Optiview TRKPTZ-18NX User's Manual
Contents
1. 1 3 1 6 1 12 1 25 1 50 1 75 1 100 1 120 1 150 1 215 1 300 1 425 1 600 1 1000 1 1250 1 1750 1 2500 1 3500 1 6500 1 10000 IRIS LEVEL Iris level is the lens function that automatically opens and closes the iris in response to changing light conditions The default setting is F2 0 Settings include F2 0 F1 6 F1 4 Close F22 F19 F16 F14 F11 F 9 6 F8 0 F6 8 F5 6 F4 8 F4 0 F3 4 F2 8 F2 4 AGC LEVEL AGC Automatic Gain Control automatically adjusts the amount of video amplification to maintain a Full 1 volt peak to peak video signal output The default setting is 0 dB Settings include OdB 2 dB 4 dB 6dB 8 dB 10 dB 12 dB 14 dB 16 dB 18 dB 20 dB 22 dB 24 dB 26 dB 28 dB BRIGHT LEVEL The default setting is 0 dB F2 0 Settings include 0 dB F2 0 0 dB F1 6 0 dB F1 4 2 dB F1 4 4 dB F1 4 6 dB F1 4 8 dB F1 4 10 dB F1 4 12 dB F1 4 14 dB F1 4 16 dB F1 4 18 dB F1 4 20 dB F1 4 22 dB F1 4 24 dB F1 4 26 dB F1 4 28 dB F1 4 Close 0 dB F22 0 dB F19 0 dB F16 0 dB F14 0 dB F11 0 dB F9 0 0 dB F 8 0 0 dB F6 8 0 dB F5 6 0 dB F4 8 0 dB F4 0 0 dB F3 4 0 dB F2 8 0 dB F2 4 NOTE LOW LIGHT LIMIT IRIS LEVEL AGC LEVEL BRIGHT LEVEL can set only when AE MODE and LOW LIGHT MODE are set as Manual II Figure 3 7B PROGRAM AE MODE settings are for MODEL TRKPTZ18XX and TRKPTZ26XX AE MODE Settings include AUTO AU IR1 AU IR2 AU DSS 22 Auto2. 2 From the menu of Fig 3 25 press Close to return to the menu of Fig 3 24 3 From the menu of Fig 3 25 press Open to enter menu of Fig 3 26 to edit the windows location EDIT WINDOW LOCATION Figure 3 26 EDIT WINDOW LOCATION 4 From the EDIT WINDOW LOCATION menu shown in Fig 3 26 Move joystick left zoom in left right from the zone center Move stick right zoom in left right from the zone center Move stick up zoom in up down from the zone center Move stick down zoom in up down from the zone center 5 After the zone is set press Open to save the settings and return to menu of Figure3 24 3 6 8 Edit Windows Zoom From the menu of Figure 3 24 move stick and move cursor to Edit Window Zoom press Open to enter below menu EDIT WINDOWS IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL Figure 3 27 EDIT WINDOWS Pan the joystick to adjust the zoom times 46 Auto Zooming Tracking Dome Camera User Manual Press Close to discard the setting and return to Fig 3 24 Press Open to save the setting and return to Fig 3 24 3 6 9 Heater Setting From the dome setting 2 menu shown in Fig3 17 move joystick and move cursor to HEATER SETTING press Open to enter the following menu Figure 3 28 Y HEATER SETTING HEATER DISPLAY ON HEATER MODE AUTO TEMPERATUEE SET 33 C BACK EXIT E i Figure 3 28 HEATER SETTING HEATER DISPLAY Heater display shows heater state ON Screen will display
3. LABEL 2 Press iris Open It will show as follows ZONE NUMBER 1 ZONE LABLE assas 0123456789YZ yz ABCDEFGHIJKLMNOPQRSTUVWX abcdefghljklmnopqrstuvwx INPUT MODE CHARACTER OK CN SP BP Figure 3 15 ZONE SETTING 34 Auto Zooming Tracking Dome Camera User Manual 3 Move joystick to position the cursor beside a character Press iris Open to confirm selection To clear a character position the cursor beside BP and then press iris Open 4 When a label is inputted move the cursor to Ok then press iris Open to save and return to the Preset menu 5 When a label is inputted move the cursor to CN then press iris Open to cancel and return to the Preset menu To clear a zone 1 Move joystick to position the cursor beside CLEAR ZONE 2 Press iris Open Follow the instructions on the screen Note The ZONE NUMBER 9 is the dome s label 3 5 8 Clears Setting Move joystick to select lt CLEARS gt then press Open to enter the clears menu shown as Fig 3 16 a CLEARS CLEAR ZONES CLEAR PARESETS CLEAR PATTERNS RESTORE FACTORY DEFAULTS BACK EXIT a A Figure 3 16 CLEARS SET CLEAR ZONES Clear all zones To clear a specific zone please refer to 35 Auto Zooming Tracking Dome Camera User Manual ZONES section CLEAR PRESETS Clear all presets To clear a specific preset please refer to the PRESETS section CLEAR PATTERNS Clear all patterns To clear a specific pattern please r
4. 10 Gen 25 10 5 92 20 52 35 20 5392 30 5b 45 30 15 92 40 52 55 40 25 92 50 5 65 50 35 92 60 5 75 60 45 92 70 5 85 70 55 92 80 5 95 80 70 92 3 6 6 Set Windows Move joystick to select lt SET WINDOWS gt then press Open to enter the set windows menu shown as Fig 3 24 SET WINDOWS WINDOWS NUMBER lt EDIT WINDOWS LOCATION gt lt EDIT WINDOW ZOOM gt ENABLE WINDOWS CLEAR WINDOWS BACK EXIT OFF CN Figure 3 24 SET WINDOWS MENU Windows Number 1 8 Edit windows location Edit the location of windows 44 Auto Zooming Tracking Dome Camera User Manual blanking lt Edit window zoom gt set the zoom of the blanking The blanking will take effect when the video is zoomed to this time or above Enable Windows Enable or disable the current blanking Clear windows clear the current windows blanking Operation 1 Move joystick to select a item 2 Press iris Open 3 Move joystick to select parameters 4 Press Open 3 6 7 Edit Windows Location Move joystick and move cursor to lt EDIT WINDOWS LOCATION gt then press open to enter the menu as Fig 3 25 EDIT WINDOWS LOCATION IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL Mas z Figure 3 25 EDIT WINDOWS MENU Operation 1 From Fig 3 25 move cursor to make sure it is at the center points of blanking and coordinate 45 Auto Zooming Tracking Dome Camera User Manual
