Omnitron Systems Technology FlexPoint TR User's Manual
Contents
1. 0 Rii Systems Technology Inc FlexPoint TR User Instructions Description The FlexPoint TR converts between 4 16 Mbps Token Ring twisted pair RJ45 UTP and fiber cabling The following models are described here Model UTP Fiber 4360 Category3 5 Multi mode ST 850 nm 4361 Category 3 5 Singlemode ST 1310 nm Power Adapter Notice 1 When using in a stand alone configuration this product is intended to be used and must be used only with a Listed Direct Plug In Power Unit marked Class 2 and rated at 9Vdc 1 Amp 2 This product should always be used only with Omnitron supplied Power Unit model number 9113 PS WARNING Before inserting the Power Adapter verify that the power on the unit is appropriate for your AC line voltage source Mounting The FlexPoint TR can be wall mounted individually or rack mounted using a 5 position shelf FlexRack 5 or a power redundant FlexPoint Powered Chassis Warning The operating description in this Instruction Manual is for use by qualified personnel only To avoid electrical shock do not perform any servicing of this unit other than that contained in the operating instructions unless you are qualified and certified to do so by Omnitron Systems Technology Inc Caution All user required operations can be performed without opening the unit Never attempt to open or remove the cover or tamper with the unit Warranty This product is warranted to th2. e CA 92618 USA Fax 949 250 6514 Connector FlexPoint Type J TR Fiber Type Model Name Purchase Date Serial Number Company Address Purchased From Address City Zip Code State Zip Code State City Country Country Phone Email Comments and Suggestions Fax Please complete both sides of this form Please complete both sides of this form
3. e original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment TO REGISTER COMPLETE AND MAIL OR FAX THE REGISTRATION PORTION OF THIS INSTRUCTION MANUAL TO THE INDICATED ADDRESS During the warranty period Omnitron will at its option repair or replace a product which is proven to be defective For warranty service the product must be sent to an Omnitron designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s designated US address using Omnitron s standard shipping method Switch Settings RJ45 Cross Over Switch When connecting the UTP to a Ring Out or a Lobe set switch to Straight Through factory setting When connecting to a Ring In or a workstation set it to Cross Over Auto Select Cable Test Switch When in Auto Select factory setting the FlexPoint TR adapts its operation to the type of equipment it is connected to When in Cable Test the FlexPoint supports a fiber or copper media test LED Indicators LED Color Description Power Yellow Power applied Red Error detected Inst Green Inserted successfully into a lobe or Ring In Yellow Media Cable test is enabled Fiber Ready Green Fiber OK UTP Ready Green UTPOK Cable Med
4. ia Test When in Cable Test the FlexPoint TR provides a cabling media test For fiber test provide a connection between the Tx and Rx fiber ports a good fiber turns the Fiber Ready LED ON For UTP test connect a RJ45 cable to a port in a hub a good cable turns the UTP Ready LED ON Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate use and or maintenance of the equipment by Buyer Buyer supplied equipment Buyer supplied interfacing unauthorized modifications or tampering with equipment including removal of equipment cover by personnel not specifically authorized and certified by Omnitron or misuse or operating outside the environmental specification of the product including but not limited to voltage ambient temperature radiation unusual dust etc or improper site preparation or maintenance No other warranty is expressed or implied Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies Omnitron shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any legal theory Form 040 04360 001B 11 07 Installation For all connections attach the fiber between the two FlexPoint TR units first the Fiber Ready LED o
5. n both units should turn ON Select the appropriate Straight Crossed selection for the type of device connecting to on the UTP side 1 Workstation WS to a hub Attach the FlexPoint s UTP to the hub UTP Rdy should go ON Attach the FlexPoint s UTP to the WS Reboot the WS the UTP and Insert LEDs should turn ON 2 Ring Out RO to Ring In RI Attach the RI and RO cables to the hubs Make sure that at least one WS is operational on the ring The UTP Rdy on the RO side FlexPoint TR should turn ON If using active MAUs they might have to be set to 8228 mode 3 Hub MAU to a Switch Attach to the hub s lobe the UTP Rdy LED should turn ON Attach to the switch s port the UTP Rdy and Insert LEDs should turn ON It might be required to set the switch to Cross Over Technical Support For help with this product contact our Tech Support Phone 949 250 6510 Fax 949 250 6514 Address Omnitron Systems Technology Inc 140 Technology Drive 500 Irvine CA 92618 USA Email support omnitron systems com URL http www omnitron systems com Notes User Warranty Registration Please complete both sides and mail or fax this registration form to User Warranty Registration Please complete both sides and mail or fax this form to the address indicated on the other side Omnitron Systems Technology Inc 140 Technology Drive 500 Irvin
Download Pdf Manuals
Related Search