Home

Panasonic Arbitrator 360 Operating Instructions

1. 80 Setting the System Name 80 Confirming the port settings eee 81 setting the IP address aececi 82 Streaming is not available at present Upgrading is scheduled for the future Contents continued SOUP oe cche reteset cee esea nests orreeniaee 83 Admin Password cccccceeeeeeeeeeeeeetcteeeeeeeeees 83 Allocation Video Audio ee eeeeeeeeettteeeeeetees 83 Camera Taconis aatinaa aaar Eai 87 Dates THM erana a 89 File Transfigura eoii 90 NGTWOMK orina a a a 91 Embedded OSD ecsnnuncnnennnnnanmienn 92 Radar GP Soi naimisiin itai aa aA 93 Reg Play encsnnacanononna 94 REGIStIALION esnucucsn onana 96 TOJE ansa sipaeiss iedaaeneaderee re eeeaaees 97 Error Messages sanne 98 Messages for the Back End Administrator ADPIICAUOIN sssccssesnvas secavesscarstateninadees ea EEA 98 Messages Common to the Front End ADPIIGAUOM sensisse 107 Messages Common to the Back End Client ADPlIGAtlOM asniensis 113 SUDMESSAGES uo nasu seeds anliden aiteest 114 Camera Connection and Combination of Cameras were ee ee 118 For obtaining the software contact your supplier WE Display in this manual Display on the screen may differ from the actual product Overview An AG JJLBE20P Back End Administrator application is a Windows application to operate videos registered in the Back End Server Back End System Construction The Back End System is composed of the Back End Server database server and Back End
2. Retype Password Re enter the same string of password input in the Password field for reconfirmation Item list Alist of the setting screens is displayed Clicking on a screen name will display the corresponding setting screen OK button For changing the settings of the Memory Card Video Recorder to those set in the Config screen Cancel button For canceling changes 38 Operations continued Allocation Video Audio screen Resolution RecordRate Main The resolution and bit rate of the main video can be set Setting values D1 HI 720x480 high quality mode D1 STD 720x480 standard quality mode D1 10 720x480 10 frames second CIF 352x240 low quality mode Sub The resolution and bit rate of the sub video can be set Setting values D1 HI 720x480 high quality mode D1 STD 720x480 standard quality mode D1 10 720x480 10 frames second CIF 352x240 low quality mode Note If either of the Main or Sub Resolution RecordRate is set to D1 10 the other is also set to D1 10 39 Camera1 Camera2 Camera3 Camera4 Camerad Camera6 Set if a camera is connected to each of CAMERA 1 2 3 4 5 and 6 connectors on the Memory Card Video Recorder When a camera is connected set to ON and when it is not connected set to OFF Operations continued Preset Settings For setting the channel mode and camera connection patt
3. E00460 E00461 Invalid update file was found Update file was not found The update file on the USB memory device is corrupted e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device No update file could be found on the USB memory device e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device 107 Error Messages continued E00462 Two or more update files were found E00463 _ Invalid update file was found E00464 E00465 E00466 Unexpected update failure was found E00467 E00468 Update file was not found This media cannot be used for update Update file cannot be read Unexpected update failure was found E00602 AG RCP30 needs to be updated Will start updating soon E00603 Unsupported Control Panel Replace Control Panel Will power off after uploading Turn ACC ON to cancel power off DSP error This system is rebooting E02431 E02432 E02440 System error Couldn t format cards E02441 Couldn t format cards Message Measure Multiple update files were found on the USB memory device e Check whether there are multiple update files on the USB memory device e Check whe
4. 153 Failed to unlock the contents 154 This status of the contents can not move restore archive 155 An error occurred when adding the information 156 An error occurred when adding the information 157 An error occurred when adding the information 158 An error occurred when deleting the information 159 An error occurred when deleting the information 160 An error occurred when deleting the preset information 161 An error occurred when changing the information 162 An error occurred when changing the information 163 An error occurred when changing the information 201 No case file exists 202 No right to operate the case file 203 The registration number of case file reached to the maximum 204 Failed to add the case file 205 Failed to modify the case file 206 Failed to delete the case file The case file has been assigned to the video 207 Failed to delete the case file 301 No group exists 302 No right to operate the group 303 Failed to add the group 304 Failed to delete the group 305 Failed to add the rights 306 Failed to modify the group information 115 Error Messages continued a E E 307 Failed to add the group 308 The registration number of group is exceeded 309 Failed to update the group information 501 No setting information exists 502 No rights to set up 503 Failed to add the drive setting 504 Failed to add the drive log setting 505 The drive setting has been registered
5. Deletion of the Classify List failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Editing of the Classify List failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 40050 This data has already existed A classify tag with an identical name already exists Specify a different name 40060 Input Classify Tag No classify tag name was input Input a classify tag name 40070 Too many registered data 50000 Failed to update due to illegal data Please confirm the input information Failed to update due to illegal data Please confirm the input information 51000 The number of registered classify tags exceeds 50 Decrease the number of registered classify tags then try again An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct 102 Error Messages continued Message Measure 51010 Too many registered data The number of registered data exceeds the specified value Decrease the number of registered data then try again 51020 A minimum free space is too The minimum size for the archive area is too great Specify a smaller value large The maximum value that can be set is 1000GB 5
6. Operations continued File Transfer screen Upload Auto Upload is Enabled Automatic uploading is enabled when a check mark is placed in the box Server IP Address for Manual Upload Set the IP address of the Back End Server for manual uploading Note This setting is enabled on the Front End application only EXBORIDVD Burn on the recorder T ideos on The method to delete videos on the recorder Select how to delete video files from the Memory Card Video Recorder after atelexporingnon DVD burning Setting values Force Confirmation 4A System Name Set the system name of the Memory Card Video Recorder within 50 characters When the Recorder directly communicates with the Back End system the communication is enabled only when the name set here and that registered in the Back End system are the same Exporting from the Front End application is not available at present Upgrading is scheduled for the future Operations continued Network screen AP Priorit AP Highest E Streaming Server IP Address List Set the IP Addresses of the Back End Server for streaming Up to 5 IP addresses can be registered The Front End application periodically sends packets to these IP addresses The Back End Server recognizes the sender of the received packets as a streaming target A Front End application can connect with a single Back End Server at a t
7. 65 Setting the Rule Effects Z is gt View your own non Arbitrator video files Arbitrator video files AV video without any officer ID View non Arbitrator video files without any officer ID Playback your own Arbitrator video files AV video Playback all Arbitrator video files AV video View all non Arbitrator video files Edit Bookmarks Classify Snapshots Delete Arbitrator video files AV video Delete non Arbitrator video files Obo00000000 oOoo0000000 lt C D Program Files PanasoniclCV Contents Library 1 Click on Add The Evidence Rule User Add Form screen is displayed Evidence Rule User AddForm 2 Select Users on the Users tab 3 Click on Groups and select groups on the Groups tab 4 Click on gt Selected users and groups are moved to the right 5 Click on OK The selected users and groups are added to the Permission Users Groups list on the edit rule screen 6 Check the Allow or Deny check box on the Permission Rights list 7 Enter the retention period in the Store Days field 8 Check the Storage Location Canceling the selection 1 Select users or groups on the right list 2 Click on lt Deleting users or groups To delete selected users or groups on the Permission Users Groups list click on Clear To delete all users or groups on the Permission Users Groups list click on Clear All Operations continued Des
8. a information file cannot be There is no Administrator Registration file or it contains the wrong data Create pagen a correct Administrator Registration file WADMIN TXT copy it to a USB memory device and reload it E22424 Officer s information cannot be Officer data cannot be changed during recording Stop recording and start setup during record a E22425 ee list cannot be There is no classify file or the content of the file is incorrect E22426 Menu copy failed For copying to a USB memory device connect a write enabled USB memory device For copying to a recorder connect a USB memory device that contains data E22427 eee information file cannot be There is no vehicle ID registration file or the content of the file is incorrect E22428 eo ennatien file cannot be There is no shift file or the content of the file is incorrect E22429 Aak file cannot be There is no area registration file or the content of the file is incorrect E22432 Service log copy failed Copying service log is failed Retry copying E22448 ae was canceled to start Streaming starts and the operation is canceled Wait until streaming ends E25410 GPS communication error An error occurred in the GPS module Contact your supplier Please check the GPS module E27200 Finish Upload File transfer was completed F27201 Storage capacity was not enough to Capacity of the server is not enough for uploading data and upload is transfer the
9. 506 Failed to delete the drive setting 507 Failed to valid the drive setting 508 Failed to modify the drive setting 509 Failed to register the server network setting 510 Failed to register the schedule setting 511 Failed to modify the Server network setting 512 Failed to modify the schedule setting 513 Number of the drive setting items is exceeded 514 Failed to search the logical drive 515 Failed to set up the password 516 Failed to set up the system configs 517 Failed to delete the drive due to the assigned drive by the evidence rule 518 Failed to search the drive 519 Failed to add the IP address 520 This database is used by else BES 601 No logs exist 602 No rights exist 603 Failed to add the log 604 Failed to delete the log 701 No machine setting information exist 702 No rights exist 703 Failed to register the machine information 704 Failed to register the machine group information 705 Failed to register the software 706 Failed to register the released software 707 Failed to register the installation 708 Failed to modify the machine information 709 Failed to modify the machine group 710 Failed to modify the software 711 Failed to modify the released software 712 Failed to modify the installation 713 Released software has existed 714 No software information exists 715 No machine setting group exists 716 No released software exists 717 The officer has existed 718 The softw
10. 52120 Failed to get the schedule Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made Failed to set the information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Failed to set the drive information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Failed to set the schedule Data writing failed Verify with the administrator that the BES and DB have information started Check also that the network connection is properly made This folder cannot be used The As the specified file path is too long this folder cannot be used Specify a file specified file path is too long The path within 200 characters file path that can be specified is within 200 characters Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 103 Error Messages continued No Message Measure The period until E mail is A retention period until the e mail is transmitted exceeds the limit The transmitted is too long The maximum period that can be set is 30 days maximum terms that can be set are 30
11. Check also that the network connection is properly made 104 Error Messages continued Message Measure 55240 IP address cannot be registered The number of registered IP addresses exceeds the specified value any further Decrease the number of registered IP addresses then try again 60000 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 60010 Illegal IP address range Input Invalid data are input Input a value in the range of 0 to 255 the number between 0 and 255 60020 Illegal IP address range Input An invalid value is input A value greater than that of the From address must the larger number at To than be input as the To address From 60100 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 60110 Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 60120 Failed to get the drive information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 60130 Fail to get the informatio
12. Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device Multiple update files were found on the USB memory device e Check whether there are multiple update files on the USB memory device e Check whether there are multiple USB memory devices containing update files The update file on the USB memory device is corrupted e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device No update file could be found on the USB memory device e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device The used USB memory device cannot be used for updating e A USB memory device containing a folder other than the WIDKEY folder cannot be used for updating An update file load error occurred e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device Some other update error occurred e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device
13. Updating the Front End application If the Valid check box is checked the Back End Server detects the checked PC and updates it automatically The version of the updating software is displayed in the Update Version field Note that without registering the Front End application the Valid check box cannot be checked and Select All and Clear All are not active Selecting all Front End applications Click on Select All All Valid check boxes will be checked Clearing selection of all Front End applications Click on Clear All All Valid check boxes will be unchecked 28 Registering the Front End application Only one version of the Front End application can be registered in the Back End Server When a new version is registered the old one will be deleted 1 Click on Register The file selection dialog box appears 2 Select the update module for the Front End application 3 Click on Open The update module is checked if it is correct The application is registered if the module is correct If it is not correct an error message appears Updating the Front End Update screen Click on Refresh The screen will be updated Operations continued Deleting PC on which Front End application is running 1 Select PCs to be deleted on the Front End Application list 2 Click on Delete A confirmation dialog box is displayed 3 Click on Yes The selected PCs will be deleted from the list Can
14. check that it is the hexadecimal number using characters 0 9 a f A F The same IP Address cannot be set for PC LAN UPLOAD LAN and WIRELESS LAN e Set the different IP Address The specified snapshot folder does not exist e If the snapshot folder is stored in a removable medium check that the removable medium is connected to the PC As the specified snapshot file is not in the specified snapshot folder that snapshot image cannot be sent by e mail e If the storage location of a snapshot file is changed transmission of the file is not possible 106 Error Messages continued Messages Common to the Front End Application Message Measure E00410 E00411 E00412 E00413 E00414 E00415 E00418 E00419 E00420 E00449 Invalid update file was found Update file was not found Two or more update files were found Invalid update file was found Update file was not found This media cannot be used for update Update file cannot be read Unexpected update failure was found The update file on the USB memory device is corrupted e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device No update file could be found on the USB memory device e Check whether the update file for the recorder has been correctly copied to the USB memory device
15. 200 Display Select a trigger code that is to be displayed ona video Setting values OFF Ato Z Next button For displaying the Setup screen for Trigger 9 to Trigger 16 Prev button For displaying the Setup screen for Trigger 1 to Trigger 8 Operations continued Registering Users User registration as an administrator or an officer is required for use of the Back End Administrator or Back End Client application or Front End application When the Back End Administrator application is installed a user named Arbitrator who has all rights and cannot be deleted is registered On the user registration screen registering a new user viewing registered users changing the registered user information and deleting user registration are enabled Click on Users The Users screen will be displayed iministrator 2 0 99 51 j Groups Rules Classify Config Arbitrator 300 Back E Update Users Adding the user 1 Click on Add The Property screen will be displayed 2 Enter the User information 55 Note Specify the rights to be given to the user Check the rights to be given to the user on the Right List For selecting all rights Click on Select All For releasing all right Click on Clear All Set a group Select a group on the All other groups List then click on gt Click on OK The Property screen will close and the user will be registered For the
16. Administrator and Back End Client applications The Back End Server receives videos and meta information from the Front End application or the Memory Card Video Recorder and stores them in its storage area The meta information is registered in the database server The Back End application is composed of two parts one for an administrator Back End Administrator and another for an officer Back End Client The Back End Administrator application enables updating of software user management system setting etc The Back End Client application enables searching for videos stored in the Back End Server playing videos found videos exporting data etc The Back End System also includes the Service Watch application which monitors operation logs of the Back End system in real time Windows server Windows server Streaming is not available at present Upgrading is scheduled for the future Overview continued Multi Server System The Back End system has multiple servers that are independent of one another and one Back End Server has its own database The Front End application can upload videos to any Back End Server When the Back End Client user is logged in the user selects one of multiple servers and a search operation is enabled on the selected Back End Server only SQL Server on WMware District 1 Vehicle VPU FE Functions The Back End Administrator application allows an administrat
17. Classify Both Allow and Deny check boxes are not checked simultaneously Enter the information or select the information on the dropdown list Officer1 OK The rule is saved in the database Officer2 Cancel Editing rules is canceled Bookmark Note Unit e If Allow for Playback your own Arbitrator video files AV video on the Permission Rights list is checked Allow Shift for View your own non Arbitrator video files is also checked automatically Area e If Allow for Playback all Arbitrator video files AV video z on the Permission Rights list is checked Allow for View VehiclelD all non Arbitrator video files is also checked automatically Note Agency Unit Shift Area and VehiclelD are the default setting for Field1 to Field5 The field name can be changed upon installation of the Back End Server 66 Operations continued Description of Evidence Rule User Editing a rule AddForm screen Update Us Rules Classify Config 1 Click on Edit The edit rule screen appears 2 Edit the rules Users Alist of users stored in the Back End Server is displayed Groups A list of groups stored in the Back End Server is displayed _ gt Users or groups selected on the Users tab or Groups tab are transferred to the right list and selection is fixed lt Users or groups selected on the right list are transferred to the Use
