipment and cause malfunctions Do not expose the unit to rain or any type of moisture To prevent the risk of fire or electrical shock do not place objects such as cups or vases near the unit If the unit is exposed to moisture disconnect the AC cord and contact an authorized service center Do not touch the core of the coaxial cable Amaximum of DC 60 V is applied to the coaxial cable This may result in electric shock Do not perform wiring or installation during thunderstorms e This may result in electric shock or fire Secure screws with the specified torque e Serious damage and or injury may result if the unit falls CAUTION Disconnect the AC cord of the center adaptor if the unit will not be used for long periods of time or when performing care and cleaning e Leaving the AC cord connected when
7. connecting wiring or touching the AC cord power plug LAN cable or coaxial cable during an electrical storm Do not use the unit in the vicinity of a gas leak Use only the AC cord indicated in this manual SAVE THESE INSTRUCTIONS Operating Instructions 7 General Precautions General Precautions Follow the instructions written in For Your Safety see page 3 and Important Safety Instructions see page 7 together with the instructions written below 1 The unit is intended for indoor use only and should not be mounted outdoors 2 The unit uses the same high frequency signals as used by the radio signals of amateur radio shortwave broadcasting aviation radio and marine radio Therefore operational interference may occur if the unit is used in proximity to devices that transmit these radio signals 3 Do not connect the camera adaptor BY HPE11R to communications carrier equipment such as rental modems 4 Follow the following precautions in order to maintain product performance over long periods of time Do not use the unit in areas with high temperatures or humidity for long periods of time Use in these areas can degrade parts which can shorten the life span of the unit We recommend areas that have temperatures of 35 C or lower Do not install the unit in places that can be directly exposed to heat sources 5 Proper handling of the unit Do not drop or expose the unit to strong vibrations or shaking This may
8. is connected to the center adaptor Orange lit The camera adaptor is activating LINK Red lit The camera adaptor is malfunctioning Contact an authorized service center Off The center adaptor is not connected to the power outlet or the coaxial cable is not connected Center adaptor Indicator Light Status Meaning Green lit The center adaptor is active Green flashing The center adaptor may be connected to a device other than the camera adaptor with the coaxial POWER cable Check the connection with the camera adaptor Off The center adaptor is not connected to the power outlet Green lit A network device is connected Green flashing Sending receiving data from a network device Orange lit A network device is not connected or the LAN connected network device is not connected to the power outlet Off The center adaptor is not connected to the power outlet Green lit The camera adaptor is connected to the center adaptor Red lit The center adaptor is malfunctioning Contact an COAXIAL authorized service center Off The center adaptor is not receiving power or the coaxial cable or camera adaptor is not connected Operating Instructions 13 2 Resetting the Unit 2 Resetting the Unit Reset the unit when reselling disposing or sending it for repairs 2 1 Resetting Camera Adaptors Reset the camera adaptor when it is con
9. other countries All other trademarks identified herein are the property of their respective owners Operating Instructions For Your Safety For Your Safety To prevent severe injury and loss of life property read this section carefully before using the unit to ensure proper and safe operation of your unit WARNING Consult an authorized dealer for mounting Experience and knowledge are required to perform mounting of the unit Incorrect mounting can cause damage to the unit fire electric shock or injury Make sure to consult an authorized dealer for mounting Do not damage the AC cord or power plug Do not allow the AC cord or plug to be damaged placed near heat emitting devices excessively pulled bent or placed under heavy objects Using damaged AC cords or plugs can result in the risk of fire or electric shock Contact an authorized service center for AC cord and plug repairs Do not use the unit if it does not work normally Unplug the unit from the power outlet if it emits smoke an abnormal smell or makes unusual noise Consult an authorized service center for repairs Do not disassemble or repair the unit To reduce the risk of electric shock or fire do not disassemble the unit Contact an authorized service center when service is required Use only the power source specified for the unit e Overloading the unit by having many loads on one electrical outlet etc may cause excessive heat resulting in fire Co
