Optoma Technology BX-AL133 User's Manual
Contents
1. 9V DC In 12V Trigger Out 12V Trigger In 8 Button Remote Control Remote IR Sensor In 16 5V DC Power Supply For more information please visit our website at http www OptomaUSA com User s Manual 4 User s Manual BX AL133 Pian Your Installation The lens assembly may be mounted in one of two ways 1 To the ceiling or projector mount above the projector 2 Toa shelf or table below the projector that is attached to ceiling joists or studs Sheetrock embedded fasteners can and will become loose When attaching the motor assembly to the ceiling use a board plate or lens enabled projector mount A with repeated lens movement causing the mechanism to fall resulting in possible severe injury Planning for Projector Exhaust Some projectors have hot air exhaust ports that discharge from the front Avoid situations where the lens or housing will block or obstruct the warm air flow out of the projector as damage to the bulb and or the lens may result You can mount the sled either to the left or right of the lens During setup you can easily configure the lens in position to be on the motor housing or pulley housing side of the sled See Setup Changing Orientation of Logo Plate Optional The lens sled is configured for ceiling mounted operation as shipped As such the logo reads right side up with the mounting bar on top If you are using the sled in a table or shelf moun2. 2 Verify centering Press LENS IN and see where the lens stops If needed make small adjustments or a quarter inch to the lens bracket after disconnecting the power by loosening the screws and sliding the bracket to the left or right as needed to achieve centering 0 5 Gap E Reconnect the power and check g g l 2 the centering The optical sensors j Hl at will stop the edge of the lens a adaptor plate approximately a half Optoma inch from the housing on either side Oe of the sled You can use this gap mueeoeieee on the motor or the pulley side for fine tuning adjustments For more information please visit our website at http www OptomaUSA com User s Manual 8 User s Manual BX AL133 3 Attaching the lens to the bracket Attach the Optoma BX AL133 anamorphic lens to the bracket using the plastic knobs supplied with the lens Adjust the anamorphic lens vertically for correct alignment When the image is correct tighten the knobs against the bracket Using the remote test run LENS IN and LENS OUT commands Oo Optoma il f Tighten Knobs 4 Configuring the lens speed The lens has two operati
3. The Optoma system is built and tested in the USA with the strictest quality standards and certifications Features and benefits Easy straight forward installation and operation Machined high grade anodized aluminum components Repeatable precision positioning system Flexible mounting options for either table top or ceiling mount Speed selector for high or low speed operation Configurable lens in position Extra external IR sensor for remote mounting if needed Input 12V jack for automatic lens trigger Output 12V jack for screen masking trigger Non mechanical long life optical stop sensors Dry operating precision linear bearings u Heavy duty high precision NEMA 23 stepper motor Custom built low noise stepper drive circuitry and firmware Endurance tested to more than 250 000 traversals 8 button long range up to 50 feet remote control with discrete functions Backlit logo with on off lighting control Reversible logo plates Built and tested in the USA a FCC CE and UL certified For more information please visit our website at http www OptomaUSA com User s Manual 3 User s Manual BX AL133 Getting to Know Your System Motorized Sled Status LED Infrared Remote Sensor Mounting Plate Rail Drive Belt Rail Bearing X4 Lens Adaptor Plate Pulley Housing Cover Motor Housing Cover i c Remote IR Sensor Rear Panel View is
4. damp cloth make sure not to drip any water into the enclosure The sled internal drive is permanently coated to run smoothly Keep the rail linear bearing clean dry and contaminant free In case of accidental debris and or liquids spilled onto the system you can clean all contaminants with water and wipe down with denatured alcohol The drive mechanism relies upon a clean rail to operate smoothly The linear bearing and all enclosed bearings are constructed of specialized material to ensure smooth operation Remove power source before cleaning Outside lubricants will gum up the mechanism and possibly produce a film across the projector and anamorphic lens A Never use lubricants of any nature on any part of the mechanism For more information please visit our website at http www OptomaUSA com User s Manual 12 User s Manual BX AL133 Specifications Electrical Characteristics Model Power Supply Power Supply Output Operating Voltage Operating Current Draw Standby Current Draw Trigger Jack Remote IR Jack Remote IR Receivers IR Range IR Carrier Frequency Batteries Certification Design Life Optoma BX AL133 Motorized Sled 110 120v 50 60 Cycles 9V DC 0 5A 9 18V DC 0 5 1 5A Typical 650mA max 1 2A 60mA 3 5 mm Mono or Stereo Jack 12V Tip Positive 2 5 mm Stereo Jack Supplied 30z IR Emitter 2 One Fixed Another Remotely Attached Optional 50 ft from IR Sensor 38 kHz 2
