Oreck XL U2007RH User's Manual
Contents
1. bags other than genuine ORECK disposable bags will affect the cleaning ability of your cleaner and could cause damage to it The Belt The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner If the belt becomes stretched or cut it will cause the revolving brush to stop completely or slow down See instructions in the manual for replacing belt An extra belt is stored in the baseplate of your cleaner When buying replacement belts use ONLY ORECK genuine belts Belts other than Oreck belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings Using belts other than ORECK belts will void the warranty E N G L I S H Lubrication The vacuum cleaner motor bearings are factory lubricated and sealed Further lubrication is not required General Cleaner Care At least once a month check for and remove excessive lint string or hair from revolving brush Wipe the outside of the cleaner with a damp cloth Also clean the connector deflector assembly area base of cleaner and fan housing area If there is dust in the outer bag vacuum it or shake it out A little preventative mainte nance will keep your cleaner looking new and will ensure continued cleaning effectiveness Cord Strain Relief The cord strain relief located on the upper section of the handle is des2. RLOW Essex U K CM19 5QE Please specify the model number and serial code number which can be found on the data plate on the back of the vacuum Save your sales or purchase slip Should your Oreck appliance require warranty service present this slip to the Authorized Service Center as your proof of purchase date Accessories ITEM PART 1 Dust Bag 25 Pack Saniseal ACDS Hypo Allergenic PK800025DW 2 Dust Bag 25 Pack Regular PK800025 Belts 3 Pack 0300604 Oreck Fresh Air Tabs AIRTABS IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire electric shock or injury Do not leave appliance unattended when plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not operate the unit while in the upright and locked position Do not let the unit run while in any one stationary position for any period of time Keep the unit moving while in operation Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water retu
3. UFACTURING COMPANY Oreck 21180 Johnson Road Long Beach MS USA 39560 gives you the following warranty for this product only if it was originally purchased at retail and not for resale from Oreck or an Oreck Authorized Retail Dealer Oreck will repair or replace free of charge to the original purchaser any part that is found to be defective in material or workmanship within one 1 year of the date of purchase This limited warranty covers the revolving roller brush for thirty 30 days from the date of purchase This warranty does not cover the replacement of expendable or consumable parts such as carbon motor brushes edge brushes belts bulbs disposable bags and other parts subject to normal wear unless they are defective in material or workmanship This warranty does not apply to any part subjected to accident abuse alteration misuse damage caused by act of God the use of voltages other than indicated on the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product Oreck s warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product If you purchase this product from any other source your purchase is AS IS which means Oreck grants you no warra
4. V AJA SO LZ77SZ ORECK XI SIMPLY AMAZIN G User s GUIDE COMMERCIAL U2007RH HIGH SPEED UPRIGHT VACUUM CLEANER WITH Microsweer CLEANING SYSTEM eIMPORTANT SAVE THIS BOOKLET Includes e Safety Warnings e Warranty e Operating Instructions e Trouble Diagnosis e Accessories me 4 Intake Opening Intake Opening c i E N G L I S H BEFORE OPERATING CLEANER READ ALL INSTRUCTIONS IN THIS MANUAL CAREFULLY Table of Contents Maintenance and Customer Service Accessories Important Safety Instructions page 3 Warranty Troubleshooting Guide page 4 Parts List Assembly Operating Instructions 5 page 5 To Replace Filter Dust Bag Using an Oreck Fresh Air Tab How to Replace a Worn Belt To Adjust or Replace Brush page 6 Stuffing or Blockage 0005 page 8 Maintenance and Customer Service Your Oreck vacuum cleaner is a product of precise engineering The motor bearings are permanently lubricated and should not be oiled If you require additional information or have problems with your Oreck appliance or to order new bags or spare parts you may call ORECK customer service at 0 01279 406995 or write to Oreck Commercial 21 Greenway Business Centre Harlow Business Park Greenway HA
5. ate Clear obstruction Change bag Return to Service Center for repair Check brush roll end cards Make sure words OLD or new match at each end ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SERVICE CENTER CALL CUSTOMER SERVICE HOT LINE 0 01279 406995 Whenever calling please be sure to have your model and serial number from data plate E N G L I S H Parts List To assist you in identifying components of your vacuum the parts have been numbered as follows Handle section upper Tube lower Power head Outer bag Paper filter dust bag Power cord Retaining spring Bag tension bar Zip fastener 10 On off switch 11 Cord hook 12 Plastic loop cable clamp 13 Connector assembly 14 Fan housing 15 Cord assembly 16 Handle Brace 17 Cord Strain Relief AN OO AON Assembly fig 1 Before assembling appliance remove two screws from the connector assembly Remove cardboard insert by pulling upward fig 2 Slide upper handle section over matching section of the connector assembly Place brace against handle and connector assembly aligning screw holes Insert short screw into top hole and long screw into the bottom hole then tighten firmly until handle is no longer loose fig 3 Attach cord to cord clip by pressing above and below clip ensuring the cord is fully rested in clip Operating Instructions Make sure the disposable