10. the adaptor s IP add ress and subnet mask if necessary Change the IP address in cases such as when the adaptor is using the same IP address as another network device or if you want to match the address used in the network 1 Access the maintenance screen of the adaptor 2 Click Option BY HPE11R_CE Update Firmware Restart You can change the IP address of this equipment Copyright IP Address 192 168 249 249 Subnet Mask 255 255 255 0 Enter the desired IP address Enter the subnet mask if necessar a i a Click Restart Option Account Terminal List Delete Click Set button and then restart this equipment to reflect the settings Set Cancel y Click Set then click OK when prompted The adaptor will restart and the new settings will take effect The new IP address must be entered in the web browser s address bar in order to access the adaptor s maintenance screen IMPORTANT After you have finished using th again e maintenance screen restore the computer s IP address and network settings to their original values adaptor The screen displayed different 26 Operating Instructions Match the IP address and subnet mask settings to those used in your network The screen shown here depicts the screen shown when accessing a camera for the center adaptor and camera adaptor is 3 Adaptor Maintenance Screen Changing the adaptor s password You may chan
11. the unit is not used for long periods of time or when performing care and cleaning may result in earth leakage electric shock or injury Operating Instructions 5 For Your Safety Do not mount the unit to ceilings or walls made of soft materials Do not mount the unit to soft ceilings or walls such as plasterboard ALC aerated light weight concrete concrete blocks or any surfaces under 25 mm thickness Injury may result if the unit falls Do not pull cables or apply excessive force to connectors e This may damage the cables or connectors and result in electric shock Do not connect other devices to the BNC connector of the unit This may damage the unit Do not expose the unit to fire or naked flames e This may result in fire The AC cord is used as the main disconnect device e Ensure that the power outlet is installed near the unit and is easily accessible Do not play the included CD ROM in an audio CD player Ear splitting volume may hurt your ears and damage the CD player s speakers 6 Operating Instructions Important Safety Instructions Important Safety Instructions When using this unit basic safety precautions should always be followed to reduce the risk of fire electric shock or personal injury 1 2 3 4 Do not use this unit near water for example near a bathtub washbow l kitchen sink or laundry tub in a wet basement or near a swimming pool Avoid handling or installing the unit
12. 8 249 and Subnet mask 255 255 255 0 For the IP address 1 254 However 249 cannot be used r Internet Protocol Version 4 TCP IPv4 Properties L2 m l General for the appropriate IP settings Obtain an IP address automatically Use the following IP address Default gateway Obtain DNS server ad cally Use the following DNS server addresses Preferred DNS server Alternate DNS server __ Validate settings upon exit You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator IP address Subnet mask Advanced L A 6 Click Close to exit the Local Area Connection Properties screen IMPORTANT The procedure for changing the IP address may change depending on whether the viewing method for Windows 7 is set to Large icons or Small icons Refer to the help file supplied with the operating system for more information 18 Operating Instructions 3 Adaptor Maintenance Screen 3 1 2 Accessing the Maintenance Screen Follow the procedure below after you have changed the IP address of the computer 1 Connect the adaptor camera adaptor or center adaptor and computer using a LAN cable When accessing the camera adaptor make sure it is connected to the center adaptor with a coaxial cable and that the center adaptor is connected to the power o
