Oreck XL2800H2 User's Manual
Contents
1. it snaps Operating Instructions To Operate Make sure the disposable paper filter dust bag is in place DO NOT operate the cleaner without a paper filter dust bag Plug the power cord into an electrical outlet Choose from the low and high speed settings by pressing the ON LOW I ON HIGH Il OFF O switch on handle assembly when ready to operate General Information The performance of your new cleaner greatly depends upon care and maintenance The instructions in this manual will guide you in performing basic care and maintenance To obtain the most satistying years of service read the instructions and keep them handy for future reference Operating Recommendations This new ORECK XL High Speed Upright is one of the finest fastest and strongest units in its class You ll love the way it cleans gets under things and it s SO lightweight and easy to Use The following are a few simple suggestions regarding its operation 1 When inserting a new disposable paper filter dust bag FIRST PUFF OUT and OPEN THE BAG 2 When the disposable filter dust bag is full REPLACE IT 3 If at any time the machine does not pick up properly or makes an unusual noise STOP OPERATION and service 4 Although your upright will pick up pins paper clips and other small objects it is recommended that these be removed from the floor before you vacuum Failure to do so may result in permanent damage to the motor suction fan and it2. MANUFACTURING COMPANY ORECK gives you the following limited warranty for this product only if it was originally purchased for use not resale from ORECK or an ORECK Authorized Retail Dealer ORECK will repair or replace free of charge to the original purchaser any part which is found to be defective in material or workmanship within three 3 years of the date of purchase 10 years on housing This limited warranty applies to normal domestic use Any commercial use of this product will void this limited warranty Drive belts revolving brushes bulbs disposable bags and other parts subject to normal wear are not covered by this limited warranty This limited warranty does not apply to any part subjected to accident abuse commercial use alteration misuse damage caused by fire or act of God the use of voltages other than indicated on the serial number plate of this product or service of this product by other than ORECK or an ORECK Factory Authorized Service Center ORECK does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product ORECK s limited warranty is valid only if you retain proof of purchase from ORECK or an ORECK Authorized Retail Dealer for this product If you purchase this product from any other source your purchase is AS IS which means ORECK grants you no warranty and that you not ORECK assume the entire risk of the quality and performance
3. Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket This lightcolored pocket is located inside the vinyl bag in the area where the paper disposable bag attaches to the intake tube Insert tablet in pocket Troubleshooting Guide e Is the disposable filter dust bag full e Are pores of filter dust bag clogged with powder or fine dust e s anything clogging the revolving brush lower tube intake opening fan housing or connector assembly opening PROBLEM CLEANER WILL NOT RUN Is the belt in place and turning the brush Are the brush ends in the proper location Does the brush turn freely Are hair string or rug fibers wound around the brush POSSIBLE SOURCE Not plugged in properly No electricity in wall outlet Plug not firmly in handle assembly WARNING Unplug cord from electrical outlet before servicing SAVE SERVICE CALLS CHECK THESE FIRST AREAS TO CHECK Be sure cleaner is firmly plugged into wall outlet Check electrical source fuse or circuit breaker Plug firmly in handle assembly CLEANER DOES NOT PICK UP Filter bag is full Nozzle or intake pivot clogged Belt is broken or stretched Brush is worn Bag tube clogged Bag pores are clogged with fine dust Impeller fan is broken Revolving brush is not even at both ends Replace filter bag See To Install Paper Filter Dust Bag Clear obstruction Replace be
4. cleaning ability of your cleaner and could cause damage to it The Belt The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the etfective operation of the cleaner If the belt becomes stretched or cut it will cause the revolving brush to stop completely or slow down See instructions in the manual for replacing belt An extra belt is stored in the base plate of your cleaner When buying replacement belts use ONLY ORECK genuine belts Belts other than ORECK belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings Using belts other than ORECK belts will void the warranty Lubrication The vacuum cleaner motor bearings are factory lubricated and seated Further lubrication is not required General Cleaner Care At least once a month check for and remove excessive lint string or hair from revolving brush Wipe the outside of the cleaner with a damp cloth Also clean the connector deflector assembly area base of cleaner and fan housing area If there is dust in the outer bag vacuum it or shake it out A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness CAUTION Wood Floors Soft Vinyl Asphalt Tile etc Floor Surfaces and Polished Floor Finishes Use floor and floor finish manutacturer s recommended methods of cleaning The metal stri
5. of this product oe the entire cost of any necessary servicing or repairs of any detects ORECK s liability for damages to you for any costs whatsoever arising out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase and ORECK shall not be liable for any direct indirect consequential or incidental damages arising out of the use or inability to use this product Some states do not allow the exclusion or limitation of incidental or conse quential damages so the above limitation or exclusion may not apply to you ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIOD AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THIS PERIOD Some states do not allow limitations on the duration of implied warranties so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state ACCESSORIES SOLD SEPARATELY USA 1 800 989 3535 CANADA 1 888 676 7325 ITEM PART NUMBER 1 Dust Bag 8 Pack Saniseal ACDS CCPK8DW Hypo Allergenic 2 Belts 3 Pack 0300604 3 Light Bulb 00965 0019 Fresh Air Tabs AIRTABS To Replace Filter Assembly To assist you in identitying components of your vacuum the parts have been numbered as
