Home

Omnia Industries Food Processor Omnia One Multicast Stero Audio Processor with SENSUS User's Manual

1. INTERFACE 2 Livewire DB 9M GPI Interface Connector Powering Up Now you are ready to power up the OmniaONE for the first time Connect AC power to the unit using the appropriate supplied power cable for your location There is no power switch When the OmniaONE is first powered on audio will appear at the analog audio outputs in approximately ten seconds The AES EBU outputs also become usable at this time however full initialization of the AES EBU ports is not complete for several more seconds and a small audio glitch may be heard when the final sample rate converter initialization is complete Once the boot process is finished the following Main Menu will appear Input Output Administrative current preset OmniaONE Multicast Use and Operation Manual Version 0 90 22 Chapter 2 Getting Know Your OmniaONE The OmniaONE User Interface Now that your OmniaONE is rack mounted connected to a program audio source and turned on you re ready to learn how to operate it This chapter covers the Front Panel User Interface your window into the OmniaONE processor A front panel jog wheel with integral push switch LED bargraph peak reading level meters and a backlit LCD display that is switchable between menu and AGC Limiter metering screens make up the primary OmniaONE User Interface The front panel menu access may be password protected to prevent unauthorized tampering with processing or preset
2. OmniaONE Multicast Use and Operation Manual Version 0 90 15 OmniaONE Multicast Use and Operation Manual Version 0 90 16 Chapter 1 Installation Pre Installation Tasks Please take a few minutes to read through this chapter before proceeding with the installation This section offers common procedures for installing your new OmniaONE processor About This Manual This manual is written to cover the OmniaONE Multicast If you are setting up a different version of the OmniaONE please refer to the instruction manual for that product OmniaONE Components By now you ve unpacked the shipping carton to gain access to this manual Now is the time to inspect the OmniaONE unit and its shipping carton for any signs of shipping damage Such damage must be reported to your carrier for any claims The OmniaONE shipping box includes the following components OmniaONE processor OmniaONE Operating Manual in PDF format on Compact Disc Warranty Registration Card Please complete the form and return FAX it to Telos Omnia Two IEC Power Cords one for use in the US and one for use in Europe Vv Vv ON ON Y One each Male and Female XLR to StudioHUB RJ45 adaptor cables AC Power Environment The OmniaONE subsystem is a DSP based microcomputer and therefore requires reasonably clean AC power just as any modern computer system does And even though the OmniaONE power supply is equipped with robust AC transient suppression
3. 12 dBFS or a little higher 7 Connect the audio outputs in a manner that is appropriate for your installation 8 Navigate to the Input Output Output Menu and adjust the appropriate output Level control so that the output level is correct for the equipment that follows the OmniaONE 9 Navigate back to the Main Menu highlight Preset and click Rotate the jog wheel to display the preset appropriate for the program material and bitrate of the following codec and click to select it The OmniaONE Quick Start Setup is now complete Please read on to learn about some of the features that make the OmniaONE Multicast unique beginning with the section Sensus Technology Audio Processing on Page 9 Table Of Contents OmniaONE Multicast Use and Operation Manual Version 0 90 5 Welcome to Omnia O NE 3 OmniaONE Quick Start Setup sete se eaae sete 5 Sensus Technology Audio Processing cssssssssssssssssssssssesssssessesssssssssssssssssssessesseeses 9 9 Codec Provisioning 9 OmniaONE Multicast and Radio soossessoesoossessoesocssesssesoossosssesooesosssesssesoe 10 So what s so smart about Sensus eessessessoesocssessoesocssessoesoossossoesoossocssessoesoe 11 SAFETY INSTRUCTIONS sii pesi espace bas cun tops 12 H
4. In the very near future many low bitrate multicast audio channels might exist To achieve maximum sound quality the kind that attracts and holds listeners those channels will need specialized dynamics processing capable of creating great sound regardless of program content and bitrate They will need Sensus OmniaONE Multicast was designed from the ground up for provisioning audio for codecs operating at these low bitrates With Sensus the innovative algorithm inside OmniaONE Multicast it is now possible to have consistently high audio quality with a minimum of codec induced artifacts OmniaONE Multicast creates highly listenable audio lacking the dull muffled swirley sound usually associated with codecs operated at extremely low bitrates OmniaONE Multicast Use and Operation Manual Version 0 90 10 So what s so smart about Sensus The fact is Sensus is smart In real time it predicts program content that will be troublesome for the codec and by modifying it s own algorithms can make appropriate changes to the program material before it ever reaches the codec The result is consistently high audio quality through a codec based system even at very low 18kbps 21kbps bitrates The human voice is very difficult to code at low bitrates without quality and intelligibility suffering But OmniaONE Multicast with Sensus can generate clean smooth crystal clear audio that s consistently great sounding no matter
5. 2 Back off on the influence of the Limiter stages Reduce the amount of Drive Lower the Release settings in each band to slow down recovery Raise the threshold of the Hold function 3 Ease up on the Wideband AGC sections Reduce the Drive to the Wideband AGC Lower the Release setting to cause it to operate slower Backing off the limiting sections first will allow the processing to still retain a level of loudness while restoring punch and quality Start with reducing the Final Limiter amount in 0 5 dB steps It s surprising how much detail can be restored from such a small change Generally a change in the Final Limiter drive will have the most noticeable effect on quality but it will also affect the relative loudness level too You ll need to find a happy medium that s right for your application Equalization EQ Changes Tailoring the shape of the overall audio spectrum can be done in four different ways gt Adjusting the Drive to the individual bands from within the XOver menu which sets the input levels to the multi band AGC sections Changing the relative amount of Drive to the individual multi band limiters gt Adjusting one or more bands to have faster release times than the others Adjusting the settings within the Mixer four options will provide a noticeable change in EQ and each will have a different character We suggest you use the first two listed options before trying others In ea
6. Omnia ONE Multicast Stereo Audio Processor with SENSUS Installation and Operation Manual Version MC 1 0 September 2007 Applicable to OmniaONE units running version 1 0 14 or higher of the Multicast style software A Telos Company Omnia e 2101 Superior Avenue Cleveland Ohio 44114 USA 1 216 241 7225 e FAX 1 216 241 4103 e Email info gomniaaudio com www omniaaudio com Omnia Europe e Johannistrabe 6 D 85354 Freising Germany TEL 49 8161 42467 e FAX 49 8161 42402 e Email europe omniaaudio com www omniaaudio com OmniaONE Multicast Use and Operation Manual Version 0 90 2 2007 Welcome to Omnia ONE I wish to offer my sincere gratitude on behalf of our company and welcome you to Omnia ONE This manual was assembled by a dedicated team of specialists who were instrumental in the development of our newest product Omnia ONE This is our next step in the never ending quest to build the best signal processor in the world Considerably more powerful than what its small package implies Omnia ONE possesses new hardware and algorithm capabilities that even exceed its predecessors It is also the first audio processor to incorporate LiveWire connectivity enabling linear audio over dedicated networks It s the hottest interconnect technology in the professional audio industry today Broadcasters require a lot of flexibility in an audio processor because transmission systems exist in many
7. OmniaONE Multicast Use and Operation Manual Version 0 90 52 Note measurements made using Bypass mode which is available in the Input Output menu General Audio Specifications Frequency Response 0 50 dB 20 Hz to 20 kHz with high pass filter disabled Distortion Less than 0 05 THD 20 Hz 20 kHz bandwidth Signal Noise Ratio Greater than 100 dB 20 Hz 20 kHz bandwidth referenced to OdBfs The measured noise floor will depend upon the settings of the Input and Output Gain controls and is primarily governed by dynamic range of the Crystal Semiconductor A D Converter which is specified as 2100 dB The dynamic range of the internal digital signal processing chain is gt 144 dB Stereo Separation Greater than 80 dB 20 Hz 20 kHz 90 dB typical Analog Audio Input Left Right Stereo Electronically balanced Input impedance 10k ohms resistive Maximum Input Level 24 dBu Nominal Input Level 4dBu A 12dBu input results in 12dBFS input meter reading with Input Gain set to 0 0dB A OdBu input signal results in a I2dBFS input level when Input Gain is 12dB A D Conversion Crystal Semiconductor 24 bit 128x oversampled delta sigma converter with linear phase anti aliasing filter Pre ADC anti alias filter with high pass filter at 10 Hz Connectors Two EMI suppressed XLR female Pin 1 chassis ground Pin 2 Hot Analog Audio Output Left Right Stereo Electronically balanced Output Impedance 20
8. or from the Main Menu click the Preset Transfer option The Presets screen will appear Main Menu Remote Update Configuration About Logout Any user presets on the OmniaONE will show up as buttons under User Presets inthe Download Presets Download Presets section NOTE The factory presets will Click on the preset name to download it from the audio processor to your computer not show up here and cannot be User Presets downloaded to your computer To download and save a user preset to your computer click on a preset name button and your browser s File Download box To upload a preset from your computer to the audio processor should pop up Upload Presets 1 Use the file entry box or the browse button to give the name of a file on your computer that contains the preset to be uploaded 2 Press the upload button Click the Save button choose 3 The preset will saved on the processor with the same name as the selected the desired folder to save the T HEATED ic 11 29 preset in from the Save As a z 2557 C Documents and Settings Mark Desktop WCSB3 opr Browse upload dialog this may vary with the OS e and click to save the file or to abort Presets are saved as small text based files with the extension To upload a previously saved user preset to the OmniaONE use the file entry box or the browse button to enter t
9. Adjust PEOCES SING 35 CX ect d ED T 35 Pre processtp unos o de EN aca eee av eso ede eI quest 35 Wideband AGC Automatic Gain Control seen 36 PAIN OES 2 as seo Duis se a qu hte 37 AXOVOPAE TOSSOVET exetetons ue ecatectut ena ecce 37 Low 38 Mid Band AGC 39 Pres Band AGC Presence 39 39 Low Band 39 Mid Band Limiter eria 40 Presence 40 High Band 40 B ss Clipper US titu etu RA UM meu a a omnes 40 ln TD EF PS 41 MIO Pio 42 gis rp m e ERR 42 xc rdc cc ITUR 44 liii ma PE 44 Mir Select Meter Seleucus tas apice 45 sede peer vo M M ML A p D ee Mein CU 45 sss 47 Bypass uuo nein ia n hamis E e 48 Save TO Config Juno coca S ups a ate 48 Load IC COUP dure melted ato eue diea e atat d 49 Delete 49 Rename Config NG Leia card vina 49 a D e dad nies d teet caeca oA 50 t 50 About ae ded rta eerte den vo Dire det cai 50 Contrasti ole ieri eaae a a e qua uta S NOR 50 Network Configurati
10. different forms The processor you choose must have the tools to meet those needs Special firmware inside Omnia ONE allows it to meet the challenges of FM AM HD Radio DAB DRM Multicasting Podcasting Netcasting Satcasting and any other form of casting you can think of There s plenty of power inside its little 1U frame so don t let the size fool you It was 1986 in the engineering shop at Z 100 WHTZ FM New York City where our first product was born The Vigilante FM Limiter Twenty one years later and with an incredibly talented team of designers behind it we offer you the newest baby in our ever growing family Omnia ONE Speaking of the team I wish to offer a sincere and heart felt thank you to Rob Dye Bill Mohat Ed Zmuginsky Mark Manolio Ted Alexander David Jablonski Scott Stiefel Sean Overberger Betty Ferrell Steve Kiffmeyer Denny Sanders Marty Sacks Mike Dosch Kirk Harnack Mike Uhl Jim Clemenza Armstrong Marc Johnson Ken Skok and a host of others as you can see it s not just Frank anymore It s a great team of people who always maintain one goal in their minds keep raising the bar Steve Church my partner in crime and founder of Telos first introduced DSP technology to broadcasting in 1985 Our team of DSP gurus is the finest in the audio industry Our own specialized DSP ingenuity has been tremendously beneficial to Omnia s development You have in your possession an incredible audio proc
11. modems traditionally have 25 pin connectors in DCE configuration The OmniaONE has a 9 pin in DTE configuration so the standard 9 pin to 25 pin cable will work The setup and operation of OmniaONE Remote Control is covered in detail in Appendix C OmniaONE Multicast Use and Operation Manual Version 0 90 21 General Purpose Interface GPI DB 9F This DB9 female connector serves as a four input optoisolated interface to the Omnia s internal Trigger Script functions Four of the pins are trigger inputs one is a bias voltage input is a 5V power output and the remaining three are ground The trigger inputs can be used to dynamically alter the OmniaONE s operation in response to logic transitions on the interface connection Virtually any parameter of the Omnia can be controlled using the Trigger Scripts The Trigger Script Interface is a standard component of the OmniaONE Remote Control application Full details including connector pinout are covered in Appendix C starting on Page 63 Please note that the Trigger Script functionality is not yet implemented in the current software but will be available with a free downloadable software update Please check the Omnia website for new software announcements download links and manual updates at http www omniaaudio com OV ses 0000 RS 232 MODEM 210 100
12. octet octet which when entered may appear as a network address such as 192 168 0 200 Subnet Subnet Mask Accepts data in the form of four octets to describe the Ipv4 network subnet mask of the OmniaONE s network interface The entries have the form of octet octet octet octet which when entered may appear as a network address such as 255 255 255 0 Gateway Accepts data in the form of four octets to describe the Ipv4 gateway address assigned to the OmniaONE s network interface The entries have the form of octet octet octet octet which when entered may appear as a network address such as 192 168 0 1 Exit Click on this option to return to the Administrative menu Reboot OmniaONE Multicast Use and Operation Manual Version 0 90 50 Securi lt Exit When selected initiates a complete system reset which includes reloading the internal operating system DSP processing code and values from the current processing preset and IO configuration ty Remote Con Remote Control Enabled Enables remote control access Disabled Disables remote control access Enter Password lt Exit Sets the password for both the front panel and remote control access The default password is omnia all lower case To change the password highlight Enter Password and click The Name field will be automatically highlighted with lt none gt displayed Click and lt none gt will vanish and b
13. top of the applet window will display all of the controls for the OmniaONE s Output menu in the main applet screen Adjustment of the controls works the same way as described above in the Processing section IO To enter the IO Configuration menu click on the IO tab Here you can select a previously saved IO Configuration from the OmniaONE s memory save your changes to an existing IO configuration save your IO settings as a new IO Configuration or delete an existing IO Configuration 9 0 dB TCPAP connection established Output Level Right Trim 10 0 dBu 0 0 dB connection established IO Configur connection established The controls work similarly to the controls in the Preset section above Trigger Scripts e Monol Both MonoR Mono L R R Current preset Mp3 128kb Right Trim 8 Input External Current preset 128kb Select Save Current Delete Config Current preset Mp3_128kb OmniaONE Multicast Use and Operation Manual Version 0 90 67 Please note that Trigger Script functionality is not yet implemented in current software but will be available with a free downloadable software update Please check the Omnia website for new software announcements download links and manual updates at http www omniaaudio com Software Update Procedure Software update
