Omnimount TILT-PA User's Manual
Contents
1. Step 10 Adjusting Tilt To adjust tilt Hold A with 3 4 Socket Loosen B with 3 4 Socket Loosen C with 9 16 Socket Position Display Tighten A B amp C We ea Specifications are subject to change without prior notice Every effort has been made to provide accurate and error free assembly and installation Omni Mount Systems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions If OmniMount products are used for purposes other than their original intent OmniMount its distributors and retailers shall not be held responsible or liable for injuries or property damage direct indirect or consequential which may arise from the inability to use this product safely properly and in the manner for which it has been designed and manufac tured Warranty does not apply to products which have been lost damaged by misuse abuse or accident PN 9 05 12 Installation Instructions TPUM 1 Tilting Pipe Adapter e Designed for 26 55 Flat Panel TV s e Maximum Weight Capacity 175 Ibs 79 4 Kg e Connects to 1 5 NPT Pipe Step 8 Attaching the Tilt PA to the Pipe Tighten Here 1 Thread and tighten Tilting Pipe Adapter onto 1 5 NPT Pipe not included 2 Tighten Tilt Tension Nut before attaching Adapter Step 9 Attaching the Adapter and Display to the Pipe Adapter 3 Align the space between the 42. Thread the last Nylock Nuts 2 top Nuts with the grooves in the onto the bottom two Stud Screws Tilting Pipe Adapter and gently lower the Adapter 5 Securely tighten all Nylock Nuts 11 Step 7 Attaching the UM1 to the Display Square Washer Be a By is AS hi Mounting Spacer Screw if needed Na J Y 1 Thread Mounting Screw through Square Washer Rail Spacer 1f needed and into the Display s Mounting Holes NOTE Ensure Retaining Screws are loose enough to allow for adjustment 2 Center the Back Plate on the Display and securely tighten the Retaining Screws and Mounting Screws Important DO NOT over tighten the mounting screws or the display may be damaged NEVER use a power driver to tighten the mounting screws 10 Required Tools Ratchet and 5 16 Deep Socket or 5 16 Open Wrench or Adjustable Spanner Wrench Large Universal Adapter Component Guide 4 Extended Rails eC AG 1 o a Parts List Description gt il hilios Screws M4 x 16m hilips Screws M4 x 36 hilios Screws M4 x 45 3 O 3 hilips Screws M5 x 16m E Philips Screws M5 x 36m hilips Screws M5 x 46m hilios Screws M6 x 16m L hilips Screws M6 x 36m hilios Screws M6 x 46m ae a ee el a3 hilips Screws M8 x 16m Uj U hilips Screws M8 x 36m hilios Screws M8 x 46m M 5 8 Urethane Spacer Z 3 4 Urethane Space
3. horizontal distance between Mounting Holes on Display 2 Thread Flange Nuts 4 3 Thread Nylock Nut 2 onto the onto Stud Screws and tighten two top Stud Screws leaving space using a 5 16 Socket between Nylock and Flange Nuts Step 2 Determine Rail Selection Step 3 Determine Width Configuration Measure the vertical distance between Measure the horizontal distance between Mounting Holes on Display Mounting Holes on Display If distance is greater than 19 48cm See below for Width Configuration details use the supplied Extended Rails Extended Rail Installation only if required 1 Using the Small Hex Wrench unscrew the Slider Retaining Screws 8 Retaining _ Screws 2 Pull to remove the Standard Rail and attached Sliders Range 15 34 40cm to 38 1 2 98cm 3 Using the Small Hex Wrench un screw the Rail Retaining Screws 4 and remove the Standard Rail Narrow Configuration 4 Replace with the Extended Rail insert the Rail Retaining Screws and Rail Retaining tighten ii Screw Holes Range 3 12 9cm to 15 2 39cm
4. r mD A B e D E E E t i D Flange Nut Nylock Jam Nut Step 5 Secure Sliders and Back Plate continued NOTE The outer corners of the Back Plate must al ways be secured Some wide Displays will require the installation of a 6mm Screw and 6mm Lock Nut e not included to secure the 1 X Back Plate hon P Step 6 Hardware Selection Consult the supplied Hardware Cross Reference list and locate the appropriate mounting screws A L for your display Spacers Some displays will require the use of a spacer There are two spacers provided 5 8 16 mm round nose spacer M 3 4 19 mm block spacer N The spacers may be used individually or may be snapped together to create one large stacked spacer The spacers have been designed to snap directly into the mounting rail for ease in handling and also include two different mounting holes to manage the various screw sizes Generally the 5 8 Spacer M is used on displays with slightly curved backs and or recessed mounting lands The 3 4 Spacer N is used on displays with curved backs and Stacked Spacers M amp N will be used on displays with deeply curved backs and or protruding accessories Step 4 Rail Installation Step 1 Set Studs in UM 1 Standard Configuration Narrow Configuration Step 5 Secure Sliders and Back Plate Insert Stud Screws Here 1 Insert Stud Screws 4 into front of Adapter 1 Set Rails to
Download Pdf Manuals
Related Search