6. ORECK X SIMPLY AMAZING User s GUIDE XL2800H2 USA 1 800 989 3535 ri CANADA 1 888 676 7325 WWW ORECK COM VISIT ONE OF OUR CTO OVER 400 LOCATIONS HIGH SPEED UPRIGHT VACUUM CLEANER WITH Micro Seep CLEANING SYSTEM IMPORTANT SAVE THIS BOOKLET Includes e Safety Warnings e Warranty e Operating Instructions e Trouble Diagnosis e Accessories BEFORE OPERATING CLEANER READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY Table of Contents Table of Contents Important Safety Instructions page Maintenance Customer Service Warranty and Accessories page Assembly To Replace Paper Filter Dust Bag page Operating Instructions page How to Replace a Worn Belt To Adjust or Replace Brush page Bulb Replacement Stuffing or Blockage Using a Fresh Air Tab page Troubleshooting Guide page IMPORTANT SAFETY INSTRUCTIONS When using an electrical yuan basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not leave appliance unattended when plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not operate the unit while in the upright and locked position Do not let the unit run while in any one sta
7. follows Handle section upper Tube lower Power head Outer bag Paper filter dust bag 5 4 Power cord Retaining spring Bag tension bar Zip fastener On off switch Cord hook Plastic loop cable clamp Connector assembly Fan housing 15 Cord assembly WARNING Unplug cord from electrical outlet before servicing BAG REMOVAL 1 Unsnap bag door from base 2 Gently pull bag from cardboard collar upwards PPT POELLLETTITY RWN ODOOAONA aARWN 3 Dust seal will close automatically Before assembling appliance Remove two 2 BAG INSTALLATION screws from connector 1 Slide the cardboard collar assembly 13 Slide upper onto bag dock door until the handle section 1 over automatic closing dust seal matching section of the tab hole is locked in position connector assembly 13 aligning screw holes ee ae Finally insert screws in holes f a Connector and tighten firmly until handle is not loose AP eee eee eer errr kiddi PRESS HERE FIRMLY Ai TO SNAP in APPUYER FERMEMENT ICI POUR EMBOITER OPRIMA FIRMEMENTE AQUIPARA ENCAJAR A PRESION Machine should be in upright position when inserting cord assembly into loop Insert plug on cord assembly into handle Wrap power cord 6 around cord wrap 11 and cord wrap 13 and secure to U shaped part on plug 2 Firmly push bag dock door with both thumbs on indication point until
8. ing See illustration D Remove debris with long nose pliers a screwdriver or coat hanger 4 To reassemble check O ring on tube and replace if damaged Vacuum will not operate properly without the tube O ring Slide O ring to approximately 2 from base of tube Replace tube by first lining up slot at base of tube with inner tab inside fan housing Then reinsert tube and push down until the tube is seated Make sure O ring is in place against fan housing E opening Replace and tighten collar until collar locking tabs are locked in place See illustration E Make sure collar is not cross threaded on housing 5 Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system When that happens the blockage will be at the top of the system starting in the area where the dust bag connects to the connector assembly See illustration F F Connector Deflector NOTE f the above actions do not correct the problem contact an ORECK authorized service center or call the customer service center US 1 800 989 3535 CANADA 1 888 676 7325 IMPORTANT On plush and new carpets stuffing may occur due to excessive fuzz and loose cuttings in the carpet Stuffing could occur for the first few cleanings until all the loose material is removed Due to the high efficiency of the cleaner many older carpets will cause stuffing when the cleaner is first used on them Using A Fresh Air Tab
9. lammable explosive or toxic vapors are given off by oil base paint paint thinner some mothproofing substances or in an area where flammable dust is present Do not pick up toxic material such as chlorine bleach drain cleaner gasoline etc with this appliance SAVE THESE INSTRUCTIONS Household Use Only Polarized Plug Notice This product is equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact an electrician to replace the obsolete outlet Do not defeat the purpose of the polarized plug Maintenance and Customer Service Your ORECK vacuum cleaner is a product of precise engineering The motor bearings are permanently lubricated and should not be oiled If you require additional information or have problems with your ORECK appliance you may call ORECK customer service at In USA 1 800 989 3535 In Canada 1 888 676 7325 Please specify the model number and serial code number which can be found on the data plate on the back of the vacuum Save your sales or purchase slip Should your ORECK appliance require warranty service in the U S A present this slip to the Authorized Service Center as your proof of purchase date or in Canada call customer service ORECK
10. lt Replace brush if bristles do not extend beyond base plate Clear obstruction Change bag Return to Service Center for repair Check bearing seal Make sure words old or new match at each end ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SERVICE CENTER CALL CUSTOMER SERVICE HOT LINE US 1 800 989 3535 CANADA 1 888 676 7325 Whenever calling please be sure to have your model and serial number from data plate 2002 Oreck Holdings LLC All rights reserved All word marks logos product configurations and registered trademarks are owned and used under the authorization of Oreck Holdings LLC 75268 05 REV D 12 02 ECN R 6815
