Onkyo PR-SC5507 User's Manual
Contents
1. Remote ID Nulti Zone HDHI 1 2 3 Tuner 4 5 Network 6 Firmware Update Step 4 Select Via NETOand push ENTER Version Receiver Via NET S Via USB Universal Port ENTER Next Keep the AV receiver s power on while doing the FW update Step gt Select NUpdated and push ENTER O 7 8 Firmare ate Please Check Connection of LAN and do not shutdown power of the receiver while update Ready Updating will begin As the updating progresses the TV screen may disappear depending on the program updated In this case you can see the update progress on the front display of the AV receiver controller The TV screen will reappear when you finish the update and turn on the AV receiver controller Step 6 Message NOK Sum 0 appears on the front display of the AV receiver controller indicating that the update has been completed Alpha numeric characters on the front display are denoted by asterisks ik 2 Suan IFSES SA Step 7 Using the ON STANDBY button on the front panel turn off and on the AV receiver controller Do not use the ON or STANDBY button on the remote controller Congratulations Now you have the latest firmware on your Onkyo AV receiver controller Go to the next page for troubleshooting Troubleshooting Case 1 If No Updated is displayed on the front display of the AV receiver controller as below the firmware has already b2. 07458 U S A Tel 1 800 229 1687 1 201 785 2600 Fax 1 201 785 2650 http www us onkyo com Europe ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 81 42 4401 0 Fax 49 8142 4401 555 http www eu onkyo com China Hong Kong ONKYO CHINA LIMITED Unit 1 amp 12 9 F Ever Gain PlazaTower 1 88 Container Port Road Kwai Chung N T HONG KONG Tel 852 2429 3118 Fax 852 2428 9039 http www onkyochina com Asia Oceania Middle East Africa Please contact an ONKYO distributor referring to Onkyo SUPPORT site lt http www intl onkyo com support local_support index html gt
3. Miscellaneous 8 Remote Controller Setup 9 Lock Setup Step 9 Go to fi7 6 Firmware Updated menu Remote ID Nulti Zone HDI Network 6 Firmware Update 1 2 3 Tuner 4 5 Step 10 Select NVia USBOand push ENTER Version 1151 1203 0511 2102 Receiver via NET Universal Port Updating the Firmware via USB Step 11 Select NUpdated and push ENTER Please check connection of USB and do not shutdown power of the receiver while update Updating will begin As the updating progresses the TV screen may disappear depending on the program updated In this case you can see the update progress on the front display of the AV receiver controller The TV screen will reappear when you finish the update and turn on the AV receiver controller Do not turn off the AV receiver controller and do not remove the USB storage device during updating process Step 12 Message MNOK Sum 0 appears on the front display of the AV receiver controller indicating that the update has been completed Alpha numeric characters on the front display are denoted by asterisks Lik a Bs ara ss IFSE979A Step13 Using the ON STANDBY button on the front panel turn off the AV receiver controller and then remove the USB storage device Do not use the ON or STANDBY button on the remote ontroller Step1 4 Push ON STANDBY to turn on the AV receiver controller Congratulations Now you
4. USB storage device to your PC If there is any data in the USB storage remove it Step 2 Download the firmware file from the Onkyo web site The file name is as follows ONKAVRO001_ zip Extract the zip file that you have downloaded The following three files are created ONKAVRO0001_ of ONKAVRO0001_ of2 ONKAVRO0001_ of3 Step 3 Copy the extracted files to the USB storage device Be careful not to copy the zip file Step 4 Remove the USB storage device from your PC and connect it to the USB port on the AV receiver controller When the AV receiver controller has two USB ports you can use either one Step 5 Make sure your AV receiver controller and TV are turned on If the AV receiver controller is in standby mode push ON STANDBY to light up the front display Step 6 Select the USB input source NNow InitializingO is displayed on the front display and then the name of the USB storage device is displayed It will take 20 to 30 seconds to recognize the USB storage device Step 7 Push RECEIVER followed by SETUP on the remote controller Main menu will be displayed on TV screen Procedures thereafter can also be performed on the AV receiver controller by using its SETUP arrow and ENTER buttons Step 8 Go to fi7 Hardware SetupO menu M E N U Input Output Assign 1 2 Speaker Setup 3 Audio Adjust 4 Source Setup 5 6 Listening Mode Preset
