Oreck STEAM-ALL STEAM200 User's Manual
Contents
1. e Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center or call customer service at US 1 800 989 3535 Canada 1 888 676 7325 e Do not pull or carry by the power cord use cord as a handle close a door on the power cord or pull the power cord around sharp edges or corners e Keep the power cord away from heated surfaces e Do not run the steam cleaner over the power cord e Do not use an extension cord e Turn off all controls before unplugging Always remove the power cord from the outlet and handle the steam cleaner with care when filling the boiler tank with water e Do not unplug by pulling on the power cord To unplug grasp the plug not the power cord e Do not handle the plug or appliance with wet hands e Do not over fill the boiler tank Do not exceed the maximum fill level Use the measuring jug to measure the correct amount of water e Do not use without the filler cap in place Check that the filler cap is completely screwed down before use e Do not operate without water in the boiler tank e Do not fill the water tank with anything other than water or Oreck Fresh Air Steam Mop Essence Never put additives such as perfume stain remover or products containing alcohol in the water as they may damage the steam cleaner or make it dangerous to use e Empty the boiler tank when the steam cl2. boiler tank with water 2 Place the filler cap on and shake vigorously to release lime scale deposits on the bottom of the boiler tank 3 Over a sink remove the filler cap and pour the water out De scaling the Boiler Tank A WARNING Do not fill the water tank with anything other than water or Oreck Fresh Air Steam Mop Essence Never put additives such as perfume stain remover or products containing alcohol in the water as they may damage the steam cleaner or make it dangerous to use Do not preheat unit when de scaling User should release pressure with the trigger any time they are cooling and removing the cap Switch the steamer OFF unplug the power cord and allow the steamer to cool off N Remove the filler cap and empty the water out Pour 25 fl oz 739 ml of de scaler solution into the tank Place the filler cap back on and swirl the solution around the tank oi Let the solution sit for thirty minutes o Empty the solution Wipe the traces of the solution off the steamer housing Troubleshooting Service problems that appear to be major can often be solved easily You can be your own troubleshooter by reviewing this guide All other servicing should be done by an Oreck Problem e Unit fails to steam e Heating indicator light does not illuminate power light is illuminated but unit fails to steam authorized service center Not plugged in
3. cap DANGER Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is grounded If not have a proper outlet installed by a qualified electrician This appliance is for use on nominal 120 volt circuit It has a grounding plug similar to the example shown Make sure the appliance is connected to an outlet with the same configuration as the plug No adapter should be used with this appliance Grounded Plug This appliance must be grounded If it should malfunction or break down grounding provides a safe path of least resistance for electrical current reducing the risk of electrical shock The cord for this appliance has an equipment grounding conductor and a grounding plug It must only be plugged into an electrical outlet that is properly installed and grounded in accordance with all local codes and ordinances SAVE THESE INSTRUCTIONS For household use only Parts Product Components Penoanron a h ee d Aa N O 15 16 17 Steam All Steamer Shoulder strap Handle hose Extension tube 3 Floor nozzle adaptor Floor nozzle Cotton floor towel Jet nozzle adaptor Jet nozzle Large brush Small brush Angled nozzle Upholstery nozzle Cotton Bonnet for upholstery nozzle Window squeegee Funnel Measuring cup Features Filler Cap
4. properly Household circuit breaker ground fault interrupter has tripped or blown a fuse Solution Be sure cleaner is firmly plugged into wall outlet Reset circuit breaker ground fault interrupter or replace fuse If you need assistance contact a licensed electrician Thermostat indicator light does illuminate but unit fails to steam Mineral build up in unit Unit may be suffering from internal mechanical problems See De scaling the Boiler Tank on page 19 Unplug unit and contact Customer support for repair or replacement assistance Steam output is weak or intermittent Mineral build up in unit It is normal for the unit to periodically stop steaming for a few seconds If steam stays off for longer periods follow the De scaling the Boiler Tank instructions on page 19 e Excessive gurgling in hose handle e Water drips from nozzle 20 e Water condensation in hose handle e Boiler has been overfilled e Some gurgling is a natural effect of the steaming process For excessive gurgling or dripping water point the nozzle towards the ground and shake to remove the excess water Empty some water out of the boiler so that is contains no more than 25 oz of water Replacement Parts All accessories and replacement parts are sold separately To order call our customer service group or visit our website Please have your model number from the data label on the
