Orion Car Audio RGC-1 User's Manual
Contents
1. INTRODUCTION The RGC 1 remote gain control is specifically designed for use with ORION amplifiers The RGC 1 allows dashboard control to your current Orion amplifier or earlier XTR XTR Pro or HCCA amplifier Used on subwoofer amplifiers it provides subwoofer level control Used on the first amplifier in a daisy chain it works as a remote pre amp volume control Warning The RGC 1 can be used only on ORION amplifiers that have a 1 8 inch mini jack remote gain port on the connection panel Using the RGC 1 with other ORION products will damage the system OPERATION The RCG 1 is shipped in its retracted position To adjust the control press and release the knob The knob will extend for adjustment Clockwise rotation of the control knob increases the gain of the amplifier Counterclockwise rotation reduces the gain See the Adjustment section for information on how to set the various level controls in the system to get the proper range of operation for the RGC 1 The control knob can be pushed in to its retracted position after adjustment WIRING Connect the RGC 1 to the ORION amplifier connector with the attached 1 8 inch mini plug cable If your system requires a longer cable a standard head phone extension cable can be used The RGC 1 has an optional night time illumination provided by the GREEN WHITE and a RED WHITE wires For Red color illumination connect the RED WHITE wire to a 12 Vdc source and the GREEN WHITE wire to c2. an does Tab y or other causes not arising out of defects in materials or construction ALL WARRA INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IMPLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS Unit must be a returned to Directed postage pre paid with consumer s name telephone number and address authorized dealer s name and address and product description IN ORDER FOR THIS WARRANTY TO BE VALID YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION WILL BE COVERED BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY Note This warranty does not cover labor costs for the removal and reinstallation of the unit BY PURCHASING THIS PRODUCT THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY CALIFORNIA Directed Electonics is a proud member of Designed and Engineered in the USA by 9001 AA Di SH CCELA ELE
3. CTRONICS INC apply to any unit that has been modified or used in a manner contrary to its intended purpgg and does not cover damage to the unit caused by installation or removal of the unit This war is void if the product has been damaged by accident or unreasonable use neglect improper 2003 Directed Electronics Inc All rights reserved G58000 9 03
4. hassis ground For Green color illumination connect the GREEN WHITE wire to a 12 Vdc source and the RED WHITE wire to chassis ground INSTALLATION Under Dash Mounting To mount the RGC 1 under the dash or in an area that cannot be drilled through to accom modate the control use the supplied under dash mounting bracket Find a suitable location which will not interfere with driving that is easy to reach Mount the bracket in place using the 2 screws and secure the RGC 1 to the bracket as shown below 2003 Directed Electronics Inc 1 Under Dash Mounting Screws In Dash Mounting Note There must be enough clearance behind the dash panel before selecting the location to mount the RGC 1 A 1 2 inch hole must be drilled to mount the RGC 1 in the dash panel Side in the control from the rear of the dash panel and place the trim label on the threaded shaft Secure the control with the nut and mount the knob If there is no access to the back of the dash panel drill a 3 4 inch hole in order to pass the entire RGC 1 through the hole from the front of the dash panel Once the control is through the hole the clip shown below is passed through the hole and slid around the threaded shaft of the control Place the trim label on the threaded shaft and secure the control with the nut and mount the knob Front Mount Dashboard A Trim Panel Rear Mount 2 2003 Directed Electronics Inc ADJUSTMENT PROCEDURE 1 Set the gain c
5. ontrols of the amplifier according to the Adjusting the Sound of Your System in your owner s manual The amplifier primary gain controls determine the maximum allowed output level that the amplifier 2 Set the control knob of the RGC 1 to its mid rotation position 3 Check the output level of the subwoofer The amount of bass can be adjusted for the type of music and individual preference Warning DO NOT increase the amplifier gain without repeating Step 1 Failure to do so may damage your amplifier and speakers This will void your warranty 2003 Directed Electronics Inc Warranty TE LIMITED TWO YEAR CONSUMER WARRANTY Directed Electronics Inc promises to the original purchaser to replace this product should i to be defective in workmanship or material under normal use for a period of two years date of purchase by the dealer as indicated by the date code marking of the product PRO the product was installed by an authorized Directed dealer During this two year period th ar be no charge for this replacement PROVIDED the unit is returned to Directed shippin pr If the unit is installed by anyone other than an authorized Directed dealer the warranty per be 1 year from date of purchase by the dealer as indicated by the date code marking of product During this 1 year period there will be no charge for this replacement PROVID ED unit is returned to Directed shipping pre paid This warranty is non transferable
Download Pdf Manuals
Related Search