NuTone CI-365 User's Manual
Contents
1. Nulone INSTALLATION INSTRUCTIONS READ amp SAVE THESE INSTRUCTIONS VacPan Automatic Dustpan Inlet MODEL CI 365 READ INSTRUCTIONS BEFORE INSTALLATION IMPORTANT NOTES For maximum clearance under cabinets use 2 1 2 X 3 1 2 short 90 elbow Check for an air tight seal at VacPan and elbow prior to installation If required use Teflon tape to make air tight seal but do not use glue Make certain clearance is available in kick space prior to installation under cabinets Use central vacuum cover plate or double electrical blank plate for access cover when required Allow 1 2 play in vacuum pipe at location of VacPan so that fitting connection can be lifted to install or remove VacPan oOo fF W DY a BRASS TERMINAL CONTACT SPRING TERMINAL CONTACT FIGURE 1 INSTALLATION OPTION 1 UNDER CABINET ACCESS TO PIPING FROM BELOW Refer to Figure 2 1 Select a location under cabinet for VacPan 6 so that new fittings can be connected to existing pipe Drill small reference hole under location of VacPan to determine position in basement or crawl space 2 Using a hole saw cut access hole 3 in floor under cabinet Position access hole 3 so that final fittings 7 can be installed by reaching through access hole 3 Cut 6 3 4 long slot along kick 4 of cabinet Make terminal connections 5 Slide VacPan 6 into slot and secure using 6 painted wood screws provided Reach t2. From below use hole saw to remove wood floor and wood plate at location of VacPan between studs in wall cavity to provide access hole 3 from below 5 Using a 11 2 hole saw remove a 6 3 4 long slot 4 in baseboard tight to one stud FIGURE 3 Refer to Figure 4 6 Make wire connections to brass terminal and sprig terminal screws 5 7 Secure VacPan 6 to baseboard using 6 screws provided 8 From below reach through hole 3 in stud space and push elbow 7 onto VacPan 6 9 Make piping connections 8 as required to tie into existing central vac piping FIGURE 4 INSTALLATION NEW HOME CONSTRUCTION Refer to Figure 5 1 Cut out wall plate 9 between two studs at the location of VacPan Cut a6 3 4 piece of wall plate and refasten to floor temporary rough in block 10 This will act as temporary rough in block that will force all trades to finish around providing a slot in wall for installation of VacPan Make certain that screws 11 remain exposed so that block can be removed in the future 2 Flooring contractor must run flooring under block 3 Rough in pipe and low voltage leads 12 to location of VacPan outlet Ensure final fitting is installed 1 off finished floor with 1 2 of play in piping to allow VacPan to be slid into position FIGURE 5 Refer to Figure 5 1 If ceiling is installed below and access to pipe is not possible cut 2 3 4 X 4 1 2 access hole 13 in wall above
3. VacPan 6 Reach through access hole lift pipe and slide VacPan into position and push elbow onto VacPan 2 Cover access hole with cover plate 14 FIGURE 6 Product specifications subject to change without notice 4820 Red Bank Road Cincinnati Ohio 45227 1140 Tristar Drive Mississauga Ontario Canada L5T1H9 Printed in U S A Rev 3 02
4. hrough access hole 3 and make final fitting connections 7 oy a IF ACCESS CANNOT BE MADE FROM BELOW 1 Rough in pipe 8 through floor provide 1 2 play in pipe 2 Provide slack in low voltage lines for future connection 3 Once cabinets are installed cut access hole 13 and cover with cover plate 14 Reach through and make final connections as per previous installation FINAL FITTING 3 COVER ACCESS PLATE CONNECTIONS IF REQUIRED ACCESS CANNOT BE MADE FROM BELOW CABINET v HATCHED AREA REPRESENTS ROUGH IN PIPING IN PIPE oe D 6 VACPAN k Do lt N gt lt 7 lt a ke SUBFLOOR 6 TERMINAL ana ACCESS HOLE IN SUBFLOORING CONNECTIONS UNDER CABINET JOIST SPACE TO CENTRAL VAC gt a a R m a A e D n s a D a e m m eee e e a e m e a g a n A a A ee o a eee Oe Se e D E Ly CEILING IS INSTALLED PROVIDE COVER PLATE IN BOTTOM OF CABINET TO MAKE FITTING CONNECTIONS IF CEILING IS NOT INSTALLED FINAL FITTING CONNECTIONS CAN BE MADE THROUGH ACCESS HOLE IN FIGURE 2 SUBFLOOR INSTALLATION OPTION 2 INWALLS ALONG BASE BOARDS Refer to Figure 3 ACCESS TO PIPING FROM BELOW 1 Locate studs 1 in the wall at the location VacPan will be installed 2 VacPan should be located tight to one side in stud space 3 Drill a small reference hole 2 through the floor under area of VacPan This will establish location from basement 4
Download Pdf Manuals
Related Search