13. CE Operating Instructions 35 Panasonic Marketing Europe GmbH Hagenauer Strasse 43 65203 Wiesbaden Germany For information of Compliance with EU relevant Regulatory Directives Contact to Authorised Representative For EU only Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Panasonic System Networks Co Ltd 2010 PNQX3365ZA KK1210CMO
14. Panasonic Operating Instructions Coaxial LAN Converter with PoE function Indoor Use Only modetNo BY HPE11KTCE BY HPE11H Attached Installation Guide Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use Introduction Introduction About the user manuals There are 2 sets of operating instructions for this unit as follows Installation Guide Explains how to install and connect devices Operating Instructions PDF Explains how to perform the settings and how to operate this unit Adobe Reader is required to read these operating instructions PDF on the provided CD ROM When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it The BY HPE11R adaptor is called the camera adaptor and the BY HPE11H adaptor is called the center adaptor in this document Trademarks Microsoft Windows Windows Vista and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Microsoft product screen shot s reprinted with permission from Microsoft Corporation Linux is a registered trademark of Linus Torvalds in the United States other countries or both Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or
15. Problem Cause and Remedy When testing the communication speed all the indicators are off or only 1 or 2 of the indicators are lit The communications speed may be affected due to issues with the installation environment This is not a malfunction Confirm that there are no problems with using the camera or displaying images Confirm that the coaxial cable is of a suitable type and length and that there are no devices near the unit that may cause strong interference Operating Instructions 4 3 PoE Issues 4 Troubleshooting Problem Cause and Remedy Network cameras connected to the camera adaptor do not function The connection distance may be too long The PoE function cannot supply power to devices connected at distances over 500 m Confirm that the connected LAN cable is a PoE standard cable see 3 1 Connection Example in the Installation Guide that the LAN cable is connected properly and that there are no connection problems such as damage or breaks in the cable If the LAN cable was quickly disconnected and then reconnected the PoE function may not be able to supply power Disconnect the LAN cable and then reconnect after waiting for more than 2 seconds The status of the PoE PoE Power Supply on the maintenance screen is set to Disable and the PoE function cannot supply power The status of the PoE Ethernet Link on the maintenance
16. ance screen The procedure for changing the IP address differs depending on the operating system used Windows 7 Changing your computer s IP address In Microsoft Windows 7 this procedure must be performed by either the Administrator user or a user assigned with administrator level privileges Refer to the help file supplied with the operating system for more information 1 Click Start gt Control Panel View network status and tasks 2 Click View your active networks Local Area Connection 3 Click Properties under Local Area Connection Status 4 Select Internet Protocol Version 4 TCP IPv4 then click Properties Local Area Connection Properties lema Networking Connect using a NVIDIA nForce Networking Controller This connection uses the following items 1 Client for Microsoft Networks cos Packet Scheduler rie and Printer Sharing for Microsoft Networks 4 Intemet Protocol Version 6 TCP IPv6 4 Link Layer Topology Discovery Mapper 1 0 Driver 4 Link Layer Topology Discovery Responder Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks KI KI KI KI KI KI KI OK Cancel Operating Instructions 17 3 Adaptor Maintenance Screen 5 Select Use the following IP address then click OK after entering the IP address 192 16