5. CULAR PURPOSE ARE LIMITED IN DURATION TO THE WARRANTY PERIOD AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED WILL APPLY AFTER THIS PERIOD Some states do not allow limitations on the duration of implied warranties so the above limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If appropriate see additional information for extended warranty 23 2010 Oreck Holdings LLC All rights reserved All marks text logo s product configurations and registered trademarks are owned and used under the authority of Oreck Holdings LLC 53539 01 REV A 09 10 ECN R 10091
6. ORECK Steam AlI Canister STEAM200 clean home Important Read this manual carefully and keep for future reference En o Thank You for purchasing our top of the line Oreck Steam All j y Canister Steam Cleaner This powerful environmentally friendly cleaner will help you clean both hard floors and refresh carpets At Oreck we understand that our customers are unique and expect superior service To meet your needs we offer different customer service options to accommodate your lifestyle and preference Welcome to our Call Click Visit customer service program To speak with an Oreck representative call click or visit using the information below USA 1 800 989 3535 Canada 1 888 676 7325 Call C gt k On the web point and click at www oreck com 1C or visit www oreck com and click locate a store on the top right Visit us in person at one our store locations Visit EEA To find the nearest store please call 888eoreck oo 1 888 673 2578 Contents General WarningS 00e cee eee 4 PAINS ea catch a satcitertaccase tary selects ashe EEE 7 Product Components 7 Features c2ccc0cn tee teda whiee eae cates ods 8 ASSEMDIY sc iis coe denae gave weedy de Ate oa 9 Attach the Hose Handle 9 Attach the Floor Nozzle 9 Attaching the Jet Adaptor to Nozzles 10 USC cave ccee cee ee ew eee eee eee eee ee 12 Choose the Attachm
7. and Boiler Tank The filler cap prevents steam from escaping from the boiler tank The boiler tank holds the water steam ON OFF Button Turns the steamer on and off Carrying Handle Used to carry the steamer and hold during use Hose handle button Used to control the direction of the steam and connect the attachments to the steamer Safety lock button Used to lock the trigger and prevent accidental release of steam n Steam trigger Used to apply steam Hose Release Button Releases hose Hose Inlet and Flap Hose connection location Thermostat Indicator Light Illuminates when steamer is turned ON and steam is building up Turns off when the correct steam temperature has been reached 10 Power Light Indicates steamer has been turned ON 11 Cord Storage Foot Use to wrap the power cord when storing the Steam AI Steamer Assembly A WARNING To reduce the risk of personal injury AN unplug the power cord from the electrical outlet and let the unit accessories cool down completely before handling Attach the Hose Handle 1 Pull the hose inlet flap down 2 Line up the keyway on the hose handle with the socket of the Steam All Steamer Tip 3 Push the keyway into the socket See page 12 to determine the correct attachments for your cleaning job Keyway on hose handle Plug Attach the Floor Nozzle 1 Position the floor nozz
8. bottom of the unit Number Accessories Four cotton floor towels two cotton STEAMKIT200 bonnets Replacement Parts Steam All Shoulder Strap 53547 01 Steam All Extension Tube 53548 01 Steam All Hose 53549 01 Steam All Floor Nozzle 53550 01 Steam All Upholstery Nozzle 53551 01 Steam All Window Squeegee 53552 01 Steam All Measuring Cup 53553 01 Steam All Jet Nozzle 53554 01 Steam All Funnel 53555 01 Steam All Jet Nozzle Adaptor 53556 01 Steam All Large Cleaning Brush 53557 01 Steam All Small Cleaning Brush 53558 01 Steam All Angled Nozzle 53559 01 Warranty Steam All Canister 22 ORECK MANUFACTURING COMPANY Oreck Manufacturing Company gives you the following limited warranty for this product only if it was originally purchased for residential use not resale from Oreck or an Oreck Authorized Retail Dealer Oreck will repair or replace free of charge to the original purchaser any part that is found to be defective in material or workmanship within one 1 year of the date of purchase This limited warranty applies to normal domestic use Any commercial use of this product will void this limited warranty This limited warranty does not cover the replacement of expendable or consumable parts such as towels bonnets and other parts subject to normal wear unless they are defective in material or workmanship This limited warranty does not apply to any part subjected to a
9. ccident abuse commercial use alteration misuse damage caused by act of God the use of voltages other than indicated on the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product Oreck s limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product If you purchase this product from any other source your purchase is AS IS which means Oreck grants you no warranty and that you not Oreck assume the entire risk of the quality and performance of this product including the entire cost of any necessary servicing or repairs of any defects Oreck s liability for damages to you for any costs whatsoever aris ing out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase and Oreck shall not be liable for any direct indirect consequential or incidental damages arising out of the use or inability to use this product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTI
10. eaner is not in use e Do not touch any hot areas on the steam cleaner or accessories Allow them to cool down before handling them e The force and heat of the steam may have an adverse effect on some materials Always test the steamer on a small concealed area to determine if it is suitable for treatment e Never point or aim the steam cleaner at people animals risk of scalding plants electrical systems or wires e Do not use to treat clothing being worn on the body e Connecting the steam cleaner to improper voltage may result in damage to the steam cleaner and possible injury Always plug the steam cleaner into a power outlet with the correct voltage See the rating label on the unit for the correct voltage e Putin storage after each use to prevent tripping accidents e Steam through the hose and handle may cause them to get hot Avoid contact with hot areas WARNING This steamer product is equipped with a safety locking filler cap The red button located in the center of the cap will rise above flush with cap when the system is heating and under pressure This will prevent the user from removing the cap Do not defeat the safety mechanism Turn the unit OFF and depress the trigger to relieve pressure Do not attempt to remove the cap and fill the tank until you have relieved as much pressure as possible and the unit has cooled or the red button returns to its original position Always use caution when removing the
11. eegee Squeegee Squeegee clip i tal To attach the cotton floor towel to the floor nozzle 1 Lift the clip on the top of the Floor nozzleclip floor nozzle 2 Place the cotton towel under clip and release 3 Repeat steps one and two for the opposite clip on the floor nozzle To attach the shoulder strap If you would like to use the shoulder strap 1 Attach the hooks on the strap to the plastic rings on the Steam All 2 Adjust for comfort by sliding the strap length adjuster W s Strap length adjustor Use Choose the Attachments To determine the right tool the for the job you must first choose the correct adaptor nozzle and accessory Adaptors Extension Tube Use for additional reach There are three extension tubes to extend your reach an additional forty inches Floor Nozzle Adaptor Attaches to the Floor Nozzle Jet Nozzle Adaptor Attaches to the Jet Nozzle and Upholstery Nozzle Nozzles and Their Accessories Floor Nozzle The floor nozzle is used for cleaning large floor areas Floor Nozzle Accessories Cotton Towel Cleans sensitive surfaces such as sealed wood and linoleum Upholstery Nozzle The upholstery nozzle is used for cleaning cushions carpets and car seats Upholstery Nozzle Accessories Squeegee Cleans glass surfaces mirrors ceramic tile and other non porous surfaces Important Sudden application of excessive heat may shatter glass see Safety Warning o
12. ents 12 Aapo S eeraa E eed eens 12 Nozzles and Their Accessories 12 Before You Begin Cleaning 13 Apply Steam 0 0 cece eee 16 After Using the Steamer 18 Maintenance 000 0c eee eee eee 19 Rinsing the Boiler Tank 19 De scaling the Boiler Tank 19 Troubleshooting 0200 20 Replacement Parts 0005 21 Wattanly vicctcava coteada bie sein whois 22 Safety General Warnings AX IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using the steam cleaner WARNING To reduce the risk of fire electric shock or injury when using an electrical appliance basic precautions should always be followed including the following e Do not leave appliance unattended when plugged in Unplug from outlet when not in use and before servicing e To prevent shock do not use outdoors The steam cleaner is intended for household use only e Do not let the unit run while in any one stationary position for any period of time Keep the unit moving during use e Do not allow to be used as a toy e This product is not to be used by children e Do not use the steam cleaner directly overhead e Do not put any objects into openings or operate with openings blocked e Never immerse the steam cleaner in water or liquids e Use only as described in this manual Use only manufacturer s recommended attachments
13. ight to ten inches 2 Apply steam to clean the glass at a distance of four to six inches oo Switch the steam OFF and wipe the moisture off the glass top to bottom with the window squeegee Wipe the squeegee and lower edge of the glass Dry after each pass Bedding and Upholstery 1 Attach the upholstery nozzle 2 Pass the steam slowly and evenly over the surfaces ensuring all areas are cleaned 3 Repeat the process in a cross pattern 4 Allow the mattress or furniture to dry before covering with bedding or covers e To clean very dirty areas move the nozzle slowly across the surface Cleaning Tl PS e Turn the cloth and change regularly to optimize cleaning power of the cloth After Using the Steamer N O Switch the steamer OFF unplug the power cord and allow the steamer to cool off Press the steam trigger and release any steam pressure Engage the steam safety lock button Remove the filler cap Empty the boiler tank and allow the tank to dry before placing the cap back on Press the hose release button and release the hose Wrap the cord around the cord storage foot and storage release lever For quick release of the cord rotate the storage release lever Maintenance Rinsing the Boiler Tank A WARNING To reduce the risk of personal injury unplug the power cord from the electrical outlet and let the unit accessories cool down completely before handling 1 Fill the
14. is steam pressure in the boiler and go back in when it is safe to refill the boiler tank Do not attempt to remove the cap when the indicator is pushed out Turning the unit off and depressing the trigger will assist in reducing pressure in the system lock button gaat 1 Insert the power plug into a polar Thermostat indicator light Filler cap ON OFF button ized electrical outlet 2 Check the filler cap is seated properly and tight 3 Engage the trigger lock by pushing the safety lock button on the left side of the hose handle 4 Press down on the ON OFF button The power and thermostat indicator will illuminate Important Turning the unit off and depressing the trigger will assist in reducing pressure in the system It takes approximately five minutes to reach the correct temperature The thermostat indicator light turns off when the correct temperature has been reached Tip Filling the unit with hot water will reduce the preheat time Apply Steam A WARNING To reduce the risk of personal injury unplug the power cord from the electrical outlet and let the unit accessories cool down completely before handling Hot water may be ejected at start up and possibly cause serious injury if in contact with body parts Always direct the steam into a cloth bucket or sink until the steam is emitted evenly The steam may cause serious injury if in contact with body parts Ne
15. le adaptor so the tube portion is pointing down 2 Insert floor nozzle adaptor into the floor nozzle and rotate the adaptor so the tube is now pointing up 3 Pull on the floor nozzle adaptor to make sure it is locked 4 Place the floor nozzle assembly on the hose handle or extension tube until they are locked together You will hear a click and the yellow interlock should be in the hole on the attachment Extension tube UN A en Floor nozzle assembly Floor nozzle Floor nozzle adaptor tube Attaching the Jet Adaptor to Nozzles Note The jet adaptor is used when attaching the upholstery nozzle and jet nozzle 1 Align the keyway on the jet nozzle adaptor so it is lined up with the key in the nozzle 2 Insert the jet adaptor into the nozzle of choice and rotate so the two are locked together 3 Insert the assembly into the hose handle or extension tube until they are locked together You will hear a click and the yellow interlock should be in the hole on the attachment Jet Nozzle Jet Adaptor Release button Upholstery Yellow interlock button Nozzle Attaching the Accessories To attach the window squeegee to the upholstery nozzle 1 Slide the two tabs on the upholstery nozzle under the two tabs on the Upholstery window squeegee Nozzle tabs N Rotate the upholstery nozzle forward until it engages with the front clip of the squ
16. n page 17 Large Cotton Bonnet Cleans sensitive surfaces Jet Nozzle Cleans multiple surfaces such as stainless steel and enamel Jet Nozzle Accessories Brushes Best for removing stains Angled Nozzle Use for hard to reach areas such as corners blinds radiators and toilets Before You Begin Cleaning A WARNING To reduce the risk of personal injury unplug the power cord from the electrical outlet and let the unit accessories cool down completely before handling Steam may cause serious injury if in contact with body parts Always allow the steamer to cool down before handling Do not fill the water tank with any thing other than water or Oreck Fresh Air Steam Mop Essence Never put additives such as perfume stain remover or products containing alcohol in the water as they may damage the steam cleaner or make it dangerous to use Fill the Boiler Tank 1 Unplug the power cord and remove the filler cap by pressing down and turning it counter clockwise 2 Using the measuring cup and funnel fill the boiler tank The boiler tank can hold twenty five fl oz 739 ml Do not overfill oo Replace the filler cap on the boiler tank Cleaning Tips Using warm water will reduce heat up time and risk of spitting out water during start up Important The filler cap is a safety feature and must be properly seated and closed before generating steam 13 Refilling
17. the Boiler Tank A WARNING To reduce the risk of personal injury unplug the power cord from the electrical outlet and let the unit accessories cool down completely before handling Steam may cause serious injury if in contact with body parts Always release all steam pressure before removing the filler cap Safety lock 1 Press the steam trigger and release all the steam pressure 2 Allow the steamer and assembly to cool down 3 Refill the boiler tank see Filling the Boiler Tank on page 13 Important If the boiler tank is dry turn the steamer OFF and allow it to A cool down until the red indicator on the filler cap has gone back in It is now safe to refill the boiler tank Do not attempt to remove the cap when the indicator is pushed out Steam trigger Connect the Hose Handle and Attachments 1 Choose the adaptor nozzle and accessory needed for your cleaning job 2 Follow the assembly steps as described on page 9 to assemble the Steamer in the configuration that you need Left safety Turn the Steamer ON A WARNING Steam may cause serious injury if in contact with body parts Ensure the filler cap is seated properly and tight and the safety lock button on the hose handle is engaged before turning the steamer ON Always direct the trigger away from the user and away from any bystanders Important The red indicator on the filler cap is a safety device It will push out when there
18. ver point the steamer at people or pets when in use Always turn the steamer OFF and unplug when the steamer is not in use NOTICE e Using the steamer on objects or surfaces that cannot resist extreme temperatures ie unsealed wooden surfaces laminates plastics delicate materials may cause damage Always check with the manufacturer if there is a doubt about using the steamer on a surface or fabric e Do not concentrate steam in one place for an extended period of time This may damage the surface or fabric Always test a hidden area before using steam on any surface or fabric 1 Disengage the trigger lock by pushing the safety lock button on the right side of the hose handle Right safety lock button 2 Test how the steam will effect the surface or fabric Cleaning TIP 3 Press and hold the steam For more control of j trigger Direct the steam at the the steam temperature Y surface to be cleaned Remove and cleaning power move Z the dirt by moving the steam the handle closer to or farther away from the surface being cleaned jet backwards and forwards over the area Steam trigger 4 Release steam trigger to stop the steam jet Cleaning Glass Surfaces A WARNING Sudden application of excessive heat may shatter glass and cause serious injury Always warm glass surfaces gradually when applying steam to the glass 1 Warm the glass by applying the steam evenly to the glass from a distance of e
Download Pdf Manuals
Related Search