Ocean Electronic Tabletop Heater User's Manual
Contents
1. Fix the regulator to the tank housing with the M5X10mm bolt amp M5 nut 5 1 Fix 3pcs pins of 60mm length to the emitter screen with 3pcs M6 flange nuts then tighten them 6 1 Put the emitter screen on the burner 6 2 Use 4pcs 3 16 bolts to connect the emitter screen to the burner Tighten the bolts 7 1 Put the guard on the burner through the emitter screen 8 1 Put 3pcs washers on each 7 2 Put the ends of the guard pins of the 60mm length into the holes of the burner 9 1 Put the reflector through the pins and on the washers STEP 11 11 1 Turn off the control knob of the burner 11 2 Fix the 1 02Lbs gas tank not included to the regulator rotate the gas tank clockwise toward the regulator until tighten it STEP 10 10 1 Fasten the reflector with 3pcs M6 Castle nuts STEP 12 12 1 Close the door plate and lock it with the handle rotate the handle 90 degree SAFETY FIRST Read and become familiar with this entire manual especially the following precautions Caution this appliance is for outdoor use only outside any enclosure Always make sure there is fresh air ventilation Use only outdoors in a well ventilated space never use in a building garage or any other enclosed area Always maintain atleast 18 clearance top and 24 clearance side from combustible materials Always place heater on a hard and level surface Do not use if the wind velocit2. visible at night Burner will display tongues of blue flame These flames should not be yellow or produce thick black smoke indicating an obstruction of airflow through the burners If yellow flame is detected turn off heater and gas supply and consult Troubleshooting Re lighting Note For your safety Control Knob cannot be turned Pilot without first depressing Control Knob in Off position and then rotating to Pilot 1 Turn Gas Control Knob to Off 2 Wait 5 minutes to let gas dissipate before attempting to relight burner 3 Repeat the Lighting Steps 2 and 3 1 Rotate Gas Control Knob to Off position Normally burner will make a slight popping sound when extinguished 2 Remove Door Plate 3 Unscrew gas line from regulator 4 Close Door Plate Note After use some discoloration of the emitter screen is normal AFTER OPERATING Gas control is in OFF position Disconnect Gas line Heater is upright in a secure location MAINTENANCE To enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis Inspect the visible portion of the hose before each use of the appliance Inspect the entire hose assembly at least annually Air flow must be unobstructed Keep controls burner and circulating air passageways Clean Signs of possible blockage include Gas odor with extreme yellow tipping of flame Hea
3. He i jm Tabletop Heater Safety First Read and become familiar with this entire manual a Via H ME 1 888 775 1330 Distributed by RTA International Youngtown AZ 85363 TABLE OF CONTENTS Read These Safety INStructions cc cece cece eect eee e ees 1 Contents BreakdOWn nsssannnrrnssnrrrrnsnnrrrrrrnnrrrrssnrrrrsen gt 2 Screw Packing LIST as sre ree oe cist on cere cian ee nea eO NE ENTA 3 Assembly Procedule ccccccc eee eeeeceeeeeeeesssaeeeeeneeeuuganes 3 ASSEMDIY 00 cece cece ccc ce eee eens ne eee ee eee esssaeeeeeeeteagaeeeeeeneegas 4 Ly IS E E E E E snes demseecesnendentence 7 Tabletop Heater LocCation cc cece cece eee eee eee eeeeeeeeeneees 8 CHECKING For Ca Suro etoatetnectrcsaredes cinerea eenceviauetunenewopesces 8 Before 6121 62 9 6 panne ee een ee ne eee ne ee eee 8 812 6211 96 Pee eee ee ene ne ee ee een ee N eee eee 9 After ODS Fa race sec pence po eccacectaseestasoreueseraeseucesbaseccsnonat 11 MaintenaNG 6 wcanccocsnccctenccocnnaracmnaeaseneaaens E a REEE 11 DO e E E E E OTE 11 del 9 86 lt 5 619 a 6 eee ene nen eer ne ere ene 12 All rights reserved No part of this manual may be reproduced transmitted stored in a retrieval system or translated into any language in any form by any means mechanical optical electronic recording or otherwise without the written permission of Changzhou G
4. LEM PROBABLE CAUSE Pilot will not light Tank fuel empty Opening blocked Air in supply system Loose connections Pilot will not stay on Debris around pilot Loose connections Thermocouple bad Gas leak in line Lack of fuel pressure Burner will not light Pressure is low Opening blocked Control not ON Thermocouple bad Pilot light assembly bent Not in correct location SOLUTION Replace LPG tank Clean or replace opening Purge air from lines Check all fittings Clean dirty area Tighten connections Replace thermocouple Check connections Tank near empty Replace LPG tank Tank near empty Replace LPG tank Remove and clean Turn valve to ON Replace thermocouple Place pilot properly Position properly and retry