17. authorized service center if any foreign objects or liquids enter the unit Regularly check the unit e Rusted brackets or screws may cause the unit to fall causing serious damage and or injury Consult an authorized dealer for checks Mount the unit to secure locations that can support the weight of the unit e Serious damage and or injury may result if the unit falls Reinforce the mounting area if it has insufficient strength to secure the unit Make sure to use the safety wire Attach the safety wire in a position so that if the camera adaptor were to become detached it would not fall on nearby people Do not use the unit where it can be exposed to flammable or explosive gasses This may cause the unit to explode resulting in injury Do not mount the unit where it can be exposed to vibrations e This may cause the unit to fall resulting in injury Do not use the unit where it can be exposed to corrosive gas or salty conditions This may cause the unit parts to degrade and the unit may fall resulting in damage and or injury Do not drop or expose the unit to strong shaking This may result in electric shock or fire 4 Operating Instructions For Your Safety Turn the power off before performing wiring e This may result in electric shock or result in fire from wiring shorts or incorrect wiring Only use mounting brackets made for the unit e Serious damage and or injury may result if the unit falls Do not damage
18. cause malfunctions 6 Take precautions for when reselling disposing or sending the unit for repairs e Take adequate precautions when handing the unit over to third parties 7 Care and cleaning for the unit e Perform cleaning and care after disconnecting the center adaptor from the power outlet Do not use benzine thinner or any other abrasive powders when cleaning This may change the color of the unit cases 8 Cleaning stains from the unit e Wipe stained areas with a damp soft cloth For FRG Users For Germany Only e Machine noise information regulation 3 GPSGV the maximum sound pressure level is 70 dB A or less in conformity with EN ISO 7779 e This device is not intended for use in the direct field of view at visual display workplaces To avoid incommoding reflexions at visual display workplaces this device must not be placed in the direct field of view 8 Operating Instructions Table of Contents Table of Contents 1 Main UII i s li s zil iisikninn na mianknki zina zinrakan naasanakanana anal n kana ka ka a la a naa ua n RE 10 1 1 Camera Adaptor BY HPE11R A iEi kk kake kk kk kake kk kk k KAKA KK KA KAR 10 1 2 Center Adaptor BY HPE 11H J J kk kake kk kaka kek EK kK KAKA KAK KA KAW 12 1 3 Understanding the Indicators E ik ka kk kaka aka kk kk ennn 13 2 Resetting the Unit 3 i xxii yini iaaiiai 14 2 1 Resetting Camera Adaptors 2 cccccsecesee
19. e 3 2 Connections in the Installation Guide The network device connected to the network connector may not be receiving power Connect the network device to a power outlet see 3 2 Connections in the Installation Guide A network device is not connected to the network connector with a LAN cable Confirm that the LAN cable is connected properly see 3 2 Connections in the Installation Guide and that there are no connection problems such as damage or breaks in the cable Operating Instructions 29 4 Troubleshooting Problem Cause and Remedy The center adaptor s COAXIAL indicator is not lit The center adaptor is not receiving power Confirm that the AC cord is connected to the power outlet and AC IN of the center adaptor see 3 2 Connections in the Installation Guide The coaxial cable is not connected Confirm that the coaxial is not over 2 km in length and is connected properly see 3 2 Connections in the Installation Guide Confirm that there are no connection problems such as damage or breaks in the cable The camera adaptor is not connected Connect the center and camera adaptors with a coaxial cable see 3 2 Connections in the Installation Guide The center adaptor s COAXIAL indicator is lit red Data cannot be sent because the center adaptor may be malfunctioning Contact an authorized service center 4 2 Communication Speed Issues 30
20. e Camera Adaptor in the Installation Guide Used when attaching the camera adaptor to screws inserted into a wall Operating Instructions 11 1 Main Unit 1 2 Center Adaptor BY HPE11H Front view Panasonic LAN SPEED INITIAL POWER LAN COAXIAL SET 10BASE T 1 gt lt gt lt gt OOBASE TX wo Center Adaptor BY HPE11H Indicators Displays the status of the center adaptor see page 13 SPEED button Used when measuring the speed between adaptors see 3 2 Connections in the Installation Guide INITIAL SET button Used to reset the center adaptor to its factory default settings see page 15 Network connector Connects the center adaptor to a network device with a LAN cable see 3 2 Connections in the Installation Guide Rear view BNC connector Connects the center adaptor to the camera adaptor with a coaxial cable see 3 2 Connections in the Installation Guide AC IN Connects the center adaptor to the power outlet with the included AC cord see 3 2 Connections in the Installation Guide 12 Operating Instructions 1 Main Unit 1 3 Understanding the Indicators The light indicators change depending on the operating status of the camera and center adaptors Camera adaptor Indicator Light Status Meaning Green lit The camera adaptor
