Oreck WS-7013U User's Manual
Contents
1. batteries 3 Replace the battery cover 4 Wait 10 minutes or until both the indoor and outdoor temperatures are shown on the indoor temperature station 6 5 The indoor temperature station should now show in the TIME LCD and temperatures in the INDOOR and OUTDOOR LCD s IL TIME A SETTING THE TIME SET MIN MAX 1 Press and hold the SET button for CH RESET 5 seconds 12h will appear in the TIME LCD 2 Press and release the MIN MAX button to select either 12h time am pm or 24h time 3 Press and release the SET button 2 times the hour will flash in the upper left corner 7 4 Press and release the MIN MAX button to set the hour 5 Press and release the SET button to move to the minute setting 6 Press and release the MIN MAX button to set the minutes 7 Press and release the SET button to activate the clock Note When in 12h mode there is only a PM display which appears under TIME If there is no display then it is in AM mode Make sure you set the time accordingly III UNITS OF TEMPERATURE MEASURE A SELECTING UNITS OF MEASUREMENT 1 Press and hold the SET button for 5 seconds until 12h or 24h appears in the TIME LCD 2 Press and release the SET button again F will appear in the TIME LCD 3 Press and release the MIN MAX button to shift between F and C 4 Press and release the SET button twice to2. between Fahrenheit and Celsius press and release the MIN MAX button b When you have your choice shown on the display press and release the SET button once 4 3 The hour will now be flashing a Press and release the MIN MAX button until the correct hour is shown Note When in the 12h mode PM is displayed under the word TIME during PM hours During the AM hours this area will be blank b When the correct hour is shown press and release the SET button once 4 The minutes will now be flashing a Press and release the MIN MAX button until the correct minutes are displayed Press and release the SET button once more to complete the setup DETAILED SETUP GUIDE I BATTERY INSTALLATION A REMOTE TEMPERATURE SENSOR ana 1 Remove the mounting bracket 2 Remove the battery cover 3 Observing the correct polarity install 2 AA batteries make sure they do not spring free or start up problems may occur Replace the cover 5 B INDOOR TEMPERATURE STATION Note After the batteries are installed DO NOT press any buttons This may interfere with the signals causing temperatures to register incorrectly feaa EM Battery Cover Remove the battery cover on the backside To do this push the cover upward and pull it out 2 Observing the correct polarity install 2 AAA
3. A 1 5V Station Indoor Temperature 2 75 x 92 x 4 3 in Station excluding table stand 90 x 23 6 x 110 mm Remote Temperature 1 57 x 0 9 x 5 04 Sensor 40 x 23 x 128 mm Battery life Approximately year WARRANTY INFORMATION Oreck Corporation warrants the Indoor Outdoor Clock and Weather Station WS 7013U free from defects in material and workmanship under normal non commercial use and service Oreck will remedy any such defects if they appear within one 1 year from date of purchase This warranty gives you specific legal rights and you may have other rights which vary from state to state FCC ID OMO 01RX Receiver OMO 01TX transmitter THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 14 USA 1 800 989 3535 CANADA 1 888 676 7325 WWW ORECK COM VISIT ONE OF OUR CD OVER 400 LOCATIONS 2002 Oreck Holdings LLC All rights reserved
4. ANY BUTTONS FOR 10 MINUTES In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor and outdoor temperature If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above After both the indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set the time The remote temperature sensor has a range of 80 feet and should be placed in a dry shaded area 3 Any walls the signal will have to pass through will reduce distance An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance Your distance plus resistance should not exceed 80 feet in a straight line NOTE Fog and mist will not harm your remote temperature sensor but direct rain must be avoided To complete the setup of your indoor temperature station after the 10 minutes have passed please follow the steps below 1 To set the time press and hold the SET button for 5 seconds Note A 12h or 24h will appear on the top line 12h for AM PM 24h for military time a To change between 12h and 24h press and release the MIN MAX button b When you have your choice shown on the display press and release the SET button once 2 Degrees Fahrenheit will now show a To change