18. Manage Rules Allow the user to create delete modify the evidence rules Evaluate Rules Allow the user to evaluate the evidence rules Manage Classify Allow the user to create delete modify the Classify information Change system config settings Allow the user to modify the system config settings View your own non Arbitrator video files Allow the user to see files associated to their user Playback Arbitrator video files AV video without any officer ID Allows the user to playback AV videos without any officer ID View non Arbitrator video files without any officer ID Allow the user to playback files without any officer ID except AV videos Playback your own Arbitrator video files AV video Allow the user to playback AV videos associated to their user Playback all Arbitrator video files AV video Allow the user to playback all AV video files View all non Arbitrator video files Allow the user to see all files except AV videos Edit Bookmarks Classify Snapshots Allows the user to create delete modify Bookmarks Classify and Snapshots Delete Arbitrator video files AV video Allow the user to delete AV video files Delete non Arbitrator video files Allow the user to delete files except AV videos Verify Arbitrator video files AV video Allow the user to run a file integrity check of the AV video files Export Arbitrator vi
19. Setting values ON OFF Rule of World Time Rules of filename for recording files Filename Setting values World Time Local Time Power On Rec OFF Automatic start of recording upon power on Setting values ON OFF Record sound OFF Setting of a beep during recording Setting values ON OFF GPO GPO settings GPO1 Signal OFF Setting of output signals to GPO1 Setting values OFF REC ERROR REC ERROR GPO2 Signal OFF Setting of output signals to GPO2 Setting values OFF REC ERROR REC ERROR GPO3 Signal OFF Setting of output signals to GPO3 Setting values OFF REC Auto Power Off Settings upon automatic power off Power Off Time After Upload Time required from the ACC signal is turned off up to the Memory Card min Video Recorder is turned off minutes Setting values 0 10 20 30 60 90 120 180 After Upload Apply To APPLICATION When Power Off Time is set to After Upload select which one s uploading AND LAPTOP _ is to be observed Setting values APPLICATION ONLY LAPTOP ONLY APPLICATION AND LAPTOP Action Specified Lock When Power Off Time is set to After Upload select an action Setting values Close Lock Log off Shutdown Stand by Timeout s 120 When Power Off Time is set to After Upload select time required for the Memory Card Video Recorder to shut itself off after the specified action Seconds Setting values 30 60 90 120 to be continued to the next page 94 Setup continued Item Facto
20. after atalexponinglon DVD burning Force Automatically deleted Confirmation A confirmation message is displayed Certification System Name System name of the Memory Card Video Recorder Exporting from the Front End application is not available at present Upgrading is scheduled for the future 90 Setup continued Network The network settings can be performed Item Factory Preset Description Streaming is not available at present Upgrading is scheduled for the future Recorder PC LAN Setting of the LAN port on the Memory Card Video Recorder for connection with the Front End server DHCP Server1 Setting of whether the port will serve as a DHCP server or not Setting values OFF Server1 Server2 Server3 Server4 Recorder UPLOAD LAN Setting of the wired LAN port on the Memory Card Video Recorder for connection with the Back End Server DHCP Client Setting of whether setting data will be obtained from the DHCP server or not Setting values OFF Client Recorder USB WIRELESS LAN Setting of the wireless LAN port on the Memory Card Video Recorder for connection with the Back End Server DHCP Client Setting of whether setting data will be obtained from the DHCP server or not Setting values OFF Client AP Priority AP Highest Set the priority of connection order to the access points Setting values AP Highest Random 1 If Server1 Server2 Serve
21. external media and be registered in the database 0 51 Rules Classify Config 1 Click on Import The file selection dialog box appears Select a file to be registered Click on Open User information and group information will be registered in the database Operations continued Exporting users User information and group information registered in the database will be exported to external media and stored as files Update Users Groups Rules Classify Config 1 Click on Export A file storage dialog box is displayed 2 Enter the save file name 3 Click on Save User information file or group information file will be exported to the specified folder 61 Operations continued Registering Groups 4 Set the users Select users to be grouped on the All Other Users list and click on gt gt When users are grouped rights are given to multiple users at one time If different rights are given to a group and the users who belong to the group the rights which z are given to both a group and users are applied Click on OK Click on Groups The Groups screen is displayed The Property screen is closed and the group will be registered Multiple users can be selected Arbitrator 360 Back End Administrator 2 0 39 51 Update Users ups Rules Classify Config Description of the Property screen Adding groups 1 Click on Add ID Enter th The Property screen
22. file canceled E27202 File transfer was completed Upload was completed but video files not restored remain on the SDHC Restore file remained Memory Card E27203 File not found in SDHC cards No file for uploading is found on an SDHC Memory Card E27401 Write Protect cards found A read only SDHC Memory Card is found and uploading cannot be started Couldn t start file transfer E27403 Media error f A read write error has occurred on the media Replace the SDHC Memory File transfer was incomplete Card E27405 Storage write error A verifying error has occurred in the server storage and upload cannot be File transfer was incomplete completed E27407 No SDHC Cards found No SDHC Memory Card is inserted and upload cannot be started Couldn t start file transfer E27430 Couldn t start file transfer Upload cannot be started Check the network connection 27431 _ File transfer was incomplete Upload cannot be completed because of the network trouble E27499 System error A system error has occurred and upload cannot be completed File transfer was incomplete E28200 Finish Export Export was completed E28201 USB storage capacity was not Use other USB memory device that is not full enough to export Error Messages continued Message Measure E28202 Export was completed Restore the file not yet restored and export it again Restore file remained E28203 File not found in SDHC cards There a
23. following cases an error message appears e The user ID is not entered e The user ID is not unique e The password is different from the retyped password e Password character s and or length is wrong e The upper limit of number of registered users is exceeded e The user registered to the Memory Card Video Recorder exceeds 1 000 Operations continued Description of the Property screen AIll other groups List The group list to which the user does not belong is displayed Right clicking enables the same operation as clicking on gt Groups List The group list to which the user belongs is displayed Right clicking enables the same operation as clicking on lt vi C Delete non Arbitrator video files ID Enter the user ID used on logging in Upper and lower case letters are not distinguished Name Enter the user name First first name Middle middle name Last Last name E mail Address Enter the e mail address of the user Account is disabled If checked the user registered on the Memory Card Video Recorder cannot log in Register to Recorder If checked for one or more users they will be registered on the Memory Card Video Recorder connected to the Back End Server Note that the Officer list of the recorder will be overwritten upon the registration If Account is disabled is checked this setting is disabled If the users are registered on the Officer list of the rec
24. have started Check also that the network connection is properly made Acquisition of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 41050 No Rules Name input 41060 Input Storage Days No evidence rule name was input Input the rule name No storage period has been input Input a storage period 41070 Check Storage Location No storage location is specified Specify a storage location 41080 Check permission No account is specified Specify an account 41090 The retention period is too long The maximum terms that can be set are 4000 days Failed to update due to illegal data Please confirm the input information Failed to get the classify information 40000 40010 Failed to delete the classify information Failed to add the classify information Failed to edit the classify information The specified storage duration exceeds the limit Specify within the predetermined range An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Acquisition of the Classify List failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Deletion of the Classify List failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made
25. in the Rule Effects section are disabled even if a user setting or group setting specifies enabling the rights 64 Default rule If no rule is applied to the files the default rule will be applied The default rule is created when the Back End Server is installed The Effects of the default rule are as shown below Access permission No right Retention period 90 days Storage location First storage location registered on the Configuration Settings screen The Default rule cannot be deleted Only Store Days and Storage Location in Rule Effects can be edited Operations continued Adding a rule 39 51 Rules Classify Config 1 Click on Add The edit rule screen appears 2 Enter the rule name in the Rule Name field on a a a a a a a a a elete video jelete nor les L D Program Files PanasoniciCv Contents Library 3 Make settings for Criteria Enter the text or select on the dropdown list 4 Make setting for Rule Effects See Setting the Rule Effects on the right 5 Click on OK The rule is added on the Rules screen 6 Click on Apply The rule is registered in the database Note For the following cases an error message appears e No rule name is entered e The entered rule name has already been registered e Permission Users Groups is set but Permission Rights is not set e Retention period is not specified e Storage location is not specified
26. input to the CAMERA 1 connector E29402 No CAMERA2 video signal CAMERA 2 connector input cannot be detected Check whether the signal is input to the CAMERA 2 connector E29403 No CAMERAS video signal CAMERA 3 connector input cannot be detected Check whether the signal is input to the CAMERA 3 connector E29404 No CAMERAS video signal CAMERA 4 connector input cannot be detected Check whether the signal is input to the CAMERA 4 connector E29405 No CAMERAS video signal CAMERA 5 connector input cannot be detected Check whether the signal is input to the CAMERA 5 connector E29406 No CAMERAS video signal CAMERA 6 connector input cannot be detected Check whether the signal is input to the CAMERA 6 connector E30400 Network setting parameter error Network settings are not correct Check the network settings 112 Error Messages continued Messages Common to the Back End Client Application No Message Measure 1000 Failed to update due to illegal Reinstall data Please confirm the input information 1010 No Back End Server input Enter the server then perform operations 1020 No userlD input Enter the user name then perform operations 1030 No password setting Set the Enter the password then perform operations password 1060 Failed to login Check the entered information again then perform operations 1070 Failed to get the login user Check the entered information ag
27. j The Back End Administrator application can be Installing the Back End remotely updated when the latest version of the Back Administrator application End Administrator application is registered in the Back To install the Back End Administrator application End Server the Back End Server application must be installed When the Back End Administrator application receives For installation of the Back End Server refer to the the update module from the Back End Server it is Operating Instructions for the Service Watch automatically updated upon being restarted 1 Start the Internet Explorer Notes 2 Access to http IP address of the Back End Server 12430 Admin exe e If the Interactive services dialog detection dialog box is displayed select Show me the message If a dialog box prompting you to select Try Again 3 Enter the IP address of the Back End Continue or Exit Installation is displayed select Server and click on Update The License Agreement screen appears The Update module is downloaded and executed Continue 4 Select I Agree The Installation Complete screen appears 5 Click on Close The login dialog box appears 6 Enter the Server IP address User Password and click on Login A shortcut icon is placed on the desktop Installing Uninstalling continued Uninstalling Uninstall the Back End Administrator application following the procedures below Procedures for W
28. of the firmware of the Memory Card Video Recorder detected by the Back End Server is displayed The Back End Server identifies a Memory Card Video Recorder by using the MAC address of the recorder for connecting to the Front End application When a recorder is detected for the first time it is registered in the database If the Valid check box is not checked the Back End Server updates the items on the recorder list each time it detects the recorder Note that the recorder list on the screen is not updated before clicking on the Refresh button In the Update Version field the latest version appears 31 Editing Vehicle ID Only when the Valid check box is not checked Vehicle ID can be edited Click on the cell to be edited If the Valid check box is checked Vehicle ID is not updated when the Memory Card Video Recorder is detected It cannot be edited Updating the recorder When the Valid check box is checked the Back End Server detects the checked Memory Card Video Recorder and transfers the firmware automatically However Field5 Source in the database is not updated To update the Memory Card Video Recorder after firmware transfer reboot it Selecting all recorders Click on Select All All Valid check boxes will be checked Clearing selection of all recorders Click on Clear All All Valid check boxes will be unchecked Operations continued Registering firmware Only one version of the firmware c
29. the input information Failed to get the group Information 41020 Failed to get the free field information Failed to get the drive information Message Measure Acquisition of the group list failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the list of free fields failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Deletion of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Addition of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Editing of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Updating of evidence rules failed An identical evidence rule name already exists Input a different evidence rule name An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Acquisition of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of evidence rules failed Verify with the administrator that the BES and DB
30. time becomes shorter than the set value Setting values ON OFF Operations continued Registration screen Meta Definition Meta Definition Select the type of meta definition to be registered to the Memory Card Video Recorder Setting values Administrator Agency Unit Shift Area VehiclelD Note Meta Definitions can be changed when installing the Back End Server Load button For loading data specified at Meta Definition and registering the data to the Memory Card Video Recorder Meta Definition list The meta definition data loaded are displayed on this list 52 Allow Guest Login Select if login of a user who has not been registered in the Back End Server or the Memory Card Video Recorder is permitted or not Setting values ON OFF Login using your current login account in the operating system When set to ON if the current login user name to the PC is the same as that to the Front End application the login screen with the password entered will be displayed Setting values ON OFF Note This setting is enabled on the Front End application only Clear User Information on Recorder when logout Select if the user information of the Memory Card Video Recorder is deleted upon logoff Setting values ON OFF Operations continued Limited Operation Disable Operation for Set the operation prohibited by a user Setting values STOP
31. 0 Select the other folder Failed to export AVViewer The time for setting day night view is the same Please set another time There is no last error Please input both IP address and the subnet mask Either of IP address the subnet mask or the default gateway value is not correct Please input again IP address is not correct Please input again Invalid the gateway address Invalid the subnet mask Message Measure A different preset setting has been made with an identical preset No e Use a different preset No Invalid camera connection e Connect 2 or more cameras e Connect any of Cameras 1 to 3 When Preset 3 has been set None cannot be specified for Preset 2 The retyped password is different Input the password again Up to xxx characters can be used in a folder name Select another folder An invalid character is included Input again The available characters are lt 3Ch gt 3Eh 5Ch amp 26h 2Ch control characters OOh 1Fh and one byte alphanumerics and symbols except for DELETE 7Fh Exporting of AV Viewer failed e Check that there is sufficient free space on the destination medium e Check if the medium is write protected e Check that writing to the destination medium is authorized e Reinstall AV Viewer Identical times are set for switching the day night views e Set different times There is no last error log Specify b
32. 1030 The retention period of the illegal The specified preservation duration exceeds the limit Specify within the video is too long The maximum predetermined range terms that can be set are 4000 days Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Failed to get the drive information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 51120 Failed to get the schedule Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made 51200 Failed to set the information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 51210 Fail to set the drive information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 51220 Failed to set the schedule Data writing failed Verify with the administrator that the BES and DB have information started Check also that the network connection is properly made 51230 This folder has been registered As the folder has been already registered registration of that fold
33. 2 Browse button For opening the Server Folder Setting dialog box for selecting the Archive Folder Unprocessed video setting Settings for the Unprocessed Video Folder will be made When the video is verified and unprocessed e mail is automatically sent to the users who belong to the group specified in Alert Setting See Schedule setting screen page 22 Consult your supplier Unprocessed Video Folder For displaying the full folder path for the Unprocessed Video Folder Unprocessed video save period The retention period of the unprocessed video file is fixed to unlimited Browse button For opening the Server Folder Setting dialog box for selecting the Unprocessed Video Folder Description of the Screen Displays continued Log setting screen When the Log setting tab on the Config screen is clicked on the log setting screen is displayed See Log Setting page 74 Arbitrator 3611 Back End Administra s Update Users Gr 3 Rules Classify Config Operation log setting Settings for the user operation log will be made Log Retention Period For specifying the retention period of the user operation log If the Log Retention Period is set to 0 the retention period will be unlimited Front End Application Recorder Log setting Settings for the log of the Front End application and Memory Card Video Recorder will be made Root Path of Front End Recorde
34. Enter a GPI trigger name Action NONE Action when a trigger signal GPI1 16 is detected Setting values NONE No action REC recording STOP stop AUTOZOOM Automatic zoom in pause for a specified time then zoom out CAM1LED Switching lit unlit of the REC lamp of the color camera connected with the CAMERA 1 input connector Preset 1 input selected Preset 2 input selected Preset 3 input selected Recording of Preset 1 input video Recording of Preset 2 input video Recording of Preset 3 input video Recording of AUDIO IN2 input No recording of AUDIO IN2 input Recording starts upon a TGT input Recording of input signals set in Preset1 starts upon a TGT input TGT P2REC Recording of input signals set in Preset2 starts upon a TGT input TGT P3REC Recording of input signals set in Preset3 starts upon a TGT input OWN REC Recording starts upon a OWN input OWN P1REC Recording of input signals set in Preset starts upon an OWN input OWN P2REC Recording of input signals set in Preset2 starts upon an OWN input OWN P3REC Recording of input signals set in Preset3 starts upon an OWN input Preset 1 Preset 2 Preset 3 Preset 1 Rec Preset 2 Rec Preset 3 Rec AUDIO20N AUDIO2MUTE TGT REC TGT P1REC ON Nn nnn nT no Detection High Detection method for trigger signals GPI1 16 The selectable detection methods vary depend