21. ecting it to another adaptor and accessing its maintenance screen You may reset the computer s ARP table if you do not want to restart the computer Refer to the help file or operating instructions supplied with the operating system for more information Resetting the ARP table when using Windows 7 1 Display the command prompt by clicking Start J All Programs gt Accessories Command Prompt 2 Enter arp d then press Enter Operating Instructions 21 3 Adaptor Maintenance Screen 3 1 4 System Requirements Operating System Web Browser Microsoft Windows 7 Internet Explorer version 8 0 or later Microsoft Windows Vista Internet Explorer version 7 0 or later Microsoft Windows XP Internet Explorer version 6 0 or later 22 Operating Instructions 3 Adaptor Maintenance Screen 3 2 Using the Maintenance Screen 3 2 1 Updating the Adaptor s Firmware Make sure you download the latest version of the adaptor s firmware from the Panasonic support site http panasonic net pss security products coax index html and save it to the computer before changing the computer s IP address and accessing the maintenance screen 1 Access the maintenance screen of the adaptor 2 Click Update Firmware BY HPE1H CE Update Firmware Seine You can upgrade the firmware version Option Curent Version Wl Restart File Name Browse Copyright Start Cancel
22. eeeeeeeeeeeeeeneeceeeeeseeeeneeeeeeeeeeeeaes 14 2 2 Resetting Center Adaptors cceccsseeesceneeeseeeeeeseeeeeseneeseseenseseeeeeensneeenees 15 3 Adaptor Maintenance Screen cccceseesseeeeeeeeeeeeseeneeeeeeseeeneneeeeeees 16 3 1 Accessing the Maintenance Screen ccccssscecssseneeeeseeeeeneesneeeeeseeneeeeeseeees 17 3 1 1 Temporarily Changing the Computer s IP Address cccccceceeeeeeeeteeeees 17 3 1 2 Accessing the Maintenance Screen kek k 19 3 1 3 Maintenance Screen Overview iiii Ek kek kek kk kk 21 3 14 System REQUINEIMEINS cvs s ar sisl r n k n kn dy na yaya lan db dan kaba ke k da kanan ne ya ka b n yan b kaka 22 3 2 Using the Maintenance Screen AJ kk kk kaka kk k AK KK KAWAR KAR 23 3 2 1 Updating the Adaptor s Firmware iiiEE kk kk kk kk kk k 23 3 2 2 Confirming the Adaptor s Status 0 0 ieee kk ek kk k kK 24 3 2 3 Changing Adaptor Settings ii Ek kk kk kk ek k kK 26 4 Tro bl shootil j i i iki dx kk k Za kak kaka ala kak ek akai ka kek kak HAR Ra k Kh kaka a 29 4 1 Indicator Display Issues 0 0 cccceeeeeneeeeeeee kk kak kaka kaka k K KAKE AKA WEKA KWA HAAA WAKE 29 4 2 Communication Speed ISSUES eceseeeeee cece kk kaka ek kk KAK KAKA AK KAKA KAK KAR 30 4 3 _DakD gt gt gt gt gt gt gt _ o o e ej e 31 4 4 Other ISSUCS i i sna nd uraani darika kake diu ek la
23. ge the adaptor s password if necessary The password is required to access the maintenance screen 1 Access the maintenance screen of the adaptor 2 Click Option then click the Account tab BY HPE11R_CE Option z D2 Update Finnware Restart You can change your password User name cannot be changed Compas Password should be 6 to 12 characters Sr Note Space amp lt or gt are not allowed Username BY HPE11 Password Password Retype Set Cancel 3 Enter the desired password within 6 12 characters only A Z a z and 0 9 can be used e Passwords are case sensitive e Space amp lt and gt cannot be entered 4 Click Set then click OK when prompted 5 Click Restart The adaptor will restart and the new settings will take effect The new password must be entered in order to access the adaptor s maintenance screen again IMPORTANT After you have finished using the maintenance screen restore the computer s IP address and network settings to their original values e To increase security we recommend changing the adaptor s password Do not forget the password If the password is forgotten you can reset the password to the default value 999999 by resetting the adaptor see page 14 If the adaptor is reset all registration information is erased Do not disclose the password you are responsible for managing your password The user name cannot