14. Analog AES 3 AES EBU and Livewire outputs Choices governing the selection of the input audio source Analog AES Digital or Livewire and signal mode Stereo or Mono are also found within these submenus These I O settings are generally set once and forget parameters usually adjusted during initial installation and then left alone These I O settings are not saved with a processing preset but can be saved loaded deleted or renamed as I O Configurations using options available in this submenu Please note that Livewire functionality is not yet implemented in the current software but will be available with a free downloadable software update Please check the Omnia website for new software announcements download links and manual updates at http www omniaaudio com Mtr Select Meter Select Selects whether the Input levels Analog Output levels or AES EBU Digital Output levels are displayed on the front panel L amp R LED bargraph meters Input There are nine controls under the heading Input and each will be explained in the order in which they appear in the menu lt Click on this option to return to the Input Output menu Input Src Input Source Allows the selection of Analog or AES EBU digital as the primary input source to the OmniaONE Fover Time Failover Time Failover Time is a feature that when set to a value other than zero disabled allows the OmniaONE to automatically select another in
15. been designed to minimize processing side affects like IM distortion which are usually associated with limiters of this type Using an innovative design that cancels intermodulation products before they develop allows this limiter to sound extremely transparent OmniaONE Multicast Use and Operation Manual Version 0 90 42 This type of peak controller is used instead of a clipper because it does not generate same high levels of harmonic distortion as a Clipper does This distortion would cause added difficulties in a coded audio system because the harmonics generated from the clipping action create added artifacts and workload in the encoder These are especially annoying at high frequencies There are tradeoffs in how each of these peak controllers sound when they are set to produce added loudness When a clipper is pushed the audio may sound edgier This is from the added harmonic content In contrast the look ahead limiter will sound busier or denser when more limiting is applied Drive The Drive control controls the depth of final limiting The amount of gain reduction occurring in the final limiter can be monitored on the Process metering bargraph screen Note however that this meter cannot show extremely fast action in the limiter so your ear must be the final judge LPF Freq Low Pass Filter Frequency This is a key control and is used for matching the audio bandwidth of the processed audio to the bitrate of a followin
16. efficient making it easy to navigate the menu structure of the OmniaONE Processing changes and system adjustments can be quickly made with ease without having to remember multiple controls their positions and what they do in each menu The behavior of the OmniaONE s menu system is consistent across pages and is easy to learn We believe that you will quickly become comfortable with how it works and appreciate its simplicity Clockwise rotation moves the highlighting in a menu downward and increases a value when editing parameters Counterclockwise rotation moves the highlighting in a menu upward and decreases a value when editing parameters Pressing inward on the jog wheel activates the Enter Return or Select button function as follows Pressing the jog wheel inward once also called clicking selects the highlighted menu item or accepts the current parameter value Think of it as a vertical mouse button Pressing and holding the jog wheel in for two seconds will switch the LCD screen to a display of the processing meters so that the gain reduction activity of the AGC and Limiter sections can be monitored Clicking once when the metering screen is displayed will return the display to the menu screen Clockwise rotation moves the highlighting downward through the menu items and increases the value when editing parameters The ENTER RETURN or SELECT button Pressing the jog wheel once selects the highlighted menu item or acce
17. five controls under the heading Output and each will be explained in the order in which they appear in the menu lt Click on this option to return to the Input Output menu Anlg Level Analog Level Adjusts the master audio Output level for the analog outputs which appear on the rear panel XLR male connectors This control adjusts both the left and right stereo channel simultaneously Right Trim Allows a 3dB adjustment of the right analog audio channel gain to correct minor left right balance problems in equipment following the OmniaONE The left channel output gain is not affected by this control and is set using the master Analog Level control previously described AES Level AES EBU Level Adjusts the master audio Output level for the AES Digital Output which appears on the rear panel RJ 45 StudioHUB 9 connector Right Trim Allows a 3dB adjustment of the right digital audio channel gain to correct minor left right balance problems in equipment following the OmniaONE The left channel output gain is not affected by this control and is set using the master AES Level control previously described Samp Rate Sample Rate Configures the Output Sample Rate Options are as follows 48k Slaves the output sample rate to the Omnia s internal 48kHz sample clock To use output sample rates other than 48 kHz Input or External sync must be used OmniaONE Multicast Use and Operation Manual Version 0 90 47
18. never be used for peak control In conventional broadcast applications the method of clipping that was used contributed substantially to the quality vs loudness tradeoff it was a fairly simple two way tug of war In the coded domain the tradeoff is much different it becomes a three way tug of war between quality loudness and audible artifacts Using the rules for conventional processing will cause trouble in a coded audio environment Why Because Codecs complain And they complain in the form of nasty and objectionable artifacts when harmonic or intermodulation IMD distortion is presented to their input In fact dynamic peak limiters employing extremely fast time constants which generates a form of program dependent IMD can easily cause serious trouble for a codec Quality Versus Density The primary trade off between quality and artifacts will be located within the processor s limiter sections With increased depth of limiting intermodulation distortion increases and the fast activity of the limiters causes the audio to sound tight or squashed If limiting is taken to the extreme the sound can be perceived as pumping breathing dense or mushy It can even induce exaggerated swish swirl artifacts from the codec Please remember that the core objective of the OmniaONE Multicast product is maximum intelligibility at low bitrates and processing that creates heavy density can completely mask that effo
19. saving With the cursor in select mode rotate the knob clockwise until Cancel is highlighted and click Delete Preset This option allows a preset to be deleted You may never delete a factory preset An error message will be generated if you attempt to do so You may delete the last preset that was loaded The loaded settings along with any changes will continue to live as the current settings but cannot be recalled again until they are saved To delete a user preset highlight Delete Preset and click Rotate the jog wheel to display the preset to be deleted Click the jog wheel and that preset will be instantly deleted Warning There is no delete confirmation dialog If you wish to exit without deleting a preset rotate the jog wheel clockwise until cancel is displayed in the preset list and click OmniaONE Multicast Use and Operation Manual Version 0 90 34 Rename Preset A preset in the list of stored user presets can be renamed at any time Factory presets cannot be renamed To rename a user preset highlight Rename Preset and click Rotate the jog wheel to display the preset to be renamed and click Edit the preset name as described above in the Save Preset section To exit without renaming the preset rotate the jog wheel until cancel is displayed and click lt Exit Click on this option to return to the Main Menu Adjust Processing This submenu allows changes to be made in any of the OmniaONE s
20. service the Return Authorization number must be written prominently on or near the shipping label on the box OmniaONE Multicast Use and Operation Manual Version 0 90 60 Warranty This Warranty covers the Products which are defined as the various audio equipment parts software and accessories manufactured sold and or distributed by TLS Corp d b a Omnia hereinafter Omnia With the exception of software only items the Products are warranted to be free from defects in material and workmanship for a period of two years from the date of receipt by the end user Software only items are warranted to be free from defects in material and workmanship for a period of 90 days from the date of receipt by the end user This warranty is void if the Products are subject to Acts of God including without limitation lightning improper installation or misuse including without limitation the failure to use telephone and power line surge protection devices accident neglect or other damage EXCEPT FOR THE ABOVE STATED WARRANTY OMNIA MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE In no event will Omnia its employees agents or authorized dealers be liable for incidental or consequential damages or for loss damage or expense directly or indirectly arising from the use of any of the Products or the inability of the end user to use any of the Products eit
21. the Operating Guide for additional installation and setup information Refer to the following illustration for the location of the various controls and connectors associated with the installation Headphone Jack Headphone Level Control Jog Wheel Main Menu G R Metering LCD Display Level Meters Y ANALOG INPUTS ANALOG OUTPUTS AES OUT ins v e j PM V BA ue E R 2X MOOEM 4 210100 5 LEFT LEFT v IGHT 1 SCAINPUT COMP 2 MAMZOUT AES INSYNC ENNE C 1 Install the OmniaONE in the equipment rack using at least two rack screws If only two screws are used they MUST be installed in the bottom holes of the rack ears 2 Connect AC power to the unit there is no power switch 3 Connect the audio inputs that are appropriate for your installation 4 Navigate to the Input Output Meter Select setting and select Input 5 Navigate to the Input Output Input Input Src setting and select the Analog or AES EBU input as appropriate for your installation If your audio source is providing an audio feed you should then see meter activity on the LED bargraph meters 6 While driving the inputs with typical program material at normal operating level navigate back up to the Input Output Input menu by highlighting and clicking on the lt EXIT option and adjust the appropriate input Level control until the peak reading input bargraph meters are peaking up to at least 15 and up to
22. to scroll clockwise past the blank space just after the last character of the preset name or select mode will be cancelled If this happens simply rotate the knob counter clockwise until Name is highlighted and click to re enter select mode When you reach the character you want to edit click This puts the cursor in edit mode You can now change that character by scrolling through the character list with the knob When the desired character is found click This will return the cursor to select mode and you can again turn the knob to select the next character to edit To delete a character Select the character to be deleted click choose the symbol and click again to delete that character Characters can only be deleted one at a time To insert a character between 2 existing characters Select the character just after where the new character is to be inserted click choose the symbol and click again The new character appears Now rotate the knob to select the desired character for it and click to accept Note that this inserts a new character before the one selected and keeps the originally selected character intact as what it was before choosing When you are finished simply rotate the knob clockwise with the cursor in select mode until the Save button is highlighted and click to save the preset Your new user preset will now appear in the Preset menu To cancel at any time without
23. we recommend that an online style non switching type Uninterruptible Power Supply UPS with transient surge suppression be employed At transmitter sites there can be heavy transients on the power lines as well as significant surges introduced into the power system by frequent lighting strikes These are unwelcome power line events and can damage even the most robust equipment Therefore you should give the AC power environment and installation practices thorough consideration before plugging in the OmniaONE or any other microcomputer based equipment A White Paper by one of our Support Engineers can be found on the Telos Systems website at the URL listed below It details proper grounding and contains links to some surge suppression products for both the power mains and the often neglected telephone Ethernet and ISDN line connections that can and do conduct powerful surges into the equipment http www telos systems com techtalk surge htm OmniaONE Multicast Use and Operation Manual Version 0 90 17 Installation amp Connections Throughout this section reference is made to software parameters These are part of the User Interface which is covered in detail in Chapter 2 Rack Mounting The OmniaONE requires one RU 1 75 44 45 mm of rack space Rack mount the unit using four rack screws If only two screws are going to be used they should be in the bottom holes in the Omnia front panel No other two screw mounti
24. 638 4CEE9A 4FAGBD Waiting for child 160 DSP 3 DSP 0 31000000 DSP 0 31000000 222BAD D9FBFF 001800 002800 2 1 E2FE4A ABSFFA 6D1D43 Waiting for child 162 Last update log Shell invoked to run file var tmp CF update update Command bin sh Command cd var tmp Command tar xf CF update tar CF update boot0 jffs img Command flashw f CF update boot0 jffs img var update bank Command xtool usleep 2000000 Command tar xf CF update tar CF update verify Verifying Installation Command echo Verifying Installation Verifing new software Electrical and mechanical safety note When the Omnia is operated with its chassis top cover removed you are exposed to potentially lethal voltages Before attempting to make voltage measurements be forewarned that the power supply heat sinks are connected to the AC power line Avoid these areas whenever the AC power cable is attached to the Omnia Never attempt to make measurements when the power supply s safety cover is removed When reinstalling the top cover make certain that all thirty screws are replaced and that they are tightened to a snug fit Operating the unit with its cover removed or without all of the retaining screws will void your warranty and may compromise the ability of the Omnia to operate in high RF environments Narrowing down problems OmniaONE Multicast Use and Operation Manual Version 0 90 58 When actually troubleshooting your OmniaONE try
25. AZARD WARNING LABELS eee ee ee ere eene etos tenete etae eae ta aeta sete etae eaae epa ta 13 Manual Update Notification ctore enn voa nean n nonna nean ako inen uana aia a enu Y vorn aun 15 eaten NEIN 17 Fascihi ell miMICCI Cic 17 About This Manuals NER 17 ConmpoOtlents 17 Power Environment T 17 Installation amp Connections ion aeternis evo vo toa sb Poo ruso Ores tpe yel kae uso PERRO EU 18 Rear Panel Connections 19 Analog Audio Inputs and Outputs essent 19 Note About Relative Phase 19 AES EBU Digital Input AES EBU External Sync Input and AES EBU Output20 Ethernet dabat odisea dua E 20 RS 232 Modem Connection 9 21 General Purpose Interface GPI 9 22 Powerin 22 Chapter 2 Getting To Know Your 23 The OmniaONE User Interface e eeeeee ee 23 Headphone Level Control etaed nt d te t ma en redo o d 23 Level Meters amp Processing Bargraphs 23 Audio Displays scias det ep 24 Processing Meter Display 23e deutet o Pri
26. Input Slaves the output sample rate to the sample rate present on the Omnia s AES digital input Synchronization is possible over a range of sample rates from 32kHz to 96kHz Ext External Slaves the output sample rate to the sample rate present on the Omnia s AES SYNC input Synchronization is possible over a range of sample rates from 32kHz to 96kHz lt Click on this option to return to the Input Output menu Bypass Process This is the normal default setting where all processing will be active Bypass This setting will bypass all processing for test purposes Save IO Config VO settings are those that affect the audio input and output configuration and allow correct interface with the rest of the airchain external equipment Save IO Config Saves all user settings within the Input Output menu to the system s non volatile memory as named configuration presets Use this to save your I O configuration as the system default or save more than one configuration if the unit will be used with different external equipment configurations These saved configurations can be recalled using the Load IO Config option To save an IO configuration proceed as follows Highlight Save IO Config and click Name will be highlighted and the Name field will display lt gt if no previous configurations have been saved or it will automatically display the currently loaded configuration s name If you wish to o