5. have the latest firmware on your Onkyo AV receiver controller Troubleshooting Case 1 If ANo Updated is displayed on the front display of the AV receiver controller as below the firmware has already been updated You do not need to do anything further Case 2 If an error occurs MError Ois displayed on the front display of the AV receiver controller Alphanumeric characters on the front display are denoted by asterisks The example below is displaying error code 0 10 See the following table and take appropriate action Errors during update via USB excluding TX NR1007 Error Code Description 10 20 USB storage device is not detected Make sure the USB flash memory or USB cable is properly connected to the USB port If the USB storage device has its own power supply use it to power the USB storage device An update file is not found in the root folder of the USB storage device or an update file is for other model Retry download following instructions at the support website If the error persists please contact Onkyo Support indicated at the end of this page and provide the error code Retry the update procedure from the beginning If the error persists please contact Onkyo Support indicated at the end of this page and provide the error code ONKYO CORPORATION 2 1 Nisshin cho Neyagawa shi OSAKA 572 8540 JAPAN The Americas ONKYO U S A CORPORATION 18 Park Way Upper Saddle River N J
6. ONKYO Firmware Update for the TX NR1007 3007 5007 We are pleased to offer this firmware update for the best possible performance of your AV Receiver The firmware update may fail if an external HDMI control signal is input during the update procedure Please be sure to turn off the HDMI control function RIHD on your A V receiver before starting the update How to turn off RIHD In the Main menu select 7 Hardware Setup then 7 4 HDMI Set HDMI Control to OFF e Please read the update instructions carefully before beginning e The firmware update should take 30 to 40 minutes Once the update begins don t turn off the power supply to the A V receiver until it is time to restart it e Depending on the conditions of the network a firmware update via a network may take more than one hour or even fail to finish If the update is not completed within two hours turn off the power supply by pushing the ON STANDBY button and then try updating again from the beginning e Updating the firmware and adjusting the settings will be done automatically but may take some time to complete Please follow the procedures as instructed when you update Note that the update may fail or cause problems for your A V receiver if you do any of the following APull out the A V receiver power cord Alnterrupt the power supply to the A V receiver e g if the breaker is tripped or if there is an electrical outage Alnsert or remove the LAN cable
7. SB hubs and USB devices with hub functions are not supported Do not connect your USB mass storage device via a USB hub e USB memory devices with security functions are not supported Updating the Firmware via Network TX NR1007 3007 5007 allow you to update firmware using Network connection on rear panel Tn this procedure on screen display may vary depending on the model Note 1 Make sure your AV receiver controller and TV are turned on and Ethernet cable is connected to rear panel of the AV receiver controller 2 Never unplug or turn off the AV receiver controller during updating process 3 To update the firmware it will take 15 to 25 minutes for TX NR1007 and 30 to 40 minutes for TX NR3007 5007 4 The AV receiver controller will retain all your settings after update is finished Step 1 Push RECEIVER followed by SETUP on the remote controller Main menu will be displayed on TV screen Procedures thereafter can also be performed on the AV receiver controller by using its SETUP arrow and ENTER buttons Step 2 Go to fi7 Hardware SetupO menu MENU Input Output Assign 1 2 Speaker Setup 3 Audio Adjust 4 Source Setup 5 6 Listening Hode Preset Miscellaneous 8 Remote Controller Setup 9 Lock Setup i Step 3 Go to f 6 Firmware UpdateO menu Note that the Firmware Update option will be grayed out for 30 seconds after AV receiver controller is turned on Please wait
8. e from the beginning If the error persists please contact Onkyo Support indicated at the end of this page and provide the error code Case 3 If you do not have a wired connection to the network please contact below ONKYO CORPORATION 2 1 Nisshin cho Neyagawa shi OSAKA 572 8540 JAPAN The Americas ONKYO U S A CORPORATION 18 Park Way Upper Saddle River N J 07458 U S A Tel 1 800 229 1687 1 201 785 2600 Fax 1 201 785 2650 http www us onkyo com Europe ONKYO EUROPE ELECTRONICS GmbH Liegnitzerstrasse 6 82194 Groebenzell GERMANY Tel 49 81 42 4401 0 Fax 49 8142 4401 555 http www eu onkyo com China Hong Kong ONKYO CHINA LIMITED Unit 1 amp 12 9 F Ever Gain PlazaTower 1 88 Container Port Road Kwai Chung N T HONG KONG Tel 852 2429 3118 Fax 852 2428 9039 http www onkyochina com Asia Oceania Middle East Africa Please contact an ONKYO distributor referring to Onkyo SUPPORT site lt http www intl onkyo com support local_support index html gt Updating the Firmware via USB TX NR3007 5007 allow you to update firmware using a USB storage device Tn this procedure on screen display may vary depending on the model Note 1 Never unplug or turn off the AV receiver controller during updating process 2 It will take 30 to 40 minutes to update the firmware 3 The AV receiver controller will retain all your settings after update is finished Step 1 Connect a