24. ing a center adaptor The screen displayed for the center adaptor and camera adaptor is different Link Status and MAC Address of Master are not displayed on the camera adaptor s screen Items Description Boot Version Displays the adaptor s boot version Firmware Version Displays the adaptor s firmware version Operation Mode Displays the adaptor type camera adaptor or center adaptor Camera adaptors are displayed as Master and center adaptors are displayed as Terminal MAC Address of this Displays the MAC address of the connected adaptor equipment Another Master Indicates whether other camera adaptors exist on the network If other camera adaptors exist on the network Detected is displayed if they do not exist Not Detected is displayed Communication performance may be affected if other camera adaptors are detected Link Status only Displays the status of the connection between the center and displayed for the camera adaptor Connected is displayed when there is a center adaptor connection and Disconnected is displayed when there is no connection 24 Operating Instructions 3 Adaptor Maintenance Screen Items Description MAC Address of Master only displayed for the center adaptor Displays the MAC address of the connected camera adaptor If no camera adaptor is connected Unregistered is displayed PoE Ethernet Link Displays
25. mpletely insert the power plug into the power outlet e Failure to do so may cause electric shock and or excessive heat resulting in a fire Do not use damaged power plugs or power outlets Regularly remove any dust etc from the power plug e Regularly remove any dust etc from the power plug by pulling it from the power outlet then wiping with a dry cloth Accumulated dust may cause an insulation defect from moisture etc resulting in a fire Do not bring metal objects near the power outlet slots e This may result in electric shock or fire Do not hold the power plug by the metal parts e This may result in electric shock or fire Never touch the power plug with wet hands e This may result in electric shock Operating Instructions 3 For Your Safety Do not touch the unit LAN cable coaxial cable AC cord or power plug during thunderstorms e This may result in electric shock Do not use the included AC cord with other devices e This may result in electric shock or fire Only use the included AC cord Using other AC cords may result in electric shock or fire Place the unit securely on a stable level surface e Serious damage and or injury may result if the unit falls Do not install the unit in a dusty or moist place This may result in electric shock or fire Never push any objects into the unit or spill any liquids on the unit e This may result in electric shock or fire Disconnect the AC cord and contact an
26. na l dk w ka kula d dk ea y Va uk k a kak wak HE KAW AZ 31 5 Specificati S ilii nalin misri aki saraya baka n n a aa n na a a an a RES SWE A baka HN kwa w Ra GL RRA 32 Operating Instructions 9 1 Main Unit 1 Main Unit 1 1 Camera Adaptor BY HPE11R Front view 10 Indicator Displays the status of the camera adaptor see page 13 PoE switch Turns the PoE function ON OFF The default setting is ON IMPORTANT When using the camera adaptor s PoE function to supply power to a network camera set the PoE switch to ON When not using the PoE function when powering the network camera with an AC adaptor set it to OFF e The PoE function cannot be used for connections over 500 m Set the PoE switch to OFF BNC connector Connects the camera adaptor to the center adaptor with a coaxial cable see 3 2 Connections in the Installation Guide Network connector Connects the camera adaptor to a network camera with a LAN cable see 3 2 Connections in the Installation Guide INITIAL SET button Used to reset the camera adaptor to its factory default settings see page 14 Operating Instructions 1 Main Unit Rear view Used when attaching the camera adaptor to a ceiling or wall with screws see 2 1 Mounting the Camera Adaptor in the Installation Guide Used when attaching the safety wire see 2 1 Mounting th