35. Exit 26 Startup and Termination continued Terminating Click on the close button at the upper right on the Main screen The application is terminated and the screen is closed Arbitrator 3611 Baci assi Update Rules Classify Config Note While updating the error message appears and the application cannot be terminated 27 Operations Updating The Back End Administrator application can remotely update the Front End application and Memory Card Video Recorder as well as the Back End system itself Updating the Front End application The latest version of the Front End application is sent to the PC with the Front End application installed via wired or wireless LAN for updating the application Click on the Front End Update tab The Front End Update screen appears On this screen confirmation of the update status of the Front End application and registration of the Front End application to the Back End Server are enabled 0 Back End Administrator 2 0 99 51 Users Groups Rules Classify Config Arbitrator 301 Update Confirming the update status of the Front End applications On the Front End Update screen a list of PCs on which Front End application is running detected by the Back End Server is displayed On the list the version and date and time of last update of each Front End application are displayed In the Update Version field the latest version appears
36. HCP Select if the IP address for the wired LAN port on the Memory Card Video Recorder will be obtained from the DHCP server or not Setting values OFF Client IP Address Set the IP address This setting is enabled when DHCP is set to OFF Subnet Mask Set the subnet mask This setting is enabled when DHCP is set to OFF Gateway Set the default gateway This setting is enabled when DHCP is set to OFF Operations continued Recorder USB WIRELESS LAN The settings for the USB wireless LAN port on the Memory Card Video Recorder that is used for connecting the Back End Server can be performed DHCP Select if the IP address for the USB wireless LAN port on the Memory Card Video Recorder will be obtained from the DHCP server or not Setting values OFF Client IP Address Set the IP address This setting is enabled when DHCP is set to OFF Subnet Mask Set the subnet mask This setting is enabled when DHCP is set to OFF Gateway Set the default gateway This setting is enabled when DHCP is set to OFF AP Priority Set the priority of connections to the access points Setting values AP Highest Random SSID List For displaying the SSIDs for the access points Up to 10 SSIDs are displayed Property button For editing data of the access point selected in the SSID List Click to display the Access Point Setting screen Move Up button For raising the priority of the connec
37. OFF Simple Operation Mode Only When set to ON a user can use only Simple Operation mode Regardless of this setting the administrator can use both Simple Operation mode and Full Operation mode Setting values ON OFF Note This setting is enabled on the Front End application only EXBGHRIDVD burn Operation Set if XPGRRERG DVD burn is enabled by a user Setting values ENABLE DISABLE Exporting from the Front End application is not available at present Upgrading is scheduled for the future 53 Operations continued Triggers screen Trigger Set if the GPI trigger function is used or not Setting values ON OFF Trigger 1 Trigger 16 Name Specify the name of a GPI trigger with up to 15 characters Action Select the action of a GPI trigger Setting values lt Trigger 1 Trigger 16 gt NONE REC STOP AUTOZOOM CAM1LED Preset 1 Preset 2 Preset 3 Preset 1 Rec Preset 2 Rec Preset 3 Rec AUDIO2ON AUDIO2MUTE lt Trigger 15 Trigger 16 gt TGT REC TGT P1REC TGT P2REC TGT P3REC OWN REC OWN P1REC OWN P2REC OWN P3REC Note TGT and OWN can be set to either Trigger 15 or Trigger 16 but not to both of them 54 lor or lor CE CE o E CE lor lor Detection Select the condition for a GPI trigger to action Setting values lt Trigger 1 16 gt Low High Both Level High Level Low lt Trigger 15 16 gt OFF 1 2
38. Panasonic Operating Instructions Back End Administrator Back End Application Model No AG JJ LBE20P yOUGHBOOR Arbitrator 360 mobile digital video system Streaming Convert Copy and Exporting from the Front End Application are not available at present Upgrading is scheduled for the future n this manual each explanation for streaming from the Back End Application and convert copy and exporting from the Front End Application is enclosed in a colored frame like I e Microsoft and the Microsoft logo Windows are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries ENGLISH 1009K0 MI VQT2D94 Contents Overview oS TEETE 4 Back End System Construction 4 Multi Server Syste cco isnn ianei ir 5 Fino S eana ens tecaeseeesepeeeaaann 5 Operating Environment eceeceeeeeeeeeeeteees 6 Installing Uninstalling 7 Ea EE A E meee 7 Installing the Back End Administrator applicatio Messiren na 7 Remote updating ccccccecceeeeeeeeeseeceeaeeeeeees 7 Uninstalling aaa 8 Procedures for Windows XP seessseesseesrirsess 8 Procedures for Windows Vista 0 ceceeeeee 8 Description of the Screen DiS plays eee eee ee 9 Main SChOOMN esensina a 9 TOOID AN asa A 9 Update Screen ssie sussie aterari iian 10 Front End Update screen sceeeeeeeeteees 11 Back End Update screen c cseeeeseeee
39. Recorder upon power on Setting values ON OFF LAST Init AE Shift Set the brightness of images upon power on of the Memory Card Video Recorder Setting values 2 1 0 1 2 LAST Init LPR Mode Set if the LPR mode is enabled or not upon power on of the Memory Card Video Recorder Setting values ENABLE DISABLE Operations continued Date Time screen Time Zone Set the time zone Setting values Hawaii Standard Time Yukon Standard Time Yukon Daylight Saving Time Pacific Standard Time Pacific Daylight Saving Time Mountain Standard Time Mountain Daylight Saving Time Central Standard Time Central Daylight Saving Time Eastern Standard Time Eastern Daylight Saving Time Atlantic Standard Time Atlantic Daylight Saving Time Asia Tokyo Date Time Style Set the display pattern of date and time Setting values ISO USA 43 Day Night View Select if Day and Auto Switch Night views are automatically switched or not When a check mark is placed in the box Day Night views are switched automatically Note This setting is enabled on the Front End application only Switch to Day View at Set the time when Night mode is changed to Day mode Setting range 00 00 00 AM 11 59 59 PM Switch to Night view at Set the time when Day mode is changed to Night mode Setting range 00 00 00 AM 11 59 59 PM Note Displayed time 12 24 hour system depends on the setting on your PC
40. System setting is not authorized Obtain system setting authority for the user or group with BEA An error was generated A program bug is suspected This application has already started An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES has started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while data was being written Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while data was being written Verify w
41. The settings can be edited and be saved with a different name which enables creating and saving multiple recorder settings Click on the Recorder Setting Update tab The Recorder Setting Update screen appears 1 Click on Settings The Recorder Setting screen is displayed 2 Click on Add The editing screen for the Recorder Setting is displayed OO Setting Name Name of the Memory Card Video Recorder settings _ Item Setting category Setting section 33 Operations continued 3 Enter the name of settings to be created in Editing the Memory Card Video Recorder the Recorder Setting Name field settings 4 Select a category to be set on the Item list 5 Make necessary settings on the setting section See Memory Card Video Recorder Configuration Setting Screen page 38 6 Click on OK The settings are registered and the Recorder Setting screen is updated Note If you change the displayed configuration setting screen without clicking on OK after changing settings Save 1 Click on Settings and Apply Changes appears Click on OK then change The Recorder Setting screen is displayed the screen 2 Select a Recorder Setting Name to be edited on the Recorder Setting list 3 Click on Edit The editing screen for the Recorder Setting is displayed Recorder Setting LAST 4 Edit the settings 5 Click on OK The settings are upda
42. Update Users Groups Rules Classify Config 1 Select a group to be deleted on the Groups 1 Click on Property List The Property screen appears and the group information is displayed 2 Click on Delete A confirmation dialog box is displayed 3 Click on Yes The confirmation dialog box is closed and the group will be deleted 2 Edit the group information Property Group Information Cancel deleting Click on No in the confirmation dialog box O Change system config settings E2 View your own non Arbitrator video files L Playback Arbitrator video files AV video without any officer ID C View non Arbitrator video files without any officer ID Playback your own Arbitrator video files AV video C Playback all Arbitrator video files AV video E View all non Arbitrator video files C Edit Bookmarks Classify Snapshots C Delete Arbitrator video files AV video C Delete non Arbitrator video files C Verify Arbitrator video files AV video C Export Arbitrator video files AV video C Export non Arbitrator video files Note Group ID cannot be edited 3 Click on OK The Property screen is closed and the group information is updated 63 Operations continued Setting Evidence Rules An evidence rule is a function to determine access permissions retention period and storage locations of files called Effect by predefined conditions called Criteria whe
43. Update Users Groups Rules Classify Config Front End Update tab For displaying the screen for updating the Front End application See Front End Update screen page 11 and Updating the Front End application page 28 Back End Update tab For displaying the screen for updating the Back End Administrator application Back End Client application See Back End Update screen page 12 and Updating the Back End Administrator and Back End Client applications page 29 Recorder Update tab For displaying the Remote Update screen for updating firmware of the Memory Card Video Recorder See Recorder Update screen page 13 and Updating the firmware of the Memory Card Video Recorder page 31 Recorder Setting Update tab For displaying the Remote Update screen for updating the configuration settings for the Memory Card Video Recorder See Recorder Setting Update screen page 14 and Updating the recorder settings page 33 10 Description of the Screen Displays continued Front End Update screen When the Front End Update tab on the Update screen is clicked on the Front End Update screen appears The Front End application will be updated by transferring the latest version from the Back End Server to the Front End application via LAN or WLAN See Updating the Front End application page 28 Arbitrater aon Back End Administ ator 2 0 9 51 Rules Classi y Config Update Users Grou
44. abled on the Front End application only Action Specified When Power Off Time is set to After Upload select which action is to be taken by the subject s after uploading is completed Setting values Setting values depend on the setting of Apply To APPLICATION ONLY Close LAPTOP ONLY Lock Stand by APPLICATION AND LAPTOP Lock Log off Shutdown Stand by Note This setting is enabled on the Front End application only Timeout s When Power Off Time is set to After Upload select the time required from the specified action is taken till the Memory Card Video Recorder is turned off Setting values 30 60 90 120 seconds Notes e This setting is enabled on the Front End application only e When the vehicle s ignition switch is set to ACC OFF with Upload Mode on the File Transfer screen in Config setup set to MANUAL and Power Off Time on the Rec Play screen set to AUTO uploading will start automatically Classify Cla Classify Tags List The names of the registered classify tags are displayed Up to 50 classify tags can be registered Force Classify Set if the user is forced to add classify information at the end of recording Setting values DISABLE ENABLE FORCE Add button Click to display the Classify Tag Select screen Classify tags registered on the Classify screen are displayed on the Not Belong list Select Classify tags and click on t
45. ain then perform operations information 1080 Failed to get the password End the application and login again information 1090 Failed to login Check the entered information again then perform operations 1100 Failed to update due to illegal End the application and login again data Please confirm the input information 1130 No Correct Password Check the entered information again then perform operations 1140 Failed to set the password Check the entered information again then perform operations infomation 2010 Invalid password length Change Check the entered information again then perform operations password 2020 Invalid password Not included Check the entered information again then perform operations the capital and small letters in the password Change the password 2030 Invalid password Not include the Check the entered information again then perform operations number in the password Change the password 2040 Invalid and expired password Change the password following the screen displayed Change password 113 Error Messages continued Submessages The messages shown below are displayed together with the messages with code number 1000 and higher like 1000 1 Failed to update the user information 7 Wrong password Failed to add the user rights Number of users were exceeded No update time for the user wo 12 14 6 oi i 108 Failed t
46. an be registered in the Back End Server When a new version is registered the old one will be deleted Arbitrater 300 Back End Administrator 2 0 39 51 Update Rules Groups Users Classify Config 1 Click on Register The file selection dialog box appears Select the update firmware for the recorder Click on Open The update firmware is checked if it is correct The application is registered if the firmware is correct If it is not correct an error message appears Updating the Recorder Update screen Click on Refresh The screen will be updated 32 Deleting the recorder Rules Classify Config 1 Select a recorder to be deleted on the Recorder Firmware list Click on Delete A confirmation dialog box is displayed Click on Yes The selected recorder will be deleted from the list Cancel deleting Click on No in the confirmation dialog box Operations continued Updating the recorder settings Creating the Memory Card Video Recorder settings The configuration settings for the Memory Card Video Recorder can be updated via LAN or Wireless LAN Setting items are the same as those set in administrator setup of the Front End application If Memory Card Video Recorders are grouped the settings on all recorders belonging to a group will be updated at one time When the Back End Server is installed the recorder setting is created with the name Default recorder settings
47. appears The Back End Administrator application and or the Back End Client application will be updated by transferring the latest version from the Back End Server to the Back End Administrator and Back End Client applications See Updating the Back End Administrator and Back End Client applications page 29 Refresh button For refreshing the Back End list for Back End Administrator for Back End Client Update Version display For displaying the software version for updating Register button For registering the Back End Administrator or Back End Client application to the Back End Server Back End list For displaying the list of the Back End Administrator or Back End Client application detected by the Back End Server Right clicking enables deleting the Back End Administrator or Back End Client application and refreshing the screen PC Name Name of the PC with the Back End Administrator or Back End Client application installed Version The current version of the Back End Administrator or Back End Client application installed Last Update Date Time The last applying date and time of the Back End Administrator or Back End Client application Status The update status of the Back End Administrator or Back End Client application e Wait for Update Updating e Updated e Disconnected 12 Description of the Screen Displays continued Recorder Update screen When the Recorder Update tab on t
48. are has existed 719 The install information has existed 720 No update module exists 721 No update module path exists in DB 722 Failed to locate the update module 723 The install information has existed 116 Error Messages continued a E E T 724 Failed to delete the machine 725 Failed to delete the machine group 726 Failed to delete the machine software 727 Failed to delete the machine release file 728 Failed to delete the machine release software 729 Failed to delete the installed machine 801 No free field exists 802 Failed to set the free field 900 No Classify exists 901 No right to operate Classify 902 Failed to add Classify 903 The registration number of Classify reached to the maximum 904 Failed to delete Classify 905 Failed to modify Classify Failed to add Classify patterns 907 Failed to delete Classify patterns 908 Failed to modify Classify patterns No Classify patterns exist 910 Failed to modify Classify due to linking to the machine 911 Failed to modify Classify due to linking to the group 1000 A limit is exaggerated 2601 This item already existed in DB 2627 This item already existed in DB 3000 Failed to connect 3001 Time out 3002 Stopped the process 3003 Failed to transfer 5000 Illegal query 5001 Exceptional error on DB Server 5002 Illegal connection to DB 6000 No support 6001 Unknown error on Server 6002 lillegal parameter 6003 Invalid request 6004 No fil
49. b is selected Right clicking enables the operation of the lt button and displaying the list if users registered to the group Operations continued Displaying and editing the user information Rules Classify Config 1 Click on Property The Property screen appears and the registered user information is displayed 2 Edit the user information I Import Arbitrator video files AV video E import non Arbitrator video fi C Operate Live Streaming C Change system config settings 2 View your own non Arbitrator video files Playback Arbitrator video fles AV video without any officer ID Note User ID cannot be edited 3 Click on OK The Property screen is closed and the user information is updated Note For the following cases an error message appears e The password and the retype password are different e The password character or character length is wrong 59 Operations continued Deleting the user Back End Administrator 20 39 51 Arbitrator 300 Bac str Update Users Groups Rules Classify Config 1 Select a user to be deleted on the User List Click on Delete A confirmation dialog box is displayed Click on Yes The confirmation dialog box is closed and the user will be deleted Cancel deleting Click on No in the confirmation dialog box 60 Importing users User information and group information are imported from
50. cccccssseeesesteeeeeeeeneeeeeeeenee 62 Adding groups eeeeeeeeeeeeeeeeeeeeeneeeeeeentaeeeeeeeaas 62 Displaying and editing the group information 63 Deleting a Group ici ss csscied nn n 63 Setting Evidence Rules 0 00 00 ccceeeeeeeeeeeeeeteeeeees 64 Adding a Mle sesccecietiveeneneenddaeiveee 65 Editing a Mle saarra ana 67 Deleting a Ule scccscssncnrnannnn 68 Setting Classify Information 69 Adding a classify tag ecccceeceeeeeeeettteeeeeeeee 69 Editing the classify information 69 Deleting the classify information cee 69 System Setup seeeeeeeeeeeeeeeeees 70 Drive Saing srera 71 Setting the Video INDOX essesessssiseeriseeissrsireesnse 71 Library Setting c eceeceeeeecceceeeeeeeeeeeeeeeeeeneees 71 Archive S ttinGisiesiisicaseasvecectisavsgsiataaiceaeedeeeaae ve 72 Unprocessed video Setting cceeeeeeeeees 73 LOG SOMING PEPA A 74 Operation log Setting ccccecceeeeceeteeteeessccees 74 Front End Application Recorder Log setting 75 Schedule Seting vescies ecient 76 Setting the time for processing 76 Setting the Case File Records Retention 76 Alert Seung accent eget aca aad 77 Setting the Password sseessssseesrreeeriserrrerrrreerinsars 78 Setting the password policy 78 Setting of password default eee 79 Setting the Database and Network 80 Setting the database i eeeeeeteeeeeeereeees 80 Confirming the streaming proxy settings
51. cel deleting Click on No in the confirmation dialog box 29 Updating the Back End Administrator and Back End Client applications On the Back End Update screen updating of the Back End Administrator application and Back End Client application is enabled Upper half of the screen is for a Back End Administrator application and the lower half is for a Back End Client application Click on the Back End Update tab The Back End Update screen appears Confirming the update status of the Back End Administrator and Back End Client applications On the Back End Update screen a list of PCs on which Back End Administrator or Back End Client application is running registered in the Back End Server is displayed On the list the version and date and time of last update of each Back End Administrator and Back End Client application are displayed In the Update Version field the latest version appears Updating the Back End Administrator or Back End Client applications Upon the start up of the Back End Administrator or Back End Client application the version of the application registered in the Back End Server is checked If the latest version is detected the Back End Administrator or Back End Client application is automatically updated The version of the updating software is displayed in the Update Version field Operations continued Registering the Back End Administrator or Back End Client application Only one vers