5. from the ceiling and the ceiling mount adapter plate Position the ceiling mount adapter plate over the lens plate and the projector Line up the holes of the lens plate labeled holes for projector and ceiling mount in the diagram above with the holes of the ceiling mount and projector Install the silver screws from the attachment parts bag purchase the longest metric M4 screws without exceeding the depth of the projector f Ceiling mount hardware may vary If the provided screws are not long enough mounting holes for the greatest security 3 MOUNT PROJECTOR ASSEMBLY Securely connect the ceiling mount adapter lens plate and projector assembly to the ceiling mount and then adjust the ceiling mount to provide the proper 16 9 image orientation in the center of your 2 35 1 screen For more information please visit our website at http www OptomaUSA com User s Manual 16 User s Manual gt G7 AN ig Be BC 4 INSTALL CHAINS Hold the chain to the ceiling so that one end of the chain hangs just above one of the installed plate hooks Mark the ceiling location and repeat for the other chain hook Procure and install the ceiling hooks at those locations small enough to accept a chain end and strong enough when installed to support approximately 40 pounds or more The type of hook and method of installation may depend on the type of ceiling you have Cut the chain to make chain segments The ones that come closest to supporting
6. mask the side of the screen when an HDTV 16 9 image is being projected instead of a widescreen 2 35 1 DVD movie format The Trigger Out jack tip positive operates as follows OV Lens is in the LENS IN position H12V Lens is in the LENS OUT position Each sled is supplied with an optional remote IR sensor which may be used to improve reception if the sled is located where IR signals cannot be reached It may also be used with an IR repeater system by simply taping the remote sensor to one of the IR emitters from the repeater system To use simply peel off the included self S stick tape affix to a es es ees see Maser aystem convenient location RATAR i cd a and plug the 2 5 mm cable into the appropriate jack in the back of the unit anere 12V Trigger In poe From projector we f or scaler Remote IR Sensor In eo For more information please visit our website at http www OptomaUSA com User s Manual 11 User s Manual BX AL133 Cleaning and Maintenance The Optoma BX AL133 anamorphic lens system is maintenance free It will deliver many years of trouble free service as delivered from the factory To clean Lightly blow off any surface debris from the lens If needed clean the lens using standard cleaning supplies while the projector is on be careful not to look directly into the light beam of the projector Clean the metal components with a
7. the LED and moving the lens to the new LENS OUT position the opposite side LENS IN Commands the lens to move into the LENS IN position as configured in Setup PANEL OFF Turns the logo backlight off PANEL ON Turns the logo backlight on SLOW Sets the acceleration deceleration and maximum speed for slow low inertia traversal FAST Sets the acceleration deceleration and maximum speed for rapid traversal For more information please visit our website at http www OptomaUSA com User s Manual 10 User s Manual BX AL133 Rear Panel Triggers and Sensors To use the automatic lens trigger your projector or scalar must be equipped with a lens trigger and a standard double ended 3 5 mm 1 8 inch male mono or stereo jack cable Simply plug the cable into the projector s lens trigger jack and into the sled 12V Trigger In jack Follow the projector or scalar instructions to configure the lens trigger The Trigger In tip positive operates as follows 12V LENS IN command OV LENS OUT command NOTE The input trigger jack may be temporarily overridden by the remote control When the next transition of voltage occurs up or down the trigger will take control once again Another option allows you to use the 12V Trigger Out jack on the rear of the device The output jack is set to 12V whenever the sled is in the LENS OUT position This is typically used for triggering screen masking systems to
8. the lens plate when attached to the chain ends should be the ones that are attached to the plate and ceiling hooks Install the lens chains and adjust the nuts on the plate hooks to make the chains tight but without raising the front of the plate Tighten the plate hook nuts to compress the lock washer in the plate hook assembly 5 MOUNT THE ANAMORPHIC LENS INSTALLATION WITHOUT THE MOTORIZED MOUNT a Remove the lens from its lens bracket b Orient the lens bracket to the lens plate so that the angled sides of the lens bracket are toward the back of the plate Install the four lens mount assemblies large assemblies with white spacers from the top down through the four holes that are for the lens in the order of screw flat washer lens plate white spacer lens bracket flat washer lock washer and nut Use the hex key to tighten the nuts so that the lens mount assemblies are centered in the elongated lens bracket holes c Turn the projector on and project a full yet still 16 9 image from the projector Carefully install the lens and adjust the tilt to equalize the top and bottom image geometry while positioning the lens vertically to center the output beam Tighten the lens knobs INSTALLATION WITH MOTORIZED MOUNT a Do Not Connect the Power of the Motorized Mount at this Time b Position the motorized mount on the bottom side of the lens plate so that the six holes refer to the diagram on the previous page in the lens plate lin
9. AAA for Remote FCC CE BX AL133 Motor Drive Unit UL Class II Power Supply Only Greater than 250 000 rail traversals Physical Characteristics Weight Dimensions For more information please visit our website at http www OptomaUSA com 5 lbs See accompanying drawings User s Manual 13 User s Manual BX AL133 Dimensions ee 19 675 Score Mark Score Mark Motor Side Pulley Side For more information please visit our website at http www OptomaUSA com User s Manual 14 User s Manual BX AL133 Warranty Optoma Technology Inc warrants this product to be free of defects in original workmanship and material for a period of twenty four 24 months from the date of purchased During this period a defective unit may be repaired or replaced at the discretion of Optoma Technology Inc by returning it in its original packaging with a copy of your receipt This warranty does not cover damage resulting from tampering lack of prudent care accident or misuse including contravention of cautions stated in the instructions or any cosmetic damage not reported within fifteen 15 days of purchase All liability for damage is limited to the cost of the product and does not include incidental injury or peripheral damage to other equipment persons or property Optoma Technology Inc is not responsible for personal injury resulting from faul
10. Optoma BX AL133 Anamorphic Lens lt Optoma User s Manual User s Manual AN iis Fe Fe 1 Read and understand instructions and heed warnings before beginning installation 2 Mount rail securely The lens is heavy and requires a secure and stable surface Fasteners in sheetrock alone are not safe Reciprocal lens motion can and will work them loose Use a board plate or projector mount fixed to ceiling joists or studs 3 Anticipate unexpected lens motion A malfunction can cause the lens to move unexpectedly Disconnect the power when installing working on or repositioning the lens While on a ladder do not stand in the direct path of the lens in case of unexpected or accidental movement 4 Do not install the lens in a wet or moist environment or where the mechanism will be exposed to extreme or external weather conditions The lens is for indoor use only 5 Never pour any liquid or push any object into the enclosure 6 Do not install in direct path of heater vents or projector exhaust ports Do not block any of the vents or holes in the enclosure 7 The power adaptor is intended for 100 220 volt 50 60 cycle AC power only 8 Do not subject power cord to conditions which will wear through or cut the insulation Avoid excessive tension or chafing of the cord 9 Do not service the motor drive or electronics There are no user serviceable parts Contact your dealer or send to a factory approved facili
11. S 9000 0000C0CCOCOOOC O 9000 0000C0CCOCOOCC E 0000000000000000 0000000000000000 00000000000000 0000000000020 000000 00000 0000 0000 0000 0000o 00000 eee Milpitas CA 95035 USA 715 Sycamore Drive Tel 408 383 3700 USA Fax 408 383 3702 www OptomaUSA com Optoma Technology Inc 715 Sycamore Drive Milpitas CA 95035 Tel 408 383 3700 Fax 408 383 3702 For more information please visit www Optoma com Optoma Specifications subject to change without notice Copyright 2007 Optoma Technology Inc
12. ation please visit our website at http www OptomaUSA com User s Manual 7 User s Manual BX AL133 Setup 1 Power up the sled and set LENS IN position Slide the lens into the middle of the sled before powering up Plug the power adaptor into an AC outlet then into the back of the unit as illustrated Using the remote press the lens in button The lens sled will slowly position itself into the factory default LENS IN position The edge of the adaptor plate will land about a half inch from the motor housing side of the sled If the bracket is in front of the projector lens proceed to the next step Verify centering If the bracket is not in front of the projector lens you will need to change the setting Simply press the LENS OUT button on the remote and wait for the bracket to move in front of the projector lens Press and hold the LENS OUT button again for 5 seconds The sled will confirm the new setting by moving the bracket away from the projector lens to the new LENS OUT location The edge of the adaptor plate will land about a half inch from the motor housing side of the sled You have now re programmed the sled This setting will be preserved in the unit even if it is unplugged or undergoes a power failure To change back just repeat the above procedure Rear Panel View i CI 9V DC In 12V Trigger Out 12V Trigger In Remote IR Sensor In e