27. nected to the center adaptor with a coaxial cable and the center adaptor is connected to the power outlet 1 Press the camera adaptor s INITIAL SET button for about 3 seconds with a pointed object e The indicator will start flashing green 2 The camera adaptor s indicator is lit green e Resetting is completed when the indicator is lit green after changing from flashing green to flashing orange However depending on the condition of the connection the indicator may be lit green after alternating from flashing orange to lit orange IMPORTANT Do not disconnect the center adaptor s AC cord or the coaxial cable during resetting or within 30 seconds after resetting because the internal information may not have completed resetting 14 Operating Instructions 2 Resetting the Unit 2 2 Resetting Center Adaptors 1 Press the center adaptor s INITIAL SET button for about 3 seconds with a pointed object All the indicators will start flashing green Im Z e y emend kemere 2 All of the center adaptor s indicators are lit green e Resetting is completed when all the indicators are lit green after changing from flashing green IMPORTANT Do not disconnect the center adaptor s AC cord within 30 seconds after resetting because the internal information may not have completed resetting Operating Instructions 15
28. r repairs check if the problem can be resolved by following the troubleshooting steps If the problem cannot be solved by the steps in the troubleshooting contact an authorized service center 4 1 Indicator Display Issues Problem Cause and Remedy All the indicators are not lit The center adaptor may not be receiving power Confirm that the AC cord is connected to the power outlet and the AC IN of the center adaptor see 3 2 Connections in the Installation Guide Only the camera adaptor s indicator is not lit The coaxial cable is not connected Connect the coaxial cable Confirm that the coaxial cable is not over 2 km in length and is connected properly see 3 2 Connections in the Installation Guide Confirm that there are no connection problems such as damage or breaks in the cable The camera adaptor s LINK indicator is lit red Data cannot be sent because the camera adaptor may be malfunctioning Contact an authorized service center The center adaptor s POWER indicator is flashing green The center adaptor may be connected to a device other than the camera adaptor Check the connection with the camera adaptor see 3 2 Connections in the Installation Guide The center adaptor s LAN indicator is lit orange A network device is not connected to the network connector Connect a network device to the network connector with a LAN cable se
29. rd network camera This value is for transmissions between the BY HPE11H and BY HPE11R The transmission speed when using an RG 6 U coaxial cable may very depending on factors such as the coaxial cable condition and network environment The values shown here measured in environments not affected by cable or network environment conditions Measured using Linux FTP Maximum Transmission Distance PoE Power Supply when using RG 6 U coaxial cable Specifications 34 Maximum Transmission Distance 300 m 500 m 1 000 m 1 500 m 2 000 m Power Supplied by PoE 15 4 W 12 0 W Cannot supply power with PoE When connecting an IEEE802 3af Alternative B classO network camera to the camera adaptor BY HPE11R When connecting a Panasonic network camera see http panasonic net pss security products coax index html for more information to the camera adaptor BY HPE11R Turn the PoE switch OFF in this situation Operating Instructions 5 Specifications RG 6 U coaxial cable In this document coaxial cables with the following specifications are referred to as RG 6 U coaxial cables Coaxial Cable Type DC R 300 m of Inner Conductor Maximum Cable Length for PoE connections Maximum Cable Length for non PoE connections RG 6 U Less than 12 Q 500 m 2 000 m Accessories Rack Mount Connecting Fitting BY HCA10
30. s and network settings to their original values Only a PC connected to the adaptor s network connector can display the maintenance screen and perform firmware updates etc The maintenance screen is displayed in English 20 Operating Instructions 3 Adaptor Maintenance Screen 3 1 3 Maintenance Screen Overview BY HPE11H_CE Status Display the status of this equipment a Se ae ae eae nn i Update Firmware 1 Boot Version e i reee 1 Firmware Version i 1 Operation Mode Terminal 1 Copyright MAC Address of this equipment omer f Another Master Not Detected 1 Link Status Disconnected 1 MAC Address of Master Unregistered 1 1 I PoE Ethemet Link Unknown POE PoE Switch Unknown I 1 ROE PoE Power Supply Unknown I Model name Name of current screen Click to jump to the corresponding page Click to restart the adaptor Click to view the copyright information Contents of the current screen Click to update the displayed information IMPORTANT The screen shown here depicts the screen shown when accessing a center adaptor The screen displayed for the center adaptor and camera adaptor is different When consecutively connecting adaptors to the computer to access their maintenance screens because the information ARP table of the previously connected adaptor is retained the maintenance screen may not be able to be opened Therefore we recommend restarting the computer before conn