5. WS 7013U Wireless 433 MHz Temperature Station Instruction Manual SET MIN MAX CH RESET Register your product on the web at WWW ORECK COM TABLE OF CONTENTS Topic Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Selecting Units of Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Mounting Troubleshooting Maintenance and Care Specifications Warranty Information INVENTORY OF CONTENTS 1 The indoor temperature station Figure 1 2 The remote temperature sensor TX6U and mounting bracket Figure 2 3 3 1 2 Philips screws 4 One strip of double sided adhesive tape 5 Instruction Manual and Warranty Card 6 2 AAA 1 5V batteries 7 2 AAA 1 5V batteries Figure 1 Figure 2 ua A on oe ADDITIONAL EQUIPMENT 1 Philips screwdriver not included QUICK SETUP Hint Use good quality Alkaline Batteries and avoid rechargeable batteries 1 Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart 2 Batteries should be out of both units for 10 minutes 3 Place the batteries into the remote temperature sensor first then into the indoor temperature station All remote temperature sensors must be started before the indoor temperature station 4 DO NOT PRESS
6. activate settings IV FEATURES A MINIMUM AND MAXIMUM a B pi TEMPERATURES Press and release the MIN MAX button MIN appears in the temperature LCDs and the recorded minimum temperatures are displayed Press and release the MIN MAX button to toggle to the maximum temperatures The time of occurrence of the value for outdoor temperature will also flash RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES To reset both the minimum and maximum temperatures press and hold the RESET button for 4 seconds V MOUNTING Note To achieve a true temperature reading avoid mounting in direct sunlight We recommend that you mount the remote temperature sensor on an outside North facing wall The sending range is 80 feet obstacles such as walls concrete and large metal objects will reduce the range Test the system by placing both units in their desired location 9 before permanently mounting A REMOTE TEMPERATURE SENSOR 1 Remove the mounting bracket from the remote temperature sensor 2 Mount using either screws or adhesive tape 3 Reattach the remote temperature sensor to the mounting bracket B THE TEMPERATURE STATION 1 The indoor temperature station comes with the table stand already mounted If you wish to use the table stand all that is required is to place the indoor temperature station in an appropriate location 2 To wall mount remove the table stand To do this pull d
7. as a heat sink to absorb and store heat from external sources i e handling of the case or radiant heat In addition the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range Error is usually greater at the extreme ends of a range making it harder to compare different ranges with different curves Under non laboratory conditions it is difficult to compensate for the above factors and obtain an accurate comparison MAINTENANCE AND CARE INSTRUCTIONS Extreme temperatures vibration and shock should be avoided to prevent damage to the units Clean displays and units with a soft damp cloth Do not use solvents or scouring agents they may scratch the displays and casings Do not submerge in water Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer Opening the casings voids the warranty Do not try to repair the unit 12 SPECIFICATIONS Transmitting 433MHz ren Indoor Temperature 32 F to 156 2 F with Station Indoor 0 2 F resolution 0 C to 69 0 C with 0 1 C resolution Remote Temperature 21 8 F to 156 2 F Sensor Outdoor 0 2 F resolution 29 9 C to 69 0 C with 0 1 C resolution Temp accuracy 1 F 4 5 C Transmitting range Maximum 80 feet 25m open space Indoor Every 10 seconds Outdoor Three times in 10 minutes Remote Temperature 2 x AA 1 5V Sensor Indoor Temperature 2 x AA
8. own on the stand from the rear and rotate forward a Fix a screw not included into the desired wall and place the indoor temperature station onto the screw using the hanging hole on the backside Gently pull the indoor temperature station down to lock the screw into place TROUBLESHOOTING NOTE For problems not solved please contact Oreck Customer Service at 1 800 989 3535 10 Problem The LCD is faint Solution Replace batteries Problem No outdoor temperature is displayed Solution 1 Remove all batteries reinsert into remote temperature sensor first and then into the indoor temperature station 2 Place remote temperature sensor closer to the indoor temperature station 3 Make sure all batteries are new 4 Place remote temperature sensor and indoor temperature station in position so the straight line signal is not passing through more than two or three walls Problem Temperatures do not match if units are placed next to each other Solution Each temperature sensor is manufactured to be accurate under normal conditions to within 1 degree plus or minus and so two temperature sensors could be as much as 2 degrees different However the difference can be exaggerated further because the temperature sensors are designed for different working environments The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display case In addition the case can act
Download Pdf Manuals
Related Search