27. MOVE ANY COVER OR PANEL NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THE OMNIA TO RAIN OR MOISTURE The Exclamation Point The Lightning Flash With symbol within an Arrowhead symbol within an equilateral triangle alerts equilateral triangle alerts the the user to the presence of user to the presence of non important operating and insulated dangerous voltages maintenance servicing within the product s enclosure instructions in product that may be of sufficient literature and instruction magnitude to constitute a manuals risk of electric shock WARNING This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions in this manual it may cause interference to radio communications The device has been formally submitted for testing and found to comply with the limits for a Class B computing device pursuant to subpart J of Part 15 FCC Rules and has been designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area may cause interference and the user and at his expense will be required to take any measures required to correct interference CANADA WARNING This digital apparatus does not exceed the Class B limits for radio noise emissions set out in the Radio Interference Re
28. MPORTANT NOTE Always set the low pass filter frequency so that it is at or below half the sampling frequency of the encoder This must be done in order to comply with the Nyquist Theorem Doing so will achieve the highest perceived audio quality OmniaONE Multicast Use and Operation Manual Version 0 90 43 The Nyquist Theorem states that the maximum frequency that may be applied to sampled data system is one half the sampling frequency When signals beyond half the sampling frequency are present aliasing occurs which causes the appearance of an inverted spectral image of the audio spectrum to be folded around the lower side of the sampling frequency it is actually folded symmetrically around both upper and lower sidebands of the sample frequency however in professional audio applications only the lower sideband is usually audible When this occurs the original signals and the aliases are not separable by any means Level 12 44 52 84 20 3 64 Frequency kHz Aliasing example Sample Frequency 32 kHz Signal Frequencies 0 20 kHz New Images 12 52 kHz and 44 84 kHz lt Exit Click on this option to return to the Adjust Processing submenu lt Exit Click on this option to return to the Processing menu Input Output OmniaONE Multicast Use and Operation Manual Version 0 90 44 This submenu provides level adjustments for the audio inputs and absolute peak operating level of
29. REEN shrink tubing is used for AES IN and the female XLR lead with the RED shrink tubing is used for AES EXTERNAL SYNC IN Ethernet Connection The RJ 45 10BaseT 100BaseT Ethernet Livewire I O jack can be used simultaneously for both TCP IP based remote control of your OmniaONE and audio input output to your existing Livewire network Please note that the Livewire functionality is not yet implemented in the current software but will be available with a free downloadable software update Please check the Omnia website for new software announcements download links and manual updates at http www omniaaudio com 10 100 INTERFACE N a Ethernet 10 100 Remote and Livewire I O OmniaONE Multicast Use and Operation Manual Version 0 90 20 5 232 Modem Connection DB 9M This DB9 male connector can be used to connect an external dialup modem for a bi directional computer remote control connection NOTE This connector is for a remote control external modem connection only Please see Appendix B for information on how to use a terminal program along with an internal RS 232 connector for troubleshooting purposes RS 232 Modem Port NOTE You must use a standard straight through serial cable and not a null modem cable when connecting the RS 232 connector of the Omnia and the external modem Typically this would be 9 pin to 25 pin cable External
30. acts are tamed There are 8 available adjustment frequencies between 13kHz and 1kHz Sen Level Sensus Level Sets the amount of codec conditioning to be applied to the audio Increasing the setting adds more SENSUS control Extreme settings those high enough to cause noticeable dulling of the program material are unnecessary and will not further improve the audio quality through the codec Ster Link Stereo Link lt Exit Final Limit Under most operating modes this can be set to Low or OFF The link control allows dynamic coupling of the stereo to mono ratio When set to OFF the Sensus function will only affect mono material or signals that are common to the Left Right channels under stereo conditions Higher settings of the link adjustment may offer assistance with low bitrates and an inefficient codec NOTE While the Sensus Frequency and Sensus Level controls are algorithmically independent from the standpoint of a codec they work in tandem to reduce coding artifacts through a bit reduced system Always start with the LPF Low Pass Filter see Final Limit below set as recommended by the table in that section Then adjust Sensus Frequency and Sensus Level controls until satisfactory results are achieved through the codec Click on this option to return to the Adjust Processing submenu The OmniaONE Multicast employs a final look ahead limiter to provide absolute precision peak control This limiter has
31. akers Also this algorithm which is mathematically derived will contribute lower midrange IMD components to the spectrum So live voice vocals and solo instruments that are present along with strong bass in the program material will sound cleaner yet will still create an in your face effect to the low end When both the Girth Clip and Tight Clip settings are both set to OFF the Bass Clipper is effectively bypassed Both algorithms can be ON at the same time but this is not recommended Tight Clip When ON this Bass Clipper style is a straightforward hard limiter that will create deep sub harmonic effect to the audio The drawback is that it can generate intermodulation distortion in the Final Limiter and increase artifacts in the codec employed after the Omnia ONE Multicast When both the Girth Clip and Tight Clip settings are both set to OFF the Bass Clipper is effectively bypassed Both algorithms can be ON at the same time but this is not recommended Filtering Adjusts the amount of time aligned low pass filtering after the Bass Clipper Normally this extra filtering is not needed but if heavy amounts of Bass Clipping are being used especially when using the Tight Bass Clipper style the filtering can help reduce distortion or artifacts and can provide a rounder and smoother bass sound lt Click on this option to return to the Adjust Processing submenu Mixer Low Band Adjusts the output leve
32. al reference Automatically accepts sample rates between 32kHz and 96kHz Connector EMI suppressed RJ 45 female pinned according to StudioHub standards Transformer isolated balanced and floating according to AES3 standard Remote Control 10 100BaseT Ethernet standard web based protocol and additional TCP IP connections Direct Serial RS 232 at 9 600 19 200 or 57 600 baud no handshaking Hayes command set compatible external modem Connectors RS 232 port EMI suppressed DB 9 female connector Ethernet Industry standard EMI suppressed RJ 45 connector GPI Interface Configuration Four fully optoisolated inputs Software sensing of both go high and go low transitions Inputs are protected to 2000 V AC DC Connector EMI suppressed DB 9 male Control User programmable using built in Trigger Script feature in included OmniaONE Remote Control software Virtually any parameter of the OmniaONE may be programmed through this interface feature Power Requirements Voltage 100 250 VAC 47 63 Hz Less than 25 VA Power Connector EMI suppressed IEC male Detachable 3 wire power cords supplied for US and European use OmniaONE Multicast Use and Operation Manual Version 0 90 54 Power Supply Internal Overvoltage and short circuit protected Meets EN55022 EN55011 Level B Conducted Emissions EN61000 4 2 3 4 5 6 level 3 immunity compliant Full international safety approval CE marked Environmental Oper
33. annel gain can be adjusted over a range of plus and minus 3 dB relative to the gain setting of the left channel gt To return to the top level of the Main Menu rotate the jog wheel to highlight Exit and click Repeat until the top level Main Menu is reached of the OmniaONE s software parameters are set in a similar fashion using the jog wheel to scroll through menu items Clicking a highlighted item selects it when that item is a control the jog wheel adjusts the value or level Clicking accepts the value or level and returns the jog wheel to Select Mode Note Altering any processing or gain parameter will instantly be reflected in a change in the OmniaONE s output characteristics because adjustments occur in real time Therefore any adjustments you make will be instantly heard as they occur OmniaONE Multicast Use and Operation Manual Version 0 90 27 OmniaONE Multicast Use and Operation Manual Version 0 90 28 Chapter 3 Getting The Sound You Want In general applications requiring audio processing prior to a codec don t rely heavily on absolute loudness for their overall success Loudness is still important of course you do want to be heard but it is not the most important thing It has been well established that codecs generally do not like extremely processed audio applied to their inputs because with very dense audio there are fewer opportunities to hide coding artifacts these opportunities to hide c
34. ating Temperature 32 to 122 deg F 0 to 50 deg C for all operating voltage ranges Humidity 0 95 RH non condensing Dimensions 19 wide x 1 75 high x 16 deep 48 26cm wide x 13 335 cm high x 40 64 cm deep including connectors Unit requires one EIA rack space for mounting Shipping Weight 10 165 4 54 kg StudioHub is a registered trademark of Radio Systems Telos Omnia Research and Development is constantly working to improve the quality of our products Actual specifications are subject to change or improvement without notice OmniaONE Multicast Use and Operation Manual Version 0 90 55 Appendix B Troubleshooting Service Warranty Operational problems with the OmniaONE can sometimes be diagnosed using the RS 232 serial port located inside the top cover of the unit NOTE This is not the rear panel RS 232 MODEM connector and a common terminal communications program Detailed information about the Omnia s boot up progress may be observed at this internal RS 232 port as well as viewing of any error messages that may be encountered This chapter explains the various boot up and error messages that may be encountered while troubleshooting the unit We ll cover some basic OmniaONE Multicast Use and Operation Manual Version 0 90 56 troubleshooting techniques for isolating possible OmniaONE problems in the field and also how to obtain help repair service from Omnia To take complete advantage of this f
35. cast_0 94 9 oup with size 1161489 bytes has been successfully uploaded Installation is now in progress This will take a moment during which time the unit must not be interrupted Click here to monitor the progress of the update The update monitor page will allow you to determine when the update is complete and then select the new software and reboot the unit or resume the current software OmniaONE following Update Initiated screen should appear Now the software bank that is not currently in use will be updated with the new file Read the Update Initiated screen and then click on the link Click here to monitor the progress of the update The Installation Progress Monitor screen should appear Main Menu Remote Update Configuration About Logout Installation Progress Monitor Please wait for installation to complete You can determine when the installation is complete by monitoring the status log below The message Update successful will be displayed upon successful completion The log will automatically refresh every 8 seconds If the log is not visible below you can monitor the status page In this case you must use your browser s reload button to manually refresh the page and the back button to return to this page when installation is complete Execution Finished Exiting Waiting for child 86 STATUS Verifying update integrity and Uncompressing Waiting for child 88 STATUS Verifying pr
36. ce oai e o ira tures Ebo 24 Usine The Jog Wheel m er et hase vae uU ead rona Pb NU Nap s 25 Main iro tp de isum m tu c E 26 User Interface Tutorial Input Source Selection and Peak Level Setting 26 Proper Setting of Input Levels aisi eate Iti train ao id tete 27 Chapter 3 Getting The Sound You Want eee eee ee eee eee ee eene seen eese 29 A Word About Density Clarity and Intelligibility 29 Quality Versus Density 29 Increasing Density Loudness cere e ee eene eren eee enne eene eee ea sete ta seta 30 Adding More Detail When Loudness Isn t The Last Word 31 Equalization EQ Changes sscscisoccsssesnssenesssssesseenceoseseesesentevecesesvocssesevecesessusecareenees 31 Thunder BASS PT o IN 32 Chapter 4 Main Menu Selections e eee ee e eerte ee ee eese sete sese sete sete ao s sean ee ena 33 OmniaONE Multicast Use and Operation Manual Version 0 90 6 erae eee e 33 PrOCESSITE vea ER oaristo EYES 33 Save gro e satus can RE T 34 Delete Preset ost en ero o b utem d ea tu Leto 34 eoe ws detenta em eS edi ec 35 sole ai RPE eae Re ER OMT Foe RENE ATI m A RU cd irc m 35
37. ch case the EQ change you make is followed by a dynamically controlled stage so the subsequent AGC or Limiter will counter any excessive EQ adjustments OmniaONE Multicast Use and Operation Manual Version 0 90 31 The last option adjusting the Mixer is designed to provide a final minor trim to audio spectrum Since this stage is after all of the dynamic multi band AGC and Peak Limiting a radical change in level in the Mixer could result in excessive look ahead final limiting in that band s frequency range We suggest that any changes implemented here be limited to about 0 5 dB to 0 7 dB of boost maximum Alternately a decrease in mix levels can be done in any desired amount and without fear of final limiter overdrive Thunder Bass OmniaONE Multicast has the power to shake the walls with low end If your source material has it OmniaONE Multicast can expose that deep bass and do it with muscle Tailoring Thunder Bass for more dominance is simple and is done by adjusting the following parameters and in the order listed 1 Increase the amount of Bass boost in the Enhance section 2 Increase the Drive to Low Frequency Limiter 3 Increase the Release setting in the Low Frequency Limiter 4 Increase the Drive to the Bass Clipper Just as in the section on overdoing processing again moderation is the key If all of the above changes are made in unison there is a possibility of severe low frequency buildup This would unbalanc
38. click again to delete that character Characters can only be deleted one at a time To insert a character between 2 existing characters Select the character just after where the new character is to be inserted click choose the symbol and click again The new character appears Now rotate the knob to select the desired character for it and click to accept Note that this inserts a new character before the one selected and keeps the originally selected character intact as what it was before choosing When you are finished simply rotate the knob clockwise with the cursor in select mode until the Save button is highlighted and click to save the configuration preset To cancel at any time without saving With the cursor in select mode rotate the knob clockwise until Cancel is highlighted and click Load IO Config This option allows you to select and load a previously saved IO configuration To load a saved IO configuration highlight Load IO Config and click Rotate the jog wheel until the desired IO configuration is displayed and click To exit without loading a configuration rotate the jog wheel until cancel is displayed and click Delete IO Config This option allows a previously saved IO configuration to be deleted To delete an IO configuration highlight Delete IO Config and click Rotate the jog wheel to display the IO configuration to be deleted Click the jog wheel and that named configuration will be
39. dress some of the challenges of provisioning audio for coding This hurdle existed because the codec adapts to the incoming program so as to generate the least amount of output data representing the input audio causing the sonic artifacts generated by the process to continually change Unless the audio processor can predict these changing characteristics of the codec it can t possibly create output audio that is perfectly tailored for the coding process Conventional processors utilize rather simplistic high frequency limiters and fixed low pass filtering that does not change with the program material When these less intelligent processors feed a codec the audio might sound acceptable one moment and offensive the next Because they cannot know what the codec will do next the result is over compensated dull and lifeless audio audio that still contains objectionable codec generated artifacts OmniaONE Multicast and Radio The advent of HD Radio has introduced the capability to transmit multiple program streams or Multicast within a single 96kbps digital broadcast data channel To facilitate this multicast relies on the use of codecs with comparatively low bitrates A broadcaster can choose to transmit a number of multicast channels and select the bitrate for each one However the more multicast channels there are the lower the bitrate each channel must have in order for them to all fit within the total available bandwidth