52. ck also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Setting of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while data was being written Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Setting of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Deletion of data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made The number of the VPUs registered with the BES exceeds the predetermined value An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct The number of registered recorder settings exceeds 100 Decrease the number of registered recorder settings then try again Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network
53. ck on the DB Network setting tab The DB Network setting screen appears Setting the database Arbitrator 300 Back End Administrator 2 0 39 51 Update Users Groups Rules Classify Config Setting the SQL server Setting for the database server to be connected will be made The database servers detected automatically will be displayed on the dropdown list Select the server on the list Setting the database The database managed by the database server will be displayed on the dropdown list Select the database on the list 80 Arbitrator 3 Update Rules Classify Config o From To Streaming is not available at present Upgrading is scheduled for the future Setting the System Name eee Set the System Name here Direct communication with the Back End Server and the Memory Card Video Recorder is enabled using the name set here System Setup continued Confirming the port settings Rules Classify Config Port settings for the items below will be displayed Back End Server Destination The port numbers for communication between the Back End Administrator application and Back End Server to process the request such as Login Video search etc are displayed in Connect to Back End Client Administrator TCP The port numbers to update the Back End Administrator module from the Back End Server are displayed in Update Back End Client Administrator TCP The port number to update the module f
54. connection is properly made Deletion of data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Updating of data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct 16010 No group name input No group name was input Input the group name Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 99 Error Messages continued Message Measure Failed to get the machine Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made Failed to get the group Acquisition of the information failed Verify with the administrator that the Information BES and DB have started Check also that the network connection is properly made Failed to get the free field Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made Too many registered data The number of registered VPU setting groups exceeded the predetermined
55. corder list are unchecked Delete button For deleting the Memory Card Video Recorder selected on the Recorder list Refresh button For updating the Recorder list Description of the Screen Displays continued Users Screen When the Users button on the main screen is clicked on the user registration screen is displayed On this screen registered users are listed Adding and deleting users and changing user information are enabled See Registering Users page 55 Arbitrator 360 Back End Administrati r 2 0 39 51 Update Users Groups Rules Classify Config Users List For displaying the User ID and name registered to the Back End Server Right clicking enables displaying the property and adding and deleting data Add button For adding users Add by AD button For adding users using the Active Directory data Property button For displaying the property screen for showing and editing the user data Delete button For deleting the users selected on the User list Import button For registering the user and group information stored on external media to the database Export button For exporting the user and group information registered in the Back End Server to external media 15 Description of the Screen Displays continued Groups Screen When the Groups button on the main screen is clicked on the group setting screen is displayed On this screen registered groups are listed A
56. cription of edit rule screen lt Rule Effects gt Permission Users Groups A list of users or groups registered in the database is displayed The listed users or groups have access permissions As default no user or group is stored Right clicking enables selecting all rights and clearing all rights Clear The users or groups selected on the Permission Users Groups list are cleared Add The Evidence Rule User AddForm screen is displayed View your own non Arbitrator video files acest htc cae ee ane l Clear All All groups or users on the Playback your own Arbitrator video files AV video Pera ae EAEE EA Permission Users Groups list are cleared Edit Bookmarks Classify Snapshots Reena meatus Store Days Enter the retention period of the C D Program Files PanasonicCV Contents Library video The default setting is 90 days Storage Location A list of storage locations is displayed As default no storage location is selected Right clicking enables selecting all storage locations and clearing all storage locations Rule N Ent l f a a near Help A Help file for the Rule screen is displayed Disable rule If checked the rule is disabled Permission Rights A list of the rights is lt Criteria gt displayed The Rights whose Allow check boxes are checked are enabled If the Deny check boxes are checked the corresponding Right to a file is disabled even if users or groups have the Rights
57. ct li E0240 Couldn t restore files e a E02471 Couldn t restore files E02481 Write error on slot4 Be sure to use the correct procedure to remove and load SDHC Memory Record cannot be continued Cards Replace an SDHC Memory Card that is not recognized after E02482 Write error on slot2 inserting it in the SDHC Memory Card slot and closing the SDHC Memory Record cannot be continued Card slot cover E02483 Write error on slot3 Record cannot be continued E02484 Write error on slot4 Record cannot be continued E07671 CAMERA1 communication error The Color Camera may not be correctly connected to the Memory Card Video Please check the CAMERA Recorder Check whether the camera cable included in the Color Camera is correctly connected to the Color Camera Contact your supplier if this measure does not solve the problem E08601 Playback and record cannotbe Close the SDHC Memory Card slot cover executed E08602 The recorder s fan has stopped Contact your supplier E10400 Radar model file was not found E10401 More than 10 radar model files were found E10402 Invalid radar model file was found E10403 Radar model file cannot be read E10410 Radar communication error Please check the radar setting E15751 VUP Card found on slot A card for upgrading is inserted Data cannot be written to the card Record cannot be started E15752 VUP Card found on slot2 Record cannot be started E15753 VUP Card found
58. ction Camera Camera connection can be set Camera1 ON The connection to the CAMERA 1 connector can be set Setting values ON OFF Camera2 ON The connection to the CAMERA 2 connector can be set Setting values ON OFF Camera3 OFF The connection to the CAMERA 3 connector can be set Setting values ON OFF Camera4 OFF The connection to the CAMERA 4 connector can be set Setting values ON OFF Camera5 OFF The connection to the CAMERA 5 connector can be set Setting values ON OFF Camera6 OFF The connection to the CAMERA 6 connector can be set Setting values ON OFF to be continued to the next page 1 If either the Main or Sub Resolution RecordRate is set to D1 10 the other is also set to D1 10 83 Setup continued Item Factory Preset Description Preset1 Preset 1 can be set Form 1 Channel The channel mode can be set Setting values 1Channel 2Channels 4Channels QUAD 4Channels PANORAMA 5Channels QUAD 5Channels PANORAMA None Pattern Main 1 Sub The combination of cameras displayed as Main and Sub videos can be set Setting values for Form and Pattern Pattern 1Channel Main 1 Sub Main 3 Sub 2Channels Main 1 Sub 2 Main 2 Sub 3 Main Sub 1456 Main Sub 2456 Main Sub 3456 4Channels PANORAMA Main Sub 1456 Main Sub 2456 Main Sub 3456 Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 5Chan
59. d 1 Select a Memory Card Video Recorder on Vehicle ID Vehicle IDs that belong to the group the Recorder Setting Update screen displayed in Group Name are listed 2 Click on Edit Group The Recorder Group screen is displayed 3 Select a Vehicle ID to be added to or deleted from the group To add a recorder to the group Select a Vehicle ID on the Vehicle ID and Group List then click on gt gt To delete a recorder from the group Select a Vehicle ID on the Vehicle ID list then click on lt lt Multiple Vehicle IDs can be selected 4 Click on OK A Group editing operation is finished and the Recorder Group screen is closed The edited group is registered in the database 36 Operations continued Deleting a group 1 Select a Memory Card Video Recorder with the Group to be deleted on the Recorder Setting Update screen Multiple recorders can be selected Click on Delete Group A confirmation dialog box is displayed Click on Yes The group to which the Memory Card Video Recorder selected in Step 1 belongs is deleted and the database is updated Cancel deleting Click on No in the confirmation dialog box 37 Operations continued Memory Card Video Recorder Configuration Setting Screen Note The default settings for various items are shown on the Setup list on pages 83 to 97 Admin Password screen Password For inputting an administrator password
60. days 53100 Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 53110 Failed to get the schedule Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made 53120 Failed to get the group Acquisition of the information failed Verify with the administrator that the Information BES and DB have started Check also that the network connection is properly made 53200 Failed to set the information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 53210 Failed to set the schedule Data writing failed Verify with the administrator that the BES and DB have information started Check also that the network connection is properly made Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 54010 Illegal setting range for the The specified retention period is outside the predetermined range retention period 54012 Illegal input contents for the The specified retention period data are incorrect retention period 54020 A value that is bigger than the The value specified a
61. dding and deleting groups and changing group information are enabled See Registering Groups page 62 Arbitrator 360 Back End Administrator 2 0 3 51 Update Users Groups Rules Classify Config Groups List For displaying the list of group name and group note registered in the Back End Server Right clicking enables displaying the property and adding and deleting groups Add button For adding groups Add by AD button For adding groups using the Active Directory data Property button For displaying the property screen for showing and editing the group data Delete button For deleting the groups selected on the Groups list Import button For registering the user and group information stored on external media to the database Export button For exporting the user and group information registered in the Back End Server to external media 16 Description of the Screen Displays continued Rules Screen When the Rules button on the main screen is clicked on the evidence rule setting screen is displayed On this screen rules are listed Adding and deleting rules and changing rules information are enabled See Setting Evidence Rules page 64 Arbitrator 360 Back End Administrator 2 0 39 51 Update Users Groups Rules Classify Config Rule Tree For displaying the rules registered in the Back End Server in tree format Right clicking enables adding editing or de
62. de 31030 31040 No group name input Failed to update the DB 31050 32000 Failed to update due to illegal data Please confirm the input information 32110 Fail to export 32120 Fail to set the group information 32140 Failed to write files 32210 Failed to import 32220 Failed to set the user information 32230 Failed to set the group information Failed to set the Group list information Failed to update due to illegal data Please confirm the input information Too many registered data 32240 40000 40002 40010 Failed to get the evidence rule information No group name was input Input the group name DB data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made This user has already existed An identical user name exists Specify a different user name An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Acquisition of user data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of group information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made File data writing failed Check 1 that there is sufficient free space on the destination medium 2 that the medium has be
63. deo files AV video Allow the user to export a copy fOmmanlcOnVeringneopy of AV video and burn into DVD video Export non Arbitrator video files Allow the user to export a copy file except AV videos Archive Arbitrator video files AV video Allow the user to move AV videos to archive area or to return them from archive area Archive non Arbitrator video files Allow the user to move files except AV videos to archive area or to return them from archive area Streaming and Convert Copy are not available at present Upgrading is scheduled for the future Operations continued Adding a user using Active Directory The user can be registered to the Back End Server by retrieving the user information from the Active Directory Information that can be retrieved from the Active Directory is as shown below e User ID e Full name of user e E mail address Notes e The password is retrieved from the Active Directory The user can be logged in with the Active Directory password When the user is logged in for the first time entering the password is requested e The rights shown below are enabled as default View your own non Arbitrator video files Playback your own Arbitrator video files AV video 350 Back End Administrator 20 48 51 Arbitrator Update Users Groups Rules Classify Config 1 Click on Add by AD The Active Directory screen i
64. e Memory Card Video Recorder Status The update status of the Memory Card Video Recorder e Wait for Update e Updating e Updated e Disconnected Select All button All Valid check boxes for the Memory Card Video Recorders shown on the Recorder list are checked Clear All button All Valid check boxes for the Memory Card Video Recorders shown on the Recorder list are unchecked Delete button For deleting the Memory Card Video Recorder selected on the Recorder list Refresh button For updating the Recorder list Description of the Screen Displays continued Recorder Setting Update screen When the Recorder Setting Update tab on the Update screen is clicked on the Recorder Setting Update screen appears The configuration settings of the Memory Card Video Recorder will be updated via LAN or WLAN See Updating the recorder settings page 33 Settings button Click to display the Recorder Setting screen Adding editing or deleting settings for the Memory Card Video Recorder is enabled Add Group button A new Memory Card Video Recorder group is created Edit Group button For editing the list of the Memory Card Video Recorders belonging to the group Delete Group button For deleting a Memory Card Video Recorder group Recorder list For displaying the list of the Memory Card Video Recorders detected by the Back End Server Right clicking enables deleting the firmware or refreshing the
65. e case file will be applied 22 Description of the Screen Displays continued Password setting screen When the Password setting tab on the Config screen is clicked on the password setting screen is displayed See Setting the Password page 78 Enable password policy For setting if password policy is used or not The use of password length For setting if restriction of character length for a password is used or not If checked the restriction shown below will be valid Minimum Minimum length Maximum Maximum length The use of both upper and lower case letters For setting the case sensitivity for a password When checked it is enabled Inclusion of one or more numerical digits For setting if the password should include numerical digits or not When checked a password should include numerical digits The use of password duration For setting the effective period of a password The password is requested to be changed at the end of the period set here When checked the password time limit is specified Empty or 0 means unlimited Enter the period in the box below When unchecked this restriction will not be applied Login settings For setting the login 23 Login to Back End using your operating system login When checked the login screen appears with the user name and password set as default if the user name being logged in Windows is registered in the Back End a
66. e of the maximum zoom magnification during automatic zooming seconds Setting values 3 5 8 Auto Zoom End 1 Automatic zooming end position setting Position Setting values 1 2 3 4 5 7 10 15 22 LAST Zoom Limit 220 Maximum magnification during zoom Setting values 22 220 AGC Level HIGH Automatic gain control setting for the color camera Setting values LOW MID HIGH OFF Flip OFF Vertical flipping of the output image from the color camera Setting values ON vertically flipped OFF No flipping Auto Focus PRESET The focusing method of the color camera in the following conditions can be set e When Init LPR Mode is set to DISABLE e When Init LPR Mode is set to ENABLE and LPR Mode is set to PATROL e When recording is started by a recording trigger signal with Init LPR Mode set to ENABLE and LPR Mode set to LPR Setting values PRESET When the zoom magnification is set to x3 or less the camera focuses on an object at about 15 m distance from the camera If zooming operation is performed afterward automatic focusing will be activated DISABLE The focal position is fixed at a distance of about 40 m and automatic focus is disabled AUTO Auto focusing when zooming magnification changes to be continued to the next page 1 The IR Level and IR Time settings are enabled only when Init IR Mode is set to AUTO 87 Setup continued Item Factory Preset Description Init Camera Settings a
67. e was found 6005 Invalid file path 6006 Illegal file 6007 Failed to get the PC information on network 6008 No rights to get the network path Unknown Server Error 117 Camera Connection and Combination of Cameras Combination of cameras depends on the cameras Selectable preset patterns depends on the detected connected to the recorder Available combination is as cameras shown below e If CAM1 is set to OFF any combination of cameras Selectable combination of cameras depends on the indicated by 1 cannot be selected e If CAMZ2 is set to OFF any combination of cameras indicated by 2 cannot be selected e If CAM3 is set to OFF any combination of cameras indicated by 3 cannot be selected If any of CAM4 CAMS or CAM6 is set to ON a pattern indicated by 456 can be selected detected cameras e If only CAM4 CAM5 and CAM6 are set to OFF preset patterns 4Ch Quad 4Ch Panorama 5Ch Quad and 5Ch Panorama cannot be selected If all of CAM1 CAM2 and CAM 3 are set to OFF preset patterns 4Ch Panorama and 5Ch Panorama cannot be selected e If two channels of CAM1 CAM2 and CAM 3 are not connected preset patterns 5Ch Panorama cannot be selected Camera Combination of cameras connection 2 3 456 ee ee i ry a pd Ea Ea es ps e es 1Ch 2Ch 4Ch 5Ch P Panorama B Preset number of recommended combination of cameras Selectable combination of camera
68. ected AG RCP30 was found to need an update The Remote Control Panel reboots automatically to start an update A Remote Control Panel not supported by the Memory Card Video Recorder was detected Disconnect the Remote Control Panel The vehicle engine switch is set to LOCK OFF when Power Off Time on page 50 is set to After Upload The system awaits that uploading is finished that the connection with the Back End application is released or uploading streaming administrator setup or upgrading on the Back End application is finished To continue using the Memory Card Video Recorder without turning it off set the engine switch to ON Wait until the error message is cleared Contact your supplier if the message does not clear after about a minute Insert another SDHC Memory Card 108 Error Messages continued Message Measure 02442 Write Protect cards found Disable SDHC Memory Card write protection Couldn t format E02444 No SDHC Cards found Insert an SDHC Memory Card Couldn t format E02460 System error tact ii Couldn t delete files Contact your s pplier E02461 Couldn t delete files Check the card information and proceed as follows according to the information CARD PROTECT Disable SDHC Memory Card write protection UNFORMATTED Replace with the formatted SDHC Memory Card NO CARD Insert an SDHC Memory Card Others Replace the SDHC Memory Card with another one System error Conta