31. the status of the connection between the camera adaptor and network device Link up is displayed if there is a connection and Link down is displayed if there is no connection When viewing the center adaptor s maintenance screen information from the camera adaptor is obtained and displayed If the information cannot be obtained Unknown is displayed PoE PoE Switch Displays the status of the camera adaptor s PoE switch ON OFF When viewing the center adaptor s maintenance screen information from the camera adaptor is obtained and displayed If the information cannot be obtained Unknown is displayed PoE PoE Power Supply Displays whether the camera adaptor s PoE function is able to supply power to connected devices or not Enable is displayed if the camera adaptor is able to supply power and Disable is displayed if it is not When viewing the center adaptor s maintenance screen information from the camera adaptor is obtained and displayed If the information cannot be obtained Unknown is displayed IMPORTANT After you have finished using the maintenance screen restore the computer s IP address and network settings to their original values Operating Instructions 25 3 Adaptor Maintenance Screen 3 2 3 Changing Adaptor Settings The IP address and password for accessing the maintenance screen can be changed Changing the adaptor s IP address You may change
32. tor Dimensions WxHxD About 105 mm x 44 mm x 210 mm main body only Mass Weight About 570 g Power Supply AC 100 240 V 50 60 Hz 0 6 A Power Consumption Maximum about 28 W including the power consumption of the camera adaptor Coaxial Cable Power Supply Capability Maximum 22 W Camera Adaptor BY HPE11R Items Specifications Operating Environment Temperature 10 C to 50 C Humidity 20 90 no condensation Interfaces 10Base T 100Base TX x 1 AUTO MDI MDI X PoE compatible BNC connector Dimensions WxHxD About 80 mm x 115 mm x 35 mm main unit only Mass Weight About 165 g Power Supply Original power system DC 55 V from the center adaptor via the coaxial cable Power Consumption Included in the center adaptor s power consumption PoE Power Supply Capability Maximum 15 4 W see page 34 for more information Coaxial Interface Items Specifications Standard Panasonic original system 32 Operating Instructions 5 Specifications Items Specifications Frequency Range 2 MHz 28 MHz Data Transfer Mode Wavelet OFDM Access Method CSMA CA Error Correction Reed Solomon Code Convolutional Code Viterbi decoding LAN Interface Connection Specifications Ma Items Specifications Standard IEEE802 3 IEEE802 3u 10Base T 100Base TX MDI MDI X Cross
33. utlet 2 IMPORTANT To display the maintenance screen of adaptors that have already been installed or connected directly connect each adaptor to a PC with a LAN cable 2 Start the computer s web browser See page 22 for information on web browsers 3 Enterhttp 192 168 249 249 in the web browser s address bar 4 Enter the user name and password Default user name BY HPE11 Default password 999999 e The screen shown here depicts the screen shown when using Windows 7 Windows Security Xa The server 192 168 249 249 at BY HPE11H_CE requires a username and password _ BY HPEI1 E Er i Remember my credentials OK Cancel Operating Instructions 19 3 Adaptor Maintenance Screen 5 Click OK The maintenance screen is displayed BY HPE11H_CE Status Stats Display the status of this equipment Option Update Firmware Boot Version gt Restart Firmware Version l Operation Mode Terminal Copyright MAC Address of this equipment Another Master Not Detected Link Status Disconnected MAC Address of Master Unregistered PoE Ethemet Link Unknown PoE PoE Switch Unknown PoE PoE Power Supply Unknown Renew The screen shown here depicts the screen shown when accessing a center adaptor The screen displayed for the center adaptor and camera adaptor is different After you have finished using the maintenance screen restore the computer s IP addres
Download Pdf Manuals
Related Search