40. e original factory presets can never be deleted or renamed We will discuss the Save Delete Rename and Exit options first before delving into the details of the Adjust Processing menu OmniaONE Multicast Use and Operation Manual Version 0 90 33 Save Preset This option saves any changes you have made to the currently running preset into the OmniaONE s non volatile memory Changes can be saved over an existing user preset without renaming it or as a new user preset with a new name You may not save a factory preset over itself with the same name and attempting this will generate the error message Cannot overwrite factory preset Save preset with new name Presets can contain up to 10 characters To save your changes proceed as follows Highlight Save Preset and click Name will be highlighted and the Name field will automatically display the existing preset name If you wish to overwrite this existing preset with your changes just rotate the jog wheel clockwise to highlight the Save button and click Your changes will be saved to the existing preset If instead you wish to save your changes as a new user preset with a different name click the jog wheel while Name is highlighted and the editing cursor will appear highlighting the first character of the existing preset name This is select mode At this point you can scroll left and right through the text by rotating the jog wheel knob Be careful not
41. e replaced by the editing cursor Rotating the jog wheel clockwise will scroll through the capital letters of the English alphabet first Rotating it counter clockwise will scroll through the numeric characters first and then through the lower case English alphabet In between is a blank space with an underscore character Once the desired character is found click to accept that character Click again to display the editing cursor and add the next character the same way When you are finished and the new password is complete do not click again to display the editing cursor Instead rotate the jog wheel to highlight the Save button and click to save the password If you wish to cancel without saving the new password rotate the jog wheel to highlight Cancel click to accept and the operation will be cancelled The existing password will be retained Click on this option to return to the Administrative menu Click on this option to return to the Main Menu Lock Front Panel This is a feature that enables you to lock the front panel in order to prevent inadvertent or unauthorized tampering with control settings and processing parameters Access via user password is the only way to access the front panel menus when it has been locked via a user assigned password To lock the front panel highlight Lock Front Panel and click A warning message will be displayed Locking front panel requires password to regain access OmniaONE Mu
42. e the audio spectrum and produce the illusion of lost presence and high frequencies Generally an increase in the Bass boost alone will provide a sufficient enhancement to the low end Bass adjustments should typically be done after selecting the preset you wish to use and the low pass filter that is appropriate for the codec to be used Adjusting processing for coded audio is different than conventional radio While many of the dynamics functions are the same i e compression limiting EQ etc please consider that the audio processor is a tool to improve the performance of the codec This is especially true at lower bitrates When making processing adjustments try to avoid building too much density in the presence and high frequency ranges Density in this spectra cause codec efficiency to become reduced and artifacts increased Even though Sensus technology is applied downstream from the main processing and will improve system performance remember that the processor is a sum of its collective dynamics parts and the result will be based on the cumulative effect of all of the settings When adjustments are being made pay particular attention to program content that segues from music to voice and back again If everything is working properly the vocal quality should not change due to the coding process If this is noticed try reducing the Sensus function value by one adjustment click and then reevaluate OmniaONE Multicast Use and Ope
43. ed the new version should appear as the Running Software version Banko Version Multicast 1 0 10 9 Bank 1 Version FM 1 0 14 siu FM 1 0 14 10 You may now close your browser The software update is complete OmniaONE Multicast Use and Operation Manual Version 0 90 71
44. er one of the menus and then click lt Exit Or enter the Preset menu rotate Jog Wheel to the right and select Cancel To save changes to the currently running user preset as shown in the gray status bar at the bottom of the remote window click the Save Current button It does not matter what preset is highlighted in the preset list The currently running preset will be updated with your changes To save the current settings as a new preset click the Save Current As button A new applet window will open with a dialog box where you can type the name of the new preset For convenience there is also a dropdown menu where you can select an existing preset name to start with Once the new preset name appears as desired click the Save button The new preset will be saved to the unit and will appear in the preset list To cancel without saving simply close the applet window OmniaONE Multicast Use and Operation Manual Version 0 90 64 To delete a preset click Delete Preset button new applet window will open with a preset list Highlight the preset to be deleted in this preset list and click the Delete button The preset will be instantly deleted from the unit and the preset list To cancel without deleting any presets simply close the applet window Preset Transfer User Presets can be downloaded to and uploaded from your computer From the top menu in the Remote screen click Presets
45. es in audio level and higher numbers equate to faster response times Faster attack times reduce the transient nature of the input audio while slower attack times improve it Extremely slow attack times must be used with caution because allowances must be made in later stages to not overload them during the time when the broadband AGC is adjusting the level downwards AGC AGC Release The release control adjusts how fast the AGC recovers from periods of more gain reduction when the input audio levels fall Faster release times higher numbers result in a more dense sound Even though the Omnia uses program controlled release algorithms setting the control for extremely fast release times can result in pumping Gt Thresh Gate Threshold When the input audio falls below a certain level the gain control action of the AGC stage is frozen by the gate The level at which this freeze or hold takes place is controlled by the setting of the Gate Threshold control Higher numbers cause the gate to activate at higher audio levels In most applications this control should be adjusted to cause gating action to occur when the input audio falls about 20dB below nominal The action of gate also prevents noise rush up during periods of no audio or during pauses in speech RTZ Speed Return To Zero Speed RTZ stands for Return To Zero What RTZ does is return the gain of the WB AGC section to an internally determined amount of gain reductio
46. essor Also you have the full support of our entire organization standing behind the product If you have feedback or even a new idea we re here to listen Customers like you offer us valuable feedback After all it s feedback like yours that helped us introduce the original Omnia FM and then take the industry by storm Our quest today just as it has been all along is to continue to be the audio processing brand leader To borrow a phrase from my old stomping grounds Z 100 in New York City Omnia went from worst to first in the minds and ears of radio broadcasters We are honored equally humbled to say the least and grateful to you our customers for helping us make that happen Omnia processors have been installed by tens of thousands of broadcasters throughout the world and I am overwhelmed when I look at the list of our end users So it s to you our loyal customers and friends that I say Thank You To Great Sounding Audio the World over a des Frank Foti President Omnia Audio OmniaONE Multicast Use and Operation Manual Version 0 90 3 OmniaONE Multicast Use and Operation Manual Version 0 90 4 OmniaONE Quick Start Setup We know that you re probably in a hurry to begin using your new OmniaONE Multicast If you have technical expertise and previous knowledge of audio processor fundamentals using our Nine Point Quick Start will get you up and running as quickly as possible Please refer to the remainder of
47. g codec Setting this control to the proper bandwidth for the codec s settings will ensure minimal side effects and aliasing distortion products from the codec process The available settings are 4kHz 6kHz 8kHz 10kHz 13kHz 16kHz and 22kHz These are the frequencies at which the low pass filter reaches a minimum of 100dB of attenuation One of the most important features that an audio processor for codec provisioning must have is a high quality low overshoot low pass filter after the final peak control stage OmniaONE Multicast offers this feature as a low pass output filter that can be set to one of seven stop band frequencies Each of the filters possess minimal passband ripple and are phase linear below cutoff Response in the filter stop bands is greater than 100dB The following chart recommends low pass filter settings that in our experience best complement the AAC SBR MP3 and Windows Media WMA codecs They were derived through thousands of hours of critical listening and we feel they are very good starting points for achieving the best overall sound although you may use other settings that you feel are more appropriate for your particular codec application AAC SBR Output LPF MP3 jOutput LPF_ WMA Output LPF 24kbps BkHz 24kbps 6kHz 24kbps 5kHz 6kHz 32kbps 10kHz 32kbps ___ 48kbps 13kHz 16kHz48kbps 8kHz 10kHz 48kbps 10kHz 13kHz 64kbps 16kHz 64kbps 10kHz 16kHz 64kbps 13kHz 16kHz I
48. gulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limits applicables aux brouillage radioelectrique edicte par le ministere des Communications de Canada OmniaONE Multicast Use and Operation Manual Version 0 90 13 CONFORMANCE This device complies with requirements of the Council Directives 93 68 EEC CE Marking 73 23 EEC Safety low voltage directive 89 336 EEC electromagnetic compatibility Conformity is declared to those standards EN50081 1 EN50082 1 LITHIUM BATTERY CAUTION There is a danger of explosion if the internal battery is replaced incorrectly or shorted Replace the battery only with same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions USE OF SHIELDED CABLING In order to conform to the CE requirements for High Frequency radiation shielded cables must be used for all audio and data connections NOTE When the unit is operated in an extremely high RF environment it may be helpful to connect cable shields to the XLR connector terminal that connects cable shield to chassis ground not to pin 1 Additionally a 0 01uF capacitor connected between XLR pin 1 and the chassis terminal may be helpful in some instances RoHS COMPLIANCE The RoHS Directive stands for the restriction of the use of certain hazardous substances in electrica
49. h fast Attack times can cause the limiter to hang after a transient failing to fully recover and punching hole in its band of frequencies LFLim Hold Low Frequency Limiter Hold Threshold During operation of the limiter the algorithm is watching for very small decreases in audio level such as what occurs right after a sudden peak When this occurs the limiter release is temporarily stopped The result is a drastic reduction in intermodulation distortion and a more open sound even though the audio is still quite dense The level at which the hold takes place is controlled by the setting of the hold Thresh control Higher numbers cause the hold to activate at higher audio levels The action of limiter hold also works in conjunction with the preceding AGC gates to reduce noise rush up during periods of no audio or pauses in speech Lim Thresh Limiter Threshold This control adjusts the threshold level of where limiting begins Lower settings will increase the amount of limiting and decrease the level going to the following Bass Clipper low band only or Final Limiter stage Conversely higher settings will raise the limit threshold causing less limiting but feeding more level into the following Bass Clipper low band only or Final Limiter stage Normally we recommend leaving the Limiter Thresholds at the factory setting lt Click on this option to return to the Adjust Processing submenu Mid Band Limiter See descriptio
50. h this freeze or hold takes place is controlled by the setting of the Gate Threshold control Higher numbers cause the gate to activate at higher audio levels In most applications this control should be adjusted to cause gating action to occur when the input audio falls about 20dB below nominal The action of gate also prevents noise rush up during periods of no audio or during pauses in speech OmniaONE Multicast Use and Operation Manual Version 0 90 38 RTZ Speed Return To Zero Speed RTZ stands for Return To Zero What RTZ does is return the gain of the AGC band to the selected amount of gain reduction See RTZ Level below in the absence of audio RTZ speed controls how fast this adjustment takes place i e how long it takes the AGC to move to the target RTZ level RTZ Lvl Return To Zero Level This control adjusts the gain level to be achieved by the AGC section during lapses in audio The primary purpose of RTZ is to prevent the AGC from increasing the gain unnecessarily during lapses in audio which would result in an increase in noise level lt Click on this option to return to the Adjust Processing submenu Mid Band AGC See description of settings for Low Band AGC Pres Band AGC Presence Band AGC See description of settings for Low Band AGC High Band AGC See description of settings for Low Band AGC Low Band Limiter LFLim Drv Low Frequency Limiter Drive Adjusts the drive level to the individ
51. he preset file name to be uploaded and press the Upload button The preset will be saved to the OmniaONE with the same name as the selected file minus the opr extension NOTE In the current software after uploading a preset with the remote that preset s name will not appear in the preset list on the front panel of the OmniaONE unit until a preset save rename or delete operation is performed from the front panel itself So after uploading a preset to the unit from the remote simply save any preset as a new name rename a preset or delete a preset using the front panel jog wheel and the uploaded preset should then show up in the front panel s preset list OmniaONE Multicast Use and Operation Manual Version 0 90 65 Processing Click on the Processing tab and the block diagram will appear Processing E xover Limit TCPAP connection established Current preset Mp Each block is a button that can be clicked to open a new applet window containing the controls for that processing block Any number of processing block windows may be opened at the same time When opened they will minimize automatically to the taskbar Windows OS this may vary on other operating systems We will use the WB AGC processing block as our example for adjusting the controls in a processing block Gate Thresh Attack When you open a processing block window t
52. he Left and Right channel input levels gt Rotate the jog wheel clockwise to highlight Input and click gt Rotate the jog wheel to highlight Level and click the jog wheel to select the control Rotate the jog wheel CW to increase the input level Rotate the jog wheel CCW to decrease the input level This control adjusts both channels together in precise 0 5 dB steps The gain in dB is shown to the right of the control Watch the Left and Right channel LED meters while adjusting per the following paragraph below Proper Setting of Input Levels With normal program audio levels applied a correct input level setting will result in peak indications on the L amp R LED meters achieving between 15 and 12 dBFS or a little higher This gain setting corresponds to system headroom of about 12 15 dB You may adjust the input level for more headroom if you wish by lowering the levels to increase headroom Setting the input level for higher meter indications less headroom is strongly discouraged unless there is another level control device prior to the OmniaONE that will keep the input levels from reaching the maximum digital level of 0 dBFS gt Once the desired level setting is reached click the jog wheel to accept that value This returns the jog wheel to Select Mode gt You may highlight and click Right Trim to adjust its gain separately from the left channel if the input source is not well balanced In this mode the right ch