69. ed System Setup continued Alert Setting Arbitrator 300 Back End Administrator 2 0 39 51 Update Use Groups Rules Classify Contig If videos are not uploaded exceeding the specified days the alert e mail is sent to the specified group Setting the period Enter the days in the days field Default 7days Setting the destination of the e mail Specify the group to which the alert e mail is sent to in the Send to field Select a group registered in the database from the dropdown list Notes e To use this function Mailer must be installed in advance e Receiving the alert e mail depends on the network environment Consult your network administrator e The alert e mail is sent for each Memory Card Video Recorder If the alert e mail is not required for a recorder delete the recorder by selecting it then clicking on the Delete button on the Recorder Update screen See Deleting the recorder page 32 77 System Setup continued Setting the Password Set the password policy Click on the Password setting tab The Password setting screen appears Setting the password policy Set the password policy used for the user password Selecting the use of the password policy Check the Enable password policy check box and the all password policy will be used If not checked all password policy will not be used Setting of the password length If the The use of password length chec
70. egistered to the Memory Card Video Recorder Setting values Administrator Agency Unit Shift Area VehiclelD Allow Guest Login OFF Select if login of a user who has not been registered in the Back End Server or the Memory Card Video Recorder is permitted or not Setting values ON OFF Login using your OFF Select whether the login screen with the password entered will be current login account in displayed upon startup the operating system Setting values ON OFF Clear User OFF Select if the user information of the Memory Card Video Recorder is Information on deleted upon logoff Recorder when logout Setting values ON OFF Disable Operation for OFF Set the operation prohibited by a user Setting values STOP OFF Simple Operation Mode Only OFF Select if only Simple Operation mode screen is permitted by a user or not Setting values ON OFF EXpon DVD burn Operation DISABLE Set if DVD burn is enabled by a user Setting values ENABLE DISABLE 1 Setting values of Meta Definitions can be changed when installing the Back End Server Exporting from the Front End application is not available at present Upgrading is scheduled for the future 96 Setup continued Triggers The trigger signals GP11 16 can be set Item Factory Preset Description Trigger ON Set if the GPI trigger function is used or not Setting values ON OFF Name
71. en properly inserted 3 if the medium is write protected and 4 that writing to the destination medium is authorized Importing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Importing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Importing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Importing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct The number of registered evidence rules exceeds 100 Decrease the number of registered evidence rules then try again Acquisition of the list of evidence rules failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 101 Error Messages continued 40020 Fail to get the group information Failed to get the free field information Fail to delete the Evidence rules Failed to add the Evidence rules Failed to edit the Evidence rules 40130 40140 Fail to update the Evidence rule Rule name has already existed 41000 Failed to update due to illegal data Please confirm
72. er 60330 This folder cannot be used The As the specified file path is too long this folder cannot be used Specify a file specified file path is too long The path within 200 characters file path that can be specified is within 200 characters Disconnected to the recorder Improper module structure Please reinstall Invalid officer1 ID Please input The Officer 1 ID is invalid registered ID e Check that Officer 1 has been registered in the Back End System e Check that Officer 1 has been registered in the recorder e Set Guest mode to ON in Administrator Setup Invalid officer2 ID Please input The Officer 2 ID is invalid registered ID e Check that Officer 2 has been registered in the Back End System e Check that Officer 2 has been registered in the recorder e Set Guest mode to ON in Administrator Setup The officer1ID and the officer2 The IDs for Officers 1 and 2 are identical ID are the same Please input e Use different IDs different IDs The password is wrong The input password is invalid e Input a valid password 105 Error Messages continued Cannot set the same preset Set different preset Invalid Camera connection Connect two or more cameras or either from camera to camera3 When presets is set it is not possible to set None in preset2 The retyped password is different Please input again An invalid character is included Please input again Length of folder name is up to
73. er is not possible 51240 The folder cannot be deleted any Not all folders can be deleted At least one folder must be registered further This folder cannot be used The root directory cannot be specified Specify a different folder 51260 This folder cannot be used The __ This folder cannot be used because the specified file path is too long specified file path is too long The Specify the file path within 200 characters file path that can be specified is within 200 characters Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input _ etc Make sure that the input data are correct information The log retention period is too The specified preservation duration exceeds the limit Specify within the long The maximum terms that predetermined range can be set are 4000 days The capacity limitation size of the The minimum size for the archive area is too great Specify a smaller value log is too large The maximum capacity that can be set is 1000MB 52100 Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Failed to get the drive information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made
74. ern for Preset 1 Preset 2 and Preset 3 See Camera Connection and Combination of Cameras on page 118 Form Set the channel mode Pattern Set the camera connection pattern Setting values for Form and Pattern 1Channel Main 1 Sub Main 3 Sub M S ain 2 Su 2Channels Main 1 Sub 2 Main 2 Sub 3 a T ain 1 4Channels QUAD b b3 4Channels PANORAMA INONE ooo o 1 This setting is enabled when the camera connected to the CAMERA 1 connector is set to OFF 2 None is not selectable for Preset1 unless all camera connections are set to OFF 5Channels PANORAMA i in Main Sub 1456 in 40 Select the type of microphones connected to each of AUDIO IN 1 2 3 and 4 connectors on the Memory Card Video Recorder or turn the microphone off Setting values Mic Wireless Mic Off Init Audio Rec after power ON hit Audio Rec after power ON Oon oOrFF IE Set the audio recording status upon startup of the Memory Card Video Recorder The setting will be applied to all four audio channels Setting values ON OFF LAST Operations continued Camera screen Camera Perform the settings for the color camera that is connected to the CAMERA 1 connector on the Memory Card Video Recorder Mosse Bauto IR Level Set the IR level for automatic switching of the IR function Setting values LOW HIGH IR Time s Set the detection
75. es 12 Recorder Update screen ceeeeeeeees 13 Recorder Setting Update screen 14 USEIS SChOCM so nan nO R 15 Groups Screen cccecccceceeeeeeeeeeneecaeceeeeeeeeeeeteees 16 Rules SCreen ssssjesscerstiaas ea aasstevsrngeenadveaaiedeasvaeen 17 Classify Screen cccccceceeeeeeeeeeeeeeeeeeeeeteeeeeeeenanees 18 Configuration Sereen essenonscniorscnrann r 19 Drive setting SCreen useneeiriisrrriirreeiie 20 Log setting SCIOGN aeren nenns E 21 Schedule setting screen cnereeniinas 22 Password setting Screen seeeeeeeeeeeeeeeee 23 DB Network setting screen 24 Startup and Termination 26 Staring UP esien a E 26 Terminating cceeeececeeeceecaeceeeeeeeeeeeseeecncaeeaeeeeeees 27 Operations mo an a ers 28 Uyole ria PONE E E E E E E 28 Updating the Front End application 28 Updating the Back End Administrator and Back End Client applications 0 c0e 29 Updating the firmware of the Memory Card Video Recorda esscr a nia 31 Updating the recorder settings eeee 33 Memory Card Video Recorder Configuration DEMING SCEE ities eaters v esti 38 Registering USCIS cccceeeceeeeeeeeteeeeeeenteeeeeeeaes 55 Adding the USEF ernir 55 Displaying and editing the user information 59 Deleting the USED c ccceeseccceeeececcseeteeteceeeees 60 importing USE S onnanoasankanmsn ennaa 60 EXPOmlNG USCIS nannan a a 61 Registering Group ccc
76. ft Upper Right Bottom Left Bottom Right 47 Time Select if time is displayed as an Embedded OSD Setting values ON OFF Trigger Select if trigger indications are to be displayed as Embedded OSD Setting values ON OFF VehiclelD Area Select if the vehicle ID and area are to be displayed as Embedded OSD Setting values ON OFF Operations continued Radar GPS screen Radar GPS Connection of GPS Select if the GPS is connected to the Memory Card Video Recorder or not Connection of Radar Setting values Recorder OFF Select if a radar gun is connected to the Memory Card Video Recorder or not Collection Time s Setting values Recorder OFF Select an interval of collecting data from the GPS Setting values 1 2 5 10 seconds Model Select Select the model name of the connected radar gun Rec Start Information from the drop down list Setting values ProLaser3 STALKER_DUAL GOLDEN_EAGLE II Register Radar button For registering the radar gun library to the Memory Card Video Recorder Speed Unit Select the speed unit Setting values MPH km h 48 Operations continued Rec Play screen PreRec Time Video s Select the pre recording time for video Setting values 0 10 20 30 60 90 seconds PostRec Time Video s Select the post recording time for video Setting values 0 10 20 30 60 90 seconds PreRec Time Audi
77. fter power ON The initial settings upon startup of the color camera connected to the CAMERA 1 connector on the Memory Card Video Recorder can be set Init Backlight OFF Initial setting of backlight compensation Setting values ON OFF LAST The backlight compensation is enabled when set to ON Init IR Mode AUTO Infrared imaging function switching Setting values ON The IR function is forcibly set to ON OFF The IR function is forcibly set to OFF AUTO The IR function is automatically turned ON or OFF LAST Init Camera 1 LED ON Initial setting of the REC lamp of the color camera Setting values ON The lamp is lit during recording OFF The lamp does not light LAST Init AE Shift 0 Initial setting of the brightness for the color camera Setting values 2 1 0 1 2 LAST Init LPR Mode DISABLE License Plate Recognition function switching Setting values ENABLE LPR function enabled DISABLE LPR function disabled LPR Mode is switched to PATROL 1 The setting upon the last power off will be restored when the camera is turned on If the Memory Card Video Recorder is not turned off properly the setting data upon power off may not be stored properly 2 When Init AE Shift is set to 2 and the subject is dark the number of frames to be updated per second may become less than 30 88 Setup continued Date Time The date and time can be set Item Fac
78. gistering users who are enabled to use the Back End Administrator application Back End Client application and Front End application See Users Screen page 15 Groups button For displaying the group registration screen for grouping users See Groups Screen page 16 Rules button For displaying the evidence rules setting screen for defining evidence rules applied to the video files registered in the database See Rules Screen page 17 Rules Classify Config Classify button For displaying the classify setting screen for defining a classify tag See Classify Screen page 18 Config button For displaying the configuration screen for setting the Back End Server See Configuration Screen page 19 Help button When this button is clicked the mouse pointer will be turned to Clicking on a button or input field with this pointer will display the description of the clicked button input field Note If you use Adobe Reader 8 or 9 the description may not be displayed correctly when you click on a button or input field Description of the Screen Displays continued Update Screen When the Update button on the main screen is clicked on the remote update screen for updating the Front End application Back End application firmware of the Memory Card Video Recorder and recorder settings is displayed Arbitratcr 360 Back E d Administrator 2 1 39 51
79. he gt gt button Then the selected tags move to the Belong list on the right If you click on OK and the tags will be listed on the Classify Tags list Delete button Click to delete classify tags selected on the Classify Tags List GPO GPO1 Signal GPO2 Signal GPO3 Signal Select if the recording and recording error statuses are output to GPO 1 2 and 3 Setting values GPO1 Signal GPO2 Signal OFF REC ERROR REC ERROR GPO3 Signal OFF REC Note The functions of GPO1 GPO2 and GPO3 can be changed with settings GPO4 always outputs the power status of the recorder and has no setting 50 Operations continued Init Settings after power ON hit Settings after power ON hit Preset Select Preset a hit Video Outl Video Out2 Ea Init Preset Select Select a preset applied when the Memory Card Video Recorder is turned on Setting values Preset1 Preset2 Preset3 LAST Init Video Out1 Select a signal to be output from the VIDEO OUT 1 connector of the Memory Card Video Recorder when it is turned on Setting values CAM1 CAM3 Video Out2 LAST 51 Storage Capacity Warning 1g Wai Remaining Recordable Time min A warning sounds when the remaining recordable time becomes shorter than the value set here Setting values 30 60 90 minutes Warning sound Select if a short beep is to sound twice every 30 seconds when the remaining recordable
80. he Update screen is clicked on the Recorder Update screen appears The firmware of the Memory Card Video Recorder is updated by transferring the latest version from the Back End Server directly or via the Front End application to the recorder using LAN or WLAN See Updating the firmware of the Memory Card Video Recorder page 31 Update Version display For displaying the software version for updating Register button For registering the firmware for the Memory Card Video Recorder in the Back End Server Recorder list For displaying the list of the Memory Card Video Recorders detected by the Back End Server Right clicking enables deleting the firmware or refreshing the screen Valid Check the check box and the corresponding firmware will be updated VehiclelD The Vehicle ID If the Valid check box is unchecked single clicking enables editing Last Update Date Time The last applying date and time of the firmware of the Memory Card Video Recorder Recorder Version The current version of the firmware of the Memory Card Video Recorder Model The model name of the Memory Card Video Recorder available on the AG CPD20P only Serial The serial number of the Memory Card Video Recorder available on the AG CPD20P only MAC Address The MAC address of the Memory Card Video Recorder s network interface for connecting with the Front End application IP Address The IP address of th
81. ime No IP address is set as default Alert Streaming If a check mark is placed in the box when streaming is in progress in the Back End Administrator application that is indicates on the Front End application screen This function is enabled as default Streaming is not available at present Upgrading is scheduled for the future Recorder PC LAN acorder PC annection from Rec ont DHCP IP Address Subnet Mask DHCP Set if the LAN port on the Memory Card Video Recorder that is used for connecting to the Front End application is to operate as a DHCP server or not Setting values OFF Server1 Server2 Server3 Server4 45 IP Address Set the IP address for the LAN port on the Memory Card Video Recorder that is used for connecting to the Front End application This setting is enabled when DHCP is set to OFF Subnet Mask Set the subnet mask for the LAN port on the Memory Card Video Recorder that is used for connecting to the Front End application This setting is enabled when DHCP is set to OFF Gateway Set the default gateway for the LAN port on the Memory Card Video Recorder that is used for connecting to the Front End application This setting is enabled when DHCP is set to OFF Recorder UPLOAD LAN Rec rder UPLOAD LAN Wit DHCP The settings for the wired LAN port on the Memory Card Video Recorder that is used for connecting to the Back End Server can be performed D
82. indows XP 1 Click on the Start button 2 Select Control Panel 3 Double click on Add or Remove Programs The Currently installed programs window opens 4 Select the program to be uninstalled 5 Click on the Remove button A confirmation message appears 6 Click on the Yes button Uninstalling of the selected program starts Procedures for Windows Vista Click on the Start button N Select Control Panel 2 gt Double click on Programs and Features The Uninstall or change a program window opens D Select the program to be uninstalled 5 Click on Uninstall The User Account Control window opens 6 Click on the Continue button The Uninstall window opens 7 Click on the Uninstall button Uninstalling of the selected program starts Description of the Screen Displays Main Screen When the login succeeds the main screen appears The main screen contains a toolbar and setting section Arbitrator 860 Back End Administrator 2 0 29 51 Toolbar L Update l Users Groups Setting section Toolbar When one of the buttons is clicked on the screen for the corresponding function will open Update Users Groups Rules Classify Config Update button For displaying the remote update screen for updating software and the settings of the Memory Card Video Recorder See Update Screen page 10 Users button For displaying the user registration screen for re
83. ing on the Action setting e In a case of REC Preset1 Rec Preset2 Rec or Preset3 Rec Setting values High High edge trigger Level High High level trigger Low Low edge trigger Level Low Low level trigger Both Both edge trigger e Ina case of Preset1 Preset2 Preset3 CAM1LED AUTOZOOM AUDIO2ON or STOP Setting values High High edge trigger Low Low edge trigger Both Both edge trigger In a case of TGT REC TGT P1REC TGT P2REC TGT P3REC OWN REC OWN P1REC OWN P2REC or OWN P3REC Setting values OFF 1 2 200 e In a case of NONE Setting values High High edge trigger Low Low edge trigger Display OFF Character definition when one character is displayed as an OSD Setting values A Z OFF 4 These cannot be selected if Preset2 or Preset3 is 2 These cannot be selected if Audio2 on the Allocation not specified on the Allocation Video Audio screen Video Audio screen is set to OFF 3 Selectable only for Trigger15 and 16 97 Error Messages Messages for the Back End Administrator Application 90000 Failed to update due to illegal data Please confirm the input information Please wait Accessing DB in process No rights to update remotely 90010 90100 Message Measure An error was generated while updating screen data because of illegal data etc The program cannot be exited because the DB is being accessed Please wait The remote update operati
84. ion of the Back End Administrator and Back End Client applications can be registered in the Back End Server When a new version is registered the old one will be deleted 1 Click on Register The file selection dialog box appears 2 Select the update module for the Back End Administrator or Back End Client application 3 Click on Open The update module is checked if it is correct The application is registered if the module is correct If it is not correct an error message appears Updating the Back End Update screen Click on Refresh The screen will be updated 30 Deleting PC on which Back End Administrator or Back End Client application is running 350 Back End Ade 1 Select PCs to be deleted on the Back End Administrator or Back End Client application list 2 Click on Delete A confirmation dialog box is displayed 3 Click on Yes The selected PCs will be deleted from the list Cancel deleting Click on No in the confirmation dialog box Operations continued Updating the firmware of the Memory Card Video Recorder The firmware of the Memory Card Video Recorder is updated via wired or wireless LAN Click on the Recorder Update tab The Recorder Update screen appears 0 a Rules Classify Config Back End Administrator 2 0 9 T Users Groups Mbitrator 30 Update Confirming the update status of the recorder On the Recorder Update screen a list