13. e up with the six holes in the flat side of the motorized mount Insert the four small 1 4 screws through the four small holes of the lens plate into the motorized mount and tighten c Insert the sled safety assemblies through the remaining two holes from bottom up in the order of screw motorized mount lens plate washer lock washer and nut Tighten both safety assemblies d Refer to the motorized mount user manual for additional instructions at this time ceiling Periodically check all fasteners and connection hardware to be sure they have not come loose Improper installation may lead to an increased risk of your equipment i Use extreme caution and appropriate hardware when installing heavy objects to a becoming unstable and possibly causing injures For more information please visit our website at U SM 11417 http www OptomaUSA com ser s Manua User s Manual BX AL133 Addendum The Finished Product For more information please visit our website at http www OptomaUSA com User s Manual 18 Canada 5630 Kennedy Road Mississauga ON L4Z 2A9 Canada Tel 905 361 2582 Fax 905 361 2581 ee riyi 2 LAAJ a 00o E rx yi rx yy 0000 0000o wT TT e8ecece x Cee ATLITI 0000 LILII M we 2OCCCC e C9OOCOCOCOCOCOSO uvu meee XY OXY TY YD 0000000 OCOCOCOCOCO 000 00000000000 000000000 0000000000000000 000O 0000 000000000 0000000 000 COCCCCCR O00000 CO COSCCCCOOCOCOOCCO
14. et to the lens adaptor plate Then only after properly aligning and positioning the bracket power up the sled and check the alignment again Finally attach and adjust the lens to its correct angle and vertical position Follow this procedure 1 Line up the center line of lens There are score marks on the back of the mounting bar that correspond to the center of the BX AL133 expansion lens Before starting the projector must be correctly focused with the zoom and iris set in their viewing positions This will assure that the front of the lens is positioned correctly Hold the motorized sled up to the projector and determine if the LENS IN position will be on the motor housing logo side or the pulley housing smaller box side This will determine the score mark you will use see below Measure 2 1 8 inches from the front of the projector lens and lightly draw a line parallel to the front of the lens Mark the center line of the projector lens along this parallel line Line up the back of the mounting bar to the parallel line just marked Align the center of the projector lens mark with the correct score line on the mounting bar and mark the six drill hole locations using the mounting bar itself as a template Drill out the holes for the fasteners Front of Projector Lens Zoomed and Focused Lens Center Line Pulley Housing Side 2 125 Score Mark Mark for Drill Motor Housing Side Mark for Drill Mark for Drill Score Mark F
15. ng speed modes FAST and SLOW Slow is the default from the factory The slow mode reduces the inertia exerted by the lens on the mounting system by accelerating and decelerating very slowly and by limiting the top speed of the lens as it traverses the sled If the sled is on a very rigid mount that is not D subject to any sway you can speed up the traversal speed by setting the lens speed to FAST If you notice any swaying in the mounting reset E o the speed to SLOW eee Some users set the speed to SLOW when used in conjunction with screen masking systems Your By a speed setting will be remembered by the control Q 2 unit even if the power is interrupted Congratulations you are now ready to experience ow widescreen cinema from your home theater For more information please visit our website at http www OptomaUSA com User s Manual 9 User s Manual BX AL133 Remote Control and Motor Operation The LED indicator on the sled will glow when the unit is ON and flash when any button is pressed It will also flash when the lens is in motion The LED will be off in standby mode Buttons OFF Puts the sled in standby mode ON Turns the sled from standby to ON LENS OUT Commands the lens to move into the LENS OUT position Holding the button for several seconds re programs the current position as the new LENS IN position The lens sled will acknowledge the request by flashing