6. ause stuffing when the cleaner is first used on them If your vacuum cleaner does not pick up properly or makes unusual noise and the outer bag does not fluff up of balloon open follow these steps WARNING Unplug cord from electrical outlet before servicing fig 16 Check for blockage at the mouth of the intake opening If there is blockage remove it with long nose pliers a screwdriver or coat hanger If you can not reach the blockage remove baseplate fig 17 fig 18 If the blockage is not at the base remove lower tube Unhook retainer spring releasing bottom of bag fig 19 Twist lower collar counterclockwise to slide up Pull tube out of fan housing fig 20 Check for blockage If blockage is in the tube remove with a coat hanger fig 21 If tube is not blocked look into fan housing Remove with a coat hanger fig 19 To reassemble check O ring on tube and replace if damaged Vacuum will not operate properly without the tube O ring Slide O ring to approximately 2 from base of tube Replace tube by first lining up slot at base of tube with inner tab inside fan housing Then reinsert tube and push down until the tube is seated Make sure O ring is in place against fan housing opening Replace and tighten collar until collar locking tabs are locked in place fig 22 Make sure collar is not cross threaded on housing Reattach bag spring fig 18 fig 23 Many times blockage occurs due to a full dust bag causing d
7. igned to reduce stress on the cord at the base of the handle Should the power cord come loose from the cord strain relief it can be easily reattached To attach the power cord to the cord strain relief grasp the Cord Strain power cord approximately 12 Relief inches from the base of the Clamp handle Pinch power cord together and slide approxi mately 1 2 inches through the bottom hole in flat side of cord strain relief Carefully slide power cord loop over clamp on cord strain relief and pull excess until the power cord is tightly rested under clamp CAUTION Wood Floors Soft Vinyl Asphalt Tile etc Floor Surfaces and Polished Floor Finishes Use floor and floor finish manufacturer s recommended methods of cleaning The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces and therefore cause damage to wood floors soft vinyl asphalt tile etc floor surfaces and polished floor surfaces The roller brush may also scuff very soft finishes Do not operate the unit while in the upright and locked position Do not let the unit run while in any one stationary position for any period of time Keep the unit moving while in operation To Replace Filter Dust Bag WARNING Unplug cord from electrical outlet before servicing BAG REMOVAL fig 4 Hook bottom of bag collar opening under lip B of connector assembly Pull up on bag collar and snap over l
8. ip A of connector fig 5 Press on edges of bag collar to ensure bag is completely installed IMPORTANT Check to make sure bag collar is behind lips A and B If it is not dust will leak into outer bag When filter bag is in place close outer bag with zipper fastener Using An Oreck Fresh Air Tab fig 6 Your ORECK XL vacuum cleaner has a special ORECK FRESH AIR tab pocket This pocket is located inside the area where the disposable paper bag attaches to the intake tube Insert tablet in pocket if desired How to Replace a Worn Belt WARNING Unplug cord from electrical outlet before servicing fig 7 Remove the replacement belt from the storage channel fig 8 Remove the door by removing the hold down screw located on side of power head fig 9 Slide the door forward by prying open with screwdriver or coin fig 10 Remove the belt from the brush roll pulley and the motor drive shaft fig 11 Loop the new belt over the motor drive shaft Place the opposite end of the belt on the brush roll pulley Rotate the brush roll three 3 complete revolutions to ensure that no part of the belt is overhanging the end of the motor drive shaft fig 9 Replace the door by sliding it into the groove at the bottom of the housing fig 8 Replace the hold down screw and tighten To Adjust or Replace Brush WARNING Unplug cord from electrical outlet before servicing fig 12 To determine if the brush is worn p
9. irt to back down the air flow system When that happens the blockage will be at the top of the system starting in the area where the dust bag connects to the connector assembly NOTE If the above actions do not correct the problem contact an Oreck authorized service center or call the customer service center at 0 01279 406995 75227 05 REV A 2005 Oreck Holdings LLC All rights reserved All word marks logos product configurations and registered trademarks are owned 11 05 ECN R 8199 amp 8058 and used under the authority of Oreck Holdings LLC Printed in America
10. lace a firm straight edge across the nozzle opening If brush bristles do not extend beyond baseplate brush should be adjusted fig 13 Remove the baseplate by removing 5 screws fig 14 Remove the belt and brush roll from the housing fig 15 Rotate both bearing assemblies at ends of brush roll to show OLD and replace in the holding channels in the housing NOTE The bearing assembly setting marked OLD has no ribs on the top of the assembly The one marked NEW has several ribs When rotating make sure both bearing assembly settings are the same and face up when replacing the brush roll fig 12 Reassemble the belt and the baseplate and check bristle height above baseplate at each end of brush If a previous adjustment has already been made and bristle height does not extend above baseplate a new brush assembly should be ordered IMPORTANT Unless the brush is worn as indicated above both bearings must be in the NEW position When rotating both bearings must be in the OLD position Unmatched settings will cause damage to your machine E N G L I S H Stuffing or Blockage IMPORTANT On plush and new carpets stuffing may occur inside the intake tube and the lower assembly This is due to excessive fuzz and loose cuttings in the carpet Stuffing could occurs for the first few cleanings until all the loose material is removed Due to the high efficiency of the cleaner many older carpets will c