85. is displayed GteuP AE REP eg Note Enter note of the group 2 Enter the group information Right List Check the rights to be given to the group Right clicking enables checking or unchecking all rights View your own non Arbitrator video files and Playback your own Arbitrator video files AV video are checked as default See Right list page 57 Select All All rights are checked S video without any officer ID iny officer ID Clear All All rights are unchecked out ar Playback your own Arbitrator video files AV video C Playback all Arbitrator video files AV video Edit Bookmarks Classify Snapshots AV vi ae All Other Users A list of users registered in the fs Back End Server is displayed in ascending order Right clicking enables the same function as clicking on Group s Users A list of users in the group is 3 Set the rights displayed in ascending order Right clicking Check the rights to be given to the group on the enables the same function as clicking on Right List To select all rights on the Right List Click on Select All To release all rights on the Right List Click on Clear All 62 Operations continued Displaying and editing the group Deleting a Group information Arbitrator 360 Back End Administrator 2 113051 Update Users Groups Rules Classify Config Arbitrator 3607 Back End Administrator 2 0 30 51
86. ith the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while data was being written Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while data was being written Verify with the administrator that the BES and DB have started Check also that the network connection is properly made The application file to be registered does not exist This error is not generated in normal situations The version data of the application file to be registered cannot be obtained Check that the correct application file is specified The application file to be registered is improper Check that the correct application file is specified 98 Error Messages continued 11430 This version has already been registered You have not selected a valid update file Please do this first Too many registered data 11500 11600 14000 Failed to update due to illegal data Please confirm the input information Message Measure The updater module is of the same version as that already registered with the BES and cannot be registered The application file to be registered is improper Check that the correct application file is specified The number of FEs or VPUs registered with the BES exceeds the predetermined value An error was generated while updating screen data beca
87. k box is checked settings shown below will be enabled If not checked the setting is disabled Minimum Enter the minimum length of password in the Minimum field Maximum Enter the maximum length of password in the Maximum field Setting of case sensitivity When the The use of both upper and lower case letters check box is checked both upper and lower case letters should be included in the password If not checked the password including either upper case or lower case only is enabled 78 Setting the use of numerical digits Set if the password includes numerical digits or not If the Inclusion of one or more numerical digits check box is checked the password should include one or more numerical digits If not checked this restriction will not be applied Setting the password duration Enter the password duration in days field If the The use of password duration check box is checked the password must be changed every this duration If not checked this restriction will not be applied System Setup continued Setting of password default Rules Classify Config When the Login to Back End using your operating system login check box is checked the login screen appears with user name and password entered if the user logged in is registered to the Back End application 79 System Setup continued Setting the Database and Network The database and network settings can be made Cli
88. l An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 18020 Failed to download File downloading failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 20000 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 20002 Too many registered data The number of registered users exceeds 40 000 Decrease the number of registered users then try again 20010 Failed to get the user information Acquisition of user data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 20020 Failed to delete the user data Deletion of user data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 21000 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 21010 Failed to get the group Acquisition of group information failed Verify with the administrator that Information the BES and DB have started Check also that the network connection is p
89. led for the future System Name SS S For communicating the Back End Server with the Memory Card Video Recorder directly The communication is enabled only with the recorder having the system name set here 24 Description of the Screen Displays continued IP Address Setting For setting the IP address Front End IP Address For displaying the IP address for communicating with the Memory Card Video Recorder via the Front End application Recorder IP Address For displaying the IP address of the Memory Card Video Recorder for communicating with the Memory Card Video Recorder Add button When this button is clicked on the IP Address Setting dialog box appears IP addresses can be added Delete button For deleting the IP address selected on the IP address list 25 Startup and Termination Starting up 1 Turn on the PC 2 Double click on the Back End Administrator icon on the desktop The Login screen is displayed Arbitrator 360 Back End Administrator 20 39 51 a K Arbitrator v 192 168 30 200 3 Enter the IP address or Host name of the Back End Server in the Back End Server field If you have logged in before you can select it from the dropdown list 4 Enter the User ID If you have logged in before you can select the User ID from the dropdown list 5 Enter the password 6 Click on Login The Main screen is displayed Canceling login Click on
90. leting the rules or opening or closing all rules Add button When this button is clicked on the Rule screen appears on which rules can be added Edit button When this button is clicked on the Rule screen appears on which rules can be edited Delete button For deleting rules Apply button For registering the edited rules in the database Cancel button For canceling editing of the rules 17 Description of the Screen Displays continued Classify Screen When the Classify button on the main screen is clicked on the classify setting screen is displayed On this screen classify tags are listed Creating deleting and changing classify tags are enabled See Setting Classify Information page 69 Arbitrator 360 Back End Administrator 2 0 39 5 Update Users Groups Rules Classify Config Classify List For displaying the list of the Classify tag registered in the database Right clicking enables adding editing and deleting Classify tag Double clicking enables editing the Classify tag Add button For displaying the Input Classify Tag screen for adding a classify tag Edit button For displaying the Input Classify Tag screen for editing a classify tag Delete button For deleting the Classify Tags 18 Description of the Screen Displays continued Configuration Screen When the Config button on the main screen is clicked on the system configuration screen is displa
91. mera 2 This setting is enabled when the camera connected to the CAMERA 1 connector is set to OFF 85 Setup continued Item Factory Preset Description Preset3 Preset 3 can be set Form 2 Channels The channel mode can be set Setting values 1Channel 2Channels 4Channels QUAD 4Channels PANORAMA 5Channels QUAD 5Channels PANORAMA None Pattern Main 1 Sub 2 The combination of cameras displayed as Main and Sub videos can be set Setting values for Form and Pattern Pattern 1Channel Main 1 Sub Main 2 Sub Main 3 Sub 2Channels Main 1 Sub 2 Main 1 Sub 3 Main 2 Sub 3 4Channels QUAD Main Sub 1456 Main Sub 2456 Main Sub 3456 4Channels PANORAMA Main Sub 1456 in Sub 2456 Main Sub 3456 Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 5Channels PANORAMA Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 Audio In Select The audio inputs can be selected Audio1 Wireless Mic The audio signal connected to the AUDIO IN 1 connector can be selected Setting value Mic microphone Wireless Mic wireless microphone Off no connection Audio2 Mic The audio signal connected to the AUDIO IN 2 connector can be selected Setting value Mic microphone Wireless Mic wireless microphone Off no connection Audio3 OFF The audio signal connected to the AUDIO IN 3 connector can be selected Setting val
92. n Browse The Server Folder Setting dialog box appears 2 Select a folder 3 Click on OK The full folder path is displayed in the Root Path of Front End Recorder field Setting the capacity for a log file Enter the maximum capacity for a log file in the Capacity restrictions field When the capacity exceeds the value set here the error log is deleted from the oldest one 75 System Setup continued Schedule Setting Setting for scheduling of batch processing executed at the specified time is made Click on the Schedule setting tab The Schedule setting screen appears At the specified time the processing shown below will be executed e Deleting the videos exceeding the retention period e Reapplying the changes of Storage Location setting in the Evidence Rule e Checking the Memory Card Video Recorder which does not upload videos Setting the time for processing Setting the Work Start Time to process Enter the start time of the batch processing in the Work Start Time field Default 00 00 Setting the Work Time to process Select the work time from the dropdown list Setting value 1hour 2hour 3hour 5hour Until End Default 2hour If the processing is not completed in Work Time it will continue next day 76 Setting the Case File Records Retention asi s Rules Classify Config When checked the longest retention period of the files associated to the same case file is appli
93. n Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 60140 Can t assign the read only folder A read only folder cannot be registered 60150 Can t assign the offline folder An off line folder cannot be registered 60160 Can t assign the system folder A system folder cannot be registered 60170 Can t assign the folder which The following special folders which the OS uses cannot be registered belongs to this folder System folders Desktop folders Shared program files Cookies Logs Internet cache Program files Document template Startup Recently accessed documents Startup menu 60180 Can t assign the private folder A private folder cannot be registered 60200 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 60300 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information 60310 A minimum free space is too The minimum size for the archive area is too great Specify a smaller value large The maximum value that can be set is 1000GB 60320 This folder cannot be used The root directory cannot be specified Specify a different fold
94. n the files are registered in the database Click on Rules The Rules screen is displayed 29 51 Rules Classify i Config Criteria The meta information of the file is used as Criteria Classify Officer 1 Officer 2 Field1 Field2 Field3 Field4 Field5 Vehicle ID and Bookmark Note are specified as Criteria Effect Access permission retention period and the storage locations are specified as Effects Access permission determines whether or not the group may access the file and its rights The storage locations are selected from among the locations displayed on the screen The retention period is determined by the evidence rules separated files and case files The longest period of the three conditions listed below will be the retention period 1 When one file is applied to multiple rules but with different retention period set the longest retention period will be applied to the file 2 When a file is a part of the separated files the longest period among the separated files will be applied 3 The longest period among the files associated with the case file is applied This function is enabled or disabled in System setup of the Back End Administrator application Access permission is determined by the evidence rules user rights and group rights If the rights have not been set with the evidence rules the rights set with the User setting or Group setting are enabled The Rights that are set to be denied
95. nels PANORAMA Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 to be continued to the next page 1 Selectable Form and Pattern of Preset1 Preset2 3 None is not selectable for Preset1 unless all and Preset3 depend on the settings of Connection camera connections are set to OFF Camera 2 This setting is enabled when the camera connected to the CAMERA 1 connector is set to OFF 84 Setup continued Item Factory Preset Description Preset2 Preset 2 can be set Form 1 Channel The channel mode can be set Setting values 1Channel 2Channels 4Channels QUAD 4Channels PANORAMA 5Channels QUAD 5Channels PANORAMA None Pattern Main 2 Sub The combination of cameras displayed as Main and Sub videos can be set Setting values for Form and Pattern Pattern 1Channel Main 1 Sub Main 3 Sub 2Channels Main 1 Sub 2 Main 2 Sub 3 Main Sub 1456 Main Sub 2456 Main Sub 3456 4Channels PANORAMA Main Sub 1456 Main Sub 2456 Main Sub 3456 5Channels QUAD Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 5Channels PANORAMA Main 1 Sub 2456 Main 1 Sub 3456 Main 2 Sub 3456 Main 3 Sub 2456 to be continued to the next page 1 Selectable Form and Pattern of Preset1 Preset2 3 None is not selectable for Preset1 unless all and Preset3 depend on the settings of Connection camera connections are set to OFF Ca
96. o s Select the pre recording time for audio Setting values 0 3 10 20 30 60 90 seconds PostRec Time Audio s Select the post recording time for audio Setting values 0 3 10 20 30 60 90 seconds Rec Continue Time min Select the recording duration Setting values Continue 1 2 5 10 15 20 30 60 90 minutes 49 Intermittent Rec Select if the intermittent recording mode is enabled or not Setting values ON OFF Loop Rec Select if the loop recording mode is enabled or not Setting values ON OFF Rule of Filename Select the time system to be used in the video filename that is recorded on the Memory Card Video Recorder Setting values World Time Local Time Power On Rec Select if recording is started when the Memory Card Video Recorder is turned on Setting values ON OFF Record sound Select if a beep sounds every minute during recording Setting values ON OFF Operations continued APPLICATION AND LAPTOP Action Specified Timeout s 20 E Power Off Time min Select the time required from the ACC is turned off up to the Memory Card Video Recorder is turned off Setting values 0 10 20 30 60 90 120 180 minutes After Upload Apply To When Power Off Time is set to After Upload select which one s uploading is to be observed Setting values APPLICATION ONLY LAPTOP ONLY APPLICATION AND LAPTOP Note This setting is en
97. o register the file information oj N 109 The file information has existed 110 Failed to register the officer Failed to modify the file information No file information exists Failed to modify the video information Failed to modify the officer information 119 No bookmark exists No Officer information exists Failed to modify the event information No event information exists 120 121 122 123 124 125 126 114 Error Messages continued a E T 127 Failed to modify the GPIO information 128 No GPIO information exists 129 Failed to transfer the file 130 Failed to create the file path on the server or no path exists 131 The file has existed 132 Failed to create the file on the server 133 No file exists 134 Failed to modify the right 135 Failed to delete the actual data 136 The registration number of attached file is exceeded 137 Invalid video 138 Locked 139 No lock by your own 140 Failed to add the drive 141 Failed to add the case file 142 Failed to set to link the contents 143 Failed to modify the drive 144 Failed to modify the case file 145 Failed to do multiple operation 146 No rights to modify the evidence rule 147 Failed to add the evidence rule 148 Failed to search the evidence rule 149 Illegal contents information 150 Failed to delete the evidence rule 151 Failed to update the contents information by the evidence rule 152 Locked the contents
98. on each screen are canceled 70 System Setup continued Drive Setting Library setting Set folders in which videos are to be registered Click Te Rules Cias PE on the Drive setting tab The Drive setting screen appears Setting the Video Inbox Set a folder in which video files are to be stored Multiple folders can be set Adding a folder 1 Click on Add The Register folder dialog box appears Set the Video Inbox in which video files are temporarily stored until the files are registered in the database The full folder path for Video Inbox is displayed in the Video Inbox field Changing the folder 2 Click on Browse 1 Click on Browse The Server Folder Setting dialog box appears The Server Folder Setting dialog box appears 3 Select the folder 2 Select the folder If the specified path requires the user name and password on the network drive the user name If the specified path requires the user name and password input dialog box appears password on the network drive the user name password input dialog box appears Register folder x Register folder x a aa Enter the user name and password then click on Enter the user name and password then click on OK OK 4 Click on OK 3 Click on OK to close the dialog box The full folder path is displayed in the Folder Path The full folder path for Video Inbox is displayed in nela the Video Inbox field 5 Enter the req
99. on is not authorized Obtain remote update authority with BEA 90200 No rights to set users 90300 No rights to set groups 90400 No right to set rules 90500 No rights to set classify 90600 No rights to change configuration 9010 A fatal error occurred It will end the application 9020 This application already started 10000 Failed to update due to illegal data Please confirm the input information Failed to update due to illegal data Please confirm the input information Failed to get the information 11000 11100 Failed to get the software release information Failed to get the machine information Failed to get the installation information Fail to get the free field information Failed to get the free field information Failed to set the information Failed to set the installation information Failed to delete the machine information No Upload Application file was found Failed to get the file version information of upload application This is not a valid update file Please select a valid file User operation is not authorized Obtain user authority for the user or group with BEA The group operation is not authorized Obtain group authority for the user or group with BEA Rule setting is not authorized Obtain rule setting authority for the user or group with BEA Classify setting is not authorized Obtain classify setting authority for the user or group with BEA
100. on of OFF Device to which a radar gun is connected Radar Setting values Recorder Off Model Select ProLaser3 Model selection of the radar gun Setting values ProLaser3 STALKER_DUAL GOLDEN_EAGLE II GPS GPS related settings Connection of GPS Recorder Device to which the GPS is connected Setting values Recorder OFF Collection Time s Intervals of GPS data collection seconds Setting values 1 2 5 10 Rec Start Information Speed Unit MPH Unit of the speed of your vehicle Setting values MPH mile h km h 1 To use a radar gun consult your supplier 93 Setup continued Rec Play The settings related with recording and playback can be performed Item Factory Preset Description Rec Recording related settings PreRec Time 30 Video prerecording time seconds Video s Setting values 0 10 20 30 60 90 PostRec Time 0 Video post recording time seconds Video s Setting values 0 10 20 30 60 90 PreRec Time 0 Audio prerecording time seconds Audio s Setting values 0 3 10 20 30 60 90 PostRec Time 0 Audio postrecording time seconds Audio s Setting values 0 3 10 20 30 60 90 Rec Continue Time Continue Recording duration minutes min Setting values Continue 1 2 5 10 15 20 30 60 90 Intermittent Rec OFF Intermittent recording Setting values ON OFF Loop Rec OFF Loop recording
101. on slot3 Record cannot be started E15754 VUP Card found on slot4 Record cannot be started E15755 Unsupported Card found on slot1 The inserted card cannot be used Check card type Record cannot be started E15756 Unsupported Card found on slot2 Record cannot be started E15757 Unsupported Card found on slots Record cannot be started E15758 Unsupported Card found on slot4 Record cannot be started 109 Error Messages continued No Message Measure E15759 Unformatted Card found on slot1 An unformatted SDHC Memory Card has been inserted Record cannot be started Format the SDHC Memory Card using the Memory Card Video Recorder E15760 Unformatted Card found on slot2 or SD Memory Card Formatting Software or replace it with a formatted Record cannot be started SDHC Memory Card You can download the SD Memory Card Formatting E15761 Unformatted Card found on slot3 Software from the Website shown below Record cannot be started http panasonic jp support global cs sd download sd_formatter html E15762 Unformatted Card found on slot4 Record cannot be started E15763 Write Protect Card found on slot1 The write protect switch of the SDHC Memory Card is set to LOCK Slide Record cannot be started the write protection switch away from the LOCK position E15764 Write Protect Card found on slot2 Record cannot be started E15765 Write Protect Card found on slot3 Record canno