16. or more information please visit our website at http www OptomaUSA com User s Manual 6 User s Manual gt G7 AN ig Be BC 2 Securing the mounting plate Because the mechanism and lens are heavy make sure the mounting fasteners and surface are extremely secure Remember that the sled motor will be starting and stopping a heavy weight thousands of times through normal use Ceiling mounted lenses require a secure surface board or lens enabled projector mount that is securely affixed to the studs or ceiling 9 Sheetrock anchors alone are insufficient Secure the mounting bar to a plate painted joists Use of a commercial mounting system enabled for anamorphic lenses is highly recommended Use all six screw holes and tighten fasteners securely Vibration from the motor and reciprocal lens movement will loosen any fasteners that are not absolutely tight and secure Do not attach the lens or power up the sled yet Adjustment and alignment are much easier at this point without the lens 3 Attaching the lens bracket to the adaptor plate Remove the bracket mounting screws from the inside holes in the adaptor plate and use them to attach the lens bracket supplied with the Optoma BX AL133 anamorphic lens system If the lens is attached to the bracket make sure to remove the lens prior to attaching to the lens adaptor plate Holes for Ceiling or Plate Mount x6 Fasteners Lens Bracket Screws x4 For more inform
17. ted configuration you will want to turn the logo around so that it is right side up with the mounting bar below the projector pwd gt Remove Screws To reverse the logo remove the 4 y screws securing the motor housing cover Lightly slide the sheet metal cover and lift it off Once removed Lomo fh you can easily access the logo raglan gt plate Remove the two small screws securing the logo plate turn the plate around and re install O O the screws Install the motor cover housing back on the sled with the original screws Rotate Logo Upright The logo backlight may be turned off using the remote control An alternative to reversing the logo plate is to simply turn off the back light to make the logo less conspicuous Replace Screws For more information please visit our website at http www OptomaUSA com User s Manual 5 User s Manual gt G7 AN ig Be BC Mounting Sled to Shelf or Ceiling When installing the motorized sled make sure that you first mark screw locations using only the sled without the lens and or the lens bracket in place and will work them loose and cause the mechanism to fall Mount the sled on a plate q Do not rely on fasteners embedded in sheetrock alone Reciprocal lens movement can board or lens enabled projector mount affixed to ceiling joists for safety Once the sled is secure attach the brack
18. ty Opening the case will void the warranty 10 Exercise extreme caution when working on a ladder Do not work directly above another person particularly a child Plan all work carefully Accidentally dropping a drill hammer or the lens assembly can cause serious bodily injury 11 Pushing or forcing the sled by hand may damage the circuit board Should it be necessary to move the sled by hand make sure it is done slowly and lightly 12 The Optoma motorized sled will ramp up and down at the beginning and end of the traversal to minimize swaying forces at the mount As the motor accelerates and brakes there is a minimal change in the sound FE CE This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation September 2005 Edition For more information please visit our website at http www OptomaUSA com User s Manual 2 User s Manual BX AL133 Introduction Thank you for purchasing the Optoma BX AL133 anamorphic lens The lens and motorized sled is outfitted with a custom mechanism designed exclusively for use ina home theater environment No oil or liquid based lubricants are used to assure the maximum cleanliness of optical components Both lens and drive will provide years of maintenance free service
19. ty installation A service charge may be applied to any returned product requiring cosmetic attention or to the repair of any damage not covered under this warranty For more information please visit our website at http www OptomaUSA com User s Manual 15 User s Manual gt G7 AN ig Be BC Addendum Adapter Plate This attachment plate is designed to be installed onto a ceiling mounted projector The location or orientation of the ceiling mount does not need to change Contents Lens Plate 1 Lens Plate 1 Bag Projector Attachment Parts 1 Assembly Kit Includes 2 Plate Hook Assemblies 1 Chain 6 ft 4 Chain Ends 4 Lens Mounting Assemblies 4 Sled Mounting Screws 2 Sled Safety Assemblies 1 Hex Key Ceiling Side Top Holes For E Projector and Ceiling Mount E Hooks E Lens Only E Motorized Sled Required Tools and Equipment 2 Ceiling Hooks 40 lbs Capacity Each 1 Phillips Screwdriver 1 Pair of Pliers 1 Strong Pair of Scissors or Wire Cutters 1 INSTALL PLATE HOOK ASSEMBLIES Use the pliers to bend the closed end of the hooks apart just enough to insert the end of the chain Install the plate hook assemblies in the two holes Place one hook end on the top side and then continue the assembly down in the order of nut washer lens plate washer lock washer and nut Arrange the assembly so that the plate is in the center of the threaded hook shaft 2 ATTACH LENS PLATE Remove the projector
Download Pdf Manuals
Related Search