53. he channel the OmniaONE Multicast is processing and then altering it using the controls in the Processing menu you may change the sound of a preset and then save it with your changes as a user preset for either immediate use or later recall By alternately loading different presets you may compare the sound between them Here in the Preset menu you may select and load presets to use but not save delete or rename them Those operations may be accomplished from within the Processing menu Processing Highlighting and clicking Processing from the main menu opens up the Processing menu that contains these options Adjust Processing Save Preset Delete Preset Rename Preset and Exit This is where the sound of the OmniaONE can be fine tuned and customized Once customized this is also where your user presets are saved deleted and renamed Each submenu in the Adjust Processing menu can be highlighted clicked to open and the individual controls within can be adjusted to individual taste Since you cannot build a preset from scratch a factory preset must be used as a starting point for creating your signature sound Each processor parameter may be adjusted to taste as required Once the processing is adjusted the Save Preset function is used to store your changes as a new user preset to non volatile internal memory Using the Delete Preset and Rename Preset options existing user presets may be deleted from memory or renamed as needed Th
54. he first knob will be highlighted in red indicating it is ready to be adjusted with the current setting enclosed in brackets To select a different knob to adjust simply click on O Med it The new knob will be highlighted in red with its Fast current setting enclosed in brackets Java Applet Window Once highlighted there are two ways to adjust a knob 1 Move the mouse cursor over the desired knob click and hold the left mouse button and drag the mouse either to the left to lower the setting or to the right to raise the setting When the desired setting is reached release the mouse button 2 Move the mouse cursor over the desired knob and rotate the scroll wheel on your mouse if so equipped downward to lower the setting or upward to raise the setting When you turn a knob the brackets will disappear but will remain with the original setting for reference Once you click on a different knob or close the window your new setting will become the bracketed setting To change the radio button settings simply click once on the button or name of the desired setting and release In OmniaONE Multicast Use and Operation Manual Version 0 90 66 Clicking on the In tab will display all of the controls for the OmniaONE s Input menu in the main applet screen Adjustment of the controls works the same way as described above in the Processing section Out Clicking on the Out tab at the
55. he following parameters in the AGC Increase the Drive to the AGC sections Increase the Release settings to make the bands operate faster 2 Modify the Multiband Limiter sections Increase the Drive to the Limiter section Increase the Release settings to make the bands operate faster Note that slowing the time by using a lower setting can help make things sound more natural when faster Release times are used But be careful not to allow too many fast transients through to the final limiter section 3 Setthe Hold threshold in each band to a lower value 4 A combination of all of the above yes it sounds crazy but it s true Always resist the temptation to make too many changes at once because it then becomes difficult to determine why or why not an adjustment made the change you hear It is better to make small adjustments to a small number of controls at a time and then listen to the result with a wide variety of program material Once you have satisfactory results in one area like overall density you can then move the focus to the next area that you feel needs more tweaking Don t be afraid to experiment with different styles of processing Our presets are good starting points and are not restricted to any particular format because of their name OmniaONE Multicast Use and Operation Manual Version 0 90 30 Some users prefer their processing to be perceptibly loud but very dynamic While this may not res
56. her separately or in combination with other equipment or materials or from any other cause In order to invoke this Warranty Omnia must receive notice of a warranty claim within the above stated warranty period and Omnia must authorize warranty coverage If Omnia authorizes the performance of warranty service the defective Product must be delivered shipping prepaid to Omnia 2101 Superior Avenue Cleveland Ohio 44114 Omnia at its option will either repair or replace the Products and such action shall be the full extent of Omnia s obligation under this Warranty After the Products are repaired or replaced Omnia will return them to the party that sent the Products and Omnia will pay for the cost of shipping Omnia s authorized dealers are not authorized to assume for Omnia any additional obligations or liabilities in connection with the dealers sale of the Products Omnia products are to be used with registered protective interface devices that satisfy regulatory requirements in their country of use OmniaONE Multicast Use and Operation Manual Version 0 90 61 OmniaONE Multicast Use and Operation Manual Version 0 90 62 Appendix Remote Control and Software Update Procedure Remote Control ANALOG OUT AES OUT Preset Processing CI CIO gt P cosa c c Limit connection established Current preset Mp3 128 The above screenshot shows the Proces
57. ics link option in the Utilities section at the bottom of the Configuration screen Utilities Restart the audio processor This interrupts audio Resume a suspended system Useful after an aborted update Troubleshooting and diagnostic information A report similar to the below will be generated You can select the text and then copy and paste into an email or email a screen shot to if requested to do so by your Telos Omnia factory Customer Support Engineer For contact information see Obtaining Service on Page 60 Factory Diagnositics Process Status PID Uid Size State Command 1 user 0 5 init 2 user 0 5 kflushd 3 user 0 5 nfsiod 4 user 0 5 nfsiod 5 user 0 3 nfsiod 6 user 0 5 nfsiod 50 ttySO user 0 5 bin sh 51 user 0 5 bin inetd 52 user 0 R bin boa 45 user 0 5 src 4l user 0 5 olua base server luac 43 user 0 5 tcp server 44 user 0 5 meter server 4546 46 user 0 T dsp int usr dsp fm 4b 367 47 user 0 5 led meters 48 user 0 5 input sel 49 user 0 5 omnial 53 user 0 5 bin syslogd n 153 user 0 3 usr cgi bin omnia cgi 154 user 0 5 sh c ps 155 user 0 ps Waiting for child 154 DSP Communications tests DSP 0 DSP 0 1000000 DSP 0 01000000 222BAD E007DB 001800 002800 E154C9 7868AC 3AIBD3 064330 Waiting for child 156 DSP1 DSP 0 11000000 DSP 0 11000000 222BAD AASCB1 001800 002800 690C1D D937DC 591675 84A1A7 Waiting for child 158 DSP2 DSP Ox21000000 DSP 0 21000000 222BAD 75 857 F974F5 002820 9F3ACE 1
58. imiters can lead to a wall of sound effect that can cause the program material to sound smashed This can also cause additional artifacts to be generated in the following codec Lower settings will reduce the density providing a more open natural and dynamic sound lt Click on this option to return to the Adjust Processing submenu Low Band AGC Attack The attack control adjusts how fast the AGC responds to sudden increases in audio level and higher numbers equate to faster response times Faster attack times reduce the transient nature of the input audio while slower attack times improve it Extremely slow attack times must be used with caution so as not to allow later stages to be overloaded during the time when the AGC is adjusting the level downwards Likewise extremely fast attack times especially when combined with very slow release times can punch holes or overreact to the band of audio being processed Release The release control adjusts how fast the AGC recovers from periods of more gain reduction when the input audio levels fall Faster release times higher numbers result in a more dense sound Even though the Omnia uses program controlled release algorithms setting the control for extremely fast release times can result in pumping Gt Thresh Gate Threshold When the input audio falls below a certain level the gain control action of the AGC stage is frozen by the gate The level at whic
59. ing Overview Until now digital signal processing has been a more precise numeric implementation of well known analog methods Even relatively recently designed digital audio processors couldn t veer too far from the comparatively simplistic concepts that analog dynamics processing had utilized until now Extremely high power DSP chips have become available and at relatively low cost and they make it possible to build smarter and more complex processing algorithms that were too difficult or impossible or too expensive to do in the past Running on a platform of the latest high power DSP chips the OmniaONE and our new Sensus technology takes digital dynamics processing into a completely new frontier Instead of the two dimensional static processing architecture of the past Sensus enables the audio processor to modify its own architecture in real time and in response to ever changing program content Simply stated Sensus has the ability to sense what must be done to a signal in order to best tailor it for the following codec As program content changes it rearranges the algorithms to accomplish this goal The uniqueness of the Sensus technology makes it highly suitable not only for codec pre conditioning or provisioning but also for a range of other highly specialized signal processing challenges The following is a discussion of how Sensus technology can be applied to a coded audio environment Codec Provisioni
60. instantly deleted To exit without deleting a saved configuration rotate the jog wheel until cancel is displayed and click Rename IO Config This option allows a previously saved IO configuration to be renamed To rename an IO configuration highlight Rename IO Config and click Rotate the jog wheel to display the IO configuration to be renamed and click Enter the new configuration name as described above in the Save IO Config section To exit without renaming a configuration rotate the jog wheel until cancel is displayed and click OmniaONE Multicast Use and Operation Manual Version 0 90 49 lt Exit Click on this option to return to the Main Menu Administrative Several maintenance and utility functions are found in this submenu including various Security options to prevent tampering by unauthorized personnel TCP IP networking parameters and other system wide parameters About Presents a dialog displaying the OmniaONE software style firmware release version and front panel software version currently active in the unit Contrast Adjusts the contrast of the front panel LCD display to optimize it for various viewing angles Network Configuration Allows customization of the network interface configuration Available parameters are IP IP Address Accepts data in the form of four octets to describe the Ipv4 network address assigned to the OmniaONE s network interface The entries have the form of octet octet
61. l and electronic equipment This Directive bans the placing on the European market of new electrical and electronic equipment containing more than agreed levels of lead cadmium mercury hexavalent chromium polybrominated biphenyl PBB and polybrominated diphenyl ether PBDE flame retardants OmniaONE Multicast is in compliance with the EU RoHS Directive ROHS COMPLIANT lead free OmniaONE Multicast Use and Operation Manual Version 0 90 14 Manual Update Notification Audio Processing a unique art form that we take very seriously As part of our dedication to the science of audio processing we will continue to improve and update the Omnia product and its documentation based on our ongoing research real world field experience and the valued input from our many thousands of loyal customers We strongly encourage our customers to visit our Omnia website for product enhancement announcements software updates updated user manuals and customer support bulletins The following URLs have been included for your convenience Manual Updates http www omniaaudio com support manuals htm Frequently Asked Questions FAQ http www omniaaudio com support fag htm Tech Tips amp Support Bulletins http www omniaaudio com tech tips htm Software Upgrades amp Remote Software http www omniaaudio com support updates htm White Papers amp Technical Discussions http www omniaaudio com tech default htm
62. l of the low band limiter into the following Final Limiter stage Higher numbers result in more low frequencies bass but too much mix level can make the following final limiter work unnecessarily hard Mid Band Adjusts the output level of the mid band limiter into the following Final Limiter stage Higher numbers result in more midrange but too much mix level can make the following final limiter work unnecessarily hard Presence Band Adjusts the output level of the presence band limiter into the following Final Limiter stage Higher numbers result in more presence but too much mix level can make the following final limiter work unnecessarily hard OmniaONE Multicast Use and Operation Manual Version 0 90 41 Hi Band lt Sensus Adjusts the output level of the high band limiter into the overall mix Higher numbers result in more high frequencies and too much mix level can make the following final limiter work unnecessarily hard Click on this option to return to the Adjust Processing submenu See a descriptive overview of the Sensus function Sensus Technology Audio Processingx3 beginning on Page 9 Sen Freq Sensus Frequency This sets the range where the SENSUS function begins its magic For example a setting of 5kHz will program the SENSUS algorithm to focus on frequencies of 5kHz and higher You should start with the 13kHz setting and then select lower frequency settings until any coding artif
63. lticast Use and Operation Manual Version 0 90 51 Rotate jog wheel and click to lock the front panel or to return to the Main Menu without locking the front panel The factory default password is omnia all lower case Changing the password is done using the Enter Password option in the Security section above Unlocking the Front Panel To unlock the front panel rotate the jog wheel to highlight Password click twice and enter will be replaced by the editing cursor Rotating the jog wheel clockwise will scroll through the capital letters of the English alphabet first Rotating it counter clockwise will scroll through the numeric characters first and then through the lower case English alphabet Once the desired character is found click to accept that character rotate the jog wheel one notch clockwise to advance the cursor to the next position and click again to display the editing cursor Enter the next character of the password the same way When you have entered the last character of the password do not click twice to display the editing cursor Instead click only once to accept the final character and rotate the jog wheel to highlight the button Click on OK to accept If the password was correct the screen should display the Main Menu Appendix A Performance Specifications OmniaONE Multicast As of January 2007 Version 0 9 Software
64. ly installed software bank after a software update in order for the new software to run Bank 0 Version Multicast 1 0 10 S Bank 1 Version FM 1 0 14 Version Multicast 1 0 10 Apply In this example the new software has been uploaded to Bank 1 OmniaONE Multicast Use and Operation Manual Version 0 90 70 You will notice that previous software Bank 0 in this case is still selected and running You can choose to change to the other bank to activate the new software or keep running the current software and reboot later NOTE A reboot is required to activate the new software and this will interrupt the audio From the Select Software Bank section click the radio button of the Bank that contains the new software version and click the Apply button In this example we decided to go ahead and activate the new software so we clicked on the Bank 1 radio button and then clicked Apply Main Menu Update Configuration About Logout Software bank 1 selected Return to Configuration Reboot Processor To activate the selected bank now click the Reboot Processor link option The processor will reboot and the new software will be activated To continue running the previous version click the Return to Configuration link option instead When you are ready to activate the new version return to the Configuration page and repeat Step 9 Once activat