102. onnection is properly made This user has already existed A user with the same user ID exists Change the user ID An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Data acquisition from the active directory server failed Check also that the network connection is properly made An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct The number of registered groups exceeds 1 000 Decrease the number of registered groups then try again Acquisition of the group list failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Deletion of group information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made An error was generated while updating screen data because of illegal data etc Make sure that the input data are correct Acquisition of group information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of user data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly ma
103. or an administrator from the Back End Server is displayed in Update from Front End TCP Streaming is not available at present Upgrading is scheduled for the future 81 System Setup continued Setting the IP address 5 Rules Classify Config rhitrator 360 Back End Administrator 2 Update Users Groups The IP address for communicating with the Memory Card Video Recorder or Front End application is displayed IP address is set by its range and be added and be deleted The IP address of the Front End application or Memory Card Video Recorder set here will be the target for remotely updating uploading videos or videos The Back End Server tries to connect to the Front End application or Memory Card Video Recorder whose IP address is set on this screen Confirming the Front End IP address The IP address of the Front End application for communicating with the Back End Server is displayed on the Front End IP Address list Confirming the Recorder IP address The IP address of the Memory Card Video Recorder for direct communicating with the Back End Server is displayed on the Recorder IP Address list Adding an IP address 1 Click on Add The IP Address Setting screen is displayed 2 Enter the IP address IP Address Setting es E E 82 3 Click on OK The entered IP address is added to the address list on the DB Network setting screen 4 Click on Apply The address will be regis
104. or to make settings for operating the Memory Card Video Recorder Front End applications Back End Administrator application and Back End Client application Updating software Firmware of the Memory Card Video Recorder Front End application Back End Administrator application and Back End Client application can be remotely updated to the latest version User registration Administrators and officers who use the Front End application Back End Administrator application and Back End Client application are registered as users Grouping users Registered users can be grouped Once they are grouped information for multiple users can be updated easily Defining rules Rules for registering videos to the database can be defined Defining classify tag Classify tags used for searching for can be defined System setup Setting for the Back End Server can be made Overview continued Operating Environment APC that meets the following operating environment is required for use of this application CPU Intel Core Duo 1 66 GHz or more recommended RAM 512 MB or more for Windows Vista Business 1GB or more recommended Display 1024 x 768 dot or more LAN 1000BASE T 100BASE TX OS Windows XP Professional Service Pack 3 or later Windows Vista Business Service pack 2 or later Add on Net Framework 3 5 Service Pack 1 Windows Installer3 1 Adobe Reader 8 or 9 Installing Uninstalling Installing Remote updating
105. order they will be deleted from the list Note Enter note of the user Password Enter the password If the user ID is imported from Active Directory entering of the password is disabled Retype Password Retype the password to confirm it If the user ID is imported from Active Directory retyping of the password is disabled Right List Check the rights to be given to the user View your own non Arbitrator video files and Playback your own Arbitrator video files AV video are checked as default Right clicking enables selecting all rights and clearing all rights See Right list page 57 Select All Check the all rights Clear All Uncheck the all rights 56 Operations continued Right list The rights shown in the table below can be set on the Right List of the Property screen Right Description Import Arbitrator video files AV video Allow the user to import the AV video files from SD card P2 card or other media Import non Arbitrator video files Create Case File Allow the user to import the files except AV videos recorded by VPU from SD card P2 card or other media Allow the user to create case file Run Report Allow the user to run the reporting Manage Update Allow the user to create delete modify remote update settings Manage Users Groups Allow the user to create delete modify users and user groups
106. oth the IP address and subnet mask The IP address subnet mask or default gateway is incorrect e They are configured as four numbers delimited by periods each in the range of 0 to 255 Input correct values The value for the IP address is invalid e The IP address is configured as four numbers delimited by periods each in the range of 0 to 255 Input the password again The gateway address is invalid e Check that the IP address and gateway are set on the same subnet The subnet mask is invalid e Check that the subnet mask in the network section and that in the host section are correct The length of the character string is 5 or 13 Or if the length of the character string is 10 or 26 please input character 0 9 a f A F that shows the hexadecimal number The length of the character string is eight or more and 63 or less Or if the length of the character string is 64 please input character 0 9 a f A F that shows the hexadecimal number Cannot set the same IP Address Set the different IP Address The snapshot folder doesn t exist There is no snapshot in the folder The length of the encryption key WEP is invalid e Check that the length of character string is 5 or 13 If it is 10 or 26 check that it is the hexadecimal number using characters 0 9 a f A F The length of the encryption key WPA is invalid e Check that the length of character string is eight or more and 63 or less If it is 64
107. pplication Description of the Screen Displays continued DB Network setting screen Port setting When the DB Network setting tab on the Config screen is clicked on the database and network setting screen is displayed See Setting the Database and Network page 80 60 pak tns mint 20998 EEx For setting the port E arbitrator 3 strator 2 Update Users Groups Rules Classify Config Back End Server Destination Connect to Back End Client Administrator TCP For confirming the port number for communicating the Back End Administrator or Back End Client application and Back End Server to process the request such as Login Video search etc Update Back End Client Administrator TCP For confirming the port number to update the Back End Administrator or Back End Client module from the Back End Server Update from Front End TCP For confirming the port number to update the module for an administrator from the Back End Server Setting for the database will be made SQL server For setting the database server to be connected The database servers detected automatically will be displayed on the dropdown list Database For setting the database Z Streaming is not available at present Upgrading is Database managed by the specified database eare or te UTE server is displayed Select the database from the dropdown list Proxy setting Streaming is not available at present Upgrading is schedu
108. ps Update Version display For displaying the software version for updating Register button For registering the Front End application in the Back End Server Front End list For displaying the list of the Front End application detected by the Back End Server Right clicking enables deleting the Front End application and refreshing the screen Valid Check the check box and the corresponding Front End application will be updated PC Name Name of the PC with the Front End application installed Version The current version of the Front End application installed Last Update Date Time The last applying date and time of the Front End applications Status The update status of the Front End applications e Wait for Update e Updating e Updated e Disconnected Select All button All Valid check boxes for the Front End application shown on the Front End list are checked Clear All button All Valid check boxes for the Front End application shown on the Front End list are unchecked Delete button For deleting the Front End application selected on the Front End list from the database Refresh button For refreshing the Front End list Description of the Screen Displays continued Back End Update screen Delete button os For deleting the Back End application selected on When the Back End Update tab on the Update the Back End list from the database screen is clicked on the Back End Update screen
109. r For displaying the full path of the Front End and Memory Card Video Recorder log files Capacity restrictions For setting the capacity of the Front End application and Memory Card Video Recorder log files The log is deleted from the oldest one when the capacity exceeds this value Browse button For opening the Server Folder Setting dialog box for selecting the Root Path of the Front End application and Recorder 21 Description of the Screen Displays continued Schedule setting screen Alert Setting When the Schedule setting tab on the Config screen is clicked on the schedule setting screen is displayed See Schedule Setting page 76 ules Classify Config Alert settings will be made Set the Time of no connection to Front End Recorder to send e mail If a certain recorder has not uploaded video files exceeding the specified days the warning e mail is sent to the specified group Default setting 7 days Send to The destination of e mail is specified Default setting Empty Schedule setting For setting the schedule Work Start Time For entering the start time of the batch processing Default setting is 00 00 Work Time For entering the time of the batch processing Setting values 1 hour 2 hour 3 hour 5 hour Until End Default setting 2 hour Case File Records Retention When checked the longest retention period from among all files associated to th
110. r3 or Server4 is selected the IP Address Subnet Mask and Gateway are fixed as shown below If Off is selected the IP Address Subnet Mask and Gateway can be changed DOO Seven Server Serves ____ Server4 OFF IP Address 192 168 10 10 192 168 217 192 172 24 217 192 10 216 217 192 192 168 1010 Subnet Mask 255 255 255 0 255 255 255 0 255 255 255 0 255 255 255 0 255 255 255 0 Gatewy b S bh E b b E 91 Setup continued Embedded OSD The settings for Embedded On Screen Display can be performed Item Factory Preset Description Embedded OSD Setting of whether Embedded OSD is displayed or not Main ON Embedded OSD display setting for the Main video Setting values ON OFF Sub ON Embedded OSD display setting for the Sub video Setting values ON OFF Display Position Upper Left Setting of Embedded OSD display location Setting values Upper Left Upper Right Bottom Left Bottom Right Embedded OSD Item Settings of display items Time ON Date Time display setting Setting values ON OFF Trigger ON Embedded OSD display when trigger signals GPI1 16 are input Setting values ON OFF VehiclelD Area OFF Setting of whether the vehicle identification data and location name are displayed Setting values ON OFF 92 Setup continued Radar GPS Settings related with a radar gun and GPS Item Factory Preset Description Radar Settings related with a radar gun Connecti
111. re no files to export No export operation needed E28400 No USB storage devices found Connect a USB memory device Couldn t start export E28401 Write Protect cards found Disable SDHC Memory Card write protection Couldn t start export E28402 All USB storages are read only Connect a write enabled USB memory device Couldn t start export E28403 Media error Replace the SDHC Memory Card or the USB memory device Export was incomplete E28404 USB storage file system error Replace the USB memory device Couldn t start export E28405 USB storage write error Export was incomplete E28406 Found update file in USB storage Delete the update file on the USB memory device Couldn t start export E28407 No SDHC Cards found Insert an SDHC Memory Card with recorded files Couldn t start export E28409 Couldn t start export Replace the SDHC Memory Card E28499 System error Reboot the recorder Export was incomplete E28880 ae storage was T Do not remove the USB memory device while exporting data Reconnect xport was incomplete the USB memory device and export again E28881 USB storage was inserted Export the data again Export was incomplete E29400 Unsupported camera connection camera is connected only to the CAMERA 4 CAMERA 5 or CAMERA 6 connector Check the input E29401 No CAMERA 1 video signal CAMERA 1 connector input cannot be detected Check whether the signal is
112. roperly made 21020 Failed to get the user information Acquisition of user data failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 21030 No user ID input No user ID has been input Input the user ID 21040 The passwords you typed do The input password is wrong Input a correct password not match Please retype the passwords 21050 Failed to update the DB DB data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 100 Error Messages continued 54060 Failed to get the password information 21050 22000 Failed to update due to illegal data Please confirm the input information Failed to get the data from Active Directory Server Failed to update due to illegal data Please confirm the input information Failed to update due to illegal data Please confirm the input information Too many registered data 22010 23000 30000 30002 30010 Failed to get the group Information Failed to delete the group information Failed to update due to illegal data Please confirm the input information Failed to get the group Information 31020 Failed to get the user information Message Measure Acquisition of password information failed Verify with the administrator that the BES and DB have started Check also that the network c
113. rs tab or Groups tab and selection is canceled Note The Rule Name cannot be edited 3 Click on OK The Rules screen is updated 4 Click on Apply The updated rule is registered in the database Note For the following cases an error message appears e Permission Users Groups is set but Permission Rights is not set e Retention period is not specified e Storage location is not specified 67 Operations continued Deleting a rule k End Administrator 2 0 39 51 Arbitrator 300 Back jstrator Update Users Groups Rules Classify Config 1 Select a rule to be deleted on the Rules screen 2 Click on Delete A confirmation dialog box is displayed 3 Click on Yes The confirmation dialog box is closed and the rule will be deleted from the Rules screen 4 Click on Apply The rule is deleted from the database Cancel deleting Click on No in the confirmation dialog box or Cancel on the Rules screen 68 Operations continued Setting Classify Information Classify is the function to add classify tag and classify note to the video Videos can be searched for using the classify information On the Classify screen the classify tag can be created edited and deleted Up to 50 classify tags can be defined Even if the predefined classify tag is edited the classify tag that has already been added to the video will not be changed Click on Cla
114. rted Check also that the network connection is properly made 55000 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input etc Make sure that the input data are correct information No Server information input An error was generated while updating screen data because of illegal data etc Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 55110 Failed to get the network Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made 55120 Failed to get IP Address Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made 55200 Failed to set the information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 55220 Failed to set IP Address Data writing failed Verify with the administrator that the BES and DB have information started Check also that the network connection is properly made 55230 Failed to set the network Data writing failed Verify with the administrator that the BES and DB have information started
115. ry Preset Init Settings after power ON Description Initial settings upon power on Init Preset Select Preset 1 Initial Preset setting Setting values Preset1 Preset2 Preset3 LAST Init Video Out 1 Video Out2 Setting of the throughout video signal to the VIDEO OUT 1 connector Setting values CAM1 CAM3 Video Out2 LAST Classify Classify information setting Force Classify DISABLE Addition of classify information Setting values DISABLE No addition ENABLE Addition permitted FORCE Forcible addition Storage Capacity Warning Classify information setting Remaining 60 A warning sounds when the remaining recordable time becomes Recordable Time shorter than the value set here min Setting values 30 60 90 minutes Warning sound OFF Select if a short beep is to sound twice every 30 seconds when the remaining recordable time becomes shorter than the set value Setting values ON OFF 1 Depending on the settings on the Video Allocation screen some items may not be displayed 2 The setting upon the last power off will be restored when the camera is turned on If the Memory Card Video Recorder is not turned off properly the setting data upon power off may not be stored properly 95 Setup continued Registration Various data can be registered Item Factory Preset Description Meta Definition Administrator Select the type of meta definition to be r
116. s 0 Acamera is connected X A camera is not connected 118 Panasonic Computer Solutions Company 50 Meadowlands Parkway Panazip 2F 5 Secaucus NJ 07094 Panasonic Corporation 2009
117. s displayed 2 Enter the required information in the Servers Setting section ActiveDirectory Servers Setting 3 Click on Connect Users registered in the Active Directory are displayed on the Users tab and Groups are displayed on the Groups tab 4 Select a user or group to be registered Multiple users or groups can be selected 5 Click on gt The selected user or group moves to the Registered Users List or Registered Groups List 6 Click on OK The Active Directory screen is closed and the user or group will be registered Description of Active Directory screen D Domain Select the server name or IP address of the Active Directory server on the dropdown list User Enter the user name who is enabled to log into the Active Directory server Password Enter the login password in the Active Directory field Connect For connecting to the Active Directory server Users Users registered in the Active Directory server are listed Right clicking enables the operation of the gt button Groups Groups registered in the Active Directory server are listed Right clicking enables the operation of the gt button Registered Users List User name registered in the database are listed when the Users tab is selected Right clicking enables the operation of the lt button Registered Groups List Group name registered in the database are listed when the Groups ta
118. s the minimum password length is greater than the maximum value is set to the maximum password length minimum value of the length of password 54022 The minimum value of the length The minimum value for the password length is incorrect Specify a value in of password is illegal Please set the range of 6 to 12 the value within the range of 6 to 12 The maximum value of the length The maximum value for the password length is incorrect Specify a value in of password is illegal Please set the range of 6 to 12 the value within the range from 6 to 12 The validity term of the password The validity term of the password is too long The maximum term that can be is too long The maximum terms set is 4000 days that can be set are 4000 days 54100 Failed to get the information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 54110 Fail to get the password Acquisition of the information failed Verify with the administrator that the information BES and DB have started Check also that the network connection is properly made 54200 Failed to set the information Data writing failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 54210 Failed to set the password Data writing failed Verify with the administrator that the BES and DB have information sta