11. nty and that you not Oreck assume the entire risk of the quality and performance of this product including the entire cost of any necessary servicing or repairs of any defects This warranty is in addition to your statutory and other legal rights Troubleshooting Guide WARNING Unplug cord from electrical outlet before servicing SAVE SERVICE CALLS CHECK THESE FIRST e Is the disposable filter dust bag full e Are pores of filter dust bag clogged with powder or fine dust Is anything clogging the revolving brush lower tube intake opening fan housing or connector assembly opening e Is the belt in place and turning the brush e Are the brush ends in the proper location e Does the brush turn freely Are hair string or rug fibers wound around the brush DOES NOT PICK UP Nozzle or intake pivot clogged Belt is broken or stretched Brush is worn Bag tube clogged Bag pores are clogged with fine dust Impeller fan is broken Revolving brush is not even at both ends PROBLEM PossiBLE SOURCE AREAS TO CHECK CLEANER Not plugged in Be sure cleaner is WILL NOT RUN properly firmly plugged into wall outlet No electricity in Check electrical wall outlet source fuse or circuit breaker CLEANER Filter bag is full Replace filter bag See To Replace Paper Filter Dust Bag Clear obstruction Replace belt Replace brush if bristles do not extend beyond basepl
12. paper filter dust bag is in place DO NOT operate the cleaner without a paper filter dust bag Plug the power cord into an electrical outlet Press the On l OFF O switch on handle assembly when ready to operate Choose from the low and high speed settings by pressing the ON LOW I ON HIGH Il OFF O switch on handle assembly when ready to operate General Information The performance of your new cleaner greatly depends upon care and maintenance The instructions in this manual will guide you in performing basic care and maintenance To obtain the most satisfying years of service read the instructions and keep them handy for future reference Operating Recommendations This new ORECK XL High Speed Upright is one of the finest fastest and strongest units in its class You ll love the way it cleans gets under things and it s SO lightweight and easy to use The following are a few simple suggestions regarding its operation 1 When inserting a new disposable paper filter dust bag FIRST PUFF OUT and OPEN THE BAG 2 When the disposable filter dust bag is full REPLACE IT 3 If at any time the machine does not pick up properly or makes an unusual noise STOP OPERATION and service 4 Although your upright will pick up pins paper clips and other small objects it is recommended that these be removed from the floor before you vacuum Failure to do so may result in permanent damage to the motor suction fan and its ho
13. rn it to a service center or call customer service at 0 01279 406995 Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Keep cord away from heated surfaces Do not run appliance over cord Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from Openings and moving parts Do not use to pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without filter bag assembly in place Turn off all controls before unplugging Use extra care when cleaning on stairs Do not use to pick up flammable or combustible liquids such as gasoline or lighter fluid or use in areas where they may be present Do not use appliance in an enclosed space where flammable explosive or toxic vapors are given off by oil base paint paint thinner some mothproofing substances or in an area where flammable dust is present Do not pick up toxic material such as chlorine bleach drain Cleaner gasoline etc with this appliance Use caution when vacuuming over area rug edges and fringe SAVE THESE INSTRUCTIONS For Commercial Use E N G L I S H Warranty ORECK MAN
14. using 5 WARNING Do not use your vacuum cleaner on damp or wet surfaces This will cause damage to the vacuum cleaner and is dangerous to the user Damage caused by use on wet or damp surfaces is not covered under warranty 6 REPLACE THE BELT EVERY 6 MONTHS 7 Change the disposable filter dust bag at least once a month even if it is not full The collected dust in the dust bag can cause odor attract moisture act as a breeding area and can affect the efficiency of the cleaner 8 DO NOT run the vacuum cleaner over cord The revolving brush could damage the cord 9 Use caution when vacuuming over area rug edges and fringe Disposable Paper Filter Dust Bags Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner The purpose of the paper bag is to trap dirt but at the same time it must be porous enough to allow air to pass through If the paper bag becomes clogged no air can pass through the cleaner and cleaning cannot take place regardless of the cleaner s power Increase the CLEANING POWER of your cleaner by changing the bag often To keep your cleaner operating at maximum efficiency change the dust bag frequently DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG Be sure the disposable paper filter dust bag is installed properly All paper dust bags are not the same Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner Using
Download Pdf Manuals
Related Search