65. mniaONE Multicast Use and Operation Manual Version 0 90 18 Rear Panel Connections ANALOG INPUTS ANALOG OUTPUTS LEFT RIGHT LEFT FOGHT SCANPUT COMP AES OUT UNIVERSAL POWER OUT 90340 VAC 5 232 lt gt 10 100 tWMZOUT AESm SYNC INTERFACE rewire A A C OmniaONE Rear Panel Analog Audio Inputs and Outputs Balanced XLR type connectors are used as input connectors for the analog audio Both analog and digital input sources may be connected simultaneously however only the input source that has been selected is active Analog Digital Livewire Input source selection is done through the Source software parameter setting in the Input Output Input Menu The stereo analog inputs are designed for standard 4dBu balanced signals Pin 2 is Hot Individual Left and Right analog outputs are available on two male XLR jacks Pin 2 is Hot ANALOG INPUTS y ay 4 Telos Company 2101 SUPERIOR AVENUE CLEVELAND OHIO 44114 MADE USA y LEFT omniaaudio com A Note About Relative Phase ANALOG OUTPUTS If the relative phase of your installation including the OmniaONE differs from that of your existing system your announcers may feel that they sound weird in their headphones If this occurs then the relative phase of the processor is 180 degrees from what your air talent is used to To remedy this you can either reverse the pola
66. n in the absence of audio RTZ speed controls how fast this adjustment takes place i e how long it takes the AGC to move to the target RTZ platform level Exit Click on this option to return to the Adjust Processing submenu OmniaONE Multicast Use and Operation Manual Version 0 90 36 Enhancers Deep Bass Adds girth to the audio by enhancing very low frequencies such as kick drum fundamentals or very low bass notes that may be present in the input audio program Phat Bass An Omnia exclusive Phat Bass adds harmonic overtones to the lower bass frequencies The addition of these overtones causes small speakers to seem to produce bass response that they are not actually capable of producing because the human brain equates the presence of low frequency harmonics to the missing fundamentals that the small speaker is unable to reproduce On systems with larger speakers the effect of Phat Bass becomes subtler because the extended frequency response of those systems allows the fundamentals of the low notes to be heard masking the added harmonics contributed by Phat Bass Be careful though too much Phat Bass boost can lead to excessive gain reduction in the lower AGC bands and may cause muddiness with certain program material A little goes a long way Warmth lt This Warm Bass EQ is a shelf boost at 150 Hz Warmth EQ compensates for program material that is naturally lacking in upper bass fullness Be judicio
67. n of settings for Low Band Limiter Presence Band Limiter See description of settings for Low Band Limiter High Band Limiter See description of settings for Low Band Limiter Bass Clipper The Bass Clipper operates between the output of the Low Band Limiter and the Low Band Mixer the output of which feeds the Final Limiter Its purpose is to keep excessive bass out of the Final Limiter reducing IM intermodulation distortion while keeping and even enhancing the bass punch of the program material There are two different Bass Clipper styles available Described below Clip Drv Bass Clipper Drive Adjusts the drive level to the Bass Clipper over a range of 6 dB Higher settings will increase the amount of Bass Clipping increasing bass density while keeping the actual peak bass level fed OmniaONE Multicast Use and Operation Manual Version 0 90 40 to Mixer same This allows you to reduce Low Band Mixer control to reduce IM distortion in the Final Limiter without reducing the amount of perceived bass in the program material Be careful Too much clipping by the Bass Clipper can soften bass punch It may also be heard as rattling sound in the bass or cause additional artifacts in the codec following the Omnia ONE Multicast Girth Clip When ON this Bass Clipper style is designed to create a phatter effect to low frequencies and it will help create the illusion of more bass on smaller spe
68. n the Login button Or simply press Enter Login Please enter password to login Password Login 4 The Main Menu should appear Click on the Firmware Update link option 5 The Confirm Firmware Update screen should appear with the following warning Performing an update requires the controls and meters for the audio processor to be stopped On air audio will not be interrupted during the update However a reboot is required to activate the new software and this will interrupt the audio At the end of the process you will have the option to change the current boot bank to activate the new software and reboot or to keep running the current software and reboot later Do you want to continue the update process If you would like to proceed after reading the warning message click the Continue button and the Update File dialog should appear Update file Browse Update 6 Click the Browse button locate the software update file downloaded and saved to your computer in Step 1 double click it so that it appears in the Update File box then click the Update button The file will now be uploaded to the OmniaONE This may take up to 5 minutes A progress bar may or may not appear depending on the browser being used but once the file is successfully uploaded to the Main Menu Remote Update Configuration About Logout Update Initiated The file E Downloads muti
69. nd the cart combination to overturn Servicing Refer all servicing of the product to qualified service personnel Damage Requiring Service Unplug this product from the AC wall outlet and refer servicing to qualified service personnel under the following conditions When the AC plug is damaged If liquid has been spilled or objects have fallen into the equipment If the product has been exposed to rain or moisture If the product does not operate normally following operating instructions If the product has been dropped or damaged in any way When the product exhibits a distinct change in performance This indicates a need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any repairs to this product ask the service technician to perform safety checks to determine that the product is in safe operating condition Cleaning Do not use liquid cleaners or aerosol cleaners Use only a damp cloth for cleaning OmniaONE Multicast Use and Operation Manual Version 0 90 12 HAZARD WARNING LABELS WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT RE
70. ng The codec is now a common denominator in the world of audio and broadcasting Digital broadcasting HDTV HD Radio DAB DRM podcasting webcasting cellcasting and downloadable music files all employ a form of codec based data compression in order to minimize the bandwidth required to transmit data The necessarily low bitrates utilized by these mediums presents a tough challenge for any audio processor used prior to a codec Traditional dynamics processors were designed to fulfill the requirements of a medium where the functions were generally static That is they were well suited to the rather simplistic peak control OmniaONE Multicast Use and Operation Manual Version 0 90 9 and bandwidth limiting methods that were required for analog broadcasting as well as for signal normalization techniques used in recording and mastering Audio codecs on the other hand are moving targets each codec algorithm has its own set of artifacts So not only does the sonic quality vary depending on the algorithm and bitrate used but more importantly they vary in their ability to mask their own coding action This is why we call it a moving target and is why conventional audio processors fall short in a coded audio environment and can actually make coding artifacts worse due to their inability to adapt appropriately to the changing operation of the codec as the program content changes Prior art in audio dynamics processing could only ad
71. ng arrangement will prevent distortion of the front panel Adequate ventilation should be provided and it is always good engineering practice to allow one blank rack space immediately above and below the Omnia especially if equipment generating significant heat is located below the unit You may install IRU 1 75 vented or solid rack panels to fill these spaces The processor should be installed into a properly grounded 19 equipment rack Refer to Chapter X OmniaONE User Tips for additional considerations on where to physically locate your processor AC Power Connection UNIVERSAL POWER INPUT 90 240 VAC 1A 5A 50 60HZ OmniaONE utilizes an un switched EMI filtered IEC power entry module OmniaONE s automatic voltage sensing high efficiency switching power supply allows it to operate on AC mains voltages from 100 to 240 VAC and from source frequencies of either 50 or 60 Hz In the USA plug the provided IEC type AC power cord into the unit and then into a grounded AC outlet Outside of the USA you must use the appropriate power cord that complies with local electrical regulations After power is first applied to the OmniaONE the LCD screen the in and out LED s and rightmost segments of the LED bargraph meters should light After about 20 seconds the LCD screen should show OmniaONE Multicast and at about 30 seconds the Main Menu should appear Once the Main Menu appears the unit is ready for use O
72. oding action are commonly referred to as codec entropy If you believe that you re in a density war and you feel a need to react we can provide some suggestions that should help Conversely if you have the luxury to strive for increased sound quality we ve got suggestions for you too There will always be a subjective compromise whenever there is a desire to shift the processing priority from the highest quality setting to those generating the highest loudness OmniaONE Multicast has been designed to minimize the trade offs between quality and loudness and we recommend that before starting the process of cranking it up try to determine beforehand what sonic characteristics might be lacking In many cases it s not just about increasing the drive to the limiters Instead it can be as non intuitive as creating the illusion of greater loudness by changing something simple like a time constant Sometimes the old adage of less is more really applies Please give the following content some thought as it may assist you in developing an overall fine tuning plan if you feel changes beyond our factory presets are justified A Word About Density Clarity and Intelligibility Processing for the coded audio world is quite a bit different than what is done for FM Stereo and AM There are two significant differences and both impact the overall sound of a coded transmission First there is no pre emphasis network in coded audio Second clipping should
73. oduct ID Waiting for child 90 Waiting for child 92 STATUS Installing Waiting for child 94 Waiting for child 103 Update successful After the installation is complete you can use the links below to select the new software and reboot or to resume the previously installed software If the new software is not selected now it can be selected at a later time on the Configuration page Status Page Select New Software Configuration Page Resume Current Software The log box on this screen will be automatically refreshed every 8 seconds NOTE If the log box does not show up on your browser you can click on the Status Page link option to display an alternate status log In this case you must use your browser s Reload button to manually refresh the Status page then the Back button to return to this page when installation is complete When Update Successful appears at the bottom of the log as shown the update has been installed and is ready to be selected Once the Update Successful message appears at the bottom of the log click on the link Select New Software Configuration Page Scroll down the Configuration page to find the Select Software Bank section Select Software Bank Choose the software bank that will run the next time that the audio processor is re booted This will have no effect until re boot which can be done below or by cycling power Note that you must select the new
74. ohms Minimum load Impedance 600 ohms Output Level adjustable from 2 dBu to 22dBu peak in 0 1dB steps D A Conversion Crystal Semiconductor CS4390 24 bit 128x oversampled Connectors Two EMI suppressed XLR male Pin 1 chassis ground Pin 2 Hot Digital Audio Input Configuration Two channel stereo per AES3 standard via CS8420 Digital Audio Transceiver with 24 bit resolution Software selection of stereo mono from left mono from right or mono from sum Automatically accepts sample rates between 24 kHz and 96 kHz OmniaONE Multicast Use and Operation Manual Version 0 90 53 Connector EMI suppressed RJ 45 female pinned according to StudioHub standards Transformer isolated balanced and floating according to AES3 standard Digital Audio Output Stereo per AES3 standard Digital Output sample rate software selectable for internal 48kHz synchronize to AES input or synchronize to auxiliary AES sync input per AES 11 DARS Connector EMI suppressed RJ 45 female according to StudioHub standards Transformer isolated balanced and floating according to AES3 standard Digital Output Level 22 0 to 0 0 dBFS peak software adjustable in 0 14 steps Digital Sync Input Output sample rate can be synchronized to the signal present on the AES EBU input or to the AES3 signal applied to the Ext Sync connector External Sync Range Accepts 32kHz to 96 kHz for synchronization of the Digital Output signal to an extern
75. on oin ci Det us c ot acess 50 CIDE Rc eA atn attonitus dieta oaa em E 50 RNS CU in AMNEM TN M pM 51 OBI n soe E HE E A T EE 51 Lock Front Pane 51 Unlocking the Front Panel iei eet eet e d Ne 52 Appendix A Performance Specifications sesssesssecesocesooecsoeessecssocesocesoosssoessseessocesoose 52 OmniaONE Multicast Use and Operation Manual Version 0 90 7 Appendix B 8 96 Diagnostics and Error ceres ecce eren ee eee enne eese ense sese es ssseeeeeessee 97 Electrical and mechanical safety note eee e eee ee ecce ee eee eee ee eene eee seeee 99 Narrowing down reno enorm be aie ne rtr Petre eto u ere DO Obtaining SEP VICE er World Wade Webs is 60 Via E Mail MUN 60 Via Phone amp Mail USA and non European 60 Warranty d gie dolet ALEESQ Appendix C Remote Control and Software Update Procedure 63 Remote OO E ek 67 Software Update Procedure e eee eee eee eere ee ee eese eo eee es sseees sese 08 OmniaONE Multicast Use and Operation Manual Version 0 90 8 nic Muttic ast Sensus Technology Audio Process
76. on a more consistent output from the band Mid Drive Adjusts the amount of gain reduction in the Mid Band AGC Higher numbers result in more drive and because of the increased compression a more consistent output from the band Pres Drive OmniaONE Multicast Use and Operation Manual Version 0 90 37 Adjusts amount of gain reduction in Presence Band AGC Higher numbers result in more drive and because of the increased compression a more consistent output from the band Hi Drive Adjusts the amount of gain reduction in the High Band AGC Higher numbers result in more drive and because of the increased compression a more consistent output from the band OV AGC Drv Overall Multiband AGC Drive Adjusts the overall amount of drive to all four bands of the 4 Band AGC section simultaneously over a 6 dB range Higher settings will increase the overall amount of compression and the dynamic EQ effect of the 4 Band AGC This can make the program material sound more consistent Be careful though because too much compression can cause the program material to sound less natural and cause low level noise in the program material to be brought up OV Lim Drv Overall Limiter Drive Adjusts the overall amount of drive to all four bands of the multiband Limiter section simultaneously over a 6 dB range Higher settings will increase density This can increase loudness but be careful because too much gain reduction in the l
77. on to the user interface Start from the Main Menu as displayed when the unit is first turned on The first exercise changes a parameter selection the Input Source selection gt Rotate the jog wheel to highlight Input Output gt Click the jog wheel push on the wheel once until a click is felt and release to bring up the Input Output menu gt Rotate the jog wheel to highlight Input and click gt Rotate the jog wheel to highlight Input Src and click OmniaONE Multicast Use and Operation Manual Version 0 90 26 gt The factory default selection for Input Source is Analog To change the input selection to AES EBU digital rotate the jog wheel until AES EBU is displayed and click If you are using the analog inputs rotate the jog wheel to display Analog and click to reselect the analog inputs gt Toreturn to the top level of the Main Menu rotate the jog wheel to highlight lt EXIT and click Repeat until the top level Main Menu is reached NOTE Many of the OmniaONE s menus have an EXIT selection at both the top and bottom of the menu The next exercise adjusts a parameter that uses a value the analog master input level setting The Main Menu display should still be showing on the LCD screen If not click the jog wheel to display it Highlight Input Output and click Highlight Mtr Select click rotate the jog wheel until Input is displayed and click This sets the first 2 LED meters to monitor t
