Panasonic Arbitrator 360 User Guide
Contents
1. Green LED 4V 4 2V Note Place TX on the charger at least 4 5sec for the initializing Installation for Charger stand gt lt Bottom gt Charger Stand To prevent units from being broken by the improper use Microphone Jack 8 Mute Button detach TX unit from RX unit as the drawing described on the right picture FCC Label 9 Talk Button Serial Number Label Mode Selection Button CAUTION Use only provided antenna with RX Set Do not immerse in water or keep in humid areas Do not place near TV speakers or other electronic devices Before installation check power supply and voltage to avoid hazards Do not apply force or shock to the unit Do not disassemble the unit Placement of items on the duty belt can restrict ready access to important equipment The location of the wireless transmitter or any other device provided with this system that is carried on the officer s person should be chosen with care and consideration After a location is selected the officer should test access to and practice drawing primary items such as service firearms and secondary defense devices such as Aerosol Subject Restraint Batons Electronic Disruption Devices etc Proper operation of handheld radios and other signaling devices should also be tested as should access to handcuffs and other restraining devices Do not ware body worn cords in such a way that can cause strangulation i e loop around the neck2. battery pack the unit has to be fully discharged by using approximately every 6 months Then recharge the battery to full capacity again DESCRIPION Main Cable To Receiver Power Red Power GND Black Audio Out j RCA connector eo ay Sauna E Trigger REC j Yellow ae DEG Z GND Black Connection with the system Power DC12V Red Power GND Black Power Cables to engine battery Audio Out RCA Connector Connects to AUDIO IN 1 port in the back of recorder Trigger REC Yellow Connect to GPIO1 brown cable GND Black Connect to GPIO black cable DESCRIPION Receiver lt Bottom gt Antenna Connection Serial Number Label Talk On Green LED EJ Main Cable Connection BATT Battery Status 7 FCC Label 2 Talk On LED 3 Charging Status When TX triggers the recording of the Red LED In charging system green LED lights on Green LED Fully Charged 4 OPERATION Install the bracket by using the screws Slide RX Set onto the Bracket Connect the main cable to RX Set Connect the antenna Internal Antenna or External Antenna to the RX Set Place external antenna on the windshield at the point Horizontal or Vertical as following picture lt External Antenna Installation gt Put the battery pack into TX Set Switch the power ON located on the bottom of TX unit Prior to use charge the unit by placing TX set
3. in the RX set at least for 3 hours Place TX on RX to sync the code OPERATION 1 Charging mode While TX is placed in RX No LED on charging the battery 2 TALK mode While TX is displaced from Rx TX TALK button will be standard mode on automatically in 3 seconds LED blinking 2 times and then LED off RX TALK ON LED will not be on since it s not recording While press TALK button on TX to trigger recording TALK button turns blue LED on RX TALK ON LED will light up and steady green When TX is out of range Blue talk button will be changed by mode LED off Beep gt LED off Vibration gt LED off Beep Vibration gt LED off None While TX comes back in range blue LED will be back on steady When the battery in low blue talk button will be changed by mode LED blink fast gt LED off gt LED blink fast gt LED off 3 Warning MODE MODE Selection button When a user pushes this button the mode is changing in order Beep Tone gt Vibration gt Beep and Vibration gt None 4 M Mute Button When this button is pushed audio data is not output during Talk On mode Talk button will be changed with next mode order LED blink slow gt LED off gt LED blink slow gt LED off DESCRIPTION Transmitter DESCRIPTION HOME CHARGER 3 Battery LED Power Adapter Connector Battery LED In Charging Red LED Fully Charged
4. or any other body part Power Frequency MHz Number of Channel Channel Space Speech Coder Type of Modulation Processing Gain Data Rate Frame Rate Receiver Sensitivity Battery Battery Capacity TX power levels Temperature Range SPECIFICATION DC 12V for RX 902 927MHz Band Width 20Channels 1 2MHz DBPSK SS MODULATION DEMODULATION 32Kbps ADPCM with parity 80Kbps Time Division Duplex 102dBm 82dBm Talking Time 12Hours Charging Time 3Hours Lithium ion 3 7V DC 2000mA 100mW 10mW 1mW 20 C 60 C Dimensions WxDxH TX 54mm x 30 5mm x 83 6mm RX 104mm x388mm x 81 5mm 10 1 92M Samples s 2 Samples Chip
5. WIRELESS TRANSCEIVER SYSTEM TDSS 900 PNA User Guide 900M Hz Series Version 1 5 2 Read this user s guide carefully for safe operation and proper use of the product Features and specifications are subject to change without notification RECOMMENDATIONS BOX CONTENTS Prior to use charge TX at least 3 hours Disconnect the battery or switch the power OFF when TX Set is not in use for long periods 1 Transmitter TX Charge TX Set when not in use for short periods 2 Receiver RX Plug In Microphone MONO TROUBLESHOOTING ee 4 Mounting Bracket for Receiver with screw heck Poi Problems Check Points 5 Rechargeable Li lon Battery Check the battery status No reception Check the connection and cables 6 Leather Pouch Check the communication range 7 External antenna Change the location of RX Set Poor reception Check the communication range 8 Desktop charger for transmitter Static noise Check to see if unit is placed near TV speakers or other electronic devices 9 AC Power supply for desktop charger Check the battery status 10 Charger Stand for Desktop Charger Unit does not Check the power switch on the bottom of respond the unit 11 Straight Type internal antenna Check the connection and cables 12 RF Main Cable 13 In car MIC 14 Instruction Manual TIP2 Preserving the Batteries In order to maintain the optimum capacity of the rechargeable
Download Pdf Manuals
Related Search