Oki BTX-208 User's Manual
Contents
1. 9910 Fax 1 714 799 9533 United Kingdom OK International Ltd Eagle Close Chandlers Ford Hampshire S053 4NF U K Tel 44 0 23 8048 9100 Fax 44 0 23 8048 9109 France OK International SA Rue de la Saone Zac De Folliouses Les Echets 01706 Miribel Cedex France Tel 33 0 4 72 26 20 30 Fax 33 0 4 72 26 20 35 Germany OK International GmbH Frankfurter Strasse 74 D 64521 Gross Gerau Germany Tel 49 0 61 52 71 12 0 Fax 49 0 61 52 71 12 22 Italy OK International Strada Statale 11 No 28 20010 Vittuone Milano Italy Tel 39 02 9025161 Fax 39 02 90111147 Singapore OK International Sales Support Office 10 Ang Mo Kio St 65 03 18 19 Techpoint Singapore 569059 Tel 65 62810991 Fax 65 62853473 China OK Electronics Beijing Co Ltd No 1 Bidi A 10 Long Qing Street Beijing Econ amp Tech Developing Zone Beijing 100176 P R China Tel 86 10 67878490 Fax 86 10 67878491 Japan OK International Japan Co 5 3 1 Heiwajima Ota ku Tokyo 143 0006 Japan Tel 81 3 5753 0085 Fax 81 3 3765 88552. BI X 208 Fume Extraction System System User Guide page FUENTE 2 ITEMS Supplied rornrrnnnrnrannvrnannvvnnnrnvnnrnvnnnrnnannennansnnnnnsnnnnnennnnene 2 Per 2 lg SEN 16 OE 2 Operation and Maintenance rarrrnnnnrnnnnnrnrnnnnnnnnennnnnnnnnnnnnnnnennnn 2 AMAT le 2 TROUDISSMOOUING EE 3 CCIM CAN AA EE 3 Part full 4 VTM E 4 So need peer FEE EE NE 4 OK INTERNATIONAL www okinternational com For Your Safety For safe and successful operation of the unit read these instructions completely If the instructions are not observed the manufacturer can assume no responsibility Retain this manual for future reference Always disconnect the power supply before servicing the unit Do not operate the Unit without filter inserts Contaminants in the extracted air will damage the blower Use only original equipment filters The BVX 208 is designed for the removal of solder fumes Use filter unit only for this purpose Consult your safety department when using the unit on flammable gases This unit is not explosion safe and can only be used for the extraction of vapors which have concentration levels well below the lower explosive limits This system is equipped with automatic reset overload protection which may cause the unit to restart automatically While under warranty the unit may be repaired only by an authorized Metcal Service Representative Items Supplied 1 Filter Unit with filters installed 1 32mm hose adapt
3. Certification UL CSA CE Part Numbers BTX 208 Filter Unit tip extraction for 8 stations 100 240V 50 60Hz Replacement Filters FP BVX200 Pre filter Pack of 5 FM BVX200 Main filter HEPA 99 95 Carbon Duct Connection Kits BTX CK2 25 Hose connection kit 2 4 stations 2 5m 8 long BT X CK4 50 Hose connection kit 4 8 stations 5m 16 long BT X CK4 75 Hose connection kit 2 4 stations 7 5m 25 long For Iron Adapter Kits contact your OK International Sales Representative Warranty OK International warrants the BTX 208 system against any defects in materials or workmanship for one 1 year from the date of purchase by the original owner This Warranty excludes normal maintenance and shall not apply to any opened misused abused altered or damaged items If the product should become defective within the warranty period OK International will repair or replace it free of charge at its sole option The repaired or replacement item s will be shipped freight prepaid to the original purchaser The warranty period will start from the date of purchase If the date of purchase cannot be substantiated the date of manufacture will be used as the start of the warranty period For the repair or return of a unit a Return Material Authorization Number RMA needs to be obtained Contact Information For Sales amp Customer Care North America OK International 12151 Monarch Street Garden Grove CA 92841 USA Tel 1 714 799
4. er 1 air inlet cover installed on second air inlet port 1 Power Cord 1 Operating Manual Description 1 ON OFF switch 2 Power Output 3 32mm hose adapter 4 air inlet cover with bypass valve 5 latch front and back Installation Place filter unit 1 at a location which minimizes length of ducting Screw supplied hose adapter into open air inlet port 2 Install ducting 3 as per duct installation instructions Install iron adapter kits 4 Connect filter unit to power supply 5 Operation and Maintenance e Turn unit ON e Check if the motor pump indicates an acoustical fluttering effect If yes open air by pass valve on air inlet cover until fluttering sound Ar disappears Do not open too much as this will reduce the airflow le performance The fluttering does not cause any damage to the system Maintenance The airflow of the filter unit decreases during operation due to several reasons e Clogging of vacuum tubes and hoses attached to solder iron e Saturation of pre and main filter inside filter unit Tip Extraction Accessories Clean stainless steel vacuum tubes 1 periodically and frequently Cleaning brushes are supplied with the iron adapter kits Inspect vacuum hoses 2 visually and clean if needed Replacement of filters If after cleaning of accessories the fumes are not extracted efficiently replace filter s inside filter unit Initially replace the pre filter onl
5. y If this step does not sufficiently improve the airflow then replace the main filter HEPA Carbon 1 Turn unit off Disconnect the power cord Unlatch the filter cover 1 Remove filter cover Replace the filters Pre filter main filter Make sure 1 to place main filter inside the alignment pins 2 so that interlock switch 3 is depressed 6 Replace filter cover and ensure proper fit on bottom housing Hook both latches into filter cover and press down carefully NR f Caution Do not use force If latches do not close check proper seating of 2 filter cover on bottom housing 7 Reconnect power cord and turn system on 8 If unit does not operate refer to troubleshooting section Hurra Notice Always use new replacement filters For disposal of used filters follow local environmental and safety requirements Troubleshooting Possibly Cause Solution o Z No air flow No Power Check On Off Switch Interlock switch Check power outlet open Check power cord Check filter Check safety interlock switch Little air flow Clogged tubes Clean extraction tube at solder iron hoses Clean vacuum hoses Air leak Check duct connections for leaks Housing not closed correctly Technical Data Max number of stations 8 Flow rate per station gt 28 lit min Noise Level lt 55 dBA Dimensions WxDxH 508 x 254 x 388 mm Weight 9 kg 20 Ibs Voltage 100 240 VAC Frequency 50 60 Hz Power 85 Watt
Download Pdf Manuals
Related Search