11. new belt over the motor drive shaft Place the opposite end of the belt on the top of the brush pulley and roll the belt around the pulley Using your thumb and finger rotate the belt on the pulley ensuring that the belt encircles the entire circumference of _ the pulley Replace the door by sliding it into the groove at the bottom of the housing Replace the hold down screw To Adjust or Replace Brush IMPORTANT Unless the brush is worn as indicated above both bearings must be in the new position When rotating both bearings must be in the old position Unmatched settings will cause damage to your machine WARNING Unplug cord from electrical outlet before servicing To determine if the brush is worn place a firm straight edge across the nozzle opening If brush bristles do not extend beyond base plate brush should be adjusted Remove the base plate by removing 5 screws Then remove the belt and brush roll from the housing Rotate both bearing assem blies at ends of brush roll to show old and replace in the holding channels in the housing NOTE The bearing assembly setting marked OLD has two bars II on the top of the assembly The one marked NEW has one bar 1 When rotating bearings make sure both bearing assembly settings are the same and face up when replacing the brush roll Reassemble the belt and the base plate and check bristle height above ba
12. p on the base of the cleaner could be damaged if used on concrete or abrasive surfaces and therefore cause damage to wood floors soft vinyl asphalt tile etc floor surfaces and polished floor inishes The roller brush may also scuff very soft finishes Do not operate the unit while in the upright and locked position Do not let the unit run while in any one stationary position for any period of time Keep the unit moving while in operation Celoco Hypo Allergenic Filter System The CELOC SMMS outer bag of your vacuum cleaner is high filtration medical material designed to filter the smallest of dust particles It is important that the inside of the outer bag be cleaned Vacuum the inside of the outer bag or hand wash turned inside out with warm water and air dry For best results the CELOC SMMS outer bag should be replaced once a year The CELOC layered disposable inner dust bag must be replaced once a month even if it is not full Change it more often if it is used in extremely dirty areas Increase the cleaning power of your vacuum by changing the How to Replace a Worn Belt WARNING Unplug cord from electrical outlet before servicing Remove the replacement belt from the storage channel Remove the door by removing the hold down screw located on side of power head Slide the door forward by prying open with a screwdriver or coin Remove the belt from the brush roll pulley and the motor drive shaft Loop the
13. s housing 5 WARNING Do not use your vacuum cleaner on damp or wet surtaces This will cause damage to the vacuum cleaner and is dangerous to the user Damage caused by use on wet or damp surfaces is not covered under warranty 6 REPLACE THE BELT EVERY 6 MONTHS 7 Change the disposable filter dust bag at least once a month even if it is not full The collected dust in the dust bag can cause odor attract moisture act as a breeding area and can affect the efficiency of the cleaner 8 DO NOT run the vacuum cleaner over cord The revolving brush could damage the cord Disposable Paper Filter Dust Bags Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner The purpose of the paper bag is to trap dirt but at the same time it must be porous enough to allow air to pass through If the paper bag becomes clogged no air can pass through the cleaner and cleaning cannot take place regardless of the cleaner s power Increase the CLEANING POWER of your cleaner by changing the bag often To keep your cleaner operating at maximum efficiency change the dust bag frequently DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG Be sure the disposable paper filter dust bag is installed properly All paper dust bags are not the same Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner and using bags other than genuine ORECK disposable bags will affect the
14. se plate at each end of brush If a previous adjustment has already been made and bristle height does not extend above base plate a new brush assembly should be ordered Bulb Replacement WARNING Unplug cord from electrical outlet before servicing e Remove lamp housing by removing two 2 screws in the the top of the lamp housing e Pull burned out bulb from holder and replace with new bulb Use only Oreck replacement parts e Replace lamp housing by replacing two screws in the top of the lamp housing Stuffing or Blockage Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly If your vacuum cleaner does not pick up properly or makes unusual noise and the outer bag does not fluff up or balloon open follow the following steps WARNING Unplug cord from electrical outlet before servicing 1 Check for blockage at the mouth of the intake opening See illustration A If there is blockage remove it with long nose pliers a screwdriver or coat hanger If you can not reach the blockage remove base plate See illustration B 2 If the blockage is not at the base remove lower tube See illustration C Unhook retainer spring releasing bottom of bag Twist lower collar counter clockwise to slide up Pull tube out of base Check for blockage If blockage is in the tube remove with a coat hanger 3 If tube is not blocked look into fan hous
15. tionary position for any period of time Keep the unit moving while in operation Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center or call customer service at US 1 800 989 3535 CANADA 1 888 676 7325 Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Do not run appliance over cord Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not use to pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without filter bag assembly in place Turn off all controls before unplugging Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or lighter fluid or use in areas where they may be present Do not use appliance in an enclosed space where f
Download Pdf Manuals
Related Search