5. Auto Zooming Tracking Dome Camera User Manual is a large amount of zoom 4 Auto Flip When the dome camera tilts downward and goes just beyond the vertical the dome camera rotates 180 degrees automatically Afterwards the dome camera starts moving upward even you still hold joystick in the down position Once you let go of the joystick after the dome rotates joystick control returns to normal operation The auto flip feature is useful for following a person who passes directly beneath the dome 5 Setup and call Preset Preset function is that dome saves current horizontal angle and title angle of pan tilt zoom and position parameters into the memory When necessary dome calls up these parameters and adjusts Pan Tilt Zoom accordingly so that the camera goes to that position again Operator can save and call up presets easily and promptly by using keyboard controller or infrared controller This dome supports up to 256 presets 6 Lens Control a Zoom control User can adjust camera s zoom wide or near by using controller and get desired image b Focus control System defaults Auto Focus mode in which the lens and camera will automatically adjust the focus to give the best image Focus can also be controlled manually from the controller if required Press FOCUS NEAR or FOCUS FAR key to manually focus Auto Zooming Tracking Dome Camera User Manual Focus can be manually controlled via keyboard or matrix
6. Focus press FAR or NEAR key 7 Iris Press OPEN or CLOSE key Section 3 Menu Configuration You need to install the dome system before using this 13 Auto Zooming Tracking Dome Camera User Manual manual Please refer to the installation packet supplied with the back box for installation instructions After installed properly power up the camera It will start a configuration sequence After the configuration is done the monitor will display as below PTOL PELCO D COMM 2400 N 8 1 ADDR 0 This information will remain on the monitor until dome operation begins Please refer to the following pages for more about how to operate and program the camera Access main menu preset 95 Please refer to the Accessing Main Menu Preset 95 section 1 Move joystick to position the cursor beside menu selection 2 Move the joystick up or down to submenu cursor selections 3 Press iris Open to confirm selection 4 Press iris Close to cancel selection 5 Below instructions are based on using control keyboard as control device 14 Auto Zooming Tracking Dome Camera User Manual 3 1 Main Menu Set 95 preset to access main menu s MAIN MENU lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS 1 gt lt DOME SETTINGS 2 gt lt DOME LABLE gt RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXIT x Figure 3 1 MA
7. number E g preset 1 will go to Alarm 1 PATTERN 1 Dome runs pattern 1 when alarm is triggered PATTERN 2 Dome runs pattern 2 when alarm is triggered PATTERN 3 Dome runs pattern 3 when alarm is triggered PATTERN 4 Dome runs pattern 4 when alarm is triggered AUTO SCAN Dome starts auto scan operation when alarm is triggered RANDOM SCAN Dome starts RANDOM scan operation when alarm is triggered FRAME SCAN Dome starts FRAME scan operation when alarm is triggered TRACKING Dome calls preset and start auto tracking Tracking function only available with the models named TRKPTZ18XXPT TRKPTZ22XXPT TRKPTZ23XXPNT and TRKPTZ26XXPNT 4 Press iris Open to confirm selection 39 Auto Zooming Tracking Dome Camera User Manual Set auxiliary to activate 1 Move joystick to position the cursor beside ACTIVATE AUX 2 Press iris Open 3 Move the joystick up or down to view the following available selections OFF default Not activated 1 An alarm action will close AUX 1 2 AN alarm action will close AUX 2 4 Press iris Open to confirm selection Set alarm contact 1 Move joystick to position the cursor beside ALARM CONTACT 2 Press iris Open 3 Move the joystick up or down to view the following available selections OFF default close ON open 4 Press iris Open to confirm selection 3 6 3 Aux Setting Move joystick to select lt AUX gt then press Open to enter the aux menu shown as
8. please refer to control keyboard or matrix operation manual for detailed operation When on manual focus status operations such as adjusting positions or preset setting will resume the camera to auto focus status The camera will not auto focus in the following status Target is not in the center of image Targets are in near and far at the same time Target is of strong light object Such as spotlight etc Target is behind the glass with water drop or dust Target moves too fast Target is too big such as wall Target is too dark or vague c Iris control System defaults AUTO IRIS Camera can adjust immediately according to the alteration of back ground illumination to get a steady image Users may adjust Iris manually by using a controller to get required image quality Users can call back AUTO IRIS by moving the joystick 7 Auto Back light Compensation Lens has been divided to six areas for back light compensation In a strong light background camera will auto compensate the darker object and adjust light input from the lighter area to avoid a mass image that usually presents a sharp contrast of brightness and darkness 8 Auto White Balance Auto Zooming Tracking Dome Camera User Manual Camera can automatically adjust white balance according to the alteration of background lightness to give a true color image 9 Backlight Compensation BLC If a bright backlight presents the subjects in the picture may a