119. screen Valid Check the check box and the corresponding recorder setting will be updated VehiclelD The Vehicle ID If the Valid check box is unchecked single clicking enables editing Group For displaying the group to which a Memory Card Video Recorder belongs Recorder Setting Name For selecting the setting applied to the Memory Card Video Recorder from among predefined settings or None setting If the Memory Card Video Recorder belongs to a group the selected setting is applied to all recorders in the group 14 Last Update Date Time Displays the last applying date and time of the setting of the Memory Card Video Recorder Recorder Version The current version of the firmware of the Memory Card Video Recorder Model The model name of the Memory Card Video Recorder available on the AG CPD20P only Serial The serial number of the Memory Card Video Recorder available on the AG CPD20P only MAC Address The MAC address of the Memory Card Video Recorder s network interface for connecting with the Front End application IP Address The IP address of the Memory Card Video Recorder Status The update status of the Memory Card Video Recorder e Wait for Update e Updating e Updated e Disconnected Select All button All Valid check boxes for the Memory Card Video Recorders shown on the Recorder list are checked Clear All button All Valid check boxes for the Memory Card Video Recorders shown on the Re
120. ssify and the Classify screen is v I Arbitrator 300 Back End Administrator 2 0 39 51 Update Users Groups Rules Classify Config Adding a classify tag 1 Click on Add on the Classify screen The Input Classify Tag screen is displayed Enter a classify tag Input Classify Tag Click on OK The Classify Tag screen is closed and the Classify List is updated A maximum of 99 alphanumeric characters and symbols excluding lt gt W amp and can be used in a classify tag displayed 69 Editing the classify information 1 Select the classify tag to be edited on the Classify List Click on Edit The Input Classify Tag screen is displayed Edit the classify tag Click on OK The Classify Tag screen is closed and the Classify List is updated Deleting the classify information 1 Select the classify tag to be deleted on the Classify List Multiple tags can be selected Click on Delete A confirmation dialog box is displayed Click on Yes The confirmation dialog box is closed and the classify tag is deleted Cancel deleting Click on No in the confirmation dialog box System Setup When you click on the Config button on the Main screen the system setup screen appears Rules Classify Contig Apply button All settings changed on each setting screen are registered in the database Cancel button All settings changed
121. t setting See Schedule setting screen page 22 System Setup continued Unprocessed video setting When the video is verified and unprocessed it will be saved to the Unprocessed Video Folder then e mail is automatically sent to the users who belong to the group specified in Alert Setting See Schedule setting screen page 22 Consult your supplier Specifying the folder 1 Click on Browse The Server Folder Setting dialog box appears 2 Select the folder 3 Click on OK The full folder path for the Unprocessed Video Folder is displayed Setting the retention period The retention period of the unprocessed video file is fixed to unlimited 73 System Setup continued Log Setting Setting for log output is made Click on the Log setting tab The log setting screen appears Operation log setting Arbitrator 160 Back End Ad 202951 Update Users roups Rules Classify Config The retention period of the User Operation Log is set Enter the days of retention period in A log save period field 74 System Setup continued Front End Application Recorder Log setting Arbitrator 360 Back End Administrator 2 0 39 51 Update Users Groups Rules Classify Config The location and capacity restriction for storing the user operation log of the Front End application and Memory Card Video Recorder are set Setting the folder for storing the log 1 Click o
122. t be started E15766 Write Protect Card found on slot4 Record cannot be started E15767 No SDHC Cards found No SDHC Memory Card is inserted Insert an SDHC Memory Card Record cannot be started E15768 Write Error Data cannot be written to the SDHC card Replace the SDHC Memory Card Record cannot be started E15769 Card Full The following conditions may have occurred Record cannot be started e There is no space left on the SDHC Memory Card e Files contained in one of the SDHC Memory Cards inserted in the SDHC Memory Card slots 1 2 3 and 4 exceed 5 000 files Replace the SDHC Memory Card with an SDHC Memory Card with free capacity or free up space of 10 Mbytes or more in the SDHC Memory Card for new data E20801 Recorderreboots by Be sure to use the correct procedure to remove and load SDHC Memory unrecoverable card ejection error Cards E20802 Please reinsert the card or reboot Check the SDHC Memory Card and re insert it or reboot the Memory Card the system Video Recorder E20901 Firmware Update FAILED An error occurred during the update e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device e Check whether there are multiple update files on the USB memory device e Check whether there are multiple USB memory devices containing update files e A USB memory de
123. ted and the Recorder Setting screen is updated 6 Click on Cancel 34 Operations continued Deleting the Memory Card Video Recorder Grouping the Memory Card Video settings Recorders 4 Click on Settings If multiple Memory Card Video Recorders are grouped the settings on all recorders belonging to a group will The Recorder Setting screen is displayed be created and changed 2 Select a Setting Name to be deleted on the Recorder Setting list 1 Click on Add Group 3 Click on Delete The Recorder Group screen is displayed A confirmation dialog box is displayed 4 Click on Yes The selected setting is deleted and the Recorder Setting screen is updated 5 Click on Close 2 Enter the group name in the Group Name field Cancel deleting Click on No in the confirmation dialog box 3 Select Vehicle IDs to be grouped on the Vehicle ID and Group List Multiple Vehicle IDs can be selected 4 Click on gt gt The Vehicle IDs selected in Step 3 moves to the Vehicle ID list 5 Click on OK A Group is created and the Recorder Group screen is closed The created group is registered in the database 35 Operations continued Description of the Record Group screen Editing the Memory Card Video Recorder group Group Name Enter the group name Vehicle ID and Group List Vehicle ID and their group name that do not belong to the group displayed in Group Name are liste
124. tered to the database Notes e The top three octets of IP address for To cannot be entered e For the following cases an error message appears The address is not entered The address is invalid Deleting IP address 1 Select the address to be deleted on the address list Multiple addresses can be selected 2 Click on Delete A confirmation dialog box is displayed 3 Click on Yes The selected address is deleted and the DB Network setting screen is updated 4 Click on Apply The updated address will be registered to the database Cancel deleting Click on No in the confirmation dialog box or Cancel on the DB Network setting screen Streaming is not available at present Upgrading is scheduled for the future Setup Admin Password Perform video and audio settings Item Factory Preset Description Admin Password Password admin Retype Password For inputting an administrator password Allocation Video Audio Perform video and audio settings Item Factory Preset Description Resolution RecordRate The resolution and bit rate of the video can be set Main D1 HI The resolution and bit rate of the main video can be set Setting values D1 HI D1 STD D1 10 CIF Sub D1 HI The resolution and bit rate of the sub video can be set Setting values D1 HI D1 STD D1 10 CIF Conne
125. ther there are multiple USB memory devices containing update files The update file on the USB memory device is corrupted e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device Some other update error occurred e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device No update file could be found on the USB memory device e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device The used USB memory device cannot be used for updating e A USB memory device containing a folder other than the WIDKEY folder cannot be used for updating An update file load error occurred e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device Some other update error occurred e Check whether the update file for the recorder has been correctly copied to the USB memory device e Reformat the SDHC Memory Card or USB memory device before use e Use another USB memory device A conn
126. time for automatic switching of the IR function Setting values 10 30 60 300 seconds Auto Zoom Magnification Set the maximum zoom magnification during automatic zooming Setting values 1 2 3 4 5 7 10 15 22 Auto Zoom Time s Set the keeping time of the maximum zoom magnification during automatic zooming Setting values 3 5 8 seconds 41 Auto Zoom End Position Set the automatic zooming end magnification Setting values 1 2 3 4 5 7 10 15 22 LAST Zoom Limit Set the maximum zoom magnification Setting values 22 220 AGC Level Set the level of the camera input gain control Setting values LOW MID HIGH OFF Flip Set if flipping of the camera output image will be performed or not Setting values ON OFF Auto Focus Set a focusing method of the camera Setting values PRESET DISABLE AUTO Operations continued Init Camera Settings after power ON Bast auto Last BLE DISABLE The status of the color camera when it is turned on can be set Init Backlight Set the backlight compensation function setting upon power on of the Memory Card Video Recorder Setting values ON OFF LAST Init IR Mode Set the IR mode upon power on of the Memory Card Video Recorder Setting values ON OFF AUTO LAST Init Camera 1 LED Set the status of the REC lamp on the camera connected to the CAMERA 1 connector on the Memory Card Video
127. tion order for access points Move Down button For lowering the priority of the connection order for access points 46 Access Point Setting screen This screen is displayed when the Property button is pressed on the Network screen Access Point Setting Access Point DISABLE 4 SSID Security Network Key Key Index Access Point Select if the access point settings are enabled or not Setting values ENABLE DISABLE SSID Set the SSID for the wireless LAN module connected to the Memory Card Video Recorder Security Set the encryption method for the wireless LAN module connected to the Memory Card Video Recorder Setting values WEP WPA WPA2 PSK NONE Network Key Set the network key for the wireless LAN module connected to the Memory Card Video Recorder when Security is set to WEP or WPA Key Index Set the network key index for the wireless LAN module connected to the Memory Card Video Recorder when Security is set to WEP Setting values 1 2 3 4 OK button For registering the settings to the SSID list Cancel button For canceling the settings Operations continued Embedded OSD screen Main Select if the Embedded OSD is displayed on the main video or not Setting values ON OFF Sub Select if the Embedded OSD is displayed on the sub video or not Setting values ON OFF Display Position Set the Embedded OSD display position Setting values Upper Le
128. tory Preset Description Date Time Date time and time zone settings Time Zone Eastern Daylight Saving Time Time zone Hawaii Standard Time Yukon Standard Time Yukon Daylight Saving Time Pacific Standard Time Pacific Daylight Saving Time Mountain Standard Time Mountain Daylight Saving Time Central Standard Time Central Daylight Saving Time Eastern Standard Time Eastern Daylight Saving Time Atlantic Standard Time Atlantic Daylight Saving Time Asia Tokyo Date Time Style USA Date Time display style setting Setting values ISO YYYY MM DD HH MM SS USA MM DD YYYY HH MM SS Date Night View Day Night mode setting Day Night View Checked Select if Day and Night views are automatically switched or not Auto Switch Switch to Day View 7 00 00 AM Time setting for switching to Day mode at Setting range 00 00 00 AM 11 59 59PM Switch to Night 6 00 00 PM Time setting for switching to Night mode View at Setting range 00 00 00 AM 11 59 59PM 89 Setup continued File Transfer File transfer settings can be performed Item Factory Preset Description Upload Upload settings Auto Upload is Unchecked Select whether automatic uploading is enabled or not Enabled Server IP Address IP address of the Back End Server for manual uploading for Manual Upload EXBSRIDVD Burn Confirmation Select how to delete video files from the Memory Card Video Recorder
129. ue Mic microphone Wireless Mic wireless microphone Off no connection Audio4 OFF The audio signal connected to the AUDIO IN 4 connector can be selected Setting value Mic microphone Wireless Mic wireless microphone Off no connection Init Audio Rec after ON Initial audio output setting upon power on power ON Setting values ON OFF LAST 1 Selectable Form and Pattern of Preset1 Preset2 4 The setting upon the last power off will be restored and Preset3 depend on the settings of Connection when the camera is turned on If the Memory Card Camera Video Recorder is not turned off properly the setting 2 This setting is enabled when the camera connected data upon power off may not be stored properly to the CAMERA 1 connector is set to OFF 3 None is not selectable for Preset1 unless all camera connections are set to OFF 86 Setup continued Camera 1 Camera 1 settings can be performed Item Factory Preset Description Camera 1 Settings for the color camera connected to the CAMERA 1 connector on the Memory Card Video Recorder IR Level LOW Level setting for automatic IR switching Setting values LOW HIGH IR Time s 30 Level detection time for automatic IR switching seconds Setting values 10 30 60 300 Auto Zoom 10 Maximum magnification setting for automatic zooming Magnification Setting values 1 2 3 4 5 7 10 15 22 Auto Zoom Time s 3 Keeping tim
130. uired free space in the Minimum Free Space field When the free space on the drive falls below this value an alert e mail message is sent to the users who belong to the group specified in Alert setting See Schedule setting screen page 22 71 System Setup continued 6 Click on OK The Register folder dialog box is closed and the Library is updated Deleting a folder 1 Select a folder to be deleted in the Library list Multiple folders can be selected Click on Delete The confirmation dialog box is displayed Click on Yes The confirmation dialog box is closed and the selected folder is deleted Note The folder used by Evidence rule cannot be deleted Cancel deleting Click on No in the confirmation dialog box or Cancel on the Drive setting screen 72 Archive setting inistrator 2 0 29 Groups Rules Classify Config Arbitrator 300 Back Update Us Assign a folder to which archive videos are to be stored Only one folder can be set Changing the folder 1 Click on Browse The Server Folder Setting dialog box appears Select the folder Click on OK The full folder path for Archive Folder is displayed Setting the minimu free space Enter the minimum free space in the Minimum Free Space field When the free space on the drive falls below this value an alert e mail message is sent to the users who belong to the group specified in Aler
131. use of illegal data etc Make sure that the input data are correct 14100 Failed to get the information 14110 Failed to get the machine Information Failed to get the software Information Failed to get the group Information Failed to get the free field information Failed to set the Information Failed to set the installation information Failed to set the machine Information 14300 Failed to delete the machine information 14400 Too many registered data 15000 Failed to update due to illegal data Please confirm the input information 15002 Too many registered data 15100 Failed to get the setting information Failed to get the setting information Failed to delete the setting information Failed to edit the setting information Failed to update due to illegal data Please confirm the input information Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Acquisition of the information failed Verify with the administrator that the BES and DB have started Che
132. value 16200 Failed to set the information Setting of the information failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made 16110 Failed to set the machine Setting of the information failed Verify with the administrator that the BES Information and DB have started Check also that the network connection is properly made 16220 Failed to set the group Setting of the information failed Verify with the administrator that the BES information and DB have started Check also that the network connection is properly made Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input _ etc Make sure that the input data are correct information 17100 Failed to get the data Acquisition of VPU setting data failed This error is not generated in normal situations 17110 Fail to decompress the data Acquisition of VPU setting data failed This error is not generated in normal situations 17000 Failed to update due to illegal An error was generated while updating screen data because of illegal data data Please confirm the input _ etc Make sure that the input data are correct information Failed to upload Uploading failed Verify with the administrator that the BES and DB have started Check also that the network connection is properly made Failed to update due to illega
133. vice containing a folder other than the WIDKEY folder cannot be used for updating 20911 Microcontroller Update FAILED An error occurred during the update The Memory Card Video Recorder reboots automatically to restart an update Contact your supplier if the problem persists Contact your supplier E20921 AG RCP3O Update FAILED An error occurred during an update of an AG RCP30 connected to the Memory Card Video Recorder The Memory Card Video Recorder reboots automatically to restart an update E20912 Sea Microcontroller The Memory Card Video Recorder has broken down Contact your supplier if the problem persists 20922 Unsupported Control Panel A Remote Control Panel not supported by the Memory Card Video Recorder Detected was detected Disconnect the Remote Control Panel 110 Error Messages continued Message Measure E22420 Officer s information file cannot be The officer data file WID TXT is corrupted Create a new officer s data file loaded save it to a USB memory device and re register it E22421 Since you are not an You are not registered as an administrator and cannot open this menu Ask aud ea you cannotopen 2 registered administrator for assistance is menu Officer s information file cannot be There is no Officer Registration file or it contains the wrong data Create a loaded correct Officer Registration file WOFFICER TXT copy it to a USB memory device and reload it
134. yed See Drive Setting page 71 Delete button For specifying the folder path for the Video Inbox where temporarily stores the video files uploaded from the Front End application Memory Card Video Recorder or Back End Client application Video Inbox For displaying the folder path for the Video Inbox Browse button The Server Folder Setting dialog box opens to select the Video Inbox Library Setting For specifying a folder in which videos are to be stored Library For displaying the list of the folder path of folders where video files are to be moved from the Video Inbox Right clicking enables adding or deleting the folder path Path The full path for the folders which store the video files Minimum Free Space The minimum disk space When free space is less than this size e mail is automatically sent to the users who belong to the group specified in Alert Setting See Schedule setting screen page 22 Free Space The current disk space 20 For deleting a folder selected on the Library Archive Setting For setting the Archive folder Archive Folder For displaying the full folder path for the Archive folder Minimum Free Space Enter the minimum free space When the free space is less than this size the e mail is automatically sent to the users who belong to the group specified in Alert Setting See Schedule setting screen page 2
135. yed See System Setup page 70 Arbitr tor 360 Update Back I nd Ak Users Rules Video Inbox Setting Classify Config Ubrary Setin Path Drive setting tab For displaying the drive setting screen for setting the destination to register video files See Drive setting screen page 20 and Drive Setting page 71 Log setting tab For displaying the log setting screen for setting log output See Log setting screen page 21 and Log Setting page 74 Schedule setting tab For displaying the schedule setting screen See Schedule setting screen page 22 and Schedule Setting page 76 Password setting tab For displaying the password setting screen for setting the password policy See Password setting screen page 23 and Setting the Password page 78 DB Network setting tab For displaying the database network setting screen See DB Network setting screen page 24 and Setting the Database and Network page 80 Apply button All settings and changes made on each setting screen will be registered to the database Cancel button For canceling all settings and changes made on each setting screen 19 Description of the Screen Displays continued Add button For adding a new folder in which videos are to be stored Drive setting screen When the Drive setting tab on the Config screen is clicked on the drive setting screen is displa

Panasonic Arbitrator 360 Operating Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents