Optoma Technology Panoview Graywolf II User's Manual
Contents
1. Panoview MOTORIZED CINEMA SCREEN GRAYWOLF II CINEMA WIDE SCREEN Optoma Technology Inc http www optoma com Panoview Hl NO 1 IMPORTANT SAFETY INSTRUCTIONS Basic safety precautions including the following should always be followed O Close supervision is necessary when any motorized screen is used by or near children do not leave motorized screen unattended while in use Do not operate motorized screen with damaged cord or if the motorized screen has been dropped or damaged until it has been examined by a qualified service technician Position the cord so that it will not be tripped over pulled or in contact with not surgaces Never yank cord to pull plug form outlet aways grasp plug bu head and pull to disconnect Let appliance cool completely before putting away Loop cord loosely around appliance when stoing O To reduce the risk of electric shock do not immerse this motorized screen in water or other liquids NE Panoview NO 2 e To reduce the risk of electric shock do not disassemble this appliance only a qualifid service technician may service or repair motorized screen Incorrect reassemble can cause electric shock when the motorized screen is used e Only use accessory attachment recommended by the manufacturer Use of non manufacturer recommended acces sory attachments may viod the screens warranty and release Panoview of all liability O Basic electrical safety precautions should always b2. e observed e in the event the above mentioned safety precautions are not observed The warranty may be viod and Panoview released of all liability Panoview HN NO 3 Thank you for choosing Panoview screens All screens have passed the strict quality inspection before delivery Read this manual carefully to ensure proper usage Important Attention the installation of the screen the electric wire connection the setting of the limit switches must be made by a trained engineer only SWITCH JACK 12V TRIGGER Motorized screen with IR remote control switch control amp 12v trigger port NA Panoview NO 4 Technical data Input Voltage 110VAC 60HZ Output Voltage 3A Fuse 1A IR Remote Control Distance lt 8m 15 Horizontal 12V Trigger Jack OD3 4xID1 3 12V Trigger Signal Voltage 7 11VAC or 8 16VDC Current 22mA IR Handset 1pc Switch control 1pc Unpack screen carefully be sure screen is in good condition and check that all accessories are included inside carton Care in mounting and care in correct operation will mean a long and satisfactory life for your Panoview screen Locate the screen where the audience can best see it and where other fumishings in the room permit Check that voltage and frequency marked on screen is in accordance with local power utility It is suggested only to use screen indoor under normal temperature and humidity conditions Panoview HN NO 5 Remove two
3. pulling locks on the bottom slat bar after the case has been installed Install screen brackets onto ceiling or wall with appropriate hardware MOUNT SCREEN TO WALL MOUNT SCREEN TO CEILING ME Panoview NO 6 ELECTRIC CONNECTION Internal wiring has been completed at the factory No addi tional wiring is necessary Note all wiring related to the screen may only be serviced by a manufacturer approved trained electrical technician Tampering with electrical wiring may void warranty and release Panoview of liability BLACK DOWN RED UP WHITE MOTO BLACK FUSE C250 R400 L G N z se PLUG ti 5 174 9 a AC120V 60HZ 3 E MICRO fp a WHITE gt ES q ED LJE GRO E MICRO J49 Panoview Hl NO 7 SWITCH Nes Os RED i i TOP1 i RED i N O tuje i BLACK H BLUE j BLACK JACK4 OPERATING INSTRUCTION Plug in power supply For Switch control Plug in Switch into switch jack Press button to Up position screen goes up Press button to stop position screen stops Press button to down position screen goes down For IR Remote Direct the handset to IR window on screen housing Press the Up Stop Down button on the hand
4. set screen goes Up Stop Down accordingly ME Panoview NO 8 For 12V trigger Input 12V trigger signal screen goes down Stop this signal screen goes up Electric lock Press the Up amp Down buttons on the IR handset together then all Up amp Down buttons on the switch and IR handset will be locked To be unlocked press Stop button on the IR handset again or unplug the power supply and plug in again Keeping the screen rolled in its protective case when not in use Always examine both front and back of surface before re rolling into case to make certain screen is free of dust dirt or other foreign matter
Download Pdf Manuals
Related Search