9. Fig 3 20 40 Auto Zooming Tracking Dome Camera User Manual AUX DWELL TIME lt SECS gt 1 0 DWELL TIME lt SECS gt 2 0 BACK EXIT Figure 3 20 AUX An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate An auxiliary out put is programmable to trigger from an alarm or from a controller An AUX 1 command from the controller will place a ground at the output of AUX 2 to operate the device that is connected to it Setting include 0 30secs An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the device that is connected to it Setting include 0 30secs 3 6 4 Password Setting Move joystick to select lt PASSWORDs then press Open to enter the password menu shown as Fig 3 21 41 Auto Zooming Tracking Dome Camera User Manual PASSWORED EBABLE PASSWORD OFF lt EDIT PASSWORD gt BACK EXIT Figure 3 21 PASSWORED This setting protects it from unauthorized changes to the dome settings ENABLE PASSWORD Open or close the password features EDIT PASSWORD Four Numbers p E PLEASE INPUT OLD PASSWORED PASSWORD 1234567890 CLEAR ENTER EXIT i Figure 3 22 EDIT PASSWORD 1 Move joystick to position the cursor beside a number Press iris Open to confirm selection 2 When password is inputted move the cursor to ENTER and press iris Open comes to the PLEASE INPUT NEW PASSWORED 3 I
10. Follow the directions displayed on the monitor CLEAR SCAN STOPS To clear scan stops 1 Move joystick to position the cursor beside clear scan stops 2 Press iris Open 3 Follow the directions displayed on the monitor SET MANUAL LIMIT lt Set manual limit gt is to set the P T Z s moving range To set manual limit 1 Move joystick to position the cursor beside set manual limit 2 Press iris Open 28 Auto Zooming Tracking Dome Camera User Manual 3 Follow the directions displayed on the monitor SET AZIMUTH ZERO Azimuth is the pan angle from 0 to 359 Azimuth zero is the pan position you specify to be the 0 point Azimuth zero is normally set to magnetic north Once set azimuth and compass readings are based on the set Azimuth Zero point To program azimuth zero 1 Move joystick to position the cursor beside set azimuth zero 2 Press iris Open 3 Follow the directions displayed on the monitor CLEAR AZIMUTH ZERO 1 Move joystick to position the cursor beside CLEAR AZIMUTH ZERO 2 Press iris Open 3 Follow the directions displayed on the monitor 3 5 4 Power Up Move joystick to select lt power up gt press Open to enter the power up menu shown as Fig3 10 POWER UP POWER UPACTION NONE BACK EXIT Figure 3 10 POWER UP POWER UP ACTION 29 Auto Zooming Tracking Dome Camera User Manual This setting defines a specific activity scan preset pattern to be p
11. IN MENU Access other OSD menus 1 Move the joystick up or down to position the cursor beside others OSD menus 2 Press iris Open to confirm selection 3 2 Select Language The language for the on screen menus is selectable Available languages include English and Chinese The factory default language is English Changing the display language 1 In main menu move the joystick to position the cursor beside LANGUAGE 2 Press iris Open The cursor moves to the right beside the currently selected language 15 Auto Zooming Tracking Dome Camera User Manual 3 Move the joystick up or down to view selections Press iris Open to confirm selection All on screen menus are changed into the selected language 3 3 System Information Move joystick to select lt system information gt press Open to confirm the system information menu shown as Fig 3 2 N SYSTEM INFORMATION COMM 9600 N 8 1 ADDRESS 255 PROTOCOL PELCO P PRESETS NUMBER 256 LANGUAGE ENGLISH TEMPERATURE 36 C BACK EXIT i Figure 3 2 SYSTEM INFORMATION The system information screen shows dome language protocol and other configuration information System information settings shown are not changeable in this interface It is for reference only Follow the following steps to display the system information screen 1 Move the joystick to position the cursor beside SYSTEM INFORMATION 16 Auto Zooming Tracking Dome Camera User M
12. ODpUVIevvs Auto Zooming Tracking Dome Cameras User Manual Auto Zooming Tracking Dome Camera User Manual Contents Section MSIUICHOM 25 otto ORE ID ED EED OD ED ED tan 3 1 1 Production Introducing 3 122 Character usato e E dte e a eate 3 1 3 Function Description ee ee Re Re Re ee 4 1 4 Specification Comparison Chart 9 Section 2 Normal Operation eere ee erected 12 Section 3 Menu Configuration eese 13 3 1 Main Menu see ee ee Re Re emen 15 3 2 Select Language ER e e et tt 15 3 9 oysiem Informatio xo oe eo ee oe ee ee Bee e 16 3 4 Display Setup wes eee eie ooo aie 17 3 4 1 Display SEP stede ese ta Eg See ee 17 3 4 2 Label Position sse 18 3 5 Dome Settings T c accen eee eerte e ceret 19 3 5 1 Dome Settings T cgit ER io adds 19 3 5 2 Camera Settings ies Ee RE GEREEN 19 3 5 3 Motion SOUITIQ GED d o P ARP dens 26 3 5 4 Power Up et Be ee De EV EE 29 3 5 5 Presets Setting 5 eet t des 30 3 5 6 Patterns Selling i ous cni RE rt end ese 32 3 5 7 Zone Setting occisa RR so tetas eeu 33 3 5 8 Clears Seting ee e eee 35 3 5 9 Presets Number ees ese ee ee ee Re 36 3 6 Dome Settings 2 Menu ee sene 36 3 021 NE ES EE RE Ee i ete 37 3 6 2 Alarms Sell iti oce ee Ge Gee ee ek 38 3 6 3 Aux Selling o e D e e eh 40 Auto Zooming Tracking Dome Camera User Manual 3 6 4 Password Selihd EE Ee EE ceda 41 3 6 5 Windo
13. Zooming Tracking Dome Camera User Manual AU DSS IR1 AU DSS IR2 AU DSS IR3 SHUTTER PR IRIS PRIO and AGC PRIORI IR CUT FILTER Settings include IN and OUT LOW LIGHT LIMIT Settings include 1 1 5 1 3 1 6 1 12 1 25 1 50 SHUTTER Settings include 1 30000 1 10000 1 4000 1 2000 1 1000 1 500 1 250 1 150 1 100 1 50 1 25 1 12 1 6 1 3 1 1 5 IRIS LEVEL Iris level is the lens function that automatically opens and closes the iris in response to changing light conditions The default setting is F1 6 Settings include F1 6 F2 2 F3 2 F4 4 F6 4 F8 8 F12 F17 F24 F34 AGC LEVEL AGC Automatic Gain Control automatically adjusts the amount of video amplification to maintain a Full 1 volt peak to peak video signal output The default setting is 0 dB Settings include OdB 6dB 12dB 18dB 24dB and 30dB 3 5 2 2 Other Menu Move joystick to select lt others gt press Open to enter the others menu shown as Fig3 8 23 Auto Zooming Tracking Dome Camera User Manual d OTHERS B IR CUT FILTER AUTO IR CUT FILTER COLOUR AUTO IRIS ON SHARPNESS ON SHARPNESS LEVEL 5 AUTO WHITE BALANCE ON OFF R GAIN 214 B GAIN 164 BACK EXIT M A Figure 3 8A OTHER MENU d OTHERS AUTO IRIS ON AUTO IRIS LEVEL 91 AUTO IRIS PEAK 16 SHARPNESS ON SHARPNESS LEVEL 39 AUTO WHITE BALANCE ON R GAIN 652 B GAIN 427 BACK EXIT d J Figure 3 8B OTHER MENU Note Figure 3 8A shows Other Menu on