5. ardensun Furnace Co Ltd Changzhou Gardensun Furnace Co Ltd Reserves the right to revise this manual and to make changes to any or all parts at any time without obligation to notify any person or entify of such revision and changes Copyright 2006 Changzhou Gardensun Furnace Co Ltd 2006 Edition the front page READ THESE SAFETY INSTRUCTIONS If you smell gas Shut off gas to the appliance Extinguish any open flame Open lid If odor continues immediately call your Gas supplier or your life Department WARNING Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury death or property damage ATTENTION Only to be used outdoors Warning Accessible parts may be very hot Keep young children away Turn off the gas supply at the gas container after use Any modification of the appliance may be dangerous FOR YOUR SAFETY Gas leaks may cause a fire or explosion can cause serious bodily injury or death or damage to property You must follow all leak checking procedures operating this unit Never use an open flame to check for leaks WARNING Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance Danger Carbon monoxide hazard 1 This appliance can produce carbon monoxide which has no odor 2 Using it in an enclosed space can kill you 3 Never use thi
6. nd do not leak Wind velocity is below 10 mph Outdoor temperature is greater than 40 degrees F Heater is outdoors outside any enclosure There is adequate fresh air ventilation Heater is away from gasoline or other flammable liquids or vapors Heater is away from windows air intake openings sprinklers and other water sources Heater is atleast 18 clearance top and 24 clearance side from combustible materials Heater is on a hard and level surface There are no signs of spider or insect nests All burner passages are clear All air circulation passages clear Children pets clothing flammable materials and items that can be damaged from radiant heat are away from the heater Children and adults in the area have been alerted to the high temperature hazards especially burns and clothing fires Children and adults in the area have been warned not to touch heater near emitter during operation and until unit has cooled OPERATION Inspect the visible portion of the hose before each use of the appliance Inspect the entire hose assembly at least annually Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY DO NOT use it inside a building garage or any other enclosed area Make sure surrounding areas are free of combustible materials gasoline and other flammable liquids Ensure that there is no obstruction to air ventilation Be sure all gas connections are tigh
7. ng operation do not touch burner assembly The surface of heater s emitter can reach temperatures approaching 1600 F After shutdown do not touch burner assembly until heater has cooled approximately 45 minutes after use TABLETOP HEATER LOCATION e The tabletop heater is primarily for outdoor 24 use only Always ensure that adequate fresh air ventilation is provided e Always maintain proper clearance to combustible materials i e top 45 cm 18 and sides 60 cm 24 minimum WALL e Tabletop heater must be located on a stable and strong table e Never operate heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored CHECKING FOR LEAKS Make 1 2 oz of leak solution by mixing one part liquid dishwashing soap and 3parts water Spoon several drops or use squirt bottle of the solution onto the regulator canister connections Inspect the connections and look for bubbles If NO bubbles appear the connection is safe If bubbles appear there is a leak Loosen and re tighten this connection Re check for a leak If you continue to see bubbles after several attempts disconnect propane source BEFORE OPERATING am familiar with entire owner s manual and understand all precautions noted in Safety First All components are properly assembled intact and operable No alterations have been made All gas connections are secure a