9. een updated You do not need to do anything further Case 2 If an error occurs Error Ois displayed on the front display of the AV receiver controller Alphanumeric characters on the front display are denoted by asterisks The example below is displaying error code 0 10 See the following table and take appropriate action Errors during update via Network Error Code Description 10 20 Ethernet cable is not detected Connect the cable properly See the instruction manual for the network connection 1 1 13 Internet connection error Check the following _21 28 items AMake sure IP address subnet mask gateway address and DNS server are configured properly ake sure the router is turned on AMake sure the AV receiver controller and the router are connected with Ethernet cable AMake sure the setup configuration of the router is set properly See the instruction manual of the router Alf your network allows only one client connection and there is any other device already connected the AV receiver controller cannot access the network Consult your Internet Service Provider ISP your modem does not function as a router you will need a router Depending on your network you may need to configure the proxy server if needed See the document provided by your ISP If you still cannot access the Internet DNS or proxy server may be temporarily down Contact your ISP Others Retry the update procedur
10. from a device in your network when updating over a network Alnsert or remove a USB memory device from the A V receiver when updating via USB AOperate components connected to the A V receiver via HDMI such as a TV or a recording device If your A V receiver is damaged for any of the reasons above an Onkyo service center will repair the unit for a fee ONKYO Firmware Update for the TX NR1007 3007 5007 A firmware update is now available through the Network connection on the TX NR1007 3007 and 5007 as well as though the USB connection on the TX NR3007 5007 The 10 16 09 update addresses 1 Improved Internet Radio operability 2 Improved picture quality for iPod iPhone through UP A1 The 11 19 09 update addresses TX NR3007 and 5007 only 1 Improved display of Chinese menus The 12 22 09 update will 1 Improves the functionality of auto speaker setup in Bi amp mode and when a passive subwoofer is connected 2 Improves the operation stability just after power on Depending on the timing no sound comes out 3 Improves on screen display menus The 2 24 10 update will 1 Enhance S N during 24bit 96kHz content playback from USB memory DLNA server 2 Reduce speaker relay switching sound The latest update includes all prior updates We hope you enjoy the improved functionality this update provides to your AV Receiver ONKYO Firmware Update for the TX NR1007 3007 5007 There are the following methods to update the firmwa
11. re via network and via USB storage Please choose either one that suits your condition Before you start carefully read the update procedure To update the firmware it will take 15 to 25 minutes for TX NR1007 and 30 to 40 minutes for TX NR3007 5007 Update via network You need a wired Internet connection to update the firmware For the update procedure please refer to NUpdating the Firmware via Network on page 2 Update via USB storage TX NR3007 and 5007 only Please prepare a USB storage device such as a USB flash memory stick You need at least 32 MB of available space to update the firmware For the update procedure please refer to NUpdating the Firmware via USBOon page 4 Precautions on the USB storage device e The storage media in the USB card reader may not work e If the storage device has been partitioned each section will be treated as an independent device e Ifthe USB mass storage device contains a lot of data the AV receiver controller may take a while to read it e Operation with all USB mass storage devices including the ability to power them is not guaranteed e Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass storage device when that device is used e with the AV receiver controller We recommend that you back up your important music files beforehand e If you connect a USB hard disk drive to the USB port we recommend that you use its AC adapter to power it e U
Download Pdf Manuals
Related Search