14. al distributor Below instructions are based on using control keyboard as controlling device 1 Dome Self testing after Powered up After powered up the dome will conduct reset procedure In this procedure the dome firstly pans to the default horizontal origin point and finally tilts to the vertical 45 position to complete the self testing After the dome stops it means the camera has completed the self testing and is ready to receive control commands 2 Pan and tilt Move joystick up down right left 3 Set up preset Move to next position Then press PRESET NUM preset NO ENTER and the dome will save current horizontal angle and title angle of pan tilt zoom and position parameters into memory 4 Call preset Press PRESET NUM Preset NO ENTER and the 12 Auto Zooming Tracking Dome Camera User Manual dome will calls these parameters saved in memoriy and adjust Pan Tilt Zoom of the camera to that position go Auto tracking 37 82 Auto switch sequentially among preset positions Clear all presets positions Lo eme WENE TEN Extended Presets Note For others dynamics controllers with only 64 or 40 presets On the menu of PRESETS NUMBER set it as 64 or 40 Then you can use presets listed in Presets 2 in stead 5 Zoom You can press IN or OUT key continuously or revolve the joystick to get desired zooming times 6
15. amera s control cycle camera power Cycling camera power resets the camera but does not change any saved camera settings REBOOT SYSTEM Reboot the system if it does not operate or if there is no control Rebooting the system will cycle dome and camera power without changing programmed dome settings Q 52
16. anual 2 Press iris Open 3 4 Display Setup 3 4 1 Display Setup Move joystick to select DISPLAY SETUP gt press Open to enter the display setup menu shown as Fig3 3 J DISPLAY SETUP PRESET LABEL ON ZONE LABEL ON ZOOM ON AZIMUTH ELEVATION ON CAMERA LABEL ON LABEL POSITION BACK EXIT k J Figure 3 3 DISPLAY SETUP Display setup enables you to program how labels are displayed on the monitor The following labels are available PRESET LABEL Identifying preset ZONE LABEL Identifying zone ZOOM Identifying zooming times AZIMUTH ELEVATION Amount of pan from 0 and the amount of tilt from 0 horizontal CAMERA LABEL Identifying dome A preset label is displayed when a preset is called A zone label is displayed when the system moves into a zone The zoom 17 Auto Zooming Tracking Dome Camera User Manual ratio label is displayed when zoom is activated Azimuth elevation and direction labels are displayed when pan tilt is activated The dome label is displayed when the dome label is activated The following settings are available foe each label OFF The label is not displayed when activated ON The label shows when activated 3 4 2 Label Position Labels can be placed anywhere on the monitor This feature enables you to customize the place of labels on monitor screen se ZONE CAMERA PRESET SAVE RESET AZIMUTH ZOOM a Figure 3 4 Label Position To set a label
17. cter Press iris Open to confirm selection To clear a character position the cursor beside BPE and then press iris Open d After the label is inputted move the cursor to Ok then press iris Open to save and return to the Preset menu e After the label is inputted move the cursor to CE then press iris Open to cancel and return to the Preset menu 31 Auto Zooming Tracking Dome Camera User Manual 3 Edit preset scene a Move joystick to position the cursor beside EDIT PRESET SCENE b Press iris Open c Follow the direction displayed on the monitor 4 Clear a preset a Move joystick to position the cursor beside CLEAR PRESET b Press iris Open c Follow the direction displayed on the monitor 3 5 6 Patterns Setting Use stick to select patterns Open to enter the patterns menu shown as Fig3 13 ae PATTERNS PATTERN NUMBER 1 lt PROZGRSM PATTERN gt CLEARE PATTERN gt BACK EDIT Figure 3 13 PATTERNS PROGRAME PATTERN A pattern is function that the camera can save its moving course and will repeat that course when demanded To program a pattern 1 Move joystick to position the cursor beside PATTERN NUMBER and then press iris Open 32 Auto Zooming Tracking Dome Camera User Manual 2 Move the joystick up or down to view selections Press iris Open to confirm selection 3 Move joystick to position the cursor beside PROGRAM PATTERN 4 Press iris Open 5 Foll
18. ctive after it has physically cleared 3 6 2 Alarms Setting Move joystick to select lt ALARM NUMBER then press Open to enter the alarm number menu shown as Fig 3 19 a ALARM NUMBER 1 ALARM PRIORITY LOW ALARM ACTION NONE ACTIVATE AUX OPEN ALARM CONTACT OPEN BACK EXIT S Figure 3 19 ALARM SETTINGS Follow below steps to program alarm settings Select alarm number 1 a Move joystick to position the cursor the cursor beside ALARM NUMBER b Press iris Open c Move the joystick up or down to view selections Press iris Open to confirm selection 2 Move the joystick to position the cursor beside Alarm Settings Press iris Open Select alarm priority 1 Move joystick to position the cursor beside Alarm Priority 38 Auto Zooming Tracking Dome Camera User Manual 2 Press iris Open 3 Move the joystick up or down to view the available selections Available settings include HIGH MEDIUM and LOW default If multiple alarms with different priorities are active at the same time the dome will only go to the alarms with the highest priority 4 Press iris Open to confirm selection Set alarm action 1 Move joystick to position the cursor beside Alarm action 2 Press iris Open 3 Move the joystick up or down to view the available selections Below are the settings for alarm action NONE No action when alarm is triggered PRESET Dome goes to the preset that is the same as the alarm
19. e system is capable of eight zones each with a 6 character label 17 Alarms Alarms input The dome has four alarm inputs which can be programmed as high medium or low priority When an alarm is received an input signal to the dome triggers the user defined action go to preset run pattern etc programmed for the alarm Auxiliary output An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate An auxiliary output is programmable to trigger from an alarm or from a controller 18 Password protection The dome features password protection to prevent unauthorized changes to the dome settings You can open the System Information and Display Setup screens but cannot access any of the Dome Settings menus 19 Windows blank Auto Zooming Tracking Dome Camera User Manual A set window can be reversed so that it is the only visible tilt area of the scene All other parts of the tilt area of the scene will be blanked NOTE Be the same with only the model of TRKPTZ 18NX TRKPTZ 26NX TRKPTZ 18NX TRKPTZ 26NX 20 Auto tracking Revolutionary motion tracking technology making it realize intelligent surveillance easily with the help of alarming function 1 4 Specification Comparison Chart Auto Zooming Tracking Dome Camera User Manual Model 1801 TRKPTZ TRKPTZ TRKPTZ TRKPTZ TRKPTZ 1802 1803 22X 23X Signal Format PAL NTSC Image Senso
20. efer to the PATTERNS section RESTORE FACTORY DEFAULTS This is to restore leaving factory s default settings 3 5 9 Presets Number This is to set the dome s preset number 3 6 Dome Settings 2 Menu Move joystick to select lt DOME SETTINGS 23 then press Open to enter the dome settings 2 menu shown as Fig 3 17 DOME SETTINGS 2 B ALARMS lt AUX gt lt PASSWORD gt lt WINDOWS BLANKING gt lt HEATER SETTING gt CRUISE SETTING TRACKING SETTING BACK EXIT Ss P 36 Auto Zooming Tracking Dome Camera User Manual Figure 3 17 DOME SETTINGS 3 6 1 Alarms Move joystick to select ALARMS then press Open to enter the alarms menu shown as Fig 3 18 a N ALARMS ALARM NUMBER 1 SEQUENCE SECS 1 lt ALARM SETTINGS gt lt CLEAR SET gt BACK EXIT Figure 3 18 ALARMS The dome has seven alarm inputs which can be programmed as high medium or low priority When an alarm is received the inputted signal to the dome triggers the user defined action go to preset run pattern etc programmed for the alarm There are three alarm settings ALARM NUMBER Use this to select alarms number SEQUENCE lt SECS gt This is the time the dome will perform an alarm activity when more than one alarm of the same priority occurs at the same time RESET DELAY SECS 37 Auto Zooming Tracking Dome Camera User Manual This is the length of time the dome considers the alarm to be a
21. erations 1 From the menu in Fig3 21 select relative item of 1234567890 with the joystick 2 Press Open and select a specific parameter Select options with joystick 3 6 11 Tracking Setting Move joystick to select TRACKING SETTING press Open to enter the tracking menu shown as Fig 3 30 a TRACKING SETTING DEFAULT SETTING SIZE SNS MIDIUM GRAY SNS MIDIUM LOST ACT TO HOME amp TRACKING AUTO ZOOMING ON WAIT TINE lt S gt 40 lt TRACKING BOUNDARY gt BACK EXIT d J Figure 3 30 TRACKING SETTING Default Setting tracking setting to default 49 Auto Zooming Tracking Dome Camera User Manual Size SNS the size of the target in the screen Medium Large Small are selectable GRAY SNS the sensitivity of the moving object Medium High and Low are selectable LOST AC the action when the moving object is lost Parameters include return home and tracking keep tracking stop tracking AUTO ZOOMING The dome will auto zoom in out according to the size and distance of the object Parameters can be ON OFF WAIT TIME lt S gt When the tracking object is lost the interval of time for the dome to wait before Lost Action Parameters can be 5 10 15 20 25 30 35 40 seconds lt TRACKING BOUNDARY to set the valid area of tracking function UP DOWN LEFT RIGHT Operations 1 In the menu of Fig 3 30 move joystick to a specific item 2 Press Open 3 Move joystick to select desired pa
22. erformed after the dome is powered up Following settings are available NONE default No action AUTO SCAN Dome starts auto scan operation RANDOM SCAN Dome starts random scan operation FRAME SCAN Dome starts frame scan operation PRESET 1 Dome goes to preset 1 PRESET 8 Dome goes to preset 8 PATTERN 1 Dome runs pattern 1 PATTERN 2 Dome runs pattern 2 PATTERN 3 Dome runs pattern 3 PATTERN 4 Dome runs pattern 4 3 5 5 Presets Setting Move joystick to select lt PRESETS gt press Open to enter the presets menu shown as Fig3 11 a PRESETS PRESET NUMBER 1 PRESET NOT DEFINEO EDIT PRESET LABEL gt lt EDIT PRESET SCAENE gt lt CLEAR PRESET gt BACK EXIT LM m Figure 3 11 PRESET The dome camera has 64 programmable preset positions Follow below steps to program a preset 30 Auto Zooming Tracking Dome Camera User Manual 1 Select preset number a Move joystick to position the cursor beside PRESET NUMMBER press iris Open b Move the joystick up or down to view selections Press iris Open to confirm selection 2 Edit preset label a Move joystick to position the cursor beside EDIT Preset label b Press iris Open It will show PRESET NUMBER PRESET LABLE fesse 0123456789YZ yz ABCDEFGHIJKLMNOPQRSTUVWX abcdefghljklmnopqrstuvwx INPUT MODE CHARACTER OK CN SP BP Figure 3 12 CHARACTER INPUT c Move joystick to position the cursor beside a chara
23. heater state OFF Screen will not display heater state HEATER MODE Heater mode is to set the heater s startup mode AUTO Heater starts when temperature is lower than lower temperature OFF Heater is closed ON Heater is open TEMPERATURE SET 47 Auto Zooming Tracking Dome Camera User Manual Temperature set is to set the heater s startup temperature Operations 1 2 3 4 Move joystick to select an item Press Open Move the stick to select a parameter Press Open 3 6 10 Cruise Setting From the menu shown in Fig3 17 move joystick to select CRUISE SETTING press Open to enter the following menu E CRUISE DWELL TIME lt SECS gt 7 PRESET LIST 1 1 ON 0 OFF 1234567890 0110010111 BACK EXIT Fig 3 29 CRUISE Dwell Time the lasting time of preset from 5 250 seconds Preset List parameter 1 2 3 Operations 1 2 3 4 In the menu move the joystick to select a specific item Press Open Select the parameter with the joystick Press Open 48 Auto Zooming Tracking Dome Camera User Manual 1 ON 0 OFF Note they are not changeable 1234567890 display info not changeable When the preset list is 1 1 2 3 4 5 6 7 8 9 0 indicates presets from 1 10 When it is 2 it indicates presets from 11 20 When it is 3 it indicates presets from 21 30 000001010 1 select the cruising presets 1 for cruising 0 for not cruising Op
24. ional pan modes ON default Enables the proportional pan mode OFF Disables proportional pan mode The pan speed will not depend on the zooming times PARK TIME This feature enables the dome to operate a specified activity scan preset or pattern after a programmed time of idleness Park time can be programmed from 1 minute to 720 minutes 12 hours or set to zero which disables this feature The default setting is zero PARK ACTION This feature will define the activity when the dome parks The following settings are available NONE default No action AUTO SCAN Dome starts auto scan operation RANDOM SCAN Dome starts frame scan operation FRAME SCAN Dome starts frame scan operation PRESET 1 Dome goes to preset 1 PRESET 8 Dome goes to preset 8 PANTTERN 1 Dome runs pattern1 PANTTERN 2 Dome runs pattern2 27 Auto Zooming Tracking Dome Camera User Manual PANTTERN 3 Dome runs pattern3 PANTTERN4 Dome runs pattern4 SCAN SPEED Scan speed is that the dome will pan when in a FRAME SCAN mode Scan speed is adjustable from 1 to 32 via the programming menu SET SCAN STOPS Set Scan Stops are programmable stops that limit the pan range of the dome There must be two limits a left and a right to define an area The dome reverses direction frame scanning when a limit stop is reached To set scan stops 1 Move joystick to position the cursor beside set scan stops 2 Press iris Open 3
25. ly for models named TRKPTZ18XX and TRKPTZ26XX Figure 3 8B shows Other Menu only for the models named TRKPTZ22XX and TRKPTZ23XX AUTO IRIS Auto iris is the lens function that automatically opens and 24 Auto Zooming Tracking Dome Camera User Manual closes the iris in response to changing light conditions Program the auto iris to operate automatically or at a user defined level OFF Auto iris is disabled and for manually control only AUTO The iris is adjusted automatically to produce a constant video output as determined by the Auto Iris level setting NOTE If auto iris is in auto mode it will remain that status until the iris is manually opened or closed The dome will return to auto mode when it pans or tilts more than 15 degrees AUTO SHARPNESS Auto sharpness enhances picture details by increasing the aperture gain of the camera and sharpening the edges in the picture There are two settings ON default The camera automatically keeps at a normal sharpness mode OFF The sharpness of the picture is set manually by programming the sharpness level AUTO WHITE BALANCE This feature automatically processes the viewed image to retain color balance over a color temperature range The default setting for auto white balance is ON R GAN Adjusts the picture output in the red range As you change the value the color changes on your monitor B GAN Adjusts the picture output in the blue range As you 25 Au
26. nput four new passwords move the cursor to ENTER then press iris Open and comes to PLEASE INPUT NEW PASSWORED Input four new passwords 42 Auto Zooming Tracking Dome Camera User Manual 3 6 5 Windows Blanking Move joystick to select WINDOWS BLANKINGs gt then press Open to enter the windows blanking menu shown as Fig 3 23 WINDOWS BLANKING STYLE GRAY BLANK ALL ABOVE OFF BALANK ALL BELOW OFF lt SET WINDOWS gt BACK EXIT Figure 3 22 WINDOWS BLANKING Window blanking enables you to program up to eight four sided user defined areas that cannot be viewed by the operator of the dome system A blanked area will move with pan and tilt functions and automatically adjust in size according to zoom times Style The dome has two styles for window blanking GRAY and SMEAR If style is set to gray the blanked area is covered with a solid gray window If smear is selected images behind the window will be noticeable but not distinguishable BLANK ALL ABOVE BLANK ALL BELOW The dome camera has two style modes for window blanking GRAY and SMEAR If style is set to gray the blanked area is covered with a solid gray window If smear is selected images behind the window will be noticeable but not distinguishable 43 Auto Zooming Tracking Dome Camera User Manual Blanking Parameters BLANK ALL ABOVE BLANK ALL BELOW OFF No Blanking OFF No Blanking 0 5 10 0 4 02
27. ow the directions displayed on the monitor After a pattern is programmed the remaining storage percentage will be displayed on the screen This is the amount of memory available to program the remaining patterns CLEAR PATTERN 1 Move joystick to position the cursor beside CLEAR PATTERN 2 Press iris Open 3 FOllow the directions displayed on the monitor 3 5 7 Zone Setting Move joystick to select ZONES then press Open to enter the zones menu shown as Fig 3 14 m ZONES ZONE NUMBER 1 ZONE NOT DEFINEO EDIT ZONE LABEL EDIT ZONE gt ZONE ENABLED ON CLEAR ZONE gt BACK EXIT Figure 3 14 ZONES SETTING 33 Auto Zooming Tracking Dome Camera User Manual A zone is pan area defined by a left and right limit on the 360 degree pan plane There are altogether eight zones each can be with a 6 character label TO program a zone 1 Move joystick to position the cursor beside ZONE NUMBER Press iris Open 2 Move the joystick up or down to view selections Press iris Open to confirm selection 3 Move joystick to position the cursor beside EDIT ZONE 4 Press iris Open The Zone programming window will show on the monitor 5 Follow the directions displayed on the monitor After the left stops and right limit stops are set the Zones menu reappears with the ZONE ENABLED option set to be ON To edit a zone label 1 Move joystick to position the cursor beside EDIT ZONE
28. position 1 Move joystick to position the cursor beside a label 2 Press iris Open 3 Move joystick to move the label up down left or right 4 Press iris Open 5 Repeat steps 1 through 4 to position other labels 6 Move the cursor to Save and press iris Open to save settings and return to display setup menu EE 18 Auto Zooming Tracking Dome Camera User Manual 3 5 Dome Settings 1 3 5 1 Dome Settings 1 Move joystick to select lt DOME SETTING 1 gt press Open to enter the dome setting menu shown as Fig3 5 d N DOME SETTINGS1 lt CAMERA gt lt MOTION gt lt POWER UP gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt CLEAR gt PRESET NUMBER 256 BACK a EXIT E Figure 3 5 Dome settings 1 3 5 2 Camera Settings Move joystick to select lt CAMERAs gt press Open to enter the camera menu shown as Fig3 6 19 Auto Zooming Tracking Dome Camera User Manual a E CAMERA ZOME LIMIT X46 BACKLIGHT COMP ON OFF PROGRAM AE MODE OTHERS BACK EXIT EN i Figure 3 6 CAMERA ZOOM LIMIT Zoom limit enables you to define a limitation on zooming times BACKLIGHT COMPENSATION BLC If a bright backlight presents the subjects in the picture may appear dark or as a silhouette Backlight compensation enhances objects in the center of the picture The dome uses the center of the picture to adjust the iris If there is a bright light source o
29. ppear dark or as a silhouette Backlight compensation enhances objects in the center of the picture The dome uses the center of the picture to adjust the iris If there is a bright light source outside this area it will change to white The camera will adjust the iris so that the object in the sensitive area is properly exposed 10 Day and Night Function The IR cut filter of camera module inside the dome can be removed by sending special command so that the camera can change from color to mono The picture is clear even if the illumination is as low as 0 01Lux 11 Auto Cruise The preset positions are programmed for recalled in sequence This feature is called auto cruise Up 30 presets can be set in each cruise tour 12 Patterns A pattern is a saved moving course the camera will repeat its pan tilt Zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function alarm park or power up 13 Auto Scan Make the dome scan 360 range in the current position 14 Random Scan Auto Zooming Tracking Dome Camera User Manual Make the dome random scan 360 range in the current position 15 Frame Scan This feature freezes the scene on the monitor when going to a preset This allows for smooth transition from one preset scene to another 16 Zones Setting A zone is a pan area defined by a left and right limit on the 360 degree pan plane The spectra dom
30. r 14 inch color CCD Horizontal Resolution 480 TVL Video Out 1 0 0 2Vp p P T Speed Pan 0 05 240 sec Tilt 0 03 160 sec S N Ratio 250DB Sensitivity Lux 0 1Lux 0 01Lux 1Lux O 1Lux 0 01Lux IR cut Filter No Yes No Yes AGC Auto Manual BLC Auto Manual F1 4 F3 0 f 4 1 73 8mm F1 6 F3 8 F1 6 F3 7 Lens F1 6 F3 8 f 3 5 91mm f24 88mm i 3 6 82 8mm 10 Auto Zooming Tracking Dome Camera User Manual Optical Zoom 18X 22X 23X Digital Zoom 12X 8X Panning Pan 360 Continuous Tilt 5 92 Range Preset 256 Number Auto Cruise Auto switch from 1 to 30 preset position sequentially Patterns 4 Zone 8 Alarm input 4 Alarm output 2 Windows 8 blanking Interface RS 485 Baud Rate 1200bps 2400bps 4800bps 9600bps 19200bps Address 0 255 Input voltage 24VAC Input power 20W Without Heater 50W With Heater Operating 25 C 70 C Without Heater 50 C 70 C With Temperature Heater Dome Size 6 inch Auto Zooming Tracking Dome Camera User Manual Section 2 Normal Operation These operating instructions cover the basic operation of the dome and its features When the dome is used with other manufacturers control system please refer to the system controller s instructions In the event of special requirements outside the scope of this document it is prefer to contact your loc
31. rameter 4 Press Open 50 Auto Zooming Tracking Dome Camera User Manual 3 6 12 Tracking Boundary From the menu in Fig3 30 move the cursor to lt TRACKING BOUNDRAY gt press Open to enter the following menu Figure 3 31 TRACKING BOUNDARY N BOUNDARY LIMIT OFF CLEAR BOUNDARY LEFT LIMIT OFF RIGHT LIMIT OFF UP LIMIT OFF DOWN LIMIT OFF BACK EXIT ML 2 Figure 3 31 TRACKING BOUNDARY BOUNDAR LIMIT enable disable the boundary CLEAR BOUNDARY clear setting of the current boundary LEFT LIMT set the left tracking boundary RIGHT LIMT set the right tracking boundary UP LIMT set the up tracking boundary DOWN LIMT set the down tracking boundary Operations 1 Move the cursor to a specific function item 2 Press Open 3 Move the joystick to select parameter or operate as per screen instructions 3 Press Open 51 Auto Zooming Tracking Dome Camera User Manual 3 7 Dome Label From the menu shown in Fig3 1 move the cursor to DOME LABEL press Open to enter the following menu Figure 32 DOME LABLE lt EDIT DOME LABEL gt lt CLEAR DOME LABEL gt BACK EXIT Figure 3 32 DOME LABLE EDIT DOME LABEL To edit the dome description and information Please refer to 3 5 4 Edit Preset Label lt CLEAR DOME LABLE Clear current dome label Press Open to enter the menu and then operate with instructions 3 8 Other Functions RESET CAMERA If the camera does not operate or if you close c