8. s appliance in an enclosed space as camper tent car or home Do NOT touch or move heater for at least 45 minutes after use Dome is hot to the touch Allow dome to cool before touching CONTENTS BREAKDOWN Item Item No Item Qty No Item Qty 1 M6 Castle nut 3 11 Burner 1 2 Reflector 1 12 3 16 bolt 4 3 O6mm Washer 3 13 M5x10mm bolt 1 4 Emitter screen 1 14 Tank Housing 1 5 Guard 1 15 Igniter button 1 6 Door Plate 1 16 Control knob 1 7 Base 1 17 Handle 1 8 Cast Iron 1 18 Regulator 1 9 M6x15mm bolt 4 19 60mm pin 3 10 3 16 bolt 4 20 M6 flange nut 3 SCREW PACKAGING LIST ltem Qty ltem Qty M6 Castle nut 3 M5x10mm bolt amp M5 nut 1 O6mm Washer 6 60mm pin 3 M6x15mm bolt 4 M6 flange nut 3 3 16 bolt 8 Wrench 1 ASSEMBLY PROCEDURE Tools needed not included Adjustable opening wrench 2 20 cm long Slip joint pliers 23 cm long Philips screwdriver w medium blade Teflon plumbing tape for joints ASSEMBLY 1 1 Take out all the parts of the tabletop Heater 1 2 Aim the cast iron at the holes on the base 3 1 Put the burner on the tank housing then fix them with 4pcs 3 16 bolts 2 1 Use 4pcs M6X15mm bolts to fix the tank housing to the base amp cast iron 2 2 Tighten the bolts as above show 4 1
9. t and there are no leaks Be sure the access panel is clear of debris Be sure any component removed during assembly or servicing is replaced prior to starting Before Lighting Heater should be thoroughly inspected before each use and by a qualified service person at least annually If relighting a hot heater always wait at least 5 minutes for gas to dissipate Lighting 1 Turn Gas control knob to Off position 2 Pushin and rotate the Control Knob to Pilot position Depress igniter button 3 Once burner is lit hold Control Knob in for at least 30 seconds and release 4 If burner does not stay lit turn to Off position and wait 5 minutes and repeat 2 and 3 5 Once burner is lit rotate Knob to desired heating level LO low HI high If you experience any ignition problem turn off the heater and gas supply and consult Troubleshooting on page 12 Caution Avoid inhaling fumes emitted from the heater s first use Smoke and odor from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The heater should NOT produce thick black smoke Note The burner may be noisy when initially turned on To eliminate excessive noise from the burner turn the Control Knob to the LOW position Then turn the knob to the level of heat desired When heater is ON Emitter screen will become bright red due to intense heat The color is more
10. ter does NOT reach the desired temperature Heater glow is excessively uneven Heater makes popping noises Spiders and insects can nest in burner or orifices This dangerous condition can damage heater and render it unsafe for use Clean burner holes by using a heavy duty pipe cleaner Compressed air may help clear away smaller particles Carbon deposits may create a fire hazard Clean dome and emitter with warm soapy water if any carbon deposits develop Note In a salt air environment such as near an ocean corrosion occurs more quickly than normal Frequently check for corroded areas and repair them promptly Keep exterior surfaces clean STORAGE Between uses Turn Control Knob OFF Disconnect LP source Store heater upright in an area sheltered from direct contact with inclement weather such as rain sleet hail snow debris If desired cover heater to protect exterior surfaces and to help prevent build up in air passages Note Wait until heater is cool before covering During periods of extended inactivity or when transporting Turn Control Knob OFF Disconnect LP source and move to a secure well ventilated location outdoors Store heater upright in an area sheltered from direct contact with inclement weather such as rain sleet hail snow dust and debris If desired cover heater to protect exterior surfaces and to help prevent build up in passages TROUBLESHOOTING PROB
11. y is greater than 10 miles per hour Unit will operate at reduced efficiency below 40 F 57 Keep sprinklers and other water sources away from burner and controls Always use extreme caution when near heater Alert both children and adults to the hazards of high temperatures especially to avoid burns or clothing catching fire Young children and pets should be carefully supervised when they are in the area of heater Do not place clothing or other flammable materials either on or near heater Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater Certain materials or items when stored under heater will be subjected to radiant heat and could be seriously damaged Do not alter heater in any manner The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer Inspect heater before each use If a damaged part is detected do not operate until an original equipment replacement part has been properly installed Use of unauthorized parts will void warranty and create an unsafe condition Do not attempt to use this appliance without a functional factory supplied gas regulator in place If regulator becomes damaged use only a factory supplied replacement Prior to operating heater replace any guards or protective devices removed for servicing Duri
Download Pdf Manuals
Related Search