78. onfigured as follows STEREO Factory default Left and Right input channels are routed to the left and right inputs to the DSP processing chain Mono L Configures the DSP processing chain to have both the Left and Right internal channels fed only from the Left Channel of the input source selected Note that this selection is active in all sources selected as Primary and Secondary Failover audio sources Mono R Configures the DSP processing chain to have both the Left and Right internal channels fed only from the Right Channel of the input source selected Note that this selection is active in all sources selected as Primary and Secondary Failover audio sources OmniaONE Multicast Use and Operation Manual Version 0 90 46 Mono L R Configures the DSP processing chain to have both the and Right internal channels fed from the sum of the Left Channel and Right Channels of the input source selected Note that this selection is active in all sources selected as Primary and Secondary Failover audio sources SWAP Configures the DSP processing chain to swap the Left and Right internal channels that is the DSP Left Channel is fed from Right Channel input and the DSP Right Channel is fed from the Left Channel input Note that this selection is active in all sources selected as Primary and Secondary Failover audio sources lt Click on this option to return to the Input Output menu Output There are
79. ontacting Omnia Customer Support please have the serial number of the unit located a barcode sticker on the rear panel in this format 0218WXXXX and a description of the symptoms problems ready for the technician e All units being returned to for service MUST have a Return Authorization RA number assigned to them first Units that are returned without a RA number will experience delays in service e Return the Omnia in its original shipping carton if possible For best treatment shipping the Omnia in its original factory box protects it as well as possible Damage caused by improper packaging is not covered under your warranty Note To ensure prompt service the Return Authorization number must be written prominently on or near the shipping label on the box Via the World Wide Web The Omnia Web site has a wide variety of information that may be useful for product support applications information software updates etc The URL is http www omniaaudio com Via E Mail The customer service e mail address for Omnia is support omniaaudio com Phone amp Mail USA and non European Countries Customer service is available by telephone Monday Friday between 9 00 A M and 6 00 P M USA Eastern time zone Phone 1 216 241 7225 Fax 1 216 241 4103 Shipping Information Telos Omnia 2101 Superior Avenue Cleveland Ohio 44114 USA ATTN To the RA number obtained from Omnia Customer Service Note To ensure prompt
80. ounds that have no acoustically relevant information Phase Rot Phase Rotator The phase rotator improves waveform symmetry for program material that is highly asymmetrical in nature Examples of such programming are the human voice and sources with non sinusoidal waveforms such as certain string and wind instruments as well as certain sounds created by electronic synthesizers By removing waveform asymmetry from the input program material cleaner processing results because any limiting that occurs is able to work equally on both positive and negative excursions of the audio waveform OmniaONE Multicast Use and Operation Manual Version 0 90 35 Wideband AGC Automatic Gain Control The wideband AGC rides the incoming audio levels like an automatic hand on the fader keeping the average level more consistent for the following 4 Band AGC stage enabling it to stay in its sweet spot WB AGC Bypass Engage The wideband Automatic Gain Control AGC stage can be bypassed if desired although more consistency is achieved when this stage is used AGC Drv AGC Drive This control adjusts the amount of drive to the wideband AGC stage Increasing the drive causes deeper compression to be achieved and deeper compression allows quieter passages in the input audio to be raised further than if lesser drive and less compression was used AGC Att AGC Attack The attack control adjusts how fast the AGC responds to sudden increas
81. pload presets to from local machine Update software installation Configure system and networking See information about the Processor and Remote Logout of the system and return to login screen You may see the Java logo and then the main Remote Control screen should appear If audio is present on the OmniaONE s inputs you should see the meters moving along with the audio A small amount of flickering is normal as the meter information is updated but if it is excessive or the meters are not moving smoothly check your network connection and or update your video card drivers or settings There are 5 tabs in the Multicast style Remote Control applet Preset Processing In Out and Preset To enter the Preset menu click on the Preset tab and the Preset dialog will appear Preset From the Preset menu i you can select save and Save Current As delete presets stored in d Delete Preset the OmniaONE unit These are the same operations that can be performed from the OmniaONE s front panel but consolidated on a single menu TCPAP connectioi ed Current p To select a preset and put it on the air double click on it in the preset list or highlight it and click the Select button Note In the current software when selecting presets from the remote the Preset name will not be refreshed on the OmniaONE s front panel To refresh the front panel preset name simply click the OmniaONE s jog wheel to ent
82. pts the current parameter CW CCW Press and hold the jog wheel for two seconds to switch between menu and meter screens Counter clockwise rotation moves the highlighting upward through the menu items and decreases the value when editing parameters OmniaONE Multicast Use and Operation Manual Version 0 90 25 Main Menu The OmniaONE menu system has been designed to be intuitive and simple to use Most operating parameters are found under one of the menu headings and sub headings allowing adjustments to be made quickly and with ease Rotating the jog wheel sequentially highlights each menu item in turn When the jog wheel is pressed inward clicked while a menu item is highlighted it will open that item s submenu Similar behavior occurs when selections are made within the various submenus To return to the previous level rotate the jog wheel clockwise until Exit is highlighted and then press the jog wheel inward Click This will return you to the next highest level in the menu structure NOTE Some of the longer menus have an Exit option at the top of the menu as well as at the bottom The OmniaONE Main Menu offers five selections Input Output Administrative Preset e Processing Input Output e Administrative e Lock Front Panel not visible in the above screenshot User Interface Tutorial Input Source Selection and Peak Level Setting The following two exercises are a useful introducti
83. put source if the currently selected one fails Failover Time is the amount of time that will elapse after the failure of audio on the primary input source before the unit makes the decision to switch to the secondary failover input source For instance if Failover Time is set for 5 seconds and the primary audio source fails 5 seconds later the unit will switch to the secondary audio input if that input is active If at any time audio is restored on the primary input for 1 second continuously the unit will switch back to the primary audio input It will remain with the primary input unless another failure is detected Fover Src Failover Source Failover Source selects which audio input Analog or AES EBU digital will serve as the secondary audio input Note that the audio input that is selected under Input Source above will always be the Primary audio input A source selected under Failover Source will always be the secondary source Anlg Level Analog Level Adjusts the master audio input level for the analog inputs which are derived from the rear panel XLR female input connectors See Proper Setting of Input Levels on Page 26 OmniaONE Multicast Use and Operation Manual Version 0 90 45 Right Trim Allows a 3dB adjustment of the right analog audio channel gain to correct minor left right balance problems in the input audio The left channel analog input gain is not affected by this control and is set using the mas
84. ration Manual Version 0 90 32 Chapter 4 Main Menu Selections This section presents an overview of the five Main Menu items Preset Processing Input Output Administrative and Lock Front Panel their submenus if any and details about each of the adjustable controls within Preset OmniaONE is equipped with a selection of factory presets that can be used to instantly configure the processing for common applications The currently loaded preset is displayed to the right of Preset on the top line of the Main Menu Highlighting Preset and clicking the jog wheel see Using the Jog Wheel on Pg 25 will open the Preset menu Rotating the jog wheel will scroll through all of the factory presets as well as any user presets that have been stored within the unit s non volatile memory The currently loaded preset will appear with square brackets around it Clicking the jog wheel will load the displayed preset into the OmniaONE instantly setting the various processing parameters To exit the Preset menu without loading a preset rotate the jog wheel clockwise until cancel is displayed and click In the Multicast there are two groups of factory presets Music and Talk Within each group there are presets for each of four bitrates commonly used by codecs following the OmniaONE 24 32 48 and 64 kbps By starting with one of the factory presets usually the one named closest to the primary programming and bitrate to be used on t
85. retained for future reference Heed Warnings warnings the product and those listed in the operating instructions must be adhered to Follow Instructions All operating and product usage instructions must be followed Heat This product must be situated away from any heat sources such as radiators heat registers stoves or other products including power amplifiers that produce heat Ventilation Slots and openings in the product are provided for ventilation They ensure reliable operations of the product keeping it from overheating These openings must not be blocked nor covered during operation This product should not be placed into a rack unless proper ventilation is provided through following the manufacturer s installation procedures Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool or the like Attachments Do not use any attachments not recommended by the product manufacturer as they may cause hazards Power Sources This product must be operated from the type of power source indicated on the marking label and in the installation instructions If you are not sure of the type of power supplied to your facility consult your local power company Grounding and Polarization This product is equipped with a polarized AC plug with integral safety ground pin Do not defeat the safety g
86. rity of both of the analog inputs or simply change the Invert setting to Both in the Input submenu of the Input Output menu OmniaONE Multicast Use and Operation Manual Version 0 90 AES EBU Digital Input AES EBU External Sync Input and AES EBU Output AES OUT RJ 45 Pinout e AES OUT Use Pins 1 2 GREEN Male XLR AES IN Use Pins 1 GREEN Female XLR i 2 L lt SYNC IN Use Pins 3 6 RED Female XLR L AES IN SYNC The digital AES EBU AES 3 inputs IN and EXT SYNC use industry familiar RJ 45 connectors and utilize the StudioHUB wiring standard They accept any sampling rate between 32kHz and 96kHz No user adjustment of the sample rate is necessary on the AES 3 input as a high quality digital sample rate converter is built in Individual channel gain and level setting for both analog and digital domains is done using the Input Gain software parameter settings in the Input Menu There is one AES 3 output on a standard RJ 45 connector that provides an output at selectable sampling rates Note The analog and digital outputs are active simultaneously More information about the StudioHUB wiring scheme can be found at http www studiohub com For your convenience a pair of XLR adaptor cables are supplied with the unit The male XLR lead with the GREEN shrink tubing is used for AES OUT The male XLR lead with the RED shrink tubing is not used The female XLR lead with the G
87. round in any manner Power Cord Protection Power supply cords must be routed so that they are not likely to be walked on nor pinched by items placed upon or against them Pay particular attention to the cords at AC wall plugs and convenience receptacles and at the point where the cord connects to the product Lightning For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the AC wall outlet This will prevent damage to the product due to lightning and power supply surges Overloading Do not overload AC wall outlets extension cords or integral convenience outlets as this can result in a fire or electric shock hazard 14 15 16 17 18 19 20 21 INSTRUCTIONS Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind into the product Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious damage to a child or adult and serious damage to the product Any mounting of the product needs to follow manufacturer s installation recommendations A Product and Cart Combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product a
88. rt A codec provisioning processor is in quite a different role than a conventional on air processor It is far more of a tool than a weapon OmniaONE Multicast Use and Operation Manual Version 0 90 29 The following sections are provided to assist you in designing personality of your sound As we said earlier there is no precise recipe for setting up audio processing because each application is different However there are a few basics that we can share with you that can help get you to where you want to go Setting up processing for the absolute best end product usually requires a concerted effort some extended periods of critical listening and making a few intelligently chosen and subtle changes over time It will be time and effort well spent and all you need to know up front is that you must Know your goals have a plan Take your time Always adjust deliberately and methodically Listen critically before making more adjustments VVVV Increasing Density Loudness Try to resist the temptation to crank up the aggressive processing sections They will definitely add loudness but usually at the cost of quality and intelligibility Many times just building a bit more RMS energy in the AGC sections will do the trick The following are some suggestions on where to begin to make changes For best results you should try them in the order we have listed below Increasing loudness can be accomplished in five ways 1 Alter t
89. s OmniaONE Key Front Panel Features Headphone Jack Headphone Level Control Jog Wheel Main Menu G R Metering LCD Display Level Meters Headphone Level Control A standard 4 TRS stereo headphone jack is located at the left side of the front panel and allows the processed signal to be monitored The Headphone volume level control is physically located to the right of the headphone jack The headphone amplifier itself is a high headroom design and is driven by its own high quality D A converter that is independent of the analog XLR outputs Therefore level changes in either output will not affect the other Level Meters amp Processing Bargraphs The top two of the three horizontal meters show digital sample accurate peak representations of the left and right channel input or output levels Whether these bargraphs are displaying Input Analog Output or AES EBU Output levels is selectable from within the Input Output menu A front panel indicator confirms which level view has been selected Input or Output The bottom horizontal meter marked comp aux is not currently used in the Multicast style OmniaONE Multicast Use and Operation Manual Version 0 90 23 Audio I O Level Display Either input or output levels can be displayed The highest LED illuminated indicates digital sample accurate peak signal levels The meters are calibrated in decibels below full scale digital 0 dBFS in 2dB steps 0 dBFS is the absolu
90. s for the OmniaONE are performed over an Ethernet connection using any standard Web Browser and an update file downloaded from the Omnia website The OmniaONE contains two software banks and the new OmniaONE Multicast Use and Operation Manual Version 0 90 68 software is always uploaded to the inactive bank This is safeguard against loss of power or other interruption during the update In this event the OmniaONE should still boot into the active bank containing the old software but it is best to avoid interruptions in any case To update the OmniaONE software proceed as follows 1 Download the OmniaONE software update file oup from the Omnia website at http www omniaaudio com support updates htm and save it to a convenient location on your computer 2 Make sure your OmniaONE s Network Configuration settings have been entered appropriately for your network see Network Configuration on Page 47 for details and connect your OmniaONE s Ethernet Livewire jack to your Ethernet network using a standard Cat 5 cable or directly to a computer using a Cat 5 crossover cable 3 Opena standard Web Browser on your computer and connect to the OmniaONE by entering http xxx xxx x xxx in the browser s address bar where the x s in the example above are replaced with the OmniaONE s IP address Once connected you should see the Login screen shown below Enter the Password the default is omnia all lower case and click o