32. s changeable Alarm input Alarm output Alarm action Auto Zooming Tracking Dome Camera User Manual The features password protection to prevent unauthorized changes to the dome setting A set window can be reversed so that it is the only visible tilt area of the scene Il other parts of the tilt area of the scene will be blanked Revolutionary motion tracking technology make it realize intelligent surveillance easily with the help of alarming function 1 3 Function Description 1 Setting the dome ID Baud rate and Protocol Every controlling command has a target camera Address Baud rate and Protocol the camera only reacts the controlling command in accordance with its own Address Baud rate and Protocol 2 Object tracking The dome can be manually controlled from the control system by using the joystick on the controller to move the camera up and down right and left to follow objects under observation In default status AUTO IRIS and AUTO FOCUS control of the lens will automatically adjust the picture image on alteration of the background illumination to get a best view 3 Proportional Pan Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of joystick deflection then at wide zoom settings This keeps the image from moving too fast on the monitor when there 4
33. to Zooming Tracking Dome Camera User Manual change the value the color changes on your monitor 3 5 3 Motion Setting Move joystick to select lt MOTION gt press Open to enter the motion menu shown as Fig3 9 di N MOTION AUTO FLIP ON OFF PROPORTIONAL PAN ON OFF PARK TIME MINUTES 0 PARK ACTION NONE SCAN SPEED DEG S 1 lt SET SCAN gt lt MANUAL LIMIT gt lt SET AZIMUTH ZERO gt lt CLEAR AZIMUTH ZERO gt BACK EXIT Nc P FIGURE 3 9 MOTION MENU AUTO FILP When the dome camera tilts downward and goes just beyond the vertical the dome camera rotates 180 degrees automatically Afterwards the dome camera starts moving upward even you still hold joystick in the down position Once you let go of the joystick after the dome rotates joystick control returns to normal operation The auto flip feature is useful for following a person who passes directly beneath the dome There are two auto flip modes ON default Auto flip mode enabled OFF Auto flip mode disabled 26 Auto Zooming Tracking Dome Camera User Manual PROPORTIONAL PAN Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of joystick deflection then at wide zoom settings This keeps the image from moving too fast on the monitor when there is a large amount of zoom There are two proport
34. utside this area it will change to white The camera will adjust the iris so that the object in the sensitive area is properly exposed There are two backlight compensation settings ON Backlight compensation is activated OFF default Backlight compensation is not activated 3 5 2 1 Program AE Mode Move joystick to select lt PROGRAM AE CORTROL gt press Open to enter the PROGRAM AE CORTROL menu shown as Fig3 7 20 Auto Zooming Tracking Dome Camera User Manual PROGRAM AE CORTROL B AE MODE AUTO LOW LIGHT MODE AUTO LOW LIGHT LIMIT 1 50 IRIS LEVEL F2 0 AGC LEVEL OdB BIRGHT LEVEL OdB F2 0 BACK EXIT 7 Figure 3 7A PROGRAM AE CORTROL PROGRAM AE COORTROL PROGRAM AE MODE AUTO IR CUT FILTER INISERT REMOVE BACK EXIT Figure 3 7 B PROGRAM AE CORTROL Note Figure 1 7A shows program AE mode it is only for models names TRKPTZ18XX and TRKPTZ26XX Figure 1 7B shows program AE mode it is only for models named TRKPTZ22XX and TRKPTZ23XXPNT 1 Figure 3 7A PROGRAM AE MODE setting for models named TRKPTZ18XX and TRKPTZ26XX AE MODE Settings include AUTO MANUAL SHUTTER IRIS and BRIGHT LOW LIGHT MODE Settings include AUTO and MANUAL 21 Auto Zooming Tracking Dome Camera User Manual LOW LIGHT LIMIT Low light limit is the maximum duration it is in fractions of a second that electronic shutter will remain open in low light conditions The default setting is 1 50 Settings include 1 2
35. ws Blanking s e 43 3 6 6 Set Windows eee EE RE EE 44 3 6 7 Edit Windows Location sssssess 45 3 6 8 Edit Windows Zoom eene 46 36 9 Heater Selling eere ec or re ree 47 3 6 10 Cruise Setting nme 48 3 6 11 Tracking Setting se EERS eut lan RE doa ua 49 3 6 12 Tracking Boundary ee 51 3 7 Dorme Label vivre hk HR tls 52 3 8 Other Furicli rs 2 iio o pe os 52 Auto Zooming Tracking Dome Camera User Manual Section1 Instruction 1 1 Production Introducing The dome cameras feature high position resolution high speed low price and selectable communication protocols Widely used in surveillance system 1 2 Character e Built in English OSD Menu by which you can change dome parameter set or call preset and achieve auto tour pattern auto scan etc The feature will define the activity when the dome parks Integrated design making it high reliability Auto panning function with 256 preset positions e RS 485 data communication Low noise design With its full 360 horizontal rotation 180 vertical auto flip to follow object and surveillance of any subject is constant and continuous The speed can be adjusted automatically according to the zooming times Auto focus Auto white balance Auto focus lens and auto white balance e BLC Function Multi protocols Pelco P Pelco D Kalate etc Baud rate i
Download Pdf Manuals
Related Search