91. several dozen processing parameters These adjustments alter the sound and texture of the audio Increasing any setting will lead to more aggressive processing For example a higher drive setting adds more gain into the dynamics section a higher attack or release setting means a faster time constant a higher gate threshold setting means more gating will occur and a higher farther to the right on the control setting for a filter means more filtering is occurring so the lowest frequency settings for a low pass filter are farthest to the right on the control Depending on the type of control adjusted and its range the changes you make can affect the sound in subtle or extreme ways Our advice is to make a limited number of changes at a time make those changes in small increments and then listen to the results for a period of time before making any further adjustments Keep in mind that should you get lost you can always go back to where you started by simply recalling the preset that you started with The factory presets cannot be overwritten lt Exit Click on this option to return to the Processing menu Pre processing HPF High Pass Filter The high pass low cut filter allows you to remove subsonic energy from the input audio prior to further processing In so doing intermodulation distortion performance of the processor and the audio path following it are improved and processing resources are not wasted processing inaudible s
92. sing screen of the OmniaONE s built in remote control applet This is a Java applet that requires Java Runtime Environment JRE from Sun Microsystems version 1 4 or higher to be installed on your computer Once JRE is installed lt the Remote Control applet is accessed through the OmniaONE s built in web page interface J ava via TCP IP The latest version of JRE for Windows Solaris Linux and Apple Mac OS is available here Once Java is installed on your computer using a Web browser connect to the IP address of your OmniaONE as follows see on Page 50 if you need to enter the Network parameters into the OmniaONE 1 Open a standard Web Browser on your computer and connect to the OmniaONE by entering http xxx xxx x xxx in the browser s address bar Please enter password to login where the x s in the example above are replaced Password with the OmniaONE s IP address Once connected you should see the Login screen Login Login 2 Enter the Password the default is omnia all lower case and click on the Login button Or simply press Enter OmniaONE Multicast Use and Operation Manual Version 0 90 63 The Main Menu should appear Remote Presets Update Configuration About Logout Click on the Remote link option from the top menu or Meters amp Remote Control option from the Main Menu Show live meter data and control all processor parameters Download and u
93. t generator to the output cables to verify analog digital audio is making it to the next device The next condition to check is to see if the failure has caused the processing to cease Using program material check to see if the processing bargraphs are operating If they are then it s a good indication that the basic DSP structure is sound and the system s host processor is working At this point it would be a good idea to see if the loss of audio is confined to only one output port e g the discrete left right outputs or the AES EBU output Check the signal at each of these locations If the signal is dead at all three then this points to a digital audio problem after the dynamic processing DSP chips If one of the output sections is not operating then it can be localized to that specific section Note The discrete left right outputs are operated from their own specialized Digital to Analog converters Therefore it s possible for one type of output to fail without affecting the other Likewise a failure in the AES EBU driver section could result in the digital output being dead while the rest of the system is operational OmniaONE Multicast Use and Operation Manual Version 0 90 59 Obtaining Service Omnia Customer Support personnel are available in Cleveland Ohio USA Monday through Friday between 9 00 A M and 6 00 P M Eastern Time If outside the U S A please contact the dealer you purchased your Omnia from Before c
94. te maximum level in the digital domain Levels from 34 dBFS to 14 dBFS are displayed in blue levels from 12 to 2 dBFS are displayed in yellow and 0 dBFS the clipping point is displayed in red Audio I O Level Display Processing Meter Display In Meter Display Mode the vertical bargraphs show all of the processing activity of the AGC and Limiter sections within the OmniaONE If the menu is currently displayed on the OmniaONE s LCD screen press and hold the jog wheel for two seconds and the processing meter display should appear as shown below To return to the menu display mode simply click the jog wheel once See Using the Jog Wheel on the next Page Notes For any meter except the Sensus and Final Limiter a change from a solid bar to a checkerboard pattern indicates a gated condition in that band The wideband AGC and four band AGCS will recover to a resting gain setting which coincides with the RTZ Return To Zero levels set for each band Processing Meter Display AGC Meters Limiter Meters W Wide Band L Low Band paca Low Band M Mid Band Mesne Mid Band Presence Band LN Presence Band H High Band Hs High Band Sensus Final Limiter OmniaONE Multicast Use and Operation Manual Version 0 90 24 Using Jog Wheel The main user control for the OmniaONE is the easy to use jog wheel with its integral push switch Using the control is both intuitive and
95. ter Analog Level control previously described AES Level AES EBU Level Adjusts the master audio input level for the AES Digital input which is derived from the rear panel RJ 45 StudioHUB connector See Proper Setting of Input Levels on Page 27 Right Trim Invert Allows a 3dB adjustment of the right digital audio channel gain to correct minor left right balance problems in the input audio The left channel digital input gain is not affected by this control and is set using the master AES Level control previously described Permits audio phase inversion to be performed in the following combinations None No Channel inversion is performed factory default Both Both left and right channel phase is inverted Both is typically selected if it sounds better to an announcer monitoring themselves in headphones using the output of the processing than None One of the two settings should The goal is to make the relative phase of the headphone feed more in phase with the announcer s own bone conduction Once set this setting should remain the same for all announcers using the same headphone feed L Only left channel phase is inverted R Only the right channel phase is inverted These settings are present as a convenience to correct 180 degree stereo phase errors in the input audio to the processor or in another device after the processor Mono Mode Allows input signal routing to be rec
96. to ascertain some preliminary information first before embarking on an in depth problem solving mission Take time to carefully consider whether your unit falls into any of the following states 1 The unit is totally dead Is the power on Is the line cord plugged into an outlet that has AC power Is there an audio input level Is there an audio output level Is there a power indication Is the LCD screen blank scrambled or not illuminated Symptoms like these might indicate a power supply problem If you wish to examine the power supply be aware that it is switching type and therefore requires a load in order to start up and operate properly Voltages measured when the power supply is not connected to the Omnia motherboard may not be correct 2 Theunit has power but there is no audio output although the processing bargraphs are working The first thing to verify is whether the front panel jog wheel is operational Verification of front panel operation helps narrow down where the problem is Look at the metering display If there is input audio but no output audio indications try cycling unit s power If that doesn t bring the operation back to normal then a hardware failure of some sort has occurred If you get output levels but have no output audio verify that the outputs are connected correctly An analog output connected to a digital device or a digital output connected to an analog device won t pass audio Connect the appropriate tes
97. ual Limiter band Used when you desire more or less density in a specific band These Limiter Drive controls can also be used as secondary dynamic EQ controls after the Drive controls in the AGC Xover To adjust the overall amount of density use the Overall Limiter Drive control in the Xover section See OV Lim Drv in the Xover Crossover section on Page 37 LFLim Att Low Frequency Limiter Attack The attack control adjusts how fast the limiter responds to sudden increases in audio level and higher numbers equate to faster response times Faster attack times reduce the transient nature of the input audio while slower attack times improve it Extremely slow attack times must be used with caution so as not to allow the Final Limiter stage to be overloaded during the time when the limiter is adjusting the level downwards LFLim Rls Low Frequency Limiter Release OmniaONE Multicast Use and Operation Manual Version 0 90 39 The release control adjusts how fast the limiter recovers from periods of more gain reduction when the input audio levels fall Faster release times higher numbers result in a more dense sound Even though the Omnia uses program controlled release algorithms setting the control for extremely fast release times while driving the limiter hard can result in pumping as well as extremely dense sounding fatiguing audio Also setting the control for extremely slow release times especially when combined wit
98. ult in loudest sound it gives the illusion of competitive loudness while still retaining a lot of detail and clarity To achieve this sound you should target most adjustments to the Limiter sections and avoid heavy use of the Final Limiter and fast settings in the AGC sections Using very fast attack and release times in the multi band limiters without pushing them beyond 5dB or so of gain reduction keeps IM distortion to a minimum and generates higher RMS levels This translates into higher perceived loudness On the other hand using larger amounts of drive to the multi band limiters along with faster release times will generate far more consistency and density Increases in final limiting depth more drive will further add to this The end effect is that the audio is now consistently loud at all times The drawback to this kind of sound is that when taken to extremes the excessive density can cause listener fatigue and add additional coding artifacts While OmniaONE Multicast is designed to minimize listener fatigue when adjusted to do so it is capable of generating large amounts of density that could eventually lead to listener fatigue Adding More Detail When Loudness Isn t The Last Word Now that we ve squished the grape lets look at what it takes to undo a signal that is being too heavily processed Basically we ll just be reversing the procedures listed above and in this order 1 Reduce the Drive to the Final Limiter
99. unctionality you only need a standard terminal program for DOS Windows or other operating system It must be configured for a default baud rate of 19200 no hardware handshaking and using a terminal emulation for VT100 At Omnia we commonly use the Hyperterminal program that ships with Microsoft Windows but you can use whatever program you are familiar with Please see the examples below for how we ve set up our connection Omnia6 Properties ConnectTo Settings COM1 Properties 2l x Function arrow and ctrl keys act as C Windows keys Data bits Parity None Stop bits hn rl Elow control None m Restore Defaults Cancel Apply Bits per second Backspace key sends Del Space Ctrl H Emulation Terminal Setup Colors Telnet terminal ID fansi Backscroll buffer lines so ES Play sound when connecting or disconnecting Egit program upon disconnecting ASCII Setup ten Once these parameters have been entered and saved as a connection profile they can be used to capture and display and print the output of the OmniaONE s RS 232 internal serial port during boot up Diagnostics and Error Messages To run a system diagnostics check of the OmniaONE unit that can be used by Telos Omnia Customer Support personnel in case of difficulty with the unit click on the Factory Diagnost
100. us about applying too much as the resonant frequency of many automobile interiors lies in this frequency range Also too much can cause excessive gain reduction in the following 4 Band AGC stage A little can give a nice subtle warmth enhancement to voices and other program material that may otherwise sound too thin Click on this option to return to the Adjust Processing submenu Xover Crossover The crossover splits the audio signal into 4 independent bands to enable optimum processing for the bass L midrange M presence P and treble H frequency ranges There are two four band processing stages that share the same crossover The crossover points are 180Hz IkHz and 3 7kHz The first stage 1s the 4 Band AGC Automatic Gain Control stage This stage operates on the average level letting faster peaks through to the following limiter stage It dynamically equalizes the program material to add consistency while gently building up density to keep the following peak limiter stages from working too hard The output of each of the 4 Band AGC bands directly feed their corresponding peak limiter stage The 4 Band Limiter stage operates on the peak levels of the program material with each band optimized for its frequency range controlling peak levels for the following Sensus and Final Limiter stages Low Drive Adjusts the amount of gain reduction in the Low Band AGC Higher numbers result in more drive and because of the increased compressi
101. verwrite this existing configuration with your changes just rotate the jog wheel clockwise to highlight the Save button and click Your changes will be saved to the existing configuration preset If instead you wish to save your changes as a new configuration preset with a different name click the jog wheel while Name is highlighted and the editing cursor will appear highlighting the first character of the existing preset name This is select mode If no previous configurations were saved lt none gt will vanish and be replaced by the editing cursor If an existing preset name is present you can scroll left and right through its text by rotating the jog wheel knob Be careful not to scroll clockwise past the blank space just after the last character in the name or select mode will be cancelled If this happens simply rotate the knob counter clockwise until Name is highlighted and click to re enter select mode When you reach the character you want to edit click This puts the cursor in edit mode You can now change that character by scrolling through the character list with the knob When the desired OmniaONE Multicast Use and Operation Manual Version 0 90 48 character is found click This will return cursor to select mode and you can again turn knob to select the next character to edit To delete a character Select the character to be deleted click choose the symbol and
102. what the codec or bitrate is Important Note 1 It is extremely important to never directly audition the output of the OmniaONE Multicast for audio quality without the audio being first routed through a codec Why The processed output of the OmniaONE Multicast has been pre corrected for the characteristics of the following codec and because of this the audio may contain strange sounding artifacts that will imitate the inverse of what that codec will do Because of this the audio exiting the OmniaONE Multicast may be unpleasant to listen to and will certainly be inferior to that which will exit the codec later on In other words what you hear at the output of the OmniaONE Multicast will bear no relationship to the audio quality that will be achieved after the audio has passed through the coding process Need a corollary to this It s like trying to taste a pizza while still in the grocery store and staring at the raw ingredients that haven t been purchased yet Thank you for selecting the incredible OmniaONE Multicast Audio Processor Your continued patronage and support are appreciated Sincerely The Omnia Development Team OmniaONE Multicast Use and Operation Manual Version 0 90 11 10 1 12 13 SAFETY Read Instructions All safety and operating instructions must be read before operating the product Retain All Instructions All safety and operating instructions must be

Omnia Industries Food Processor Omnia One Multicast Stero Audio